Focusing on the phenomenon of gypsum rain while wet desulphurization(WFGD) were adopted in coal fired power plant without GGH, the paper studied and put forward the solutions : (1) desulfurization facilities related e...Focusing on the phenomenon of gypsum rain while wet desulphurization(WFGD) were adopted in coal fired power plant without GGH, the paper studied and put forward the solutions : (1) desulfurization facilities related equipment modification;(2) optimal operation of existing desulfurization facilities.展开更多
On-site measurements of volatile organic compounds(VOCs)in different streams of flue gas were carried out on a real coal-fired power plant using sampling bags and SUMMA canisters to collect gas samples,filters to coll...On-site measurements of volatile organic compounds(VOCs)in different streams of flue gas were carried out on a real coal-fired power plant using sampling bags and SUMMA canisters to collect gas samples,filters to collect particle samples.Gas chromatography-flame ionization detector/mass spectrometry and gas chromatography-mass spectrometry was the offline analysis method.We found that the total mass concentration of the tested 102 VOC species at the outlet of wet flue gas desulfuration device was(13456±47)μg·m^(-3),which contained aliphatic hydrocarbons(57.9%),aromatic hydrocarbons(26.8%),halogen-containing species(14.5%),and a small amount of oxygen-containing and nitrogencontaining species.The most abundant species were 1-hexene,n-hexane and 2-methylpentane.The top ten species in terms of mass fraction(with a total mass fraction of 75.3%)were mainly hydrocarbons with a carbon number of 6 or higher and halogenated hydrocarbons with a lower carbon number.The mass concentration of VOC species in the particle phase was significantly lower than that in the gas phase.The change of VOC mass concentrations along the air pollution control devices indicates that conventional pollutant control equipment had a limited effect on VOC reduction.Ozone formation potential calculations showed that aromatic hydrocarbons contributed the highest ozone formation(46.4%)due to their relatively high mass concentrations and MIR(maximum increment reactivity)values.展开更多
The development of electrical engineering and electronic, communications, smart power grid, and ultra-high voltage transmission technologies have driven the energy system revolution to the next generation: the energy ...The development of electrical engineering and electronic, communications, smart power grid, and ultra-high voltage transmission technologies have driven the energy system revolution to the next generation: the energy internet. Progressive penetration of intermittent renewable energy sources into the energy system has led to unprecedented challenges to the currently wide use of coal-fired power generation technologies. Here, the applications and prospects of advanced coal-fired power generation technologies are analyzed. These technologies can be summarized into three categories:(1) large-scale and higher parameters coal-fired power generation technologies, including 620/650/700 oC ultra-supercritical thermal power and double reheat ultra-supercritical coal-fired power generation technologies;(2) system innovation and specific, highefficiency thermal cycles, which consist of renewable energy-aided coal-fired power generation technologies, a supercritical CO_2 Brayton cycle for coal-fired power plants, large-scale air-cooling coal-fired power plant technologies, and innovative layouts for waste heat utilization and enhanced energy cascade utilization;(3) coal-fired power generation combined with poly-generation technologies, which are represented by integrated gasification combined cycle(IGCC) and integrated gasification fuel cell(IGFC) technologies. Concerning the existing coal-fired power units, which are responsible for peak shaving, possible strategies for enhancing flexibility and operational stability are discussed. Furthermore, future trends for coal-fired power plants coupled with cyber-physical system(CPS) technologies are introduced. The development of advanced, coal-fired power generation technologies demonstrates the progress of science and is suitable for the sustainable development of human society.展开更多
Nowadays, the worsening environmental issue caused by CO2 emission is greatly aggravated by human activity. Many CO2 reduction technologies are under fast development. Among these, monoethanolamine (MEA) based CO2 cap...Nowadays, the worsening environmental issue caused by CO2 emission is greatly aggravated by human activity. Many CO2 reduction technologies are under fast development. Among these, monoethanolamine (MEA) based CO2 capture technology has been paid great attention. However, when connecting the CO2 capture process with a coal-fired power plant, the huge energy and efficiency penalty caused by CO2 capture has become a serious problem for its application. Thus, it is of great significance to reduce the related energy consumption. Based on an existing coal-fired power plant, this paper proposes a new way for the decarburized retrofitting of the coal-fired power plant, which helps to improve the overall efficiency of the power plant with less energy and efficiency penalty. The decarburized retrofitting scheme proposed will provide a new route for the CO2 capture process in China.展开更多
Steam is the typical working fluid to drive turbo-generators in coal-fired power plants. It is an effective working fluid, but some of its energy is extracted in an unusable form when condensed. A Power Recovery ...Steam is the typical working fluid to drive turbo-generators in coal-fired power plants. It is an effective working fluid, but some of its energy is extracted in an unusable form when condensed. A Power Recovery Cycle (PRC) using a more volatile Secondary Working Fluid (SWF) added to the steam cycle could improve energy efficiency. PRCs have been applied to the flue gas and for combined cycle systems but not to traditional plant steam cycles. This paper details an analysis of adding a steam cycle PRC to a 500 MW lignite coal-fired power plant. A validated model of the plant was developed and PRCs using the three most attractive SWFs, benzene, methanol and hydrazine, were then added to the model. Adding a benzene, methanol, or hydrazine steam cycle PRC will produce an additional 59, 34, and 49 MW, respectively. An AACE Class 4 factored broad capital cost estimate and comparable operating costs and revenue estimates were developed to evaluate PRC feasibility. The benzene, methanol, and hydrazine processes had 2019 Net Present Values (NPVs) @12% of -$32, -$59, and +$35 million ± 40%, respectively. Thus, a PRC may be profitable at current or modest increases to U.S. Upper Midwest electricity prices of around $0.0667/kWh.展开更多
With a particular reference to China Huaneng Group's practices in CO_2 capture, this article presents a brief ing on the current development of CO_2 capture technologies in coal-fired power plants both in China an...With a particular reference to China Huaneng Group's practices in CO_2 capture, this article presents a brief ing on the current development of CO_2 capture technologies in coal-fired power plants both in China and abroad. Sooner or later, the integration of CO_2 capture and storage (CCS) facility with coal-fired power plant will be inevitably put on the agenda of developers.展开更多
According to statistics, the average dust collection efficiency of flue gas emission in the large and medium- sized power plants in Zhejiang Province at present has attained higher than 97% which surpasses the 95% sta...According to statistics, the average dust collection efficiency of flue gas emission in the large and medium- sized power plants in Zhejiang Province at present has attained higher than 97% which surpasses the 95% standard as stipulated by the Ministry of Electric Power. The dust collection efficiency of the Beilungang Power Plant has already attained 99.92%. In recent years, Zhejiang Electric Power Corporation has stipulated that all the newly constructed generating units shall be equipped with high efficiency electrostatic precipitator (ESP) while the existing power plants shall speed up their renovation work for their dust collectors. In combination with the fourth stage project of the Taizhou Power Plant, the improvement work of the dust展开更多
Based on the Chinese thermal coal and power generation data,such as ultimate analysis,proximate analysis,low heat value(LHV)on as received basis,power generation volume,thermal coal consumption volume and net coal con...Based on the Chinese thermal coal and power generation data,such as ultimate analysis,proximate analysis,low heat value(LHV)on as received basis,power generation volume,thermal coal consumption volume and net coal consumption rate,several mathematical models for calculating CO 2 reduction by Chinese coal-fired power plants are established.Calculations of the CO 2 emission factor(CEF),the CO 2 emission volume and reduction volume are made according to these models.The calculation results reveal that between 1993 and 2010,the CO 2 emission volume reached 31.069 Gt,reduced by 0.439 Gt,averaging 28.83 Mt each year.展开更多
The physical,chemical and mineral facies properties of the flyash from Xiezhuang Coal Refuse Fired Power Plant have been studied by means of naked eyes,microscope,chemical composition analysis and XRD analysis,and com...The physical,chemical and mineral facies properties of the flyash from Xiezhuang Coal Refuse Fired Power Plant have been studied by means of naked eyes,microscope,chemical composition analysis and XRD analysis,and compared with that of the flyash from Taian Coal Fired Power Plant.The result shows that the flyash from coal refuse fired power plant is of better quality in making construction items,for being brighter in color,fine and high activity.Some ways of comprehensive utilization of the ash have been suggested in this paper.展开更多
Dry deposition samples were collected in a weekly basis during 2010 in a site located at the Mexican Pacific Coast: Manzanillo, Colima. Samples were collected with an automatic wet/dry deposition sampler using nylon f...Dry deposition samples were collected in a weekly basis during 2010 in a site located at the Mexican Pacific Coast: Manzanillo, Colima. Samples were collected with an automatic wet/dry deposition sampler using nylon filters as surrogate surfaces. Samples were extracted with deionized water and analyzed for pH, conductivity, Na+, K+, Ca2+, Mg2+, NH4-, NO3-, SO42- and Cl-. Nitrate and sulfate were the most abundant ions, contributing with 53% to the total ionic mass;and their levels exceeded the hemispheric background concentrations proposed for marine remote sites. The influence of the power plants burning combustoleo located upwind the sampling site was completely evident. From meteorological analysis, it could be observed that the sampling site was all time under the influence of power plants as a result of the effect of breezes. However, in spite of the high levels of NO3- and SO42- found in the samples collected, pH value average was almost neutral, with 28% of samples slightly acid. Potassium was the most abundant cation and from the quantification of the neutralization effect of the main alkaline components, the prevalence role of K+ was completely evident, suggesting the influence of the mining complex Pe?a Colorada located upwind the sampling site, where amyl xanthate potassium is used as collector in tailing dams. Dry deposition fluxes were estimated for all ions measured. Nitrogen dry deposition at Manzanillo is already in the upper extreme of the threshold value reported for sensible ecosystems. On the other hand, sulfur deposition exceeded slightly the critical load value reported for some ecosystems in Europe. Even at this moment, nitrogen and sulfur deposition is not a problem, it is necessary to take steps to avoid that total deposition of these elements exceeds critical loads, considering that results reported in this study not include the wet deposition fluxes.展开更多
In order to explore the changes in the growth and protein contents of Spirulina and obtain a proper strain for the fixation of carbon dioxide(CO2 from flue gas,the strains isolated from the Spirulina farms and the str...In order to explore the changes in the growth and protein contents of Spirulina and obtain a proper strain for the fixation of carbon dioxide(CO2 from flue gas,the strains isolated from the Spirulina farms and the strain 208 were cultured under different aeration conditions including no CO2,10%CO2 and coal power plant flue gas supplements.The physiological indexes including filament length,biomass yield and chlorophyll a,soluble protein and phycocyanin contents were determined,respectively.When cultured without CO2 supplement,the strain 4-5 exhibited the highest biomass yield(1.880 g L^(−1)and a specific growth rate(0.367 d−1.However,the specific growth rate of all strains decreased significantly when they were cultured under 10%CO2 and unfiltered coal power plant flue gas supplements.Considerable differences were noted in the performance of the experimental microalgal strains under different contemporaneous conditions.The strain 7-8 achieved the highest biomass yield(1.603 g L^(−1)and relatively high phycocyanin content(7.1%)under 10%CO2 supplement.We noted that strain 4-5 had the highest specific growth rate(0.182 d−1 and biomass yield(0.43 g L^(−1)under coal power plant flue gas supplement.Strain 6-10 displayed the highest soluble protein content(66.02%),and strain 7-8 showed the highest phycocyanin content(9.28%)under coal power plant flue gas supplement.展开更多
This paper takes the specific characteristics of pulverized coal room in thermal power plant as the starting point,firstly,this paper analyzes the process layout and structure selection,and then the structural design ...This paper takes the specific characteristics of pulverized coal room in thermal power plant as the starting point,firstly,this paper analyzes the process layout and structure selection,and then the structural design and vibration design requirements of coal crusher house are introduced in this paper.Finally,based on the engineering example,a new structure form of vibration isolation design is creatively proposed,which provides a new design idea for the practical engineering design.展开更多
文摘Focusing on the phenomenon of gypsum rain while wet desulphurization(WFGD) were adopted in coal fired power plant without GGH, the paper studied and put forward the solutions : (1) desulfurization facilities related equipment modification;(2) optimal operation of existing desulfurization facilities.
基金funded by the National Natural Science Foundation of China(52006079)the Natural Science Foundation of Hubei Province(2020CFB247)the National Key Research and Development Program of China(2018YFB0605201)。
文摘On-site measurements of volatile organic compounds(VOCs)in different streams of flue gas were carried out on a real coal-fired power plant using sampling bags and SUMMA canisters to collect gas samples,filters to collect particle samples.Gas chromatography-flame ionization detector/mass spectrometry and gas chromatography-mass spectrometry was the offline analysis method.We found that the total mass concentration of the tested 102 VOC species at the outlet of wet flue gas desulfuration device was(13456±47)μg·m^(-3),which contained aliphatic hydrocarbons(57.9%),aromatic hydrocarbons(26.8%),halogen-containing species(14.5%),and a small amount of oxygen-containing and nitrogencontaining species.The most abundant species were 1-hexene,n-hexane and 2-methylpentane.The top ten species in terms of mass fraction(with a total mass fraction of 75.3%)were mainly hydrocarbons with a carbon number of 6 or higher and halogenated hydrocarbons with a lower carbon number.The mass concentration of VOC species in the particle phase was significantly lower than that in the gas phase.The change of VOC mass concentrations along the air pollution control devices indicates that conventional pollutant control equipment had a limited effect on VOC reduction.Ozone formation potential calculations showed that aromatic hydrocarbons contributed the highest ozone formation(46.4%)due to their relatively high mass concentrations and MIR(maximum increment reactivity)values.
基金supported by the National Nature Science Foundation of China(Grant No.51821004)supported by National Soft Science Projects:"Frontier tracking research on science and technology in the field of energy" program
文摘The development of electrical engineering and electronic, communications, smart power grid, and ultra-high voltage transmission technologies have driven the energy system revolution to the next generation: the energy internet. Progressive penetration of intermittent renewable energy sources into the energy system has led to unprecedented challenges to the currently wide use of coal-fired power generation technologies. Here, the applications and prospects of advanced coal-fired power generation technologies are analyzed. These technologies can be summarized into three categories:(1) large-scale and higher parameters coal-fired power generation technologies, including 620/650/700 oC ultra-supercritical thermal power and double reheat ultra-supercritical coal-fired power generation technologies;(2) system innovation and specific, highefficiency thermal cycles, which consist of renewable energy-aided coal-fired power generation technologies, a supercritical CO_2 Brayton cycle for coal-fired power plants, large-scale air-cooling coal-fired power plant technologies, and innovative layouts for waste heat utilization and enhanced energy cascade utilization;(3) coal-fired power generation combined with poly-generation technologies, which are represented by integrated gasification combined cycle(IGCC) and integrated gasification fuel cell(IGFC) technologies. Concerning the existing coal-fired power units, which are responsible for peak shaving, possible strategies for enhancing flexibility and operational stability are discussed. Furthermore, future trends for coal-fired power plants coupled with cyber-physical system(CPS) technologies are introduced. The development of advanced, coal-fired power generation technologies demonstrates the progress of science and is suitable for the sustainable development of human society.
文摘Nowadays, the worsening environmental issue caused by CO2 emission is greatly aggravated by human activity. Many CO2 reduction technologies are under fast development. Among these, monoethanolamine (MEA) based CO2 capture technology has been paid great attention. However, when connecting the CO2 capture process with a coal-fired power plant, the huge energy and efficiency penalty caused by CO2 capture has become a serious problem for its application. Thus, it is of great significance to reduce the related energy consumption. Based on an existing coal-fired power plant, this paper proposes a new way for the decarburized retrofitting of the coal-fired power plant, which helps to improve the overall efficiency of the power plant with less energy and efficiency penalty. The decarburized retrofitting scheme proposed will provide a new route for the CO2 capture process in China.
文摘Steam is the typical working fluid to drive turbo-generators in coal-fired power plants. It is an effective working fluid, but some of its energy is extracted in an unusable form when condensed. A Power Recovery Cycle (PRC) using a more volatile Secondary Working Fluid (SWF) added to the steam cycle could improve energy efficiency. PRCs have been applied to the flue gas and for combined cycle systems but not to traditional plant steam cycles. This paper details an analysis of adding a steam cycle PRC to a 500 MW lignite coal-fired power plant. A validated model of the plant was developed and PRCs using the three most attractive SWFs, benzene, methanol and hydrazine, were then added to the model. Adding a benzene, methanol, or hydrazine steam cycle PRC will produce an additional 59, 34, and 49 MW, respectively. An AACE Class 4 factored broad capital cost estimate and comparable operating costs and revenue estimates were developed to evaluate PRC feasibility. The benzene, methanol, and hydrazine processes had 2019 Net Present Values (NPVs) @12% of -$32, -$59, and +$35 million ± 40%, respectively. Thus, a PRC may be profitable at current or modest increases to U.S. Upper Midwest electricity prices of around $0.0667/kWh.
文摘With a particular reference to China Huaneng Group's practices in CO_2 capture, this article presents a brief ing on the current development of CO_2 capture technologies in coal-fired power plants both in China and abroad. Sooner or later, the integration of CO_2 capture and storage (CCS) facility with coal-fired power plant will be inevitably put on the agenda of developers.
文摘According to statistics, the average dust collection efficiency of flue gas emission in the large and medium- sized power plants in Zhejiang Province at present has attained higher than 97% which surpasses the 95% standard as stipulated by the Ministry of Electric Power. The dust collection efficiency of the Beilungang Power Plant has already attained 99.92%. In recent years, Zhejiang Electric Power Corporation has stipulated that all the newly constructed generating units shall be equipped with high efficiency electrostatic precipitator (ESP) while the existing power plants shall speed up their renovation work for their dust collectors. In combination with the fourth stage project of the Taizhou Power Plant, the improvement work of the dust
文摘Based on the Chinese thermal coal and power generation data,such as ultimate analysis,proximate analysis,low heat value(LHV)on as received basis,power generation volume,thermal coal consumption volume and net coal consumption rate,several mathematical models for calculating CO 2 reduction by Chinese coal-fired power plants are established.Calculations of the CO 2 emission factor(CEF),the CO 2 emission volume and reduction volume are made according to these models.The calculation results reveal that between 1993 and 2010,the CO 2 emission volume reached 31.069 Gt,reduced by 0.439 Gt,averaging 28.83 Mt each year.
文摘The physical,chemical and mineral facies properties of the flyash from Xiezhuang Coal Refuse Fired Power Plant have been studied by means of naked eyes,microscope,chemical composition analysis and XRD analysis,and compared with that of the flyash from Taian Coal Fired Power Plant.The result shows that the flyash from coal refuse fired power plant is of better quality in making construction items,for being brighter in color,fine and high activity.Some ways of comprehensive utilization of the ash have been suggested in this paper.
文摘Dry deposition samples were collected in a weekly basis during 2010 in a site located at the Mexican Pacific Coast: Manzanillo, Colima. Samples were collected with an automatic wet/dry deposition sampler using nylon filters as surrogate surfaces. Samples were extracted with deionized water and analyzed for pH, conductivity, Na+, K+, Ca2+, Mg2+, NH4-, NO3-, SO42- and Cl-. Nitrate and sulfate were the most abundant ions, contributing with 53% to the total ionic mass;and their levels exceeded the hemispheric background concentrations proposed for marine remote sites. The influence of the power plants burning combustoleo located upwind the sampling site was completely evident. From meteorological analysis, it could be observed that the sampling site was all time under the influence of power plants as a result of the effect of breezes. However, in spite of the high levels of NO3- and SO42- found in the samples collected, pH value average was almost neutral, with 28% of samples slightly acid. Potassium was the most abundant cation and from the quantification of the neutralization effect of the main alkaline components, the prevalence role of K+ was completely evident, suggesting the influence of the mining complex Pe?a Colorada located upwind the sampling site, where amyl xanthate potassium is used as collector in tailing dams. Dry deposition fluxes were estimated for all ions measured. Nitrogen dry deposition at Manzanillo is already in the upper extreme of the threshold value reported for sensible ecosystems. On the other hand, sulfur deposition exceeded slightly the critical load value reported for some ecosystems in Europe. Even at this moment, nitrogen and sulfur deposition is not a problem, it is necessary to take steps to avoid that total deposition of these elements exceeds critical loads, considering that results reported in this study not include the wet deposition fluxes.
基金the National Key Research and Development Program of China(No.2016YFB0601001)。
文摘In order to explore the changes in the growth and protein contents of Spirulina and obtain a proper strain for the fixation of carbon dioxide(CO2 from flue gas,the strains isolated from the Spirulina farms and the strain 208 were cultured under different aeration conditions including no CO2,10%CO2 and coal power plant flue gas supplements.The physiological indexes including filament length,biomass yield and chlorophyll a,soluble protein and phycocyanin contents were determined,respectively.When cultured without CO2 supplement,the strain 4-5 exhibited the highest biomass yield(1.880 g L^(−1)and a specific growth rate(0.367 d−1.However,the specific growth rate of all strains decreased significantly when they were cultured under 10%CO2 and unfiltered coal power plant flue gas supplements.Considerable differences were noted in the performance of the experimental microalgal strains under different contemporaneous conditions.The strain 7-8 achieved the highest biomass yield(1.603 g L^(−1)and relatively high phycocyanin content(7.1%)under 10%CO2 supplement.We noted that strain 4-5 had the highest specific growth rate(0.182 d−1 and biomass yield(0.43 g L^(−1)under coal power plant flue gas supplement.Strain 6-10 displayed the highest soluble protein content(66.02%),and strain 7-8 showed the highest phycocyanin content(9.28%)under coal power plant flue gas supplement.
文摘This paper takes the specific characteristics of pulverized coal room in thermal power plant as the starting point,firstly,this paper analyzes the process layout and structure selection,and then the structural design and vibration design requirements of coal crusher house are introduced in this paper.Finally,based on the engineering example,a new structure form of vibration isolation design is creatively proposed,which provides a new design idea for the practical engineering design.