Purification process of coal-based coke powder as anode for Li-ion batteries

A process of purification of coal-based coke powder as anode the treatment of coke powder with dilute hydrofluoric acid solution, for Li-ion batteries was attempted. The process started with followed by united-acid-leaching using sulfuric acid and hydrochloric acid. The effects of altering the hydrofluoric acid addition, hydrofluoric acid concentration, contact time, temperature and acid type were investigated. A minimum ash content of 0.35% was obtained when proper conditions were applied. The electrochemical performance of purified coke powder shows greatly improved electrochemical performance. The as-purified coke powder presented an initial reversible capacity of 257.4 mAh/g and a retention rate of 95% after 50 cycles. The proposed purification process paves a way to prepare a promising anode material with good performance with low cost of coke powder for Li-ion batteries.

Modeling and Simulation of Production Process on Dimethyl Ether Synthesized from Coal-based Syngas by One-step Method

As a result of shortage supply of oil resources, the process for the alternative coal-based fuel, dimethyl ether （DME）, has emerged as an important process in chemical engineering field. With the laboratory experiment data about DME synthesis and separation, the production process for DME with high purity is proposed when one-step synthesis of DME in slurry bed reactor from syngas is adopted. On the basis of experimental research and process analysis, the proper unit modules and thermophysical calculation methods for the simulation process are selected. Incorporated the experimentally determined parameters of reaction dynamic model for DME synthesis, regression constants of parameters in non-random two-liquid equation （NRTL） model for binary component in DME separation system with built-in properties model, .the process flowsheet, is.developed and simulated on the Aspen Plus platform. The simulation results coincide well with data obtained in laboratory experiment. Accordingly, the accurate simulation results offer useful references to similar equipment design and process operation optimization.

Making Ferronickel from Laterite Nickel Ore by Coal-Based Self-Reduction and High Temperature Melting Process

Based on the process of coal-based self-reduction and melting separation at high temperature, it was investigated that the effect of process factors on the reduction of iron and nickel oxide, the metal yield and the nickel content in ferronickel about the laterite nickel ore, was from Philippines and contented low nickel, high iron and aluminum. The results showed that if the C/O mole ratio was not higher than 0.5 and the reduction temperature was kept as 1200°C and then increased up to 1500°C, the metal could not separate from molten slag for the A series of experiments, which were only added CaF2. However, when the C/O ratio was added up to 0.6 - 0.8, the metal could separate well from the slag, and the yields of Fe and Ni increased gradually. But the nickel content in the metal declined from 1.79% to 1.34%. When the C/O ratio increased to 1.2, and the temperature of melting products obtained at 1200°C and rose to 1550°C, the separation of metal from slag could not be realized in B group of tests, which were only added hydrated lime. However, when both of CaF2 and hydrated lime were added, the metal could separate from slag in C group. In order to increase the content of nickel in the metal, it is necessary to restrain the reduction of iron oxide. When the C/O mole ratio is 0.6, the nickel content of metal could be 1.79%, which was higher than the theoretical ratio 1.65% of Ni/(Ni + Fe) of the latcritic nickel ore, but the yield of nickle was only 71.3%.

Dendritic spine degeneration:a primary mechanism in the aging process

Recent reports suggest that aging is not solely a physiological process in living beings;instead, it should be considered a pathological process or disease(Amorim et al., 2022). Consequently, this process involves a wide range of factors, spanning from genetic to environmental factors, and even includes the gut microbiome(GM)(Mayer et al., 2022). All these processes coincide at some point in the inflammatory process, oxidative stress, and apoptosis, at different degrees in various organs and systems that constitute a living organism(Mayer et al., 2022;AguilarHernández et al., 2023).

Characterization of semi-coke generated by coal-based direct reduction process of siderite

Solid wastes derived from metallurgical industries pose a significant threat to environment. The utilization and disposal of these solid wastes are the major concern in the world. Semi-coke generated in coal-based direct reduction process of iron ore is a by-product and its suitable utilization is not available so far. In order to handle it properly, the characteristics of this by-product were comprehensively investigated. A series of analysis methods were used to demonstrate its mineral compositions, petrography and physico-chemical properties. The results reveal that the semi-coke has poor washability. The fixed carbon content of semi-coke reaches 76.11% and the gross calorific value is 28.10 MJ/kg, both of which are similar to those of traditional sinter coke breeze. Also, semi-coke ash possesses lower content of SiO2, Al2O3, S and higher content of CaO and MgO, which could improve the strength of sinter ore when partially substituting for coke breeze in sintering. Semi-coke features well-development porous structure and higher reaction activity, which predicts that the sintering speed could be elevated to some extent when employing it as a partial replacement of coke breeze, so the studies further suggest that the potential adverse effect of the high reactivity on sintering process could be weakened by adequately coarsening the semi-coke's particle size.

Prediction and optimization of flue pressure in sintering process based on SHAP

Sinter is the core raw material for blast furnaces.Flue pressure,which is an important state parameter,affects sinter quality.In this paper,flue pressure prediction and optimization were studied based on the shapley additive explanation(SHAP)to predict the flue pressure and take targeted adjustment measures.First,the sintering process data were collected and processed.A flue pressure prediction model was then constructed after comparing different feature selection methods and model algorithms using SHAP+extremely random-ized trees(ET).The prediction accuracy of the model within the error range of±0.25 kPa was 92.63%.SHAP analysis was employed to improve the interpretability of the prediction model.The effects of various sintering operation parameters on flue pressure,the relation-ship between the numerical range of key operation parameters and flue pressure,the effect of operation parameter combinations on flue pressure,and the prediction process of the flue pressure prediction model on a single sample were analyzed.A flue pressure optimization module was also constructed and analyzed when the prediction satisfied the judgment conditions.The operating parameter combination was then pushed.The flue pressure was increased by 5.87%during the verification process,achieving a good optimization effect.

An Unprecedented Efficiency with Approaching 21%Enabled by Additive‑Assisted Layer‑by‑Layer Processing in Organic Solar Cells

Recently published in Joule,Feng Liu and colleagues from Shanghai Jiaotong University reported a record-breaking 20.8%power conversion efficiency in organic solar cells(OSCs)with an interpenetrating fibril network active layer morphology,featuring a bulk p-in structure and proper vertical segregation achieved through additive-assisted layer-by-layer deposition.This optimized hierarchical gradient fibrillar morphology and optical management synergistically facilitates exciton diffusion,reduces recombination losses,and enhances light capture capability.This approach not only offers a solution to achieving high-efficiency devices but also demonstrates the potential for commercial applications of OSCs.

Processing,microstructure,and mechanical properties of wire arc additively-manufactured AZ91 magnesium alloy using cold arc process

Thin walls of an AZ91 magnesium alloy with fine equiaxed grains were fabricated via cold arc-based wire arc additive manufacturing(CA-WAAM),and the droplet transfer behaviours,microstructures,and mechanical properties were investigated.The results showed that the cold arc process reduced splashing at the moment of liquid bridge breakage and effectively shortened the droplet transfer period.The microstructures of the deposited samples exhibited layered characteristics with alternating distributions of coarse and fine grains.During layer-by-layer deposition,the β-phase precipitated and grew preferentially along grain boundaries,while the fineη-Al_(8)Mn_(5)phase was dispersed in the α-Mg matrix.The mechanical properties of the CA-WAAM deposited sample showed isotropic characteristics.The ultimate tensile strength and elongation in the building direction(BD)were 282.7 MPa and 14.2%,respectively.The microhardness values of the deposited parts were relatively uniform,with an average value of HV 69.6.

Influence of material characteristics on the failure mode and process of landslide dam

Landslide dams,as frequent natural hazards,pose significant risks to human lives,property,and ecological environments.The grading characteristics and density of dam materials play a crucial role in determining the stability of landslide dams and the potential for dam breaches.To explore the failure mechanisms and evolutionary processes of landslide dams with varying soil properties,this study conducted a series of flume experiments,considering different grain compositions and material densities.The results demonstrated that grading characteristics significantly influence landslide dam stability,affecting failure patterns,breach processes,and final breach morphologies.Fine-graded materials exhibited a sequence of surface erosion,head-cut erosion,and subsequent surface erosion during the breach process,while well-graded materials typically experienced head-cut erosion followed by surface erosion.In coarse-graded dams,the high permeability of coarse particles allowed the dam to remain stable,as inflows matched outflows.The dam breach model experiments also showed that increasing material density effectively delayed the breach and reduced peak breach flow discharge.Furthermore,higher fine particle content led to a reduction in the residual dam height and the base slope of the final breach profile,although the relationship between peak breach discharge and the content of fine and coarse particles was nonlinear.To better understand breach morphology evolution under different soil characteristics and hydraulic conditions,three key points were identified—erosion point,control point,and scouring point.This study,by examining the evolution of failure patterns,breach processes,and breach flow discharges under various grading and density conditions,offers valuable insights into the mechanisms behind landslide dam failures.

Behaviors of vanadium and chromium in coal-based direct reduction of high-chromium vanadium-bearing titanomagnetite concentrates followed by magnetic separation

The reduction behaviors of FeO·V2O3 and FeO·Cr2O3 during coal-based direct reduction have a decisive impact on the efficient utilization of high-chromium vanadium-bearing titanomagnetite concentrates. The effects of molar ratio of C to Fe n(C)/n(Fe) and temperature on the behaviors of vanadium and chromium during direct reduction and magnetic separation were investigated. The reduced samples were characterized by X-ray diffraction(XRD), scanning election microscopy(SEM) and energy dispersive spectrometry(EDS) techniques. Experimental results indicate that the recoveries of vanadium and chromium rapidly increase from 10.0% and 9.6% to 45.3% and 74.3%, respectively, as the n(C)/n(Fe) increases from 0.8 to 1.4. At n(C)/n(Fe) of 0.8, the recoveries of vanadium and chromium are always lower than 10.0% in the whole temperature range of 1100-1250 °C. However, at n(C)/n(Fe) of 1.2, the recoveries of vanadium and chromium considerably increase from 17.8% and 33.8% to 42.4% and 76.0%, respectively, as the temperature increases from 1100 °C to 1250 °C. At n(C)/n(Fe) lower than 0.8, most of the FeO·V2O3 and FeO·Cr2O3 are not reduced to carbides because of the lack of carbonaceous reductants, and the temperature has little effect on the reduction behaviors of FeO·V2O3 and FeO·Cr2O3, resulting in very low recoveries of vanadium and chromium during magnetic separation. However, at higher n(C)/n(Fe), the reduction rates of FeO·V2O3 and FeO·Cr2O3 increase significatly because of the excess amount of carbonaceous reductants. Moreover, higher temperatures largely induce the reduction of FeO·V2O3 and FeO·Cr2O3 to carbides. The newly formed carbides are then dissolved in the γ(FCC) phase, and recovered accompanied with the metallic iron during magnetic separation.

Coal-based reduction mechanism of low-grade laterite ore

A low-grade nickel laterite ore was reduced at different reduction temperatures. The morphology of metallic particles was investigated by scanning electron microscopy （SEM） and energy dispersive spectroscopy （EDS）. Experimental results indicate that the metallic nickel and iron gradually assemble and grow into larger spherical particles with increasing temperature and prolonging time. After reduction, the nickel laterite ore obviously changes into two parts of Fe-Ni metallic particles and slag matrix. An obvious relationship is found between the reduction of iron magnesium olivine and its crystal chemical properties. The nickel and iron oxides are reduced to metallic by reductant, and the lattice of olivine is destroyed. The entire reduction process is comprised of oxide reduction and metallic phase growth.

Process Simulate软件在自动化生产线安装调试课程中的应用

针对自动化生产线安装调试课程的实践教学难题提出了使用仿真软件进行虚拟装调的方案。介绍了如何使用Process Simulate软件对自动化生产线进行虚拟装调。实践证明,使用Process Simulate软件能够有效提高自动化生产线安装调试课程的实践教学效果。

基于Arduino与Processing的心率检测计设计研究

随着社会经济的高速发展,人们的物质生活也有了极大的提高,但同时也伴随着各种疾病的到来,身体健康已经成为人们普遍关注的焦点,因此,心率检测仪、血压计、血糖仪等各种家用医疗监测仪器已经逐渐融入日常生活。心脏病是人们难以预防的突发致命疾病之一,本文介绍的是一款基于Arduino【是基于易用硬件和软件的原型开源平台,包由可编程的电路板(简称微控制器),以及集成开发环境(称为Arduino IDE)的现成软件组成】Processing(开源编程语言,包括编辑器、编译器、展示器)的简易心率检测计系统,其功能实用、操作简单,可以测量心率,当超出正常心率范围时及时预警,是一款便携的实时心率测试仪。

A review of the synthesis and application of zeolites from coal-based solid wastes

Zeolite derived from coal-based solid wastes(coal gangue and coal fly ash)can overcome the environmental problems caused by coal-based solid wastes and achieve valuable utilization.In this paper,the physicochemical properties of coal gangue and coal fly ash are introduced.The mechanism and application characteristics of the pretreatment processes for zeolite synthesis from coal-based solid wastes are also introduced.The synthesis processes of coal-based solid waste zeolite and their advantages and disadvantages are summarized.Furthermore,the application characteristics of various coal-based solid waste zeolites and their common application fields are illustrated.Finally,we propose an alkaline fusion-assisted supercritical hydrothermal crystallization as an efficient method for synthesizing coal-based solid waste zeolites.In addition,more attention should be given to the recycling of alkaline waste liquid and the application of coal-based solid waste zeolites in the field of volatile organic compound adsorption removal.

Migration behaviors and kinetics of phosphorus during coal-based reduction of high-phosphorus oolitic iron ore

To understand the migration mechanisms of phosphorus(P)during coal-based reduction,a high-phosphorus oolitic iron ore was reduced by coal under various experimental conditions.The migration characteristics and kinetics of P were investigated by a field-emission electron probe microanalyzer(FE-EPMA)and using the basic principle of solid phase mass transfer,respectively.Experimental results showed that the P transferred from the slag to the metallic phase during reduction,and the migration process could be divided into three stages:phosphorus diffusing from the slag to the metallic interface,the formation of Fe P compounds at the slag metal interface and P diffusing from the slag metal interface to the metallic interior.The reduction time and temperature significantly influenced the phosphorus content of the metallic and slag phases.The P content of the metallic phase increased with increasing reduction time and temperature,while that of the slag phase gradually decreased.The P diffusion constant and activation energy were determined and a migration kinetics model of P in coal-based reduction was proposed.P diffusion in the metallic phase was the controlling step of the P migration.

In Situ Synthesis of NaY Zeolite with Coal-Based Kaolin

NaY zeolites were in-situ synthesized from coal-based kaolin via thehydrothermal method. The effects of various factors on the structure of the samples were extensivelyinvestigated. The samples were characterized by N_2 adsorption, XRD, IR and DTG-DTA methods, andthe results show that the crystallization temperature and amount of added water play an importantrole in the formation of the zeolite structure. The 4A and P zeolites are the competitive phasepresent in the resulting product. However, NaY zeolites with a higher relative crystallinity,excluding impure crystals and the well hydrothermal stability, can be synthesized from coal-basedkaolin. These zeolites possess a larger surface area and a narrow pore size distribution, and thismeans that optimization of this process might result in a commercial route to synthesize NaYzeolites from coal-based kaolin.

Study on methanol synthesis from coal-based syngas

The intrinsic kinetic models of the Langmuir-Hinshelwood type were investigated in terms of the reaction rates of CO hydrogenation and CO_2 hydrogenation in theform of reactant fugacity. The parameters were estimated by the Universal Global Optimization using the Marquardt method. Residual error distribution and statistic tests show thatthe intrinsic kinetic models are reliable and acceptable. The mathematic model of a combined converter formed by gas-cooled and water-cooled reactor was developed and thegas-cooled reactor and the water-cooled reactor were characterized with one-dimensionalmathematic model. The distributions of temperature and concentration in the catalytic bedof the gas-cooled reactor and the water-cooled reactor in a combined converter with ayield of 1.2 Mt/a were simulated. The parallel cross linking pore model was used to describe the transfer process of multi-component diffusion system in the catalyst. The calculated value computed by the internal diffusion efficiency factor calculation model established for methanol synthesis catalyst fit the experimental value very well.

Adsorption and Regeneration of Volatile Organic Compounds(VOCs)on Coal-Based Activated Carbon by Ferric Nitrate Modification

In this study,the Heishan coal was used to prepare a series of activated carbon(AC)samples via a vapor deposition method.The effects of the Fe(NO_(3))3/coal weight ratio on the physicochemical properties of the activated carbon were systematically investigated,and the AC samples were analyzed by the N2 adsorption-desorption technique,the scanning electron microscopy,the X-ray diffraction,the Raman spectroscopy,and the Fourier transform infrared spectroscopy.Furthermore,the adsorption properties of ethyl acetate were investigated.The results indicated that as the Fe(NO_(3))3/coal mass ratio increased from 1:8 to 1:2,the specific surface area,the total pore volume and the micropore volume initially increased and then decreased.The specific surface area increased from 560.86 m^(2)/g to 685.90 m^(2)/g,and then decreased to 299.56 m^(2)/g.The total pore volume and micropore volume increased from 0.29 cm^(3)/g and 0.17 cm^(3)/g to 0.30 cm^(3)/g and 0.22 cm^(3)/g,and then decreased to 0.16 cm^(3)/g and 0.10 cm^(3)/g,respectively.The optimized ratio was 1:8.During the activation process,iron ions infiltrated the activated carbon to promote the development of the pore structure,the pore size of which was between 2.5 nm and 3 nm in daimeter.This approach could enhance the capacity for adsorption of ethyl acetate.It is worth noting that the ACs displaying the largest specific surface area and total pore volume(685.90 m^(2)/g and 0.30 cm^(3)/g)were formed under the optimized activation conditions(950℃,20%(volume)of CO_(2),ratio 1:5),and the maximum AC capacity for adsorption of ethyl acetate was 962.62 mg/g.After seven repeated thermal regeneration experiments,the saturated AC adsorption capacity was still above 90%.

Effect of reducing agents on reducing atmosphere in coal-based direct reduction of beach titanomagnetite

Beach titanomagnetite(TTM)provides a cheap alternative source of Fe and Ti,but this ore is difficult to process to make suitable concentrates for the blast furnace.Recently studies showed that it is feasible to separate Fe and Ti by coal-based direct reduction.In this study,beach TTM was selected as the research object,the effects of reducing agents on reducing atmosphere in coal-based direct reduction of beach TTM were analyzed,and the role of volatiles was also studied.The results showed that when bitumite and coke were used as reducing agents of TTM,the CO produced from volatiles was involved in the reduction reaction,and the generated CO_(2) provided the raw material for the reaction of TTM.The reduction effect of bitumite was better than that of coke.The reason is that bitumite+TTM had a higher gas generation rate and produced a higher CO partial pressure,while coke+TTM had a lower gas generation rate and produced a lower CO partial pressure.When graphite was used as a reducing agent,there was a solid-solid reaction in the early stage in the reaction.With the continuous accumulation of CO_(2),the Boudouad reaction started and accelerated.Graphite+TTM also produced a higher CO partial pressure.

Role of Ni(NO_3)_2 in the preparation of a magnetic coal-based activated carbon

The role of Nil（NO3）2 in the preparation of a magnetic activated carbon is reported in this paper. Magnetic coal-based activated carbons （MCAC） were prepared from Taixi anthracite with low ash content in the presence of Ni（NO3）2. The MCAC materials were characterized by a vibrating sample magnetometer （VSM）, X-ray diffraction （XRD）, a scanning electric microscope （SEM）, and by N2 adsorption. The cylindri- cal precursors and derived char were also subjected to thermogravimetric analysis to compare their behavior of weight losses during carbonization. The results show that MCAC has a larger surface area （1074 m21g） and a higher pore volume （0.5792 cm3/g） with enhanced mesopore ratio （by about 10~）. It also has a high saturation magnetization （1.6749 emu/g） and low coercivity （43.26 Oe）, which allows the material to be magnetically separated. The MCAC is easily magnetized because the nickel salt is con- vetted into Ni during carbonization and activation. Metallic Ni has a strong magnetism on account of electrostatic interaction. Added Ni（NO3）2 catalyzes the carbonization and activation process by accelerat- ing burn off of the carbon, which contributes to the development of mesopores and macropores in the activated carbon.