Energy evolution and structural health monitoring of coal under different failure modes:An experimental study

Structural instability in underground engineering,especially in coal-rock structures,poses significant safety risks.Thus,the development of an accurate monitoring method for the health of coal-rock bodies is crucial.The focus of this work is on understanding energy evolution patterns in coal-rock bodies under complex conditions by using shear,splitting,and uniaxial compression tests.We examine the changes in energy parameters during various loading stages and the effects of various failure modes,resulting in an innovative energy dissipation-based health evaluation technique for coal.Key results show that coal bodies go through transitions between strain hardening and softening mechanisms during loading,indicated by fluctuations in elastic energy and dissipation energy density.For tensile failure,the energy profile of coal shows a pattern of “high dissipation and low accumulation” before peak stress.On the other hand,shear failure is described by “high accumulation and low dissipation” in energy trends.Different failure modes correlate with an accelerated increase in the dissipation energy before destabilization,and a significant positive correlation is present between the energy dissipation rate and the stress state of the coal samples.A novel mathematical and statistical approach is developed,establishing a dissipation energy anomaly index,W,which categorizes the structural health of coal into different danger levels.This method provides a quantitative standard for early warning systems and is adaptable for monitoring structural health in complex underground engineering environments,contributing to the development of structural health monitoring technology.

Fault Identification for Shear-Type Structures Using Low-Frequency Vibration Modes

Shear-type structures are common structural forms in industrial and civil buildings,such as concrete and steel frame structures.Fault diagnosis of shear-type structures is an important topic to ensure the normal use of structures.The main drawback of existing damage assessment methods is that they require accurate structural finite element models for damage assessment.However,for many shear-type structures,it is difficult to obtain accurate FEM.In order to avoid finite elementmodeling,amodel-freemethod for diagnosing shear structure defects is developed in this paper.This method only needs to measure a few low-order vibration modes of the structure.The proposed defect diagnosis method is divided into two stages.In the first stage,the location of defects in the structure is determined based on the difference between the virtual displacements derived from the dynamic flexibility matrices before and after damage.In the second stage,damage severity is evaluated based on an improved frequency sensitivity equation.Themain innovations of this method lie in two aspects.The first innovation is the development of a virtual displacement difference method for determining the location of damage in the shear structure.The second is to improve the existing frequency sensitivity equation to calculate the damage degree without constructing the finite elementmodel.Thismethod has been verified on a numerical example of a 22-story shear frame structure and an experimental example of a three-story steel shear structure.Based on numerical analysis and experimental data validation,it is shown that this method only needs to use the low-order modes of structural vibration to diagnose the defect location and damage degree,and does not require finite element modeling.The proposed method should be a very simple and practical defect diagnosis technique in engineering practice.

Experimental study of the effects of a multistage pore-throat structure on the seepage characteristics of sandstones in the Beibuwan Basin:Insights into the flooding mode

To investigate the relationship between grain sizes, seepage capacity, and oil-displacement efficiency in the Liushagang Formation of the Beibuwan Basin, this study identifies the multistage pore-throat structure as a crucial factor through a comparison of oil displacement in microscopic pore-throat experiments. The two-phase flow evaluation method based on the Li-Horne model is utilized to effectively characterize and quantify the seepage characteristics of different reservoirs, closely relating them to the distribution of microscopic pores and throats. It is observed that conglomerate sandstones at different stages exhibit significant heterogeneity and noticeable differences in seepage capacity, highlighting the crucial role played by certain large pore throats in determining seepage capacity and oil displacement efficiency. Furthermore, it was found that the displacement effects of conglomeratic sandstones with strong heterogeneity were inferior to those of conventional homogeneous sandstone, as evidenced by multiple displacement experiments conducted on core samples with varying granularities and flooding systems. Subsequently, core-based experiments on associated gas flooding after water flooding were conducted to address the challenge of achieving satisfactory results in a single displacement mode for reservoirs with significant heterogeneity. The results indicate that the oil recovery rates for associated gas flooding after water flooding increased by 7.3%-16.4% compared with water flooding alone at a gas-oil ratio of approximately 7000 m^(3)/m^(3). Therefore, considering the advantages of gas flooding in terms of seepage capacity, oil exchange ratio, and the potential for two-phase production, gas flooding is recommended as an energy supplement mode for homogeneous reservoirs in the presence of sufficient gas source and appropriate tectonic angle. On the other hand, associated gas flooding after water flooding is suggested to achieve a more favorable development effect compared to a single mode of energy supplementation for strongly heterogeneous sandstone reservoirs.

Structural design and modal behaviors analysis of a new swept baffled inflatable wing

Inflatable wing has significant application value in the design of loitering munitions because of its advantages such as lightweight and foldability.However,due to the flexible characteristics,aeroelastic behaviors of inflatable wings such as flutter are nonnegligible in flight.By designing a certain angle between the inflatable beam and the wing span,the structural dynamic and even the aeroelastic performance of the inflatable wing can be effectively improved.Based on the analysis of the mechanical and geometric characteristics of the inflatable structure,a new inflatable wing with sweep arranged inflatable beams is proposed,and the main design variables and methods are analyzed.For purpose of investigating the aeroelastic performance of the swept baffled inflatable wing,the modal behaviors by considering the wet mode are studied.In consideration of the deficiencies of the traditional wet modal analysis method,by introducing the influence on the additional stiffness of flow field,an added massstiffness method is proposed in this paper,and the advantages are verified by ground vibration experiments.On this basis,the effects of baffles sweep angle,pressure,and boundary conditions on the modal parameters and aeroelastic performance of inflatable wing are analyzed.The results show that the aeroelastic performance of the inflatable wing can be designed by changing the baffles sweep angle,which is enlightened for the aeroelastic tailoring design on inflatable wings.

Boundary Element Analysis forModeⅢCrack Problems of Thin-Walled Structures from Micro-to Nano-Scales

This paper develops a new numerical framework for modeⅢcrack problems of thin-walled structures by integrating multiple advanced techniques in the boundary element literature.The details of special crack-tip elements for displacement and stress are derived.An exponential transformation technique is introduced to accurately calculate the nearly singular integral,which is the key task of the boundary element simulation of thin-walled structures.Three numerical experiments with different types of cracks are provided to verify the performance of the present numerical framework.Numerical results demonstrate that the present scheme is valid for modeⅢcrack problems of thin-walled structures with the thickness-to-length ratio in the microscale,even nanoscale,regime.

Assessment of structural stability in Bohai Sea area based on AHP-GDM model

The AHP-GDM model is used for the assessment of structural stability, with the Bohai Sea area as an exam- ple. In this model, the credit degree of each expert is calculated through the assessment matrix based on the similarity and diversity of vector. The comprehensive opinions of expert panel are quantitatively obtained by considering the effect ofcredit degree. According to the geological structural setting, the Bohai Sea is di- vided into twelve assessment zones of structural stability by non-uniform element method. The structural stability grade of each zone is obtained on the basis of the latest geophysical data, earthquake statistical data, and the information of fault activities, current stress field and crustal deformation. The results show that there are one relatively stable area, three relatively sub-stable areas, six relatively sub-unstable areas and two relatively unstable areas. The assessment results of non-uniform element method are very close with those of uniform grid method with size of 0.25 in longitude direction and 0.14 in latitude direction. However the workload of non-uniform element method is only 1 / 16 of the latter. Compared with traditional assessment methods of structural stability, a more objective and reliable assessment result can be obtained by combining non-uniform element method and AHP-GDM model.

System Reliability Analysis for Truss Structures Based on Automatic Updated Model

Multiple failure modes tend to be identified in the reliability analysis of a redundant truss structure.This identification process involves updating the model for identifying the next potential failure members.Herein we intend to update the finite element model automatically in the identification process of failure modes and further perform the system reliability analysis efficiently.This study presents a framework that is implemented through the joint simulation of MATLAB and APDL and consists of three parts:reliability index of a single member,identification of dominant failure modes,and system-level reliability analysis for system reliability analysis of truss structures.Firstly,RSM(response surface method)combines with a constrained optimization model to calculate the reliability indices ofmembers.Then theβ-unzipping method is adopted to identify the dominant failuremodes,and the system function in MATLAB,as well as the EKILL command in APDL,is used to facilitate the automatic update of the finite element model and realize load-redistribution.Besides,the differential equivalence recursion algorithmis performed to approximate the reliability indices of failuremodes efficiently and accurately.Eventually,the PNET(probabilistic network evaluation technique)is used to calculate the joint failure probability as well as the system reliability index.Two illustrative examples demonstrate the accuracy and efficiency of the proposed system reliability analysis framework through comparison with corresponding references.

Short beam shear properties and failure modes of the wood-based X-type lattice sandwich structure

A wood-based X-type lattice sandwich structure was manufactured by insertion-glue method.The birch was used as core,and Oriented Strand Board was used as panel of the sandwich structure.The short beam shear properties and the failure modes of the wood-based X-type lattice sandwich structure with different core direction(vertical and parallel),unit specification(120 mm×60 mm and 60 mm×60 mm),core size(50 mm and 60 mm),and drilling depth(9 mm and 12 mm)were investigated by a short beam shear test and the establishment of a theoretical model to study the equivalent shear modulus and deflection response of the X-type lattice sandwich structure.Results from the short beam shear test and the theoretical model showed that the failure modes of the wood-based X-type lattice sandwich structure were mainly the wrinkling and crushing of the panels under three-point bending load.The experimental values of deflection response of various type specimens were higher than the theoretical values of them.For the core direction of parallel,the smaller the unit specification is,the shorter the core size is,and the deeper the drilling depth is,the greater the short beam shear properties of the wood-based X-type lattice sandwich structure is.

Finite Element Model Updating for Structural Health Monitoring

This paper provides a model updating approach to detect,locate,and char-acterize damage in structural and mechanical systems by examining changes in mea-sured vibration responses.Research in vibration-based damage identification has been rapidly expanding over the last few decades.The basic idea behind this technology is that modal parameters(notably frequencies,mode shapes,and modal damping)are functions of the physical properties of the structure(mass,damping,and sifies).Therefore,changes in the physical properties will cause changes in the modal proper-ties which could be obtained by structural health monitoring(SHM).Updating is a process fraught with numerical difficulties.These arise from inaccuracy in the model and imprecision and lack of information in the measurements,mainly taken place in joints and critical points.The motivation for the development of this technology is.presented,methods are categorized according to various criteria such as the level of damage detection provided from vibration testing,natural frequency and mode shape readings are then obtained by using modal analysis techniques,which are used for updating structural parameters of the associated finite element model The experi-mental studies for the laboratory tested bridge model show that the proposed model.updating using ME scope technique can provide reasonable model updating results.

A novel multi-channel porous structure facilitating mass transport towards highly efficient alkaline water electrolysis

An advantageous porous architecture of electrodes is pivotal in significantly enhancing alkaline water electrolysis(AWE)efficiency by optimizing the mass transport mechanisms.This effect becomes even more pronounced when aiming to achieve elevated current densities.Herein,we employed a rapid and scalable laser texturing process to craft novel multi-channel porous electrodes.Particularly,the obtained electrodes exhibit the lowest Tafel slope of 79 mV dec^(-1)(HER)and 49 mV dec^(-1)(OER).As anticipated,the alkaline electrolyzer(AEL)cell incorporating multi-channel porous electrodes(NP-LT30)exhibited a remarkable improvement in cell efficiency,with voltage drops(from 2.28 to 1.97 V)exceeding 300 mV under 1 A cm^(-1),compared to conventional perforated Ni plate electrodes.This enhancement mainly stemmed from the employed multi-channel porous structure,facilitating mass transport and bubble dynamics through an innovative convection mode,surpassing the traditional convection mode.Furthermore,the NP-LT30-based AEL cell demonstrated exceptional durability for 300 h under 1.0 A cm^(-2).This study underscores the capability of the novel multi-channel porous electrodes to expedite mass transport in practical AWE applications.

LINEAR ACTIVE STRUCTURES AND MODES (Ⅰ) —BASIC CONCEPTS AND PROPERTIES

Some basic concepts about the active structures were firstly explained, and the main subjects to study in the field of active structure dynamics were synthesized. For the linear active structures, the annotations on the modes were done in detail. The physical meanings of the right and left eigenvectors were explained. The right eigenvectors are the modal shapes and the modal responses of an active structure depend on the left ones. The adjoint structure of an active structure was defined and the reciprocity theorem was interpreted. For two active structures, which are adjoint to each other and with the reciprocal gain-matrices, the right and left eigenvector are reciprocal. The relationship between an active structure and the corresponding passive structure is expressed with the transfer functions, which is employed to resolve the estimation problems.

The relation between modes of lithologic association and interlayer-gliding structures in coal mine

As a case study of the Panji No.1 Coal Mine in Anhui Province, based on thesite measured and statistical data, summarized the lithologic associations, characteristicsand distribution laws of interlayer-gliding structures and tectonic coal in the No.11-2 coalseams.The results show that 9 modes of lithologic association can form interlayer-glidingstructures.It is more easy for rock slip to occur when the lithologic associations are mainroof + coal seam + immediate floor type, compound roof+immediate roof + coal seam +immediate floor type and immediate roof + coal seam + immediate floor type.Lithologicassociations of roof and floor are the precondition to the formation of interlayer-glidingstructures.

Tunable Reflection Bands and Defect Modes in One-Dimensional Tilted Photonic Crystal Structure

We show theoretically that range of reflection bands and defect modes inside the band gap can be tuned by using a one-dimensional tilted photonic crystal (TPC) structure. A TPC structure is similar to the conventional PC structure with the only difference that in this case alternate layers are inclined at certain angle in the direction of periodicity of the structure. In order to obtain the reflectance spectra of the proposed structure transfer matrix method (TMM) has been employed. From the analysis of the reflectance curve, it is found that 100% reflectance range can be varied and enhanced by using TPC structure for both (TE- and TM-) polarizations. The enhancement in reflection bands increases as the tilt angle increases for both the polarizations and hence the enlarged omni-reflectance bands are obtained. Further, we study the properties of the defect modes in TPC structure by introducing the tilted defect at the different tilt angle. The results show that defect modes (tunneling modes) can be tuned at different wavelengths by changing the tilt angle of the structure without changing other parameters. Finally, the effect of variation thickness of defect layers on the tunneling mode has been studied for both TPC and conventional PC structure. The proposed model might be used as a tunable broadband omnidirectional reflector as well as tunable tunneling or transmission mode, which has potential applications in the field of photonics and optoelectronics.

LINEAR ACTIVE STRUCTURES AND MODES (Ⅱ) —DISCRETE SYSTEMS AND BEAMS

The basic concepts about the active structures and some attributes of the modes were presented in paper “Liner Active Structures and Modes]( I) ". The characteristics of the active discrete systems and active beams were discussed, especially, the stability of the active structures and the orthogonality of the eigenvectors. The notes about modes were portrayed by a model of a seven-storeyed building with sensors and actuators. The concept of the adjoint active structure was extended from the discrete systems to the beams that were the representations of the continuous structures. Two types of beams with different placements of the measuring and actuating systems were discussed in detail. One is the beam with the discrete sensors and actuators, and the other is the beam with distributed sensor and actuator function. The orthogonality conditions were derived with the modal shapes of the active beam and its adjoint active beam. An example shows that the variation of eigenvalues with feedback amplitude for the homo-configuration and non-homo-configuration active structures.

Coalfield structure and structural controls on coal in China

The occurrence of coal-bearing strata in a variety of coal-bearing basins of China is characterized by late tectonic deformation and remarkable spatial and geochronologic differences.The main controlling factors,which determine the tectonic framework of coalfields,include the geodynamic environment,tectonic evolution,deep structures,tectonic stress,and lithologic combination of the coal measures.The Chinese continent has experienced multi-stage tectonic movements since the Late Paleozoic.The spatial and temporal heterogeneity of its continental tectonic evolution,the complexity of its basement properties,and its stratigraphic configurations control the tectonic framework of its coalfields’present complex and orderly patterns.The concept of coal occurrence structural units is proposed in this paper and is defined as the structural zoning of coal occurrence.China’s coalfields are divided into five coal occurrence structural areas,and the structural characteristics of the coalfields in five main coal occurrence areas throughout the country are summarized.Based on the analysis of the relationship between the structure characteristics and occurrence of coal in these coalfields,the coal-controlling structures are divided into six groups:extensional structural styles,compressional structural styles,shearing and rotational structural styles,inverted structural styles,sliding structural styles,and syn-depositional structural styles.In addition,the distribution of coal-controlling structural styles is briefly summarized in this paper.

Comparison of the hygrothermal performance of two light-framed timber structure buildings under different operation modes

Light-framed timber structure(LTS)buildings have been highly valued in recent years due to their low-carbon characteristics.However,the applicability of the building envelope is closely related to indoor and outdoor conditions.The hot summer and cold winter(HSCW)climate zone in China has high humidity and great temperature variation throughout the year,resulting in distinct outdoor environments in different seasons.The indoor environment is greatly affected by energy-consumption patterns and window-opening habits,which largely depend upon the regulation operations of occupants.All these interrelated factors lead to extremely complex boundary conditions on each side of the building envelope.Whether the structures of LTS buildings are applicable in this climate zone,therefore,needs to be carefully considered.In this study,two LTS buildings with different envelopes were established in Haining,China,situated in the HSCW climate zone,and selected as the study objects.Different operation modes were adopted to create a variety of indoor environments.Under each condition,the processes of heat and moisture transfer within the building envelopes and the indoor environment were monitored and compared.The comparison indicated that the building envelope with high moisture storage and insulation ability maintained a relatively stable indoor environment,especially when the environment changed abruptly.Conversely,if the outdoor environment was equable(e.g.,relative humidity within the range of 30%–60%)or intermittent energy consumption modes were adopted,the building envelope with a low thermal inertia index and weak moisture-buffering ability performed better because it enabled a faster response of the indoor environment to air conditioning.Moreover,a high risk of moisture accumulation between the thermal insulation layer and other materials with a large water vapour transfer resistance factor was also identified,suggesting a higher requirement for the vapour insulation of the envelopes of LTS buildings.

Sliding Mode Variable Structure Control for Visual Servoing System

A visual servoing tracking controller is proposed based on the sliding mode control theory in order to achieve strong robustness against parameter variations and external disturbances. A sliding plane with time delay compensation is presented by the pre-estimate of states. To reduce the chattering of the sliding mode controller, a modified exponential reaching law and hyperbolic tangent function are applied to the design of visual controller and robot joint controller. Simulation results show that the visual servoing control scheme is robust and has good tracking performance.

Variable structure control with sliding mode prediction for discrete-time nonlinear systems

A new variable structure control algorithm based on sliding mode prediction for a class of discrete-time nonlinear systems is presented. By employing a special model to predict future sliding mode value, and combining feedback correction and receding horizon optimization methods which are extensively applied on predictive control strategy, a discrete-time variable structure control law is constructed. The closed-loop systems are proved to have robustness to uncertainties with unspecified boundaries. Numerical simulation and pendulum experiment results illustrate that the closed-loop systems possess desired performance, such as strong robustness, fast convergence and chattering elimination.

Research on mode localization of reticulated shell structures

Reticulated shell structures （RSSs） are characterized as cyclically periodic structures. Mistuning of RSSs will induce structural mode localization. Mode localization has the following two features： some modal vectors of the structure change remarkably when the values of its physical parameters （mass or stiffness） have a slight change; and the vibration of some modes is mainly restricted in some local areas of the structure. In this paper, two quantitative assessment indexes are introduced that correspond to these two features. The first feature is studied through a numerical example of a RSS, and its induced causes are analyzed by using the perturbation theory. The analysis showed that internally, mode localization is closely related to structural frequencies and externally, slight changes of the physical parameters of the structure cause instability to the RSS. A scaled model experiment to examine mode localization was carried out on a Kiewit single-layer spherical RSS, and both features of mode localization are studied. Eight tests that measured the changes of the physical parameters were carried out in the experiment. Since many modes make their contribution in structural dynamic response, six strong vibration modes were tested at random in the experimental analysis. The change and localization of the six modes are analyzed for each test. The results show that slight changes to the physical parameters are likely to induce remarkable changes and localization of some modal vectors in the RSSs.