Analysis of Coating Microstructure of Hot-Dip Aluminum of Deformed Low-Carbon Steel Containing Rare Earth

The coating microstructure of hot-dip aluminum (HDA) of deformed low-carbon steel containing RE was analyzed by metallography microscopy, TEM and XRD, and the forming mechanism was also discussed. The results show that, the Fe_2Al_5 phase, on whose subcrystal boundaries, Al particles with the size of 7～30 μm existing on parallel linear are, grows a strong orientation. And the spread activation energy of Al is 155.22 kJ·mol -1. In addition, the effects of deformation on coating microstructure of hot-dip aluminum and the function of RE were preliminarily analyzed.

EFFECT OF MICROSTRUCTURE OF ALUMINIDE COATING ON HIGH-CYCLE FATIGUE PERFORMANCE OF COATING-SUPERALLOY SYSTEM

The high-cycle fatigue performance of different microstructures of aluminide coating- superalloy system has been studied at 900℃.The single phase coating of coarse equiaxial grain NiAI(β)has unfavorable eJfect onJatigue life of the coating-superalloy.The fatigue life may shorten if the coating of NiAl(β)was an enrichment of coarse refractory metal grains. While an improvement can be made by dispersing numerous secondary phase particles such as extreme.fine γ′,quasi-σ-phase and others.

Influence of Laser Coating on Microstructure and Properties of an Al-Si Alloy

The microstructure and wear resistance of a cast Al-Si alloy coated with metal and rare earth elements and treated by the laser rapid melt-solidification(LRMS)are studied in the pres- ent work.Optical and SEM micrographic analyses showed that a superfine microstructure was ob- tained,and the hardness was remarkably enhanced by the LRMS treatment.Wear test showed that the rapid melt-solidified microstructure had higher wear resistance than that treated by ordinary solid solution treatment.

Microstructure characteristics of Ni/WC composite cladding coatings

A multilayer tungsten carbide particle（WCp）-reinforced Ni-based alloy coating was fabricated on a steel substrate using vacuum cladding technology.The morphology,microstructure,and formation mechanism of the coating were studied and discussed in different zones.The microstructure morphology and phase composition were investigated by scanning electron microscopy,optical microscopy,X-ray diffraction,and energy-dispersive X-ray spectroscopy.In the results,the coating presents a dense and homogeneous microstructure with few pores and is free from cracks.The whole coating shows a multilayer structure,including composite,transition,fusion,and diffusion-affected layers.Metallurgical bonding was achieved between the coating and substrate because of the formation of the fusion and diffusion-affected layers.The Ni-based alloy is mainly composed of y-Ni solid solution with finely dispersed Cr7C3/Cr（23）C6,CrB,and Ni＋Ni3Si.WC particles in the composite layer distribute evenly in areas among initial Ni-based alloying particles,forming a special three-dimensional reticular microstructure.The macrohardness of the coating is HRC 55,which is remarkably improved compared to that of the substrate.The microhardness increases gradually from the substrate to the composite zone,whereas the microhardness remains almost unchanged in the transition and composite zones.

Microstructure of Ni–Al powder and Ni–Al composite coatings prepared by twin-wire arc spraying

Ni–Al powder and Ni–Al composite coatings were fabricated by twin-wire arc spraying（TWAS）. The microstructures of Ni-5wt%Al powder and Ni-20wt%Al powder were characterized by scanning electronic microscopy（SEM） and energy dispersive spectroscopy（EDS）. The results showed that the obtained particle size ranged from 5 to 50 μm. The morphology of the Ni–Al powder showed that molten particles were composed of Ni solid solution, NiAl, Ni_3Al, Al_2O_3, and NiO. The Ni–Al phase and a small amount of Al_2O_3 particles changed the composition of the coating. The microstructures of the twin-wire-arc-sprayed Ni–Al composite coatings were characterized by SEM, EDS, X-ray diffraction（XRD）, and transmission electron microscopy（TEM）. The results showed that the main phase of the Ni-5wt%Al coating consisted of Ni solid solution and Ni Al in addition to a small amount of Al_2O_3. The main phase of the Ni-20wt%Al coating mainly consisted of Ni solid solution, Ni Al, and Ni_3Al in addition to a small amount of Al and Al_2O_3, and Ni Al and Ni_3Al intermetallic compounds effectively further improved the final wear property of the coatings. TEM analysis indicated that fine spherical NiAl_3 precipitates and a Ni–Al–O amorphous phase formed in the matrix of the Ni solid solution in the original state.

Microstructure studies of air-plasma-spray-deposited CoNiCrAlY coatings before and after thermal cyclic loading for high-temperature application

In the present study, bond-coats for thermal barrier coatings were deposited via air plasma spraying（APS） techniques onto Inconel 800 and Hastelloy C-276 alloy substrates. Scanning electron microscopy（SEM）, transmission electron microscopy（TEM）, X-ray diffraction（XRD）, and atomic force microscopy（AFM） were used to investigate the phases and microstructure of the as-sprayed, APS-deposited Co Ni Cr Al Y bond-coatings. The aim of this work was to study the suitability of the bond-coat materials for high temperature applications. Confirmation of nanoscale grains of the γ/γ′-phase was obtained by TEM, high-resolution TEM, and AFM. We concluded that these changes result from the plastic deformation of the bond-coat during the deposition, resulting in Co Ni Cr Al Y bond-coatings with excellent thermal cyclic resistance suitable for use in high-temperature applications. Cyclic oxidative stability was observed to also depend on the underlying metallic alloy substrate.

Preparation and Microstructure of a Si-Mo Fused Slurry Coating on Carbon/Carbon Composites for Oxidation Protection

A coating of composition Si-40Mo (wt pct) was prepared by fused slurry coating method on the two-dimensional carbon/carbon (2D-C/C) composite to improve oxidation resistance. In the procedure of the fabrication, pure St slurry inner layer in the pre-coating was necessary to apply because of infiltration of liquid Si into the substrate during the sintering. The coating consists of Si continuous phase and MoSi2 particles. In addition, the infiltration of Si into the substrate and the SiC reaction layer between the coating and the C/C composite were observed. Oxidation behavior of coated and uncoated C/C composites was studied in cyclic mode. The oxidation resistance and the thermal shock resistance of the Si-Mo fused slurry coating were quite excellent at 1370℃.

Microstructure and Properties of Plasma Spraying Boron Carbide Coating

Microstructure of plasma spray boron carbide coating was studied by SEM and TEM. Its physical, mechanical and electrical properties were measured. The results showed that high microhardness, modulus and low porosity of B4C coating were manufactured by plasma spray. It was lamellar packing and dense. The B4C coating examined here contained two principal structures and two impurity phase besides major phase. The relatively small value of Young's modulus, comparing with that of the bulk materials, is explained by porosity . The Fe impurity phase could account for the relatively high electrical conductivity of boron carbide coating by comparing with the general boron carbide materials.

Microstructure and Performance Analysis of Organic Coating under High Temperature and High CO_2 Partial Pressure

To evaluate the property of the organic coatings in oil and gas plants, the aging process was studied in high temperature and high CO_2 partial pressure environment. Correlations were developed between the macroscopic properties and microstructure of the organic coatings. The surface appearance, mechanical properties, and permeability of the organic coatings were measured. Furthermore, the crystal structure of the organic coatings was investigated through synchrotron radiation grazing incidence X-ray diffraction（GIXRD） on the BL14B1 beam line in Shanghai Synchrotron Radiation Facility. Combined with the Fourier transform infrared spectroscopy, the molecular structure of the organic coatings was investigated. The experimental results indicate that the thickness variation and weight loss of the organic coatings increase with the immersion time, and the penetration resistance of the coating obviously decreases as the temperature rises. Moreover, the degradation of the organic coatings with immersion time in high temperature and high CO_2 partial pressure environment is caused by the amorphization of the organic coatings as the groups and bonds of the organic coatings were not damaged.

Effect of microstructure on the mechanical, thermal, and electronic property measurement of ceramic coatings

Ceramic materials were investigated as thermal barrier coatings and electrolytes. Electrophoretic deposition（EPD） and physical vapor deposition（PVD） were employed to fabricate samples, and the mechanical properties and microstructure were examined by nanoindentation and microscopy, respectively. Yttria-stabilized zirconia/alumina（YSZ/Al2O3） composite coatings, a candidate for thermal barrier coatings, yield a kinky, rather than smooth, load–displacement curve. Scanning electron microscope（SEM） examination reveals that the kinky curve is because of the porous microstructure and cracks are caused by the compression of the indenter. Li0.34La0.51 Ti O2.94（LLTO） on Si/Sr Ru O3（Si/SRO） substrates, an ionic conductor in nature, demonstrates electronic performance. Although SEM images show a continuous and smooth microstructure, a close examination of the microstructure by transmission electron microscopy（TEM） reveals that the observed spikes indicate electronic performance. Therefore, we can conclude that ceramic coatings could serve multiple purposes but their properties are microstructure-dependent.

STUDY ON PTA CLAD (Cr,Fe)_7C_3/γ-Fe CERAMAL COMPOSITE COATING

A wear resistant （Cr, Fe）7C3/γ-Fe ceramalcomposite coating wasfabricatedon substrate of a 0.45% C carbon steel by plasma transferred arc （PTA） cladding process using the Fe-Cr-C elemental powder blends. The microstructure, microhardness and dry sliding wear resistance of the coating were evaluated. Results indicate that the plasma transferred arc clad ceramal composite coating has a rapidly solidified microstructure consisting of blocky primary （Cr, Fe）7C3 and the interblocky （ Cr, Fe）7C3/γ-Fe eutectics and is metallurgically bonded to the 0.45%C carbon steel substrate. The ceramal composite coating has high hardness and excellent wear resistance under dry sliding wear test condition.

Wear characteristics of spheroidal graphite roll WC-8Co coating produced by electro-spark deposition

Electro-spark deposition（ESD） was adopted for preparing high property coatings by depositing WC-8Co cemented carbide on an spheroidal graphite roll substrate.The microstructure and properties of the coating were investigated by X-ray diffraction（XRD）, scanning electron microscopy（SEM） with energy dispersive X-ray（EDX） and ball-disc configuration wear tester.The results show that nanosized particles and amorphous structures prevail in the coating which is metallurgically bonded to the substrate.The microstructures of the transition zone include columnar structure and equiaxed structure.The primary phases of the coating contain W2C, W6C2.54, Fe3W3C, and Co3W3C.The results of abrasive test show that the coating has low friction coefficients（μaverage = 0.18） and the wear mechanisms are mainly abrasive wear, fatigue wear, and oxidation wear.The maximum microhardness value of the coating is about 17410 N/mm2.The study reveals that the electro-spark deposition process has better coating quality and the coating has high wear resistance and hardness.

Why a mosquito leg possesses superior load-bearing capacity on water:Experimentals

Mosquitoes possess the striking ability to walk on water because each of their legs has a huge water supporting force（WSF） that is 23 times their body weight.Aiming at a full understanding of the origins of this extremely large force,in this study,we concentrate on two aspects of it：the intrinsic properties of the leg surface and the active control of the initial stepping angle of the whole leg.Using a measurement system that we developed ourselves,the WSFs for the original leg samples are compared with those whose surface wax and microstructures have been removed and with those of a different stiffness.The results show that leg f exibility plays a dominant role over surface wax and microstructures on the leg surface in creating the supporting force.Moreover,we discuss the dependence relationship between the maximum WSF and the initial stepping angle,which indicates that the mosquito can regulate this angle to increase or decrease the WSF during landing or takeoff.These finding are helpful for uncovering the locomotion mechanism of aquatic insects and for providing inspiration for the design of microfluids miniature boats,biomimetic robots,and microsensors.

Fabrication of Fe–TiC–Al_2O_3 composites on the surface of steel using a TiO_2–Al–C–Fe combustion reaction induced by gas tungsten arc cladding

The aim of the present study was to fabricate Fe-TiC-Al2O3 composites on the surface of medium carbon steel.For this purpose,TiO2-3C and 3TiO2-4Al-3C-xFe（0 ≤ x ≤ 4.6 by mole） mixtures were pre-placed on the surface of a medium carbon steel plate.The mixtures and substrate were then melted using a gas tungsten arc cladding process.The results show that the martensite forms in the layer produced by the TiO2-3C mixture.However,ferrite-Fe3C-TiC phases are the main phases in the microstructure of the clad layer produced by the 3TiO2-4Al-3C mixture.The addition of Fe to the TiO2-4Al-3C reactants with the content from 0 to 20wt%increases the volume fraction of particles,and a composite containing approximately 9vol%TiC and A12O3 particles forms.This composite substantially improves the substrate hardness.The mechanism by which Fe particles enhance the TiC ＋ A12O3 volume fraction in the composite is determined.