Tensile Mechanical Behavior of Cold Rolled Si-Mn Steel Under Different Strain Rates

Tensile mechanical behavior of cold rolled Si-Mn steel after TRIP (TRansformation Induced Plasticity) and DP (Dual Phase) treatment were investigated under different strain rates.The dynamic tensile test was carried out using the rotation disk bar-bar tensile impact apparatus.At static tension test condition,the values of total elongation for TRIP steel was approximately 2-3 times higher than DP steel because of TRIP effect;the DP steel showed a higher tensile strength because of 39.6vol% martensite in the matrix.The results of tension test at high strain rate condition were different.For the studied steel,the elongation increased with increasing strain rate due to softening of matrix caused by adiabatic heating;in addition,TRIP steel at low strain rate was always higher than that at high strain rate because progressive strain induced retained austenite was suppressed at high strain rate.

Effect of continuous annealing parameters on the mechanical properties and microstructures of a cold rolled dual phase steel

A cold rolled dual phase （DP） steel with the C-Si-Mn alloy system was trial-produced in the laboratory, utilizing a Gleeble-3800 thermal simulator. The effects of continuous annealing parameters on the mechanical properties and microstructures of the DP steel were investigated by mechanical testing and microstructure observation. The results show that soaking between 760 and 820℃ for more than 80 s, rapid cooling at the rate of more than 30℃/s from the quenching temperature between 620 and 680℃, and overaging lower than 300℃ are beneficial for the mechanical properties of DP steels. An appropriate proportion of the two phases is one of the key factors for the favorable properties of DP steels. If the volume fraction of martensite and, thereby, free dislocations are deficient, the tensile strength and n value of DP steels will decrease, whereas, the yield strength will increase. But if the volume fraction of martensite is excessive to make it become a dominant phase, the yield and tensile strength will increase, whereas, the elongation will decrease obviously. When rapid cooling rate is not fast enough, pearlite or cementite will appear, which will degrade the mechanical properties. Even though martensite is sufficient, if it is decomposed in high temperature tempering, the properties will he unsatisfied.

Controlled Rolling and Cooling Process for Low Carbon Cold Forging Steel

Effect of controlled rolling and cooling process on the mechanical properties of low carbon cold forging steel was investigated for different processing parameters of a laboratory hot rolling mill. The results show that the specimens with fast cooling after hot rolling exhibit very good mechanical properties, and the improvement of the mechanical properties can be attributed mainly to the ferrite-grain refinement. The mechanical properties increase with decreasing final cooling temperature within the range from 670 ℃ to 570 ℃ due to the finer interlamellar spacing of pearlite colony. The specimen with fast cooling after low temperature rolling shows the highest values of the mechanical properties. The effect of the ferrite grain size on the mechanical properties was greater than that of pearlite morphology in the present study. The mechanical properties of specimens by controlled rolling and cooling process without thermal treatment were greatly superior to that of the same specimens by the conventional rolling, and their tensile strength reached 490 MPa grade even in the case of low temperature rolling without controlled rolling. It might be expected to realize the substitution medium-carbon by low-carbon for 490 MPa grade cold forging steel with controlled rolling and cooling process.

Research on the properties of laser welded joints of aluminum killed cold rolled steel

Aluminum killed cold rolled steel used for automobiles was welded in this paper by using CO 2 laser with wavelength 10.6μm.The experiment shows that high quality of welding can be realized at welding speed of 4 500mm/min by optimizing the parameters.The strength and hardness of laser welded joints for aluminum killed cold rolled steel increased compared to those of the base metal while the formability decreased.Forming limit diagram of joint material indicated that the laser weld seam should avoid the maximum deformation area of automobile parts during the designing period for the position of weld seam.

Improved cold rolling workability of warm rolled Fe?6.5wt%Si electrical steel with columnar grains by annealing

The effects of annealing temperature（with the annealing time being constant at 1 h） on the microstructure, ordering, residual stress, mechanical properties, and subsequent cold rolling workability of Fe-6.5wt%Si electrical steel with columnar grains were investigated, where the steel was warm rolled at 500℃ with a reduction of 95%. The results show that recrystallization began to occur in the sample annealed at 575℃ and that full recrystallization occurred in the sample annealed at 625℃. When the annealing temperature was 500℃ or greater, the extent of reordering in the sample was high, which reduced the room-temperature plasticity. However, annealing at temperatures below 300℃ did not significantly reduce the residual tensile stress on the edge of the warm rolled samples. Considering the comprehensive effects of annealing temperature on the recrystallization, reordering, residual stress, and mechanical properties of the warm rolled Fe-6.5wt%Si electrical steel with columnar grains, the appropriate annealing temperature range is 300℃-400℃. Unlike the serious edge cracks that appeared in the sample after direct cold rolling, the annealed samples could be cold rolled to a total reduction of more than 71.4% without the formation of obvious edge cracks, and bright-surface Fe-6.5wt%Si electrical steel strips with a thickness less than 0.1 mm could be fabricated by cold rolling.

Microstructure evolution and mechanical properties of 1000 MPa cold rolled dual-phase steel

The microstructure evolution of 1 000 MPa cold rolled dual-phase (DP) steel at the initial heating stages of the continuous annealing process was analyzed. The effects of different overaging temperatures on the microstructures and mechanical properties of 1 000 MPa cold rolled DP steel were investigated using a Gleeble-3500 thermal/mechanical simulator. The experimental results show that ferrite recovery and recrystallization, pearlite dissolution and austenite nucleation and growth take place in the annealing process of ultra-high strength cold rolled DP steel. When being annealed at 800 ℃ for 80 s, the tensile strength and total elongation of DP steel can reach 1 150 MPa and 13%, respectively. The microstructure of DP steel mainly consists of a mixture of ferrite and martensite. The steel exhibits low yield strength and continuous yielding which is commonly attributed to mobile dislocations introduced during cooling process from the intercritical annealing temperature.

Effect of the Heat-treatment Temperature on the Mechanical Properties and Microstructural Evolution of Cold-rolled Twinning-induced Plasticity Steel

TWIP steels with 70% cold-rolled reduction were heated at 500, 600, 700, 800, 900, 1000, and 1100 ℃. Then, the properties before and after heating were examined through tensile and hardness experiments. The microstructures were also analyzed by optical microscopy and transmission electron microscopy. The relationship between the properties and microstructure was examined as well. Finally, the evolution process of cold-rolled microstructures during heating was discussed in detail. Moreover, some conclusions can be drawn, and the heating evolution characteristics are described.

Internal oxidation of hot-rolled ultra-high strength steel and its effect on the surface quality of cold-rolled sheets

In this study,the scale and internal oxidation of hot-rolled ultra-high strength steel sheets were characterized.It was found that both the formation of the scale and the internal oxidation of Si and Mn depended on the coiling temperature and position of the steel sample on the strip coil.At a relatively high coiling temperature,a large amount of internal oxidation was observed on the samples cut from the middle of the coil.The depth of the internal oxidation zone exceeded 10 μm and a thin iron layer covering the scale was observed in some cases.Pickling and cold-rolling experiments were conducted on selected samples.Scale pickling was found to be greatly delayed by the formation of an iron layer,which frequently resulted in under-pickled defects.In addition,pickling of the entire internal oxidation zone was difficult,except at the grain boundaries,where the degree of internal Si and Mn oxidation was enriched.The surface of the cold-rolled steel sheet was ruined by the remaining oxidation zone in the subsurface of the pickled steel.The internal oxidation of hot-rolled ultra-high strength steel must be precisely controlled to improve the subsequent surface quality of cold-rolled steel.

Microstructure and texture evolution of cold-rolled deep-drawing steel sheet during annealing

In accordance with experimental results about the annealing microstructure and texture of cold-rolled deep- drawing sheet based on the compact strip production （CSP） process, a two-dimensional cellular automation simulation model, considering real space and time scale, was established to simulate recrystallization and grain growth during the actual batch annealing process. The simulation results show that pancaked grains form during recrystallization. （111} advantageous texture components become the main parts of the recrystallization texture. After grain growth, the pancaked grains coarsen gradually. The content of （111} advantageous texture components in the annealing texture increases from 55vo1% to 65vo1%; meanwhile, the contents of {112}〈110〉 and {100}〈110〉 texture components decrease by 4% and 8%, respectively, compared with the recrystallization texture. The simulation results of microstructure and texture evolution are also consistent with the experimental ones, proving the accuracy and usefulness of the model.

Effect of Nb on the Microstructure and Properties of Cold Rolled and Annealed Mo Microalloyed Bainitic Steel

Two kinds of low carbon bainitic steels,Nb-free Mo bearing and Nb + Mo addition steels,were cold rolled and annealed to investigate the effect of micro-alloying element Nb on the microstructure and properties of Mo microalloyed low carbon high strength bainitic steel. No precipitates were observed in Nb-free Mo bearing steel,whereas,two types of precipitates,i.e.,Nb( C,N) and composite( Nb,Mo)( C,N),were observed in the Nb + Mo microalloyed steel,resulting in precipitation strengthening. The strength of Mo bearing steel was improved by addition of Nb under the same annealing conditions. The grain size of Nb addition steel was almost the same as Nb-free steel. Unlike the obvious grain refinement and precipitation strengthening in hot rolling,the increase in yield strength of Nb addition steels in cold rolling and annealing mainly results from the precipitation strengthening,while the effect of grain refinement strengthening can be almost ignored.

Study on the bendability and toughness of a 1 500 MPa cold-rolled martensitic sheet steel

Cold rolled martensitic sheet steels are achieving more and more applications in car-making because of their ultra-high strength and potential for weight reduction. The relatively low plasticity of ultra-high strength martensitic steels might be a drawback for the applications in the aspects of forming and safety protection function and should be significantly noted. A 1 500 MPa grade cold rolled martensitic sheet steel has been studied to investigate the bendability at 90 degree bending and impact toughness as well as fracture surface morphology at various temperatures. Some discussions have been made basing upon the experiment data to get some understanding on the performance of the materials under various conditions and on how to make use of this kind of ultra high strength steel properly.

Study on microstructure and properties of cold-rolled high strength steel for enameling

With its superior comprehensive properties, cold-rolled enameling steel is widely applied in many fields. However, its low yield stress greatly limits its application. This study aims to improve the yield stress of cold-rolled enameling steel under the premise of meeting formability and enameling properties by strengthening the ferrite matrix via solid strengthening of Mn. The grain size of ferrite before and after enameling,mechanical properties of annealed steel, and precipitation behavior of second-phase precipitates are obtained through studying the microstructure and properties of enameling steel at different stages. The microstructure of the steel investigated at room temperature is found to contain equiaxial ferrite and bunchy cementite particles;the ferrite grains have grown to some extent after enameling. The fine dispersed TiC particles and cementite particles contained in the annealed steel are the main factors improving the hydrogen storage capability. Finally, the result of a falling-ball impact test shows that the steel has achieved excellent adherence.

Research on the design of cold rolled ultra high strength sheet steel

This study researches cold rolled ultra high strength martensitic steel processed by water quenching. It is found that both the quenching and overageing temperatures greatly influence the mechanical properties of martensitic steel. A tensile strength of 1500 MPa can be obtained from 0.2% C-1.8% Mn steel by soaking at 840℃,quenching at 700℃ and overageing at 200℃ for several minutes. The continuous cooling transformation （CCT） diagram reveals that full martensite can be obtained at a cooling rate of 100℃/s or higher; and at a cooling rate of 3 - 10℃/s,austenite barely decomposes at 700℃. For steel with 0.2% carbon and less manganese, austenite decomposition occurs before it is cooled to 700℃ at a cooling rate of 3 - 10℃/s, which leads to lower tensile strength. It is possible to reduce the manganese content of the 1500 MPa martensitic steel by increasing the quenching temperature. To increase the quenching temperature,the control of flatness during water quenching becomes a major concern.

Study on direct cold rolling of hot rolled austenitic stainless steel SUS 304 with oxide scale

The austenitic stainless steel SUS 304 with oxide scale was directly cold rolled at different reductions of 10%, 20% and 30% respectively. It was proved that the surface quality （lower surface roughness） of the cold rolled products was achieved after subsequent annealing and pickling possesses, compared to the conventional hot rolled No. 1 product, whereas the grain size, mechanical and corrosion-resistant properties were comparable to those of the No. 1 product.

Surface rust of cold-rolled bell-type annealing strip steel

This paper offers systematic analysis and in-depth research on the surface rust problem of cold-rolled bell-type annealing strip products.The defect characteristics,occurrence rules,generation mechanism,and influencing factors of surface rust are presented.This research employed a cold-rolled bell-type furnace annealing unit in a coastal steel factory as an example and conducted production process tests,on-site production tests,scanning electron microscopy,energy spectrum analysis,MINITAB statistical analysis,etc.Moreover,six significant influencing factors and their rules were studied:the cooling time of the final cooling table,the storage time of the intermediate storage,the temperature setting of the intermediate storage,the temperature of leveling liquid,the purging pressure of leveling machine,and the dust in the environment.

Effect of water quenching processing parameters on the mechanical properties of a cold-rolled C-Mn-containing steel sheet

Cold-rolled advanced high-strength steel sheets have become the material of choice for the automotive industry because of their unique attributes of high strength and balanced mechanical properties.High-hydrogen gas jet cooling and water quenching are the most commonly used ultrafast cooling technologies for producing martensite-containing high-strength steel sheets.The water quenching technology ensures the fastest industrial cooling rate of 1 000 K/s;therefore,it has the highest potential with respect to saving alloys.In this study,the water quenching of a C-Mn-containing steel sheet is simulated during continuous annealing to investigate the effect of water quenching and tempering parameters on its mechanical properties.The results reveal that at low quenching temperatures,the strength of the steel sheet decreases as the soaking temperature increases.However,at high quenching temperatures,a high soaking temperature corresponds to increased strength after quenching,regardless of whether the material was austenitized in the single austenite zone or the inter-critical zone.Therefore,a high quenching temperature always results in a high strength and a high yield ratio after quenching.Low-temperature overaging(tempering) considerably influences the yield strength and yield ratio,and the extent of this influence is correlated with the soaking temperature.

Effect of annealing parameters on mechanical properties of cold-rolled martensitic steel sheets

Cold-rolled martensitic steel sheets produced on continuous annealing lines with water quenching facility,have advantages of high strength and low alloying element contents.These are in good accordance with the trend of light-weighting and fuel saving for automotive steel.In this article,a cold-rolled martensitic steel is studied to investigate the effect of annealing parameters on its mechanical properties.It is found that the quenching temperature and the slow cooling speed as well as the overageing temperature have significant influence on the strength of the experimental steel.The temperature zone at which the austenite decomposition is slow or has not started may be chosen as the quenching temperature to ensure the steel’s strength stability.The slow cooling speed also influences the steel’s strength greatly.A high cooling rate will lead to significantly higher strength.Tempering would decrease the steel’s tensile strength but would increase its yield strength.

Development and application of Baosteel's cold-rolled martensitic steel sheets

Cold-rolled martensitic steel sheets are becoming widely applied in the automotive industry because of their ultra-high strength,which may result in satisfactory weight reduction. The grades of martensitic steel sheets are classified based on their tensile strength,which ranges from 980 to 1 700 MPa. The main applications include a series of structural parts of uniform cross-section or simple shape,such as bumper beams,door beams and door sills,etc. The study and development of cold-rolled martensitic steel sheets date back to 2007 in Baosteel,and some grades became commercially available in 2009. By 2015,Baosteel had commercially supplied thousands of tons of these steel sheets with tensile strength up to 1 400 MPa. Currently,1 500 MPa martensitic steel sheet is commercially available and 1 700 MPa martensitic steel sheet has been successfully produced. The process technology and application guides of Basoteel ＇s cold-rolled martensitic steels are summarized and analyzed in order to assist ongoing research and ensure correct applications of these ultra-high strength steel sheets.

Fatigue Response of Cold-Rolled Type-304 Stainless Steel Foil

This study presents the fatigue response of 304 stainless steel foil, cold-rolled to a thickness of 3.2 μm with 87 percent cold work at orientations of 0, 45, and 90 degrees to the direction of rolling. Fatigue specimens were fabricated by laminating a supportive layer of 20-μm polyimide film to one side of the foil and patterning 242 crack initiation features by photolithographic process. Progression of fatigue damage was determined through electrical resistance measurement. The fatigue response was demonstrated to be largely affected by anisotropy existing between the rolling direction and the off-axis orientations. Fatigue cracks that traveled in a direction parallel to the elongated grains (cyclic loads applied at 90-degree orientation to foil rolling direction) had the most fatigue response (undesirable characteristic). The construction of the specimens with thin foil supported by a film backing contributed to high fatigue threshold.

Properties of ultra-low carbon,cold-rolled sheet steels containing titanium or boron for use in enameling

Ultra-low carbon（ULC）,cold-rolled sheet steels for porcelain enameling containing alloys of titanium and boron are studied. The microstructure,mechanical properties,inclusions,and precipitates of the sheet steels are analyzed. The hydrogen permeation time of the sheet steels as-annealed and after skin-passed or cold-rolled at different reductions are measured. It is show n that the sheet steels possess different features of enameling properties in hydrogen permeability,fishscale resistance,and pinhole resistance.