Bonding enhancement of cold rolling TA1 P-Ti/AA6061 composite plates via surface oxidation treatment

TA1 P-Ti/AA6061 composite plate was produced by oxidizing the surface of the titanium plate and adopting a cold roll bonding process.The results revealed that the oxide film(Ti6O)prepared on the surface of TA1 pure titanium was easy to crack during the cold roll bonding,thereby promoting the formation of an effective mechanical interlock at the interface,which can effectively reduce the minimum reduction rate of the composite plates produced by cold rolling of titanium and aluminium plates.Moreover,the composite plate subjected to oxidation treatment exhibited high shear strength,particularly at a 43%reduction rate,achieving a commendable value of 117 MPa.Based on oxidation treatment and different reduction rates,the annealed composite plates at temperatures of 400,450,and 500°C displayed favorable resistance to interface delamination,highlighting their remarkable strength-plasticity compatibility as evidenced by a maximum elongation of 31.845%.

Effects of cold rolling and heat treatment on microstructure and mechanical properties of AA 5052 aluminum alloy

The microstructures and mechanical properties of homogenized-rolled AA5052 aluminum alloys with different rolling reductions and following annealing treatments were investigated by optical microscope, scanning electron microscope, X-ray diffractometer, micro-hardness and tensile tests. The results show that with increasing rolling reduction, the equiaxed grains are elongated along the rolling direction obviously, and accumulation of rolling reduction increases the work hardening effect, which results in the enhanced strength and degraded plasticity. When rolling reduction is 87%, the ultimate tensile strength reaches 325 MPa but elongation is only 2.5%. There are much more secondary phase precipitates after annealing treatment. With an increase of annealing temperature, the amount of precipitates increases and work hardening diminishes continuously. The elongation is improved to ~23% but the tensile strength is decreased to 212 MPa after annealing at 300 °C for 4 h, which are comparable to those of as-homogenized alloy.

Deformation mechanism of cold ring rolling in view of texture evolution predicted by a newly proposed polycrystal plasticity model

An explicit polycrystal plasticity model was proposed to investigate the deformation mechanism of cold ring rolling in view of texture evolution. The model was created by deducing a set of linear incremental controlling equations within the framework of crystal plasticity theory. It was directly solved by a linear algorithm within a two-level procedure so that its efficiency and stability were guaranteed. A subroutine VUMAT for ABAQUS/Explicit was developed to combine this model with the 3D FE model of cold ring rolling. Results indicate that the model is reliable in predictions of stress-strain response and texture evolution in the dynamic complicated forming process; the shear strain in RD of the ring is the critical deformation mode according to the sharp Goss component （{110}？100？） of deformed ring; texture and crystallographic structure of the ring blank do not affect texture type of the deformed ring;texture evolves rapidly at the later stage of rolling, which results in a dramatically increasing deformation of the ring.

Relationship between Hardness and Deformation during Cold Rolling Process of Complex Profles

The hardening on surface of complex profles such as thread and spline manufactured by cold rolling can efectively improve the mechanical properties and surface quality of rolled parts. The distribution of hardness in superfcial layer is closely related to the deformation by rolling. To establish the suitable correlation model for describing the relationship between strain and hardness during cold rolling forming process of complex profles is helpful to the optimization of rolling parameters and improvement of rolling process. In this study, a physical analog experiment refecting the uneven deformation during complex-profle rolling process has been extracted and designed, and then the large date set (more than 400 data points) of training samples refecting the local deformation characteristics of complexprofle rolling have been obtained. Several types of polynomials and power functions were adopted in regression analysis, and the regression correlation models of 45# steel were evaluated by the single-pass and multi-pass physical analog experiments and the complex-profle rolling experiment. The results indicated that the predicting accuracy of polynomial regression model is better in the strain range (i.e., ε < 1.2) of training samples, and the correlation relationship between strain and hardness out strain range (i.e., ε > 1.2) of training samples can be well described by power regression model;so the correlation relationship between strain and hardness during complex-profle rolling process of 45# steel can be characterized by a segmented function such as third-order polynomial in the range ε < 1.2 and power function with a ftting constant in the range ε > 1.2;and the predicting error of the regression model by segmented function is less than 10%.

Texture evolution of commercial pure Ti during cold rolling and recrystallization annealing

X-ray diffraction （XRD） was employed to analyze the texture evolution of commercial pure （CP） Ti during cold rolling and re- crystallization annealing. The texture components were measured by electron backscattered diffraction （EBSD） after recrystallization an- nealing. The CP Ti tends to form a texture with the basal pole tilted 30°-40° away from the normal direction toward the transverse direction. The texture of the initial hot-rolled plate can be classified into three kinds, i.e., the pyramid texture （1013）[5230] and （2021）[1015], the basal plane texture （0001）[2110], and the stronger_prism_texture （1120）[0001]. After cold rolling and annealing （700℃,60 min）,_the main texture components are the cold-rolled texture （1125）[1123] and the recrystallized texture （1013）[5230]. The texture （2021）[1015] is in- herited from the texture of the initial hot-rolled plate with the decrease of orientation density gradually. The volume contents of the cold-rolled texture {2115}（0110） and the recrystallized texture {1013}（1210） are calculated by EBSD. After recrystallization annealing, the specimen is rich in the recrystallized texture and inherits some of texture components from the cold-rolled texture. When the annealing time is prolonged, the anisotropic value decreases.

Microstructural Evolution of Pearlite in Eutectoid Fe-C Alloys during Severe Cold Rolling

The microstructural evolution of pearlite during severe cold rolling in Fe-0.8C binary alloy and Fe-1Mn-0.8C ternary alloys was investigated by using SEM, TEM and XRD etc. The results show that the deformed pearlite consists of irregularly bent lamella, coarse lamella with shear-band and fine lamella. As the rolling reduction increases, the proportion of fine lamella increases. The strong plastic deformation, amorphization and dissolution of cementite take place during the severe cold rolling. The maximum carbon content in ferrite reaches 0.15 mass% after 90% cold rolling.

Control of Surface Thermal Scratch of Strip in Tandem Cold Rolling

The thermal scratch seriously affects the surface quality of the cold rolled stainless steel strip. Some researchers have carried out qualitative and theoretical studies in this field. However, there is currently a lack of research on effective forecast and control of thermal scratch defects in practical production, especially in tandem cold rolling. In order to establish precise mathematical model of oil film thickness in deformation zone, the lubrication in cold rolling process of SUS410L stainless steel strip is studied, and major factors affecting oil film thickness are also analyzed. According to the principle of statistics, mathematical model of critical oil film thickness in deformation zone for thermal scratch is built, with fitting and regression analytical method, and then based on temperature comparison method, the criterion for deciding thermal scratch defects is put forward. Storing and calling data through SQL Server 2010, a software on thermal scratch defects control is developed through Microsoft Visual Studio 2008 by MFC technique for stainless steel in tandem cold rolling, and then it is put into practical production. Statistics indicate that the hit rate of thermal scratch is as high as 92.38%, and the occurrence rate of thermal scratch is decreased by 89.13%. Owing to the application of the software, the rolling speed is increased by approximately 9.3%. The software developed provides an effective solution to the problem of thermal scratch defects in tandem cold rolling, and helps to promote products surface quality of stainless steel strips in practical production.

Microstructure and textural evolution during cold rolling and annealing of commercially pure titanium sheet

The effects of cold rolling and annealing on the microstructure and textural evolution of a commercially pure titanium（CP-Ti） sheet were investigated. Electron backscatter diffractometry demonstrates that the deformation during rolling is accommodated by twinning and slip. Additionally, twinning is the dominant deformation mechanism when the cold rolling reduction is less than 40%. During rolling, {11ˉ22}11ˉ2ˉ3contraction twinning（CT） and {10ˉ12}10ˉ11 extension twinning（ET） are activated. And, the intensity of the（0002） pole along the ND gradually increases with increasing deformation. During annealing, the fraction of low angle grain boundaries（LAGBs） and the intensity of the（0002） pole along the ND gradually decrease slightly with increasing annealing time, while twinning lamellae disappear rapidly. When the annealing time reaches 60 min, 20% cold-rolled sheet recrystallizes almost completely.

Effect of cold rolling on the microstructural, magnetic, mechanical, and corrosion properties of AISI 316L austenitic stainless steel

This study has evaluated the effect of different levels of cold rolling（from 0 to 50%）on the microstructural,magnetic,and mechanical properties and the corrosion behavior of 316L austenitic stainless steel in Na Cl（1 mol/L）＋H_2SO_4（0.5 mol/L）solution.Microstructural examinations using optical microscopy revealed the development of a morphological texture from coaxial to elongated grains during the cold-rolling process.Phase analysis carried out on the basis of X-ray diffraction confirmed the formation of the ferromagneticα′-martensite phase under the stresses applied during cold rolling.This finding is in agreement with magnetic measurements using a vibrating sample magnetometer.Mechanical properties determined by tensile and Vickers microhardness tests demonstrated an upward trend in the hardness-to-yield strength ratio with increasing cold-rolling percentage,representing a reduction in the material’s work-hardening ability.Uniform and localized corrosion parameters were estimated via potentiodynamic polarization corrosion tests and electrochemical impedance spectroscopy.In contrast to the uniform corrosion,wherein the corrosion current density increased with increasing cold-working degree because of the high density of microstructural defects,the passive potential range and breakdown potential increased by cold working,showing greater resistance to pit nucleation.Although pits were formed,the cold-rolled material repassivation tendency decreased because of the broader hysteresis anodic loop,as confirmed experimentally by observation of the microscopic features after electrochemical cyclic polarization evaluations.

冷轧变形对CoCrNi中熵合金显微组织和力学性能的影响

中熵合金具有多种优异性,同时具有高强度和延展性。冷轧变形是提高中熵合金力学性能的一种即经济又有效的方法。对CoCrNi中熵合金进行室温不同变形量(25%,37.5%,50%,62.5%,75%)的冷轧,通过X射线衍射分析、显微组织分析和拉伸试验研究了室温下不同变形量对合金显微组织和力学性能的影响。结果表明:在室温不同变形量冷轧下CoCrNi中熵合金的组织仍为单一的FCC结构。CoCrNi中熵合金室温抗拉强度较低,随着变形量的增加,抗拉强度显著提升,但延展性相比铸态变差。

Microstructures of ultra-fine grained FeCoV alloys processed by ECAP plus cold rolling and their evolutions during tempering

A new processing method,equal channel angular pressing(ECAP)plus cold rolling(CR),was applied to producing ultra-fine grained FeCoV alloy.The microstructures of ultra-fine grained FeCoV alloy after ECAP,ECAP plus CR,and the effect of tempering treatment on the microstructure of FeCoV alloy produced by ECAP plus CR were investigated.The results show that an elongated substructure with a width of about 0.3μm is obtained after four-pass ECAP using Route A.Cold rolling after ECAP cannot change the morphologies of elongated substructure,and it results in higher fraction of high-angle boundaries and higher dislocation density compared with the identical ECAP without rolling.Subsequent tempering for 30 min at 853 K brings about many nano-phases precipitating at subgrain boundaries and insides the grains,and the size of precipitated phase is measured to be about 10 nm.Nano-phases grow up with increasing tempering temperature and equiaxed structure forms at 883 K.

INFLUENCE OF COLD ROLLING REDUCTION ON MICROSTRUCTURE AND MECHANICAL PROPERTIES OF TWIP STEEL

The influence of cold rolling reduction on microstructure and mechanical properties of the TWIP （ttwinning induced plasticity） steel was investigated. The results＇ indicated that the steel had better comprehensive mechanical properties when cold rolling reduction was about 65.0% and the annealing temperature was 1000℃. The tensile strength of the steel is about 640MPa and the yield strength is higher than 255MPa, while the elongation is＇ above 82%. The microstructure is composed of austenitic matrix and annealing twins at room temperature, at the same time, a significant amount of annealing twins and stacking faults＇ are observed by transmission electron microscopy （TEM）. Mechanical twins play a dominant role during deformation, and result in exceUent mechanical properties.

Experimental Study and Finite Element Polycrystal Model Simulation of the Cold Rolling Textures in a Powder Metallurgy Processed Pure Aluminum Plate

Ingot metallurgy (IM) aluminum has long been the subject and attracted the attention of many metallurgists and textural researchers of materials. Due to the introduction of large amounts of ex situ interfaces, however, the textures in powder metallurgy (PM) processed aluminum has been rarely reported. In this article, a pure aluminum plate was prepared via PM route. The starting billet was first produced with uni-axially cold compaction and flat hot-extrusion and then followed by cold rolling processes. The hot-extruded and cold rolling deformation textures of the pure PM aluminum at 50%, 80% and 90% cold rolling reductions were studied by orientation distribution functions (ODFs) analysis. The finite element polycrystal model (FEPM) was finally utilized to simulate the cold rolling textural evolution at various stages of cold rolling. In FEPM simulation, the initial hot-extruded textures were taken into account as inputs. The results showed that typical β-fiber texture formed in pure PM aluminum with the cold rolling reduction increased till 80%, and there was not much change after excessive cold rolling deformation. Homogeneous slip is not the only deformation mode in PM processed pure aluminum plate at over 80% cold rolling reduction. The experimental results were qualitatively in good agreement with the simulated ones.

Backup roll contour of a SmartCrown tandem cold rolling mill

SmartCrown was a new system developed by VAI for improving the strip profile and flatness control first applied in 1700 mm tandem cold rolling mills at Wuhan Iron ＆ Steel （Group） Corporation （WISCO）. After tracing and testing, the application of the conventional crown backup roll matching the SmartCrown work roll of the production mill led to heavy and nonuniform wear, and the edge spalling of the backup roll often occurred. A 3-dimension finite element model of roll stacks was established, which was used to analyze the above-mentioned problems, and it was found that the main reason was the highly nonuniform contact pressure distribution between the work roll and the backup roll. A new FSR （flexible shape backup roll） was developed and applied in 1700 mm tandem cold rolling mills. A lot of good actual effects of FSR, such as evident improvement in profile and flatness of strips, non-occurring edge spalling, wear uniform, and remarkable decrease in roll consumption were validated by long-term industrial applications.

Microstructure and texture evolution in commercial-purity Zr 702 during cold rolling and annealing

Microstructure and texture evolution in commercial-purity Zr 702 during cold rolling and annealing was investigated by optical microscopy, transmission electron microscopy, and X-ray diffraction. The results showed that crystallographic slip was the predominant deformation mechanism in the early stage of deformation. Deformation twins started to form when the rolling reduction was larger than 38.9%; both the dislocation density and the number of twins increased with increasing rolling reduction. The initial texture of the Zr 702 plate consisted of the basal fiber component. During cold rolling the strength of the basal fiber first decreased and then increased with increasing rolling reduction. The cold-rolled sheets were fully recrystallized after being annealed at 550℃. The recrystallization temperature and the size of recrystallized grains decreased with increasing rolling reduction. A larger rolling reduction resulted in a higher grain growth rate when the annealing temperature increased from 550℃ to 700℃. The recrystallization texture was characterized by a major basal fiber and a minor {0113}〈2110〉 component. The strength of the recrystallization texture increased with increasing rolling reduction.

Microstructure, cold rolling, heat treatment, and mechanical properties of Mg-Li alloys

The magnesium-lithium （Mg-Li） alloy exhibits two phase structures between 5.7wt% and 10.3wt% Li contents, consisting of the a （hcp） Mg-rich and the β （bcc） Li-rich phases, at room temperature. In the experiment, Mg-5Li-2Zn, Mg-9Li-2Zn, Mg-16Li-2Zn, Mg-22Li-2Zn, Mg-5Li-2Zn-2Ca, Mg-9Li-2Zn-2Ca, Mg-16Li-2Zn-2Ca, and Mg-22Li-2Zn-2Ca （wt%） were melted. During the melting process, the flux, which was composed of lithium chloride （LiCl） and lithium fluoride （LiF） in the proportion of 3：1 （mass ratio） and argon gas were used to protect the alloys from oxidation. The microstructure, mechanical properties, and cold-rolling workability of the wrought alloys were studied. The crystal grain of the alloys （adding Ga） is fine . The hardness of the studied alloys decreases with an increase in element Li. The density of the studied alloys is in the range of 1.187 to 1.617 g/cm^3. The reduction of the Mg-16Li-2Zn and Mg-22Li-2Zn alloys can exceed 85% at room temperature. The Mg-9Li-2Zn-2Ca alloy was heat treated at 300℃ for 8, 12, 16, and 24 h, respectively. The optimum heat treatment of the Mg-9Li-2Zn-2Ca alloy is 300℃×12h by metallographic observation and by studying the mechanical properties of the alloys.

MICROSTRUCTURE EVOLUTION AND MECHANICAL HARDENING OF HYPEREUTECTOID PEARLITIC STEEL DURING COLD ROLLING

The microstructure evolution of different cold rolling reductions （from 0 to 81.6%） was studied by SEM （scanning electron microscopy） and TEM （transmission electron microscope）. The study showed that the orientation multiplicity of pearlitic lamellas resulted in inhomogeneous deformation of different pearlitic lamellas, and with the increase of reduction, the microstructure underwent a course of ＂homogeneity → inhomogeneity → homogeneity＂. The result of XRD （X-ray diffraction） analysis indicated that cementite did not decompose and dissolve into ferrite; the results of the mechanical property test suggested that the relationship between Rp0.2 （yield strength） and ε （true strain） was in good agreement with Hollomon relationship. With the equation Rp0.2 = 1465ε^0.18, the yield strength of the steel in different reductions could be well predicted.

Deformation and recrystallization behavior of a Fe-20Mn-3Si-3Al-0.045C steel under cold-rolling

The influence of cold rolling reduction on microstructure and mechanical properties of the twinning induced plasticity(TWIP) steel with a chemical composition of Fe-20Mn-3Si-3Al-0.045 C has been investigated.Tensile tests were carried out to explore the mechanical properties of TWIP steel with different cold rolling reductions.The microstructures were observed by optical microscopy and transmission electron microscopy(TEM).The misorientation and the development of recrystallization texture in TWIP steel sheets were investigated by Electron Back Scatter Diffraction(EBSD) technique.The results indicated that the steel exhibited attractively mechanical properties when cold rolling reduction was about 10%.The tensile strength of the steel with a rolling reduction of 10%is higher than 900 MPa and the yield strength is about 800 MPa,while the elongation is above 35%.The microstructure is composed of austenitic matrix and deformation twins at room temperature,at the same time,a significant amount of deformation twins,stacking faults and dislocations are observed by TEM.TEM observations showed the presence of deformation twinning in the sample at low rolling reduction.As the strain increases the volume fraction of twins increases.Mechanical twins play a dominant role during deformation and result in excellent mechanical properties for the investigated steel.By TEM observation,the possible deformation mechanisms can be suggested as:with the increasing strain,formation of the twin will gradually play a more important role during deformation.The interaction between twins and dislocations enhances the strain hardening rate in the sample.Consequently,the necking is delayed and a good ductility is obtained.Twins were always observed in the region with high density of dislocation and faults,suggesting that the interaction among blocked dislocations and faults as well as deformation twins promote the increase in material strength.EBSD observation showed that the textures has evolved according to the following trend:the brass orientation {110}〈112〉and Goss orientation {110}〈001〉are dominant at every strain level,those intensities increase with increasing strain,while with the increase of the strain level,the change of S orientation {123}〈634〉was not obviously.

Analysis of the cause of crack in cold rolling of QSn6.5-0.1 strip

In order to know the cause of cracks in cold rolling of QSn6.5 0.1 copper alloy strip, a lot of experiments and analysis were done. The microstructure changes of QSn6.5 0.1 were investigated by means of metallurgical microscope. The morphology of cracks and surface defects were examined using scanning electron microscope. Macroscopic residual stresses produced in every process during manufacturing in the QSn6.5 0.1 strip were measured by X ray diffraction method and hole drilling method. The results show that the cracks in the QSn6.5 0.1 cold rolling strip were caused due to the derivation of metallurgical defects, such as SnO 2, S, fine looses,the inverse segregation unable to clear up when milling, and the accumulation of all kinds of resi dual stresses. When the accumulation of the residual stress reaches the material′s breaking strength, the cracks will be generated. Several measures to avoid the development of these kinds of cracks were put forward, such as: controlling the casting technology, improving homogenization annealing procedure (680 ℃/7 h) and milling quality(using the second milling when necessary), working out a more reasonable rolling technology to ensure intermediate annealing in time.

轧制压下率、路径对NiCoCr合金微观结构和力学性能的影响

通过开展不同轧制压下率和路径的轧制实验,制备了具有不同比例和尺寸的纳米孪晶和纳米晶结构NiCoCr合金。透射电镜表征结果表明,单向轧制压下率50%样品中微观结构特征以纳米孪晶和高密度位错为主。当压下率达到90%,由于剪切带在纳米孪晶片层结构中的开动,孪晶体积分数下降,同时剪切带内形成大量尺寸为35 nm的纳米晶结构。多方向轧制样品中微观结构以纳米晶结构为主,平均尺寸为27 nm,略小于单向轧制压下率90%样品中的纳米晶尺寸。拉伸实验结果表明:相比于轧制前固溶态粗晶合金,单向轧制压下率50%纳米孪晶镍基合金强度大幅提高,合金屈服强度和抗拉强度分别达到1312 MPa和1396 MPa。压下率90%轧制样品屈服强度高达1599 MPa,变方向轧制样品屈服强度更是高达1705 MPa。同时拉伸试验数据表明,晶粒细化可以有效地提高材料强度,但是材料的延伸率显著下降。