Microstructure evolution and mechanical properties of 1000 MPa cold rolled dual-phase steel

The microstructure evolution of 1 000 MPa cold rolled dual-phase (DP) steel at the initial heating stages of the continuous annealing process was analyzed. The effects of different overaging temperatures on the microstructures and mechanical properties of 1 000 MPa cold rolled DP steel were investigated using a Gleeble-3500 thermal/mechanical simulator. The experimental results show that ferrite recovery and recrystallization, pearlite dissolution and austenite nucleation and growth take place in the annealing process of ultra-high strength cold rolled DP steel. When being annealed at 800 ℃ for 80 s, the tensile strength and total elongation of DP steel can reach 1 150 MPa and 13%, respectively. The microstructure of DP steel mainly consists of a mixture of ferrite and martensite. The steel exhibits low yield strength and continuous yielding which is commonly attributed to mobile dislocations introduced during cooling process from the intercritical annealing temperature.

Effect of cold rolling on the microstructural, magnetic, mechanical, and corrosion properties of AISI 316L austenitic stainless steel

This study has evaluated the effect of different levels of cold rolling（from 0 to 50%）on the microstructural,magnetic,and mechanical properties and the corrosion behavior of 316L austenitic stainless steel in Na Cl（1 mol/L）＋H_2SO_4（0.5 mol/L）solution.Microstructural examinations using optical microscopy revealed the development of a morphological texture from coaxial to elongated grains during the cold-rolling process.Phase analysis carried out on the basis of X-ray diffraction confirmed the formation of the ferromagneticα′-martensite phase under the stresses applied during cold rolling.This finding is in agreement with magnetic measurements using a vibrating sample magnetometer.Mechanical properties determined by tensile and Vickers microhardness tests demonstrated an upward trend in the hardness-to-yield strength ratio with increasing cold-rolling percentage,representing a reduction in the material’s work-hardening ability.Uniform and localized corrosion parameters were estimated via potentiodynamic polarization corrosion tests and electrochemical impedance spectroscopy.In contrast to the uniform corrosion,wherein the corrosion current density increased with increasing cold-working degree because of the high density of microstructural defects,the passive potential range and breakdown potential increased by cold working,showing greater resistance to pit nucleation.Although pits were formed,the cold-rolled material repassivation tendency decreased because of the broader hysteresis anodic loop,as confirmed experimentally by observation of the microscopic features after electrochemical cyclic polarization evaluations.

INFLUENCE OF COLD ROLLING REDUCTION ON MICROSTRUCTURE AND MECHANICAL PROPERTIES OF TWIP STEEL

The influence of cold rolling reduction on microstructure and mechanical properties of the TWIP （ttwinning induced plasticity） steel was investigated. The results＇ indicated that the steel had better comprehensive mechanical properties when cold rolling reduction was about 65.0% and the annealing temperature was 1000℃. The tensile strength of the steel is about 640MPa and the yield strength is higher than 255MPa, while the elongation is＇ above 82%. The microstructure is composed of austenitic matrix and annealing twins at room temperature, at the same time, a significant amount of annealing twins and stacking faults＇ are observed by transmission electron microscopy （TEM）. Mechanical twins play a dominant role during deformation, and result in exceUent mechanical properties.

Controlled Rolling and Cooling Process for Low Carbon Cold Forging Steel

Effect of controlled rolling and cooling process on the mechanical properties of low carbon cold forging steel was investigated for different processing parameters of a laboratory hot rolling mill. The results show that the specimens with fast cooling after hot rolling exhibit very good mechanical properties, and the improvement of the mechanical properties can be attributed mainly to the ferrite-grain refinement. The mechanical properties increase with decreasing final cooling temperature within the range from 670 ℃ to 570 ℃ due to the finer interlamellar spacing of pearlite colony. The specimen with fast cooling after low temperature rolling shows the highest values of the mechanical properties. The effect of the ferrite grain size on the mechanical properties was greater than that of pearlite morphology in the present study. The mechanical properties of specimens by controlled rolling and cooling process without thermal treatment were greatly superior to that of the same specimens by the conventional rolling, and their tensile strength reached 490 MPa grade even in the case of low temperature rolling without controlled rolling. It might be expected to realize the substitution medium-carbon by low-carbon for 490 MPa grade cold forging steel with controlled rolling and cooling process.

Mechanical performance and texture characteristic of an IF steel containing Nb and Ti by double cold rolling

Single cold rolling and double cold rolling were applied to hot rolled strips with different reduction ratios. The evolutions of { 100}, { 111} and Goss face texture during double rolling were investigated by comparing the orientation distribution function （ODF） of the double rolled sample with that of the single rolled one. The double cold rolling texture is characterized by a higher γ-texture and a lower α-texture, and the { 111}〈112〉 component is improved remarkably. Based on the TEM observation and mechanical properties test, it is found that the reduction ratio assignment significantly affects the texture variation, as-annealing microstructures, and properties of the double cold rolled samples. These results may provide a theoretical guide for the industrial production of double cold rolled IF steel.

MICROSTRUCTURE EVOLUTION AND MECHANICAL HARDENING OF HYPEREUTECTOID PEARLITIC STEEL DURING COLD ROLLING

The microstructure evolution of different cold rolling reductions （from 0 to 81.6%） was studied by SEM （scanning electron microscopy） and TEM （transmission electron microscope）. The study showed that the orientation multiplicity of pearlitic lamellas resulted in inhomogeneous deformation of different pearlitic lamellas, and with the increase of reduction, the microstructure underwent a course of ＂homogeneity → inhomogeneity → homogeneity＂. The result of XRD （X-ray diffraction） analysis indicated that cementite did not decompose and dissolve into ferrite; the results of the mechanical property test suggested that the relationship between Rp0.2 （yield strength） and ε （true strain） was in good agreement with Hollomon relationship. With the equation Rp0.2 = 1465ε^0.18, the yield strength of the steel in different reductions could be well predicted.

Deformation and recrystallization behavior of a Fe-20Mn-3Si-3Al-0.045C steel under cold-rolling

The influence of cold rolling reduction on microstructure and mechanical properties of the twinning induced plasticity(TWIP) steel with a chemical composition of Fe-20Mn-3Si-3Al-0.045 C has been investigated.Tensile tests were carried out to explore the mechanical properties of TWIP steel with different cold rolling reductions.The microstructures were observed by optical microscopy and transmission electron microscopy(TEM).The misorientation and the development of recrystallization texture in TWIP steel sheets were investigated by Electron Back Scatter Diffraction(EBSD) technique.The results indicated that the steel exhibited attractively mechanical properties when cold rolling reduction was about 10%.The tensile strength of the steel with a rolling reduction of 10%is higher than 900 MPa and the yield strength is about 800 MPa,while the elongation is above 35%.The microstructure is composed of austenitic matrix and deformation twins at room temperature,at the same time,a significant amount of deformation twins,stacking faults and dislocations are observed by TEM.TEM observations showed the presence of deformation twinning in the sample at low rolling reduction.As the strain increases the volume fraction of twins increases.Mechanical twins play a dominant role during deformation and result in excellent mechanical properties for the investigated steel.By TEM observation,the possible deformation mechanisms can be suggested as:with the increasing strain,formation of the twin will gradually play a more important role during deformation.The interaction between twins and dislocations enhances the strain hardening rate in the sample.Consequently,the necking is delayed and a good ductility is obtained.Twins were always observed in the region with high density of dislocation and faults,suggesting that the interaction among blocked dislocations and faults as well as deformation twins promote the increase in material strength.EBSD observation showed that the textures has evolved according to the following trend:the brass orientation {110}〈112〉and Goss orientation {110}〈001〉are dominant at every strain level,those intensities increase with increasing strain,while with the increase of the strain level,the change of S orientation {123}〈634〉was not obviously.

Improved cold rolling workability of warm rolled Fe?6.5wt%Si electrical steel with columnar grains by annealing

The effects of annealing temperature（with the annealing time being constant at 1 h） on the microstructure, ordering, residual stress, mechanical properties, and subsequent cold rolling workability of Fe-6.5wt%Si electrical steel with columnar grains were investigated, where the steel was warm rolled at 500℃ with a reduction of 95%. The results show that recrystallization began to occur in the sample annealed at 575℃ and that full recrystallization occurred in the sample annealed at 625℃. When the annealing temperature was 500℃ or greater, the extent of reordering in the sample was high, which reduced the room-temperature plasticity. However, annealing at temperatures below 300℃ did not significantly reduce the residual tensile stress on the edge of the warm rolled samples. Considering the comprehensive effects of annealing temperature on the recrystallization, reordering, residual stress, and mechanical properties of the warm rolled Fe-6.5wt%Si electrical steel with columnar grains, the appropriate annealing temperature range is 300℃-400℃. Unlike the serious edge cracks that appeared in the sample after direct cold rolling, the annealed samples could be cold rolled to a total reduction of more than 71.4% without the formation of obvious edge cracks, and bright-surface Fe-6.5wt%Si electrical steel strips with a thickness less than 0.1 mm could be fabricated by cold rolling.

Development and Lubricating Properties of Rolling Oil for Stainless Steel Cold Rolling

Appropriate base oils and homologous additives such as extreme pressure and anti-wear agents,oiliness agents and antioxidants were selected,and experiments testing the compatibility performance between additive,base oil and other components were carried out to develop the SK and SD series of rolling oils for cold rolling of stainless steel.The developed oils were used in the stainless steel cold rolling lubrication experiments,and were successfully applied in the actual cold rolling operation of stainless steel.Compared with a foreign product,the tribological properties,the thermal oxidation stability,and the rolling lubrication performance of the developed stainless steel cold rolling oils were studied.Test results showed that the tribological properties of the thereby developed rolling oils and the reference one were almost at the same level,and to some extent the performance of rolling was even better than the foreign product,at the same time the stainless steel sheet could retain its well annealed performance.Meanwhile,within a certain range,the lubrication of the rolling oil became better as its viscosity increased at the same level of saponification value,which could provide a lower friction coefficient,so that a higher maximum reduction ratio of the rolled piece through a constant roll gap and a minimum thickness could be secured.Also,similar phenomena appeared as the saponification value increased at a same viscosity level of the rolling oils.

Strain rate and cold rolling dependence of tensile strength and ductility in high nitrogen nickel-free austenitic stainless steel

The tensile strength and ductility of a high nitrogen nickel-free austenitic stainless steel with solution and cold rolling treatment were investigated by performing tensile tests at different strain rates and at room temperature. The tensile tests demonstrated that this steel exhibits a significant strain rate and cold rolling dependence of the tensile strength and ductility.With the increase of the strain rate from 10^-4s^-1to 1 s^-1, the yield strength and ultimate tensile strength increase and the uniform elongation and total elongation decrease. The analysis of the double logarithmic stress–strain curves showed that this steel exhibits a two-stage strain hardening behavior, which can be well examined and analyzed by using the Ludwigson equation. The strain hardening exponents at low and high strain regions（n2and n1） and the transition strain（εL） decrease with increasing strain rate and the increase of cold rolling RA. Based on the analysis results of the stress–strain curves, the transmission electron microscopy characterization of the microstructure and the scanning electron microscopy observation of the deformation surfaces, the significant strain rate and cold rolling dependence of the strength and ductility of this steel were discussed and connected with the variation in the work hardening and dislocation activity with strain rate and cold rolling.

Finite element analysis of deformation characteristics in cold helical rolling of bearing steel-balls

Due to the complexity of investigating deformation mechanisms in helical rolling(HR) process with traditional analytical method, it is significant to develop a 3D finite element(FE) model of HR process. The key forming conditions of cold HR of bearing steel-balls were detailedly described. Then, by taking steel-ball rolling elements of the B7008 C angular contact ball bearing as an example, a completed 3D elastic-plastic FE model of cold HR forming process was established under SIMUFACT software environment. Furthermore, the deformation characteristics in HR process were discovered, including the forming process, evolution and distribution laws of strain, stress and damage based on Lemaitre relative damage model. The results reveal that the central loosening and cavity defects in HR process may have a combined effect of large negative hydrostatic pressure(positive mean stress)caused by multi-dimensional tensile stresses, high level transverse tensile stress, and circular-alternating shear stress in cross section.

Study on metallurgical properties and pellet proportioning technology of stainless steel cold-rolling sludge

With a complicated composition, large rolling sludge has been a focal point concerning neither at home nor abroad have any technologies suitable for bulk utilization of stainless steel cold- production and serious damage to the environment, stainless steel cold- environmental protection for stainless steel enterprises. Up to now, come into being that are not only proper, safe and economical but also rolling sludge. Based on the characteristics of the stainless steel cold- rolling sludge, orthogonal experiments were carried out on pellet proportioning and high-temperature roasting, and major metallurgical properties of sludge pellets were also tested. As the results show, pellets with 30% addition of cold-rolling sludge are qualified regarding their compressive strength, chemical composition and major metallurgical properties. No adverse impact happens to the blast furnace operation when sludge pellets account for 10% of the blast furnace raw materials. Therefore, the technical route applied in this paper is proved simple, feasible and environmentally friendly for cold-rolling sludge treatment.

Effects of cold rolling on the microstructure and mechanical properties of Fe-Ni-Mn-Mo-Ti-Cr maraging steels

Effects of cold rolling on the microstructure and mechanical properties of Fe-Ni-Mn-Mo-Ti-Cr maraging steels were studied.To investigate the microstructure and mechanical properties,optical microscopy,scanning electron microscopy,X-ray diffraction,tensile test,and hardness test were used.The results show that the solution-annealing treatment in the cold-rolled steel redounds to the formation of sub-microcrystalline Fe2（Mo,Ti） Laves phase particles,which are stable at high temperatures.These secondary Laves phase particles prevent from recrystallization at high temperatures and correspond to semi-brittle fracture in the subsequent aging treatment.

Cold-rolling technologies of advanced high strength steels in Ansteel

Low - carbon becomes a high - frequency and fashionable word which gets the greatest concern in the world.Low - carbon refers to a minimal output of greenhouse gas emissions into the biosphere, specifically refers to the greenhouse gas carbon dioxide.To reduce energy consumption of automobile,more and more high strength steels are used by vehicle companies.To meet the request of vehicle companies, various high strength steels are developed in steel companies all over the world.Ansteel can provide,ultra-low carbon bake hardening(BH) steels,dual phase(DP) steels and transformation - induced plasticity (TRIP) steels with the grades of under 780 MPa,up to now.AHSS steels have much different composition, microstructure and strenght than conventional vehicle steels,so there are some trouble in producing in cold rolling mills,for example,difficult to join,poor thickness and flatness,accurate temperature and velocity control and so on.To reduce the opportunity of strip breakage,we have done many welding experiments and special research.Now,DP and TRIP steels can be continuously produced in Ansteel.To assure thickness and flatness of strips,we optimized the hot rolling parameter to get low deformation resistance,optimized rolling oil to get fit frictional coefficient and fix on the targat rolling curve.To get more accurate and repetitive results over the production shifts,the Mathematical Model(MM) is used in Ansteel.The MM analyses information transmitted by various sensors and transmitters,compares the collected data with the chosen parameters and adjusts the settings of the various pieces of equipment to hone on the parameter setpoints.At present,the key production technologies of AHSS were grasped by cold rolling mill Ansteel,and Ansteel is the first company to apply the TRIP with the grade of 780 MPa.

Application of cationic emulsion in stainless steel cold rolling

Emulsion, obtained by cationic emulsifiers, allows much larger oil droplets with narrower particle distribution, slows down the contamination from iron fines to the oil droplets, and is further enhanced with higher boundary and elastohydrodynamic lubrication for a relatively slower rolling process but high rolling force. As a result,it is suitable for the cold rolling of stainless steel. Cationic emulsion is now applied in a 1 750 mm 5-stand tandem cold rolling mill of Baosteel to roll stainless steel and carbon steel. The production process is stable and the product quality satisfies customer requirements.

Study on direct cold rolling of hot rolled austenitic stainless steel SUS 304 with oxide scale

The austenitic stainless steel SUS 304 with oxide scale was directly cold rolled at different reductions of 10%, 20% and 30% respectively. It was proved that the surface quality （lower surface roughness） of the cold rolled products was achieved after subsequent annealing and pickling possesses, compared to the conventional hot rolled No. 1 product, whereas the grain size, mechanical and corrosion-resistant properties were comparable to those of the No. 1 product.

Microstructural evolution of lamellar cementite in eutectoid steels by cold rolling

The pearlitic transformation and the deformation behavior of lamellar cementite after cold rolling in eutectoid steels Fe-0.76%C-0.137%Mn(mass fraction) were studied by means of Formastor-F (Full Automatic Transformation Testing Instrument) and field emission scanning electronic microscopy (FESEM) observation. Fine and coarse pearlite were obtained in the eutectoid steels austenitized at 900℃ for 15min, then hold at 620℃ for 90 s and 690℃ for 7 h, respectively. The deformation behavior of cold rolled lamellar cementite could be classified as: cleavage fracture, inhomogeneous slip, fragmentation, thinning or necking, and homogeneous bending. The cementite lamellae with the thickness of more than 100 nm could be deformed plastically.

Effect of deformation twinning on the evolution of texture in TWIP steels during cold-rolling

Texture evolution of high-manganese twining-induced plasticity (TWIP) steels (Fe-16Mn-0.6C) during cold-rolling is studied by means of quantitative orientation distribution function (ODF)analysis.Thickness reductions of the specimens during cold-rolling are 10%,20%,30%,50% and 65%,respectively.Evolution of texture is of the Brass type,which is typical for low-stacking fault energy (SFE) materials.The contribution of deformation twinning to the development of texture is clearly illustrated by the monotonic increase of the twinned Cu component.In the present study,the deformation twinning was identified as significantly contributing to deformation up to the maximum reduction applied.These results are useful for the prediction and control of the texture in TWIP steels.

Research and application on the automatic measuring device for testing transverse thickness difference of cold-rolling steel sheet

Many advanced technologies have been applied in developing the automatic measuring device for testing transverse thickness difference of cold-rolling steel sheet,such as the technologies of automatic control,sensor measurement,marking identification,photographic location,computer application and information transmission.This measuring device can measure the transverse thickness difference of the steel plate accurately and quickly,with a high detection level of automation.It is an effective detection equipment for transverse thickness control of steel plate.Horizontal width of steel plate measuring 0.8-1.4 m, horizontal measurement point positioning accuracy±0.02 mm,thickness range 0.2-2.0 mm, measurement accuracy within±1μm.

Analysis of formation causes for "oil-burn" defects and control measures during cold rolling of silicon steel

It has been found through analysis of defect components and micrographs that ＂oil-burn＂ defects on non- oriented silicon steel surf＇aces, which of ten occur after cold rolling, are composed of Fe, O, Si and C. This study analyzed the fomation mechanism of ＇toil-burn＂ defects and the strategies to prevent them,and proposed, according to the equipment and process status in the production fields ,some relevant optimized control measures and process adjustment schemes from two perspectives of reducing the residual emulsion trod avoiding the specific temperature range. The results demonstrate that the application of the proposed optimization meastu＇es effectively inhibits the formation of ＂oil-bum＂ defects.