Simulation of recrystallization based on EBSD data using a modified Monte Carlo model that considers anisotropic effects in cold-rolled ultra-thin grain-oriented silicon steel

A Monte Carlo Potts model was developed to simulate the recrystallization process of a cold-rolled ultra-thin grain-oriented silicon steel.The orientation and image quality data from electron backscatter diffraction measurements were used as input information for simulation.Three types of nucleation mechanisms,namely,random nucleation,high-stored-energy site nucleation(HSEN),and high-angle boundary nucleation(HABN),were considered for simulation.In particular,the nucleation and growth behaviors of Goss-oriented({011}<100>)grains were investigated.Results showed that Goss grains had a nucleation advantage in HSEN and HABN.The amount of Goss grains was the highest according to HABN,and it matched the experimental measurement.However,Goss grains lacked a size advantage across all mechanisms during the recrystallization process.

Effect of water quenching processing parameters on the mechanical properties of a cold-rolled C-Mn-containing steel sheet

Cold-rolled advanced high-strength steel sheets have become the material of choice for the automotive industry because of their unique attributes of high strength and balanced mechanical properties.High-hydrogen gas jet cooling and water quenching are the most commonly used ultrafast cooling technologies for producing martensite-containing high-strength steel sheets.The water quenching technology ensures the fastest industrial cooling rate of 1 000 K/s;therefore,it has the highest potential with respect to saving alloys.In this study,the water quenching of a C-Mn-containing steel sheet is simulated during continuous annealing to investigate the effect of water quenching and tempering parameters on its mechanical properties.The results reveal that at low quenching temperatures,the strength of the steel sheet decreases as the soaking temperature increases.However,at high quenching temperatures,a high soaking temperature corresponds to increased strength after quenching,regardless of whether the material was austenitized in the single austenite zone or the inter-critical zone.Therefore,a high quenching temperature always results in a high strength and a high yield ratio after quenching.Low-temperature overaging(tempering) considerably influences the yield strength and yield ratio,and the extent of this influence is correlated with the soaking temperature.

Effect of annealing parameters on mechanical properties of cold-rolled martensitic steel sheets

Cold-rolled martensitic steel sheets produced on continuous annealing lines with water quenching facility,have advantages of high strength and low alloying element contents.These are in good accordance with the trend of light-weighting and fuel saving for automotive steel.In this article,a cold-rolled martensitic steel is studied to investigate the effect of annealing parameters on its mechanical properties.It is found that the quenching temperature and the slow cooling speed as well as the overageing temperature have significant influence on the strength of the experimental steel.The temperature zone at which the austenite decomposition is slow or has not started may be chosen as the quenching temperature to ensure the steel’s strength stability.The slow cooling speed also influences the steel’s strength greatly.A high cooling rate will lead to significantly higher strength.Tempering would decrease the steel’s tensile strength but would increase its yield strength.

Development and application of Baosteel's cold-rolled martensitic steel sheets

Cold-rolled martensitic steel sheets are becoming widely applied in the automotive industry because of their ultra-high strength,which may result in satisfactory weight reduction. The grades of martensitic steel sheets are classified based on their tensile strength,which ranges from 980 to 1 700 MPa. The main applications include a series of structural parts of uniform cross-section or simple shape,such as bumper beams,door beams and door sills,etc. The study and development of cold-rolled martensitic steel sheets date back to 2007 in Baosteel,and some grades became commercially available in 2009. By 2015,Baosteel had commercially supplied thousands of tons of these steel sheets with tensile strength up to 1 400 MPa. Currently,1 500 MPa martensitic steel sheet is commercially available and 1 700 MPa martensitic steel sheet has been successfully produced. The process technology and application guides of Basoteel ＇s cold-rolled martensitic steels are summarized and analyzed in order to assist ongoing research and ensure correct applications of these ultra-high strength steel sheets.

Fatigue Response of Cold-Rolled Type-304 Stainless Steel Foil

This study presents the fatigue response of 304 stainless steel foil, cold-rolled to a thickness of 3.2 μm with 87 percent cold work at orientations of 0, 45, and 90 degrees to the direction of rolling. Fatigue specimens were fabricated by laminating a supportive layer of 20-μm polyimide film to one side of the foil and patterning 242 crack initiation features by photolithographic process. Progression of fatigue damage was determined through electrical resistance measurement. The fatigue response was demonstrated to be largely affected by anisotropy existing between the rolling direction and the off-axis orientations. Fatigue cracks that traveled in a direction parallel to the elongated grains (cyclic loads applied at 90-degree orientation to foil rolling direction) had the most fatigue response (undesirable characteristic). The construction of the specimens with thin foil supported by a film backing contributed to high fatigue threshold.

Properties of ultra-low carbon,cold-rolled sheet steels containing titanium or boron for use in enameling

Ultra-low carbon（ULC）,cold-rolled sheet steels for porcelain enameling containing alloys of titanium and boron are studied. The microstructure,mechanical properties,inclusions,and precipitates of the sheet steels are analyzed. The hydrogen permeation time of the sheet steels as-annealed and after skin-passed or cold-rolled at different reductions are measured. It is show n that the sheet steels possess different features of enameling properties in hydrogen permeability,fishscale resistance,and pinhole resistance.

Effect of normalizing cooling process on microstructure and precipitates in low-temperature silicon steel

Microstructure, precipitate and magnetic characteristic of fmal products with different normalizing cooling processes for Fe-3.2%Si low-temperature hot-rolled grain-oriented silicon steel were analyzed and compared with the hot-rolled plate by optical microscopy （OM）, transmission electron microscopy （TEM）, and energy dispersive spectrometry （EDS）. The results show that, the surface microstructure is uniform, the proportion of recrystallization in matrix increases, and the banding textures are narrowed; the precipitates, whose quantity in normalized plate is more than that in hot-rolled plate greatly, are mainly A1N, MnS, composite precipitates （Cu,Mn）S and so on. Normalizing technology with a temperature of 1120 ℃, holding for 3 min, and a two-stage cooling is a most advantaged method to obtain oriented silicon steel with sharper Goss texture and higher magnetic properties, owing to the uniform surface microstructures and the obvious inhomogeneity of microstructures along the thickness. The normalizing technology with the two-stage cooling is the optimum process, which can generate more fine precipitates dispersed over the matrix, and be beneficial for finished products to get higher magnetic properties.

Influence of silicon on the microstructures, mechanical properties and stretch-flangeability of dual phase steels

Uniaxial tension tests and hole-expansion tests were carried out to determine the influence of silicon on the microstructures, mechanical properties, and stretch-flangeability of conventional dual-phase steels. Compared to 0.03wt% silicon, the addition of 1.08wt% silicon induced the formation of finer ferrite grains （6.8μm ） and a higher carbon content of martensite （Cm≈ 0.32wt%）. AS the silicon level increased, the initial strain-hardening rate （n value） and the uniform elongation increased, whereas the yield strength, yield ratio, and stretch-flangeability decreased. The microstructures were observed after hole-expansion tests. The results showed that low carbon content martensite （Cm ≈ 0.19wt%） can easily deform in coordination with ferrite. The relationship between the mechanical properties and stretch-flangeability indicated that the steel with large post-uniform elongation has good stretch-flangeability due to a closer plastic incom- patibility of the ferrite and martensite phases, which can effectively delay the production and decohesion of microvoids.

Effects of Primary Annealing Condition on Recrystallization Texture in a Grain Oriented Silicon Steel

The recrystallization texture in grain oriented silicon steel sheets, which were annealed at different primary annealingtemperatures with and without an electric field, was investigated. An automated electron backscattered diffraction(EBSD) technique was used to analyze the recrystallization texture. It was found that recovery and application ofelectric field in primary annealing lead to an increase of {001} component and a decrease of {111} component afterannealing at 900℃. The development of recrystallization texture can be explained in terms of the effects of electricfield and primary annealing temperature on recovery.

Study on precipitation and transition mechanisms from the magnetic properties of silicon steel during annealing

Precipitates play an important role in determining the mechanical and magnetic properties of silicon steel. This paper aims to investigate the growth kinetics of precipitates in commercial silicon steel by analyzing its magnetic properties during isothermal annealing at 200℃. The growth of precipitates was studied by optical microscopy, scanning electron microscopy, transmission electron microscopy, and magnetic measurements. In combination with the coercive field and initial susceptibility, this technique offers the advantage of being non-destructive and providing quantitative information about the number, mean radius of precipitates, and fraction of transformation. An ob- served decrease in the number of precipitated particles indicates that the transformation starts from particles of appreciable initial size.

Behaviors of different inhibitors during secondary recrystallization of a grain-orientated silicon steel

The behaviors of different inhibitors including their composition, size, distribution, coalescence and coarsening were experimen-tally studied. It was observed that during secondary recrystallization of the tested steel, the key inhibition effect was produced by Cu2S and AlN, but not MnS. With the increase of temperature, the size distributions of AlN and Cu2S were changed to some extent. However, signifi-cant changes in particle size were not observed. The initial temperature of abnormal growth was determined by measuring the evolution of particle sizes and their distribution density during heat treatment. AlN and Cu2S are the dominant inhibitors and both are necessary, which is verified by calculating the Zener factor.

Preparation of special silicon steel grade MgO from hydromagnesite

A preparation technology of MgO powder used in special silicon steel from hydromagnesite mineral has been developed. The preparation technology includes the following steps： （1） calcining the hydromagnesite at 700-750°C for 1.5-2 h; （2） hydrating the calcined hydromagnesite to be slurry containing the solid-liquid ratio of 15-20 g？L？1; （3） acquiring Mg（HCO3）2 solution by carbonating the slurry, the carbonation temperature, CO2 pressure, and end point PH value of carbonation are less than 40°C, 0.4-0.6 MPa, and 7 respectively during the carbonation process; （4） preparing precipitated basic magnesium carbonate by thermally decomposing the Mg（HCO3）2 solution at 90-100°C; （5） obtaining the MgO product by calcining the precipitated basic magnesium carbonate at 850-950°C for 30-60 min, and adopting flowing nitrogen during the cooling process. By using this technology, more than 80wt% magnesium in hydromagnesite mineral can be extracted, and high-performance MgO products used in special silicon steel can be ob- tained.

Interactions of Sn and S and their effects on the magnetic properties of non-oriented silicon steel sheets

The interactions of Sn and S and their effects on the magnetic properties of non-oriented silicon steel sheets were discussed in reference to industrial production. Results show that minor amounts of Sn can improve magnetic induction sharply but have little effect on core loss when the S content is below 10 × 10 ^-4%. The precipitation of AlN can be restrained effectively by Sn. Sn, as the nucleus, can remove some of the inclusions with a size of 0.5μm or larger, but has little effect on inclusions smaller than 0.5 μm,which is the key factor affecting core loss. Sn improves the magnetic induction of finished steel sheets mainly through the change of the steel texture. The relationship between the magnetic induction and Sn and S content can be regressed as B50 = 1.69 -4.37 ws ＋0.30 Ws,. From the regression formulation,the magnetic induction can be improved by 0.03 T when 0.01% Sn is added under relatively low S content conditions.

Balanced solubility product and enthalpies of formation of Nb compounds in 0.09 % oriented silicon steel

Balance solubility products and enthalpy of for- mation for NbC0.75, NbC0.85, NbC0.88, NbC and NbN in oriented silicon steels were calculated and compared quali- tatively. Meanwhile, the mixing enthalpies of these five Nb compounds were calculated based on Miedema Model. The results show that the solubility products of Nb compounds in ferrite and austenite meet the following relationship, NbC0.75 〉 NbC0.85 〉 NbC0.88 〉 NbC 〉 NbN and NbN has the minimum enthalpy of formation. It indicates that NbN easily precipitate out, but it is more difficult for NbC0.75.

Characterization of Fe_3Si-based coatings on low silicon steel by pulsed Nd:YAG laser cladding

The Fe3Si based coating was produced on the Fe-1 Si steel surface by a pulsed Nd：YAG （yttrium aluminum garnet） laser. Its phase constitution and microstructure were characterized by using X-ray diffraction （XRD）, optical microscope （OM）, and field emission scanning electron microscope （FESEM） with associated energy dispersive spectroscopy （EDS） and transmission electron microscopy （TEM）. The hyperfine structure of the coating was studied by Mrssbauer spectra （MS） and the magnetic property was also measured at room temperature by a vibrating sample magnetometer （VSM）. The obtained coating is pore and crack-free with dense microstructure and high Si content. The metallurgical bonding between the coating and the substrate was realized. The microstructure of the coating is typical fine dendrites. The major phase was confirmed by XRD and TEM to be the ordering D03 structured Fe3Si phase. In addition, there were smaller amounts of the Fe5Si3 phase and the γ-Fe phase in the coating. Compared with the substrate, the laser cladding coating has a lower saturation magnetization and a higher coercive force. The poor magnetic property might be because of rapid solidification microstructure and phase constitution in the coating.

Effects of calcium treatment on non-metallic inclusions and magnetic properties of non-oriented silicon steel sheets

Based on the industrial production of non-oriented silicon steel,calcium treatment by CaSi wire feeding during the RH refining process was studied. The thermodynamics of CaS inclusion formation was analyzed, and the morphology and the size distribution were observed. Furthermore, the change in inclusion characteristics after calcium treatment and the effect of calcium treatment on magnetic properties were discussed. The results show that the formation of MnS and A1N inclusions were restrained, and the aggregating, floating and removing of microinclusions after calcium treatment were effectively promoted. The cleanliness of liquid steel was obviously increased. The main type of inclusions was single phase of CaO, with some complex inclusions composed of CaO, SiO2 and MgO. No CaS inclusion was observed after an appropriate calcium treatment. The size of all inclusions was distributed in the range of 2 - 20 μm, and the number was about 1.8 × 10^5/mm3. In addition, as an increasing amount of calcium was added,the core loss gradually decreased to a stable level, and the magnetic induction decreased quickly after a slow increase. The optimal calcium treatment mode depends on the chemical composition of steel.

Analysis of oxide layer structure in nitrided grain-oriented silicon steel

The production of low-temperature reheated grain-oriented silicon steel is mainly based on the acquired inhibitor method.Due to the additional nitriding process,a high nitrogen content exists in the oxide layer,which changes the structure of the oxide layer.In this study,the structure of the surface oxide layer after nitriding was analyzed by scanning electron microscopy(SEM),electron back-scattered diffraction(EBSD),glow discharge spectrometry(GDS),and X-ray diffraction(XRD).The size and orientation of ferritic grains in the oxide layer were characterized,and the distribution characteristics of the key elements along the thickness direction were determined.The results show that the oxide layer of the steel sample mainly comprised particles of Fe2SiO4 and spherical and lamellar SiO2,and Fe4N and fcc-Fe phases were also detected.Moreover,the size and orientation of ferritic grains in the oxide layer were different from those of coarse matrix ferritic grains beneath the oxide layer;however,some ferritic grains exhibited same orientations as those in the neighboring matrix.Higher nitrogen content was detected in the oxide layer than that in the matrix beneath the oxide layer.The form of nitrogen enrichment in the oxide layer was analyzed,and the growth mechanism of ferritic grains during the oxide layer formation is proposed.

Control of nonmetallic inclusions of non-oriented silicon steel sheets by the rare earth treatment

Based on the industrial production of non-oriented silicon steel, the rare earth （RE） treatment during the Ruhrstahl Heraeus （RH） refining process was studied. The morphology and the size distribution were observed for the steel specimens treated with different RE treatment conditions. Furthermore, the formation and change of the nonmetallic inclusion characteristics of finished steel sheets after the RE treatment were discussed. The results have shown that in the present work,the suitable RE metal additions are 0.6 -0.9 kg/t steel. After the suitable RE treatment,the formation of AIN and MnS inclusions were restrained, and the aggregation, flotation and removal of nonmetallic inclusions were efficiently promoted and the cleanliness of liquid steel was significantly increased. Meanwhile, the total oxygen concentration reached the minimum value and thle desulfurization efficiency was optimal ,and the type of main inclusions was approximately spherical or elliptical spherical RE radicle inclusions whose size was relatively large.

Pulsed Nd:YAG laser cladding of high silicon content coating on low silicon steel

A pulsed Nd：YAG （yttrium aluminum garnet） laser-based technique was employed to clad low silicon steel with preplaced Si and Fe mixed powders for high Si content. The surface morphology, microstructural evolution, phase composition, and Si distribution, within the obtained cladding coatings, were characterized by optical microscopy （OM）, field emission scanning electron microscopy （FE-SEM）, with associated energy dispersive spectroscopy （EDS）, transmission electron microscopy （TEM）, and X-ray diffraction （XRD）. The microhardness was also measured along the depth direction of the specimens, A crack- and pore-free cladding coating through excellent metallurgical bonding with the substrate was successfully prepared on low silicon steel by means of optimized single-track and multi-track laser cladding. The phases of the coating are a-Fe, T-Fe, and FeSi. The high microhardness of the lasercladding zone is considered as an increase in Si content and as the refined microstructure produced by the laser treatment. The Si contents of the cladding coatings were about 5.8wt% in the single-track cladding and 6.5wt% in the multi-track cladding, respectively.

STUDY ON REDUCING THE CORE LOSS OF GRAIN ORIENTED SILICON STEEL AND IMPROVING ITS AGING PROPERTY BY LASER NITRIDING TECHNIQUE IN ATMOSPHERIC AMBIENT

CW-CO2 laser nitriding technique was applied to improve the properties （such as aging property and the core loss） of grain oriented silicon steel. The samples were nitrided with regular space. Laser power density and scanning speed were chosen as 7.8×10^5W·cm^-2 and 100mm·min^-1. By some laser irradiation, Fe4N and Fe3N were formed in the nitrided zone. The nitrided samples were annealed at the temperatures ranged from 100 to 90℃. The core loss of some interested samples was tested. The results show that the core loss of the nitrided samples with different thickness of 0.23 and 0.30mm decreased by 14.9% and 9.4% respectively, and the aging property were improved up to 800℃. The mechanism of laser nitriding to improve the properties of grain oriented silicon steel is discussed.