Comparative analysis of thermodynamic and mechanical responses between underground hydrogen storage and compressed air energy storage in lined rock caverns

Underground hydrogen storage(UHS)and compressed air energy storage(CAES)are two viable largescale energy storage technologies for mitigating the intermittency of wind and solar power.Therefore,it is meaningful to compare the properties of hydrogen and air with typical thermodynamic storage processes.This study employs a multi-physical coupling model to compare the operations of CAES and UHS,integrating gas thermodynamics within caverns,thermal conduction,and mechanical deformation around rock caverns.Gas thermodynamic responses are validated using additional simulations and the field test data.Temperature and pressure variations of air and hydrogen within rock caverns exhibit similarities under both adiabatic and diabatic simulation modes.Hydrogen reaches higher temperature and pressure following gas charging stage compared to air,and the ideal gas assumption may lead to overestimation of gas temperature and pressure.Unlike steel lining of CAES,the sealing layer(fibre-reinforced plastic FRP)in UHS is prone to deformation but can effectively mitigates stress in the sealing layer.In CAES,the first principal stress on the surface of the sealing layer and concrete lining is tensile stress,whereas UHS exhibits compressive stress in the same areas.Our present research can provide references for the selection of energy storage methods.

Research on Operation Optimization of Heating System Based on Electric Storage Coupled Solar Energy and Air Source Heat Pump

For heating systems based on electricity storage coupled with solar energy and an air source heat pump(ECSA),choosing the appropriate combination of heat sources according to local conditions is the key to improving economic efficiency.In this paper,four cities in three climatic regions in China were selected,namely Nanjing in the hot summer and cold winter region,Tianjin in the cold region,Shenyang and Harbin in the severe cold winter region.The levelized cost of heat(LCOH)was used as the economic evaluation index,and the energy consumption and emissions of different pollutants were analyzed.TRNSYS software was used to simulate and analyze the system performance.The Hooke-Jeeves optimization algorithm and GenOpt software were used to optimize the system parameters.The results showed that ECSA systemhad an excellent operation effect in cold region and hot summer and cold winter region.Compared with ECS system,the systemenergy consumption,and the emission of different pollutants of ECSA system can be reduced by a maximum of 1.37 times.In cold region,the initial investment in an air source heat pump is higher due to the lower ambient temperature,resulting in an increase in the LOCH value of ECSA system.After the LOCH value of ECSA system in each region was optimized,the heating cost of the system was reduced,but also resulted in an increase in energy consumption and the emission of different pollutant gases.

Design and Development of Wind-Solar Hybrid Power System with Compressed Air Energy Storage for Voltage and Frequency Regulations

The intermittent nature of wind and solar photovoltaic energy systems leads to the fluctuation of power generated due to the fact that the power output is highly dependent upon local weather conditions, which results to the load shading issue that led to the voltage and frequency instability. In additional to that, the high proportions of erratic renewable energy sources can lead to erratic frequency changes which affect the grid stability. In order to reduce this effect, the energy storage system is commonly used in most wind-solar energy systems to balance the voltage and frequency instability during load variations. One of the innovative energy storage systems is the compressed air energy storage system (CAES) for wind and solar hybrid energy system and this technology is the key focus in this research study. The aim of this research was to examine the system configuration of the CAES system through modelling and experimental approach with PID controller design for regulating the voltage and frequency under different load conditions. The essential elements and the entire system have been presented in this work as thorough modelling in the MATLAB/Simulink environment for different load conditions. The developed model was tested through an experimental workbench using the developed prototype of the compressed air storage in the Siemens Lab at DeKUT and explored the consequence of the working parameters on the system proficiency and the model accuracy. The performance of the system for the developed prototype of CAES system was validated using results from an experimental workbench with MATLAB/Simulink R2022b simulation. The modeling and experimental results, shows that the frequency fluctuation and voltage drop of the developed CAES system during load variations was governed by the I/P converter using a PID_Compact controller programed in the TIA Portal V17 software and downloaded into PLC S7 1200. Based on these results, the model can be applied as a basis for the performance assessment of the compressed air energy storage system so as to be included in current technology of wind and solar hybrid energy systems.

A novel nano-grade organosilicon polymer:Improving airtightness of compressed air energy storage in hard rock formations

Enhancing cavern sealing is crucial for improving the efficiency of compressed air energy storage(CAES)in hard rock formations.This study introduced a novel approach using a nano-grade organosilicon polymer(NOSP)as a sealant,coupled with an air seepage evaluation model that incorporates Knudsen diffusion.Moreover,the initial coating application methods were outlined,and the advantages of using NOSP compared to other sealing materials,particularly regarding cost and construction techniques,were also examined and discussed.Experimental results indicated a significant reduction in permeability of rock specimens coated with a 7–10μm thick NOSP layer.Specifically,under a 0.5 MPa pulse pressure,the permeability decreased to less than 1 n D,and under a 4 MPa pulse pressure,it ranged between4.5×10^(-6)–5.5×10^(-6)m D,marking a 75%–80%decrease in granite permeability.The sealing efficacy of NOSP surpasses concrete and is comparable to rubber materials.The optimal viscosity for application lies between 95 and 105 KU,and the coating thickness should ideally range from 7 to 10μm,applied to substrates with less than 3%porosity.This study provides new insights into air transport and sealing mechanisms at the pore level,proposing NOSP as a cost-effective and simplified solution for CAES applications.

Performance Analysis of Constant-Pressure Pumped Hydro Combined with Compressed Air Energy Storage System Considering Off-Design Model of Compressor

With the wide application of renewable energy, energy storage technology has become a research hotspot. In order to overcome the shortcomings of energy loss caused by compression heating in compressed air energy storage technology, a novel constant-pressure pumped hydro combined with compressed air energy storage system was proposed. To deepen the understanding of the system and make the analysis closer to reality, this paper adopted an off-design model of the compressor to calculate and analyze the effect of key parameters on system thermodynamics performance. In addition, the results of this paper were compared with previous research results, and it was found that the current efficiency considering the off-design model of compressor was generally 2% - 5% higher than the previous efficiency. With increased preset pressure or with decreased terminal pressure, both the previous efficiency and current efficiency of the system increased. The exergy destruction coefficient of the throttle valve reached 4%. System efficiency was more sensitive to changes in water pump efficiency and hydroturbine efficiency.

Air tightness of compressed air storage energy caverns with polymer sealing layer subjected to various air pressures

During the operation of compressed air storage energy system,the rapid change of air pressure in a cavern will cause drastic changes in air density and permeability coefficient of sealing layer.To calculate and properly evaluate air tightness of polymer sealing caverns,the air-pressure-related air density and permeability must be considered.In this context,the high-pressure air penetration in the polymer sealing layer is studied in consideration of thermodynamic change of the cavern structure during the system operation.The air tightness model of compressed air storage energy caverns is then established.In the model,the permeability coefficient and air density of sealing layer vary with air pressure,and the effectiveness of the model is verified by field data in two test caverns.Finally,a compressed air storage energy cavern is taken as an example to understand the air tightness.The air leakage rate in the caverns is larger than that using air-pressure-independent permeability coefficient and air density,which is constant and small in the previous leakage rate calculation.Under the operating pressure of 4.5-10 MPa,the daily air leakage in the compressed air storage energy cavern of Yungang Mine with high polymer butyl rubber as the sealing material is 0.62%,which can meet the sealing requirements of compressed air storage energy caverns.The air tightness of the polymer sealing cavern is mainly affected by the cavern operating pressure,injected air temperature,cavern radius,and sealing layer thickness.The cavern air leakage rate will be decreased to reduce the cavern operating pressure the injection air temperature,or the cavern radius and sealing layer thickness will be increased.

Water, Air Emissions, and Cost Impacts of Air-Cooled Microturbines for Combined Cooling, Heating, and Power Systems： A Case Study in the Atlanta Region

城市化进程的加快意味着城市和国际组织需要去寻找各种能够提高能源效率和减少空气中污染物排放的方法。冷热电联产(CCHP)系统可以同时供暖、制冷和发电,具有提高城市或城市区域能源发电效率的潜力。本研究的目的是在满足建筑热需求(供热和制冷)的各种运行条件下,对亚特兰大大都市区内的五种常见建筑类型在采用CCHP系统时的发电耗水、CO_2和NO_x排放,及其经济性进行评价。对于大多数采用或不采用净计量策略的建筑类型来说,以满足每小时热需求去运行CCHP系统均可减少CO_2的排放量。该系统能否对这些建筑类型产生经济效益,主要取决于天然气的价格、净计量策略的采用和假定的CCHP系统的成本结构。当建筑物采用净计量策略并且CCHP系统是以满足建筑物每年的最大热需求而运行时,CCHP系统的发电耗水量和NO_x的排放量均有最大限度的减少,尽管此时该运行情景会增加温室气体排放和发电成本。CCHP系统对中型办公楼、大型办公楼和多户型住宅建筑更经济、实用。

Comparative Analysis of Diagonal and Centrifugal Compressors with Synergy Theory in Compressed Air Energy Storage System

Energy storage technology is an essential part of the efficient energy system.Compressed air energy storage(CAES)is considered to be one of the most promising large-scale physical energy storage technologies.It is favored because of its low-cost,long-life,environmentally friendly and low-carbon characteristics.The compressor is the core component of CAES,and the performance is critical to the overall system efficiency.That importance is not only reflected in the design point,but also in the continuous efficient operation under variable working conditions.The diagonal compressor is currently the focus of the developing large-scale CAES because of its stronger flow capacity compared with traditional centrifugal compressors.And the diagonal compressor has the higher single stage pressure ratio compared with axial compressors.In this paper,the full three dimensional numerical simulation technologies with synergy theory are used to compare and analyze the internal flow characteristics.The performance of the centrifugal and diagonal impellers that are optimized under the same requirements for large-scale CAES has been analyzed.The relationship between the internal flow characteristics and performance of the centrifugal and diagonal impellers with the change of mass flow rates and total inlet temperature is given qualitatively and quantitatively.Where the cosine value of the synergy angle is high,the local flow loss is large.The smaller proportion of the positive area is the pursuit of design.Through comparative analysis,it is concluded that the internal flow and performance changes of centrifugal and diagonal impellers are different.The results confirm the superiority and feasibility of the off-design performance of the diagonal compressor applied to the developing large-scale CAES.

Research on Storage Capacity of Compressed Air Pumped Hydro Energy Storage Equipment

Compressed air pumped hydro energy storage equipment combines compressed air energy storage technology and pumped storage technology. The water is pumped to a vessel to compress air for energy storage, and the compressed air expanses pushing water to drive the hydro turbine for power generation. The novel storage equipment saves natural gas resources, reduces carbon emission, and improves the controllability and reliability. The principle of compressed air pumped hydro energy storage is introduced and its mathematical model is built. The storage and generation process of the novel equipment is analyzed using the model. The calculation formula of the storage power is deduced in theory in different situations of isothermal and adiabatic compression. The optimal storage scheme is given when the capacity and withstand pressure of the vessel is definitive, and the max available capacity and the equipment utilization efficiency evaluation of the scheme is given.

Design issues for compressed air energy storage in sealed underground cavities

Compressed air energy storage （CAES） systems represent a new technology for storing very large amount of energy. A peculiarity of the systems is that gas must be stored under a high pressure （p - 10-30 MPa）. A lined rock cavern （LRC） in the form of a tunnel or shaft can be used within this pressure range. The rock mass surrounding the opening resists the internal pressure and the lining ensures gas tightness. The present paper investigates the key aspects of technical feasibility of shallow LRC tunnels or shafts under a wide range of geotechnical conditions. Results show that the safety with respect to uplift failure of the rock mass is a necessary but not a sufficient condition for assessing feasibility. The deformation of the rock mass should also be kept sufficiently small to preserve the integrity of the lining and, especially, its tightness. If the rock is not sufficiently stiff, buckling or fatigue failure of the steel lining becomes more decisive when evaluating the feasible operating air pressure. The design of the concrete plug that seals the compressed air stored in the container is another demanding task. Numerical analyses indicate that in most cases, the stability of the rock mass under the plug loading is not a decisive factor for plug design.

Operating performance of novel reverse-cycle defrosting method based on thermal energy storage for air source heat pump

To solve the fundamental problem of insufficient heat available during defrosting while ensuring the efficient and safe system operation for air-source heat pumps (ASHPs). A novel reverse-cycle defrosting (NRCD) method based on thermal energy storage to eliminate frost off the outdoor coil surface was developed. Comparative experiments using both the stand reverse cycle defrosting (SRCD) method and the NRCD method were carried out on an experimental ASHP unit with a nominal 2.5 kW heating capacity. The results indicate that during defrosting operation, using the NRCD method improves discharge and suction pressures by 0.24 MPa and 0.19 MPa, respectively, shortens defrosting duration by 60%, and reduces the defrosting energy consumption by 48.1% in the experimental environment, compared with those by the use of SRCD method. Therefore, using the NRCD method can shorten the defrosting duration, improve the indoor thermal comfort, and reduce the defrosting energy consumption in defrosting.

Performance Evaluation of Compressed Air Energy Storage Using TRNSYS

The appreciable economic growth in some of the developing countries like India in the recent years, towards providing energy security causes large environmental impact. Renewable Energy （RE） is being seen as one of the important means to meet the growing power needs of the economy while enhancing energy security and providing opportunities for mitigating greenhouse gas emissions. However, RE sources are highly intermittent in nature. The variability of these sources has led to concerns regarding the reliability of an electric grid that derives a large fraction of its energy from these sources as well as the cost of reliably integrating large amounts of variable generation into the electric grid. Hence at this juncture, it is necessary to explore the benefits of suitable Energy storage technologies. Compressed air energy storage （CAES） is a commercial, utility-scale technology that provides long-duration energy storage with fast ramp rates and good part-load operation. It is a promising storage technology for balancing the large-scale penetration of renewable energies, such as wind and solar power, into electric grids. Considering the potential of CAES storage, the present work, a thermodynamic model is developed with suitable assumptions and the simulation analysis is performed using transient system simulation （TRNSYS） v17 software. The system performanee is compared by considering the recovery during the heat of compression using a thermal storage system and without considering the heat recovery. The overall turnaround efficiency of the system without considering the thermal energy storage （TES） system is 57 % and with TES system the efficiency is increased to 70%.

Research on New Compressed Air Energy Storage Technology

In recent years, wind power generation and photovoltaic power generation have been developing rapidly, and the installed capacity of the new resources generation has been keeping a fast growth every year. But with the incorporation into the grid, the new resources generation that has the properties such as randomness and volatility causes certain risks to the power grid, which results in the falling of the incorporation proportion instead of rising. This paper describes the current status and development problems of the new energy in China, and gives a brief introduction of characteristics of various energy storage technologies. This paper focuses on the analysis of the compressed air energy storage technology in recent years and new developments and the latest technology at home and abroad, additionally, the paper introduces a new concept of the compressed air energy storage system.

Supercharging of Diesel Engine with Compressed Air: Experimental Investigation on Greenhouse Gases and Performance for a Hybrid Wind-Diesel System

Supercharging is the process of supplying air for combustion at a pressure greater than that achieved by natural or atmospheric induction, as applied to internal combustion engines. As a consequence of demonstrated technological, economical and energetic advantages in multiple literature evaluations concerning the large scale wind-compressed air hybrid storage system with gas turbines, the utilization of a hybrid wind-diesel system with compressed air storage (HWDCAS) has been frequently explored. These will mainly have average or small scale application such as the powering of isolated sites. It has been proven in numerous studies that the HWDCAS combined with an additional supercharging of the diesel engines will contribute to the increase of the power and efficiency of the diesel engine, the reduction of both fuel consumption and the emission of greenhouse gases (GHG). This article presents the obtained results from experimental validation of the selected design with an aim to valorize this innovative solution and become trustworthy.

Design Strategy of Diagonal Compressors in Compressed Air Energy Storage System

As a kind of large-scale physical energy storage,compressed air energy storage(CAES)plays an important role in the construction of more efficient energy system based on renewable energy in the future.Compared with traditional industrial compressors,the compressor of CAES has higher off-design performance requirements.From the perspective of design,it needs to pay attention not only to the performance of the design point,but also to the performance of all the stable working range.However,from the previous literature,no diagonal compressor was used in CAES which can meet the requirements,which also reflects the design program can be further improved.Therefore,this paper studies the design strategy of high efficient diagonal compressor for large-scale CAES,and gives the complete strategy algorithms used for different program modules.The pressure ratio,isentropic efficiency and stable working range are comprehensively considered.In the design process,the criteria for the key parameters of the diagonal flow angle of the diagonal compressor are given for the first time.The results show that the isentropic efficiency at the design point is 92.7%,the total pressure ratio is1.97,and the stable working range exceeds 20%,which meets the design requirements of the compressor for CAES and exceeds the overall performance of the previous compressors in the entire working range.

Increasing Coal-Fired Power Plant Operational Flexibility by Integrating Solar Thermal Energy and Compressed Air Energy Storage System

This paper proposed a novel integrated system with solar energy,thermal energy storage(TES),coal-fired power plant(CFPP),and compressed air energy storage(CAES)system to improve the operational flexibility of the CFPP.A portion of the solar energy is adopted for preheating the boiler’s feedwater,and another portion is stored in the TES for the CAES discharging process.Condensate water from the CFPP condenser is used for cooling compressed air during the CAES charging process.The thermodynamic performance of the integrated system under different load conditions is studied.The system operations in a typical day are simulated with EBSILON software.The system enables daily coal saving of 9.88 t and reduces CO_(2)emission by 27.95 t compared with the original CFPP at 100%load.Under partial load conditions,the system enables maximum coal saving of 10.29 t and maximum CO_(2)emission reduction of 29.11 t at 75%load.The system has maximum peak shaving depth of 9.42%under 40%load condition.The potential of the system participating ancillary service is also discussed.It is found that the integration of solar thermal system and CAES system can bring significant ancillary service revenue to a conventional CFPP.

Optimization of Operation Strategies for a Combined Cooling, Heating and Power System based on Adiabatic Compressed Air Energy Storage

The fluctuations of renewable energy and various energy demands are crucial issues for the optimal design and operation of combined cooling,heating and power(CCHP)system.In this paper,a novel CCHP system is simulated with advanced adiabatic compressed air energy storage(AA-CAES)technology as a join to connect with wind energy generation and an internal-combustion engine(ICE).The capital cost of utilities,energy cost,environmental protection cost and primary energy savings ratio(P E S R)are used as system performance indicators.To fulfill the cooling,heating and power requirements of a district and consider the thermal-electric coupling of ICE and AA-CAES in CCHP system,three operation strategies are established to schedule the dispatch of AA-CAES and ICE:ICE priority operation strategy,CAES priority operation strategy and simultaneous operation strategy.Each strategy leads the operation load of AA-CAES or ICE to improve the energy supply efficiency of the system.Moreover,to minimize comprehensive costs and maximize the P E S R,a novel optimization algorithm based on intelligent updating multi-objective differential evolution(MODE)is proposed to solve the optimization model.Considering the multi-interface characteristic and active management ability of the ICE and AA-CAES,the economic benefits and energy efficiency of the three operation strategies are compared by the simulation with the same system configuration.On a typical summer day,the simultaneous strategy is the best solution as the total cost is 3643 USD and the P E S R is 66.1%,while on a typical winter day,the ICE priority strategy is the best solution as the total cost is 4529 USD and the P E S R is 64.4%.The proposed methodology provides the CCHP based AA-CAES system with a better optimized operation.

A Novel Wind Energy Conversion System with Storage for Spillage Recovery

This paper proposes a new system configuration for integrating a compressed air energy storage system with a conventional wind turbine. The proposed system recycles the mechanical spillage of blades and stores it for later electricity generation with assistance from a rotary vane machine. The configuration and operational policy is explained, and a comparative case study shows that the proposed system recovers investment costs through savings on electricity procurement and revenue through power export.

Efficiency Analysis of an Arrayed Liquid Piston Isothermal Air Compression System for Compressed Air Energy Storage

Compressed air energy storage(CAES)is an important technology in the development of renewable energy.The main advantages of CAES are its high energy capacity and environmental friendliness.One of the main challenges is its low energy density,meaning a natural cavern is required for air storage.High-pressure air compression can effectively solve the problem.A liquid piston gas compressor facilitates high-pressure compression,and efficient convective heat transfer can significantly reduce the compression energy consumption during air compression.In this paper,a near isothermal compression method is proposed to increase the surface area and heat exchange by using multiple tube bundles in parallel in the compression chamber in order to obtain high-pressure air using liquid-driven compression.Air compression with a compression ratio of 6.25:1 is achieved by reducing the tube diameter and increasing the parallel tube number while keeping the compression chamber cross-sectional area constant in order to obtain a high-pressure air of 5 MPa.The performances of this system are analyzed when different numbers of tubes are applied.A system compression efficiency of 93.0%and an expansion efficiency of 92.9%can be achieved when 1000 tubes are applied at a 1 minute period.A new approach is provided in this study to achieve high efficiency and high pressure compressed air energy storage.