Urban Plant Biomass Residues from the Neotropics and Their Potential for Thermal Energy Generation

The material associated with tree pruning in a city in the Colombian neotropics was characterized in order to determine its energy potential.The species studied for their relevance in the territory were Prosopis juliflora,Licania tomentosa,Terminalia catappa,Azadirachta indica,Pithecellobium dulce,Ficus benjamina and Leucaena leucocephala.Moisture content,bulk density,hygroscopic response,elemental chemical analysis,proximal analysis,calorific value,ease of ignition and combustion,thermogravimetric and heat flow analysis,steam generation capacity,and qualitative analysis of gases(mass spectrometry)were determined.The results that were obtained show high initial moisture contents that vary between 37%and 67%and a variable density(when dry)between 0.21 and 0.41 g/cm3.Chemically,it was shown that all residues have lower carbon and sulfur content compared to a reference mineral coal.However,the residues of some species have higher nitrogen contents compared to the same coal.All biomasses are characterized by their high content of volatile fractions and by having a lower content of inorganic matter compared to carbon.The lower calorific values of these residues are between 14170 and 16928 kJ/kg,which are not negligible compared to other biomasses.This characteristic would be related to the high presence of hemicellulose in the residues.Flue gas monitoring revealed that there are different airflow needs in order to ensure complete combustion.Steam generation tests showed that the calorific value should not be the most relevant criterion to establish the potential use of the waste,since leucaena leucocephala,despite having the highest calorific value,was the material with the lowest performance in steam generation.

Fabrication of Fe–TiC–Al_2O_3 composites on the surface of steel using a TiO_2–Al–C–Fe combustion reaction induced by gas tungsten arc cladding

The aim of the present study was to fabricate Fe-TiC-Al2O3 composites on the surface of medium carbon steel.For this purpose,TiO2-3C and 3TiO2-4Al-3C-xFe（0 ≤ x ≤ 4.6 by mole） mixtures were pre-placed on the surface of a medium carbon steel plate.The mixtures and substrate were then melted using a gas tungsten arc cladding process.The results show that the martensite forms in the layer produced by the TiO2-3C mixture.However,ferrite-Fe3C-TiC phases are the main phases in the microstructure of the clad layer produced by the 3TiO2-4Al-3C mixture.The addition of Fe to the TiO2-4Al-3C reactants with the content from 0 to 20wt%increases the volume fraction of particles,and a composite containing approximately 9vol%TiC and A12O3 particles forms.This composite substantially improves the substrate hardness.The mechanism by which Fe particles enhance the TiC ＋ A12O3 volume fraction in the composite is determined.

MgO-based adsorbents for CO2 adsorption:Influence of structural and textural properties on the CO_2 adsorption performance

A series of MgO-based adsorbents were prepared through solution–combustion synthesis and ball-milling process.The prepared MgO-based powders were characterized using X-ray diffraction,scanning electron microscopy,N_2 physisorption measurements,and employed as potential adsorbents for CO_2 adsorption.The influence of structural and textural properties of these adsorbents over the CO_2 adsorption behaviour was also investigated.The results showed that MgO-based products prepared by solution–combustion and ball-milling processes,were highly porous,fluffy,nanocrystalline structures in nature,which are unique physico-chemical properties that significantly contribute to enhance their CO_2 adsorption.It was found that the MgO synthesized by solution combustion process,using a molar ratio of urea to magnesium nitrate（2：1）,and treated by ball-milling during 2.5 hr（MgO-BM2.5h）,exhibited the maximum CO_2 adsorption capacity of 1.611 mmol/g at 25℃ and 1 atm,mainly via chemisorption.The CO_2 adsorption behaviour on the MgO-based adsorbents was correlated to their improved specific surface area,total pore volume,pore size distribution and crystallinity.The reusability of synthesized MgO-BM2.5h was confirmed by five consecutive CO_2adsorption–desorption times,without any significant loss of performance,that supports the potential of MgO-based adsorbent.The results confirmed that the special features of MgO prepared by solution–combustion and treated by ball-milling during 2.5 hr are favorable to be used as effective MgO-based adsorbent in post-combustion CO_2 capture technologies.

Electrophoretic deposition and an investigation of co-dopants effect on luminescence property of Mg2SiO4:Eu3+phosphors

Forsterite particles doped with europium ions（Eu^（3＋）） were synthesized via a solution combustion method. The effect of co-dopants on photoluminescence intensity was described. Different percentages of calcium（Ca^（2＋））, zinc（Zn^（2＋））, barium（Ba^（2＋）） and strontium（Sr^（2＋）） were added to the Mg2SiO4：Eu^（3＋）host.The synthesized sample was characterized by X-ray diffraction, transmission electron microscopy,scanning electron microscopy, spectrofluorometer and the FTIR spectroscopy. X-ray diffraction（XRD）results revealed that dominant phase was forsterite in all samples. Additionally, a negligible amount of periclase phase was recognized in the samples. The average size of the synthesized particles was less than 200 nm. The presence of co-dopant led to an enhancement in the photoluminescent property of the synthesized samples. The maximum increase in photoluminescence intensity was obtained by Ba^（2＋）ions as a co-dopant. Condensed films of photoluminescence particles were produced by utilizing electrophoresis technique to deposit particles. The results showed that polyvinyl pyrrolidone was the best surface modifier to raise the mass deposition of the samples on the substrate.

Combustion synthesis of YAG:Ce phosphors via the thermite reaction of aluminum

Cerium-doped yttrium aluminum garnet（YAG：Ce） as a yellow phosphor for white light-emitting diodes（LEDs） was synthesized via a facile combustion method using Y2 O3, CeO2, Al2 O3, Al,and NaClO4 as raw materials. The combustion synthesis approach utilizes the strong exothermic oxidation of aluminum to realize a self-sustaining reaction. In this study, we investigated the effects of the ratios of Al2 O3 to AI,fluxes, and coprecipitated materials as raw materials on the luminescence properties of the synthesized YAG：Ce phosphors. When the amount of Al2 O3 x is varied, the combustion reaction proceeds at x ≤ 1.8,with x = 1.725 being the optimum condition for producing a high-performance product. When 5 wt%BaF2 is added, the luminescence intensity is significantly improved owing to a decrease of YAP（YAlO3）formation with improved uniformity. However, the addition of CaF2 and NaF does not improve the luminescence properties. To suppress the segregation of CeO2, we used the coprecipitated material Y2 O3-CeO2 as a raw material. Unlike with separate addition of Y2 O3 and CeO2, Ce ions are uniformly distributed in the coprecipitated material, resulting in improved luminescence properties. The combination of BaF2 and coprecipitated material significantly improves the internal quantum efficiency to83.0%, which is close to that of commercial phosphors.