Experimental investigation of combustion mechanisms of kerosene-fueled scramjet engines with double-cavity flameholders

A scramjet combustor with double cavitybased flameholders was experimentally studied in a directconnected test bed with the inflow conditions of M = 2.64,Pt = 1.84 MPa,Tt = 1 300 K.Successful ignition and selfsustained combustion with room temperature kerosene was achieved using pilot hydrogen,and kerosene was vertically injected into the combustor through 4×φ 0.5 mm holes mounted on the wall.For different equivalence ratios and different injection schemes with both tandem cavities and parallel cavities,flow fields were obtained and compared using a high speed camera and a Schlieren system.Results revealed that the combustor inside the flow field was greatly influenced by the cavity installation scheme,cavities in tandem easily to form a single side flame distribution,and cavities in parallel are more likely to form a joint flame,forming a choked combustion mode.The supersonic combustion flame was a kind of diffusion flame and there were two kinds of combustion modes.In the unchoked combustion mode,both subsonic and supersonic combustion regions existed.While in the choked mode,the combustion region was fully subsonic with strong shock propagating upstream.Results also showed that there was a balance point between the boundary separation and shock enhanced combustion,depending on the intensity of heat release.

Combustion Characteristics of Solid Sustained-Release Energetic Materials

A solid sustained-release energetic material sample,an eruption device and a complete test system were prepared further to analyse the combustion characteristics of solid sustainedrelease energetic materials.The high-temperature heat flux generated by the combustion of the samples from the eruption device was used to penetrate the Q235 target plate.In addition,the meaning and calculation formula of energy density characterising the all-around performance of heat flux were proposed.The numerical simulation of the combustion effect of samples was carried out.According to the data comparison,the numerical simulation results agreed with the experimental results,and the maximum deviation between the two was less than 8.9%.In addition,the structure of the combustion wave and high-temperature jet was proposed and analysed.Based on theoretical analysis,experimental research and numerical simulation,the theoretical burning rate formula of the sample was established.The maximum error between the theoretically calculated mass burning rate and the experimental results was less than 9.8%.Therefore,using the gas-phase steady-state combustion model to study the combustion characteristics of solid sustained-release energetic materials was reasonable.The theoretical burning rate formula also had high accuracy.Therefore,the model could provide scientific and academic guidance for the theoretical research,system design and practical application of solid sustained-release energetic materials in related fields.

Optimization of Combustion Characteristics and Fuel Injection Timing of a New Type Dual-Pit Combustor Rotary Engine

In order to improve the performance of the rotary engine,this paper has designed a new type of dual-pit rotary engine combustion chamber structure,and compares the combustion and emission characteristics with the rotary engine with a traditional combustion chamber.The existence of the dual-pit combustion chamber strengthens the overall vortex intensity in the cylinder,effectively promotes the mixing process of fuel and air in the cylinder,the maximum combustion pressure in the cylinder increased by 8.6%,significantly increases the diffusion combustion speed,and significantly improves the dynamic performance of the rotary engine.On this basis,the effects of fuel injection timing parameters on fuel distribution,combustion and emission characteristics were studied.Fuel distribution is more even and dispersed during injection in the later stage of compression.When the fuel injection timing was 105°BTDC in the middle of the compression phase,the matching effect of fuel distribution law and ignition scheme was the best.When the injection timing was 75°BTDC and 85°BTDC in the late compression stage,the mass fraction of NOx remained at a low level.The correlation between soot generation and the change of fuel injection timing was weak.When the injection time was 85°BTDC,the soot generation remained at a relatively high level.

Combustion Properties of Metal Particles as Components of Modified Double-Base Propellants

Metal particles such as aluminum（ Al）,magnesium（ Mg）,boron（ B） and nickel（ Ni）,as well as Mg/Al alloy（ Mg/Al = 3/4） are currently the most widely used ingredients in modified doublebase propellants. In this contribution,the combustion properties of the metal species are studied by means of the high-speed photography technique and the non-contact wavelet-based measurement of flame temperature distribution. The combustion process of the Al,Mg and Mg/Al samples shows both gas phase reaction and surface oxidation,which yield volatile and nonvolatile products,corresponding to the oxide and suboxide respectively. However,the combustion of B and Ni shows only gas phase reaction,due to their high melting point as well as high enthalpy of vaporization. In addition to the experiments,a hypothetical combustion model has been proposed to clarify the combustion characteristics of metal species in modified double-base propellants.