Transmission electron microscopy （TEM） and physics-chemical phase analysis were employed to investigate the precipitates in high strength steels microalloyed with Ti produced by compact strip production （CSP）. It ...Transmission electron microscopy （TEM） and physics-chemical phase analysis were employed to investigate the precipitates in high strength steels microalloyed with Ti produced by compact strip production （CSP）. It was seen that precipitates in Ti microalloyed steels mainly included TiN, Ti4C2S2, and TiC. The size of TiN particles varied from 50 to 500 nm, and they could precipitate during or before soaking. The Ti4C2S2 with the size of 40-100 nm might precipitate before rolling, and the TiC particles with the size of 5-50 nm precipitated heterogeneously. High Ti content would lead to the presence of bigger TiC particles that precipitated in austenite, and by contrast, TiC particles that precipitated in ferrite and the transformation of austenite to ferrite was smaller. They were less than 30 nm and mainly responsible for precipitate strengthening. It should be noted that the TiC particles in higher Ti content were generally smaller than those in the steel with a lower Ti content.展开更多
Large quantity of fine Ti（C,N） particles, 15-30 nm in size, were observed in low carbon hot strips added to a small amount of Ti and produced by CSP process. The results showed that the precipitation of Ti（C,N） mo...Large quantity of fine Ti（C,N） particles, 15-30 nm in size, were observed in low carbon hot strips added to a small amount of Ti and produced by CSP process. The results showed that the precipitation of Ti（C,N） mostly took place during soaking and hot rolling, which is significantly different from that in the conventional production. These fine Ti carbonitride particles could be very effective on the austenite grain refinement by hindering grain growth of recrystallized austenite. Their precipitation behavior was discussed and compared with that of the steels produced in the conventional production.展开更多
Cold-rolled steel sheets in automotive applications require an excellent deep draw ability, which is characterized by the Lankford value （r-value）. In this study, a correlation was identified between r-value and pan...Cold-rolled steel sheets in automotive applications require an excellent deep draw ability, which is characterized by the Lankford value （r-value）. In this study, a correlation was identified between r-value and pancake-shaped grain flatness which is indicated as the ratio of grain diameter in the rolling direction （RD） and normal direction （ND） of sheets （dr/dn）. A mathematical model （ r = e^0.345（dn^1/2-dr^1/2） ） was developed to calculate r-value by the microstructure of steel sheets hot-rolled by compact strip production （CSP）. It is shown that the r-value is higher, if the microstructure of steel sheet is of pancake-shaped grains elongated in the rolling direction. The calculated r-value is confirmed to fit exactly to the measured one from the large-scale production.展开更多
文摘Transmission electron microscopy （TEM） and physics-chemical phase analysis were employed to investigate the precipitates in high strength steels microalloyed with Ti produced by compact strip production （CSP）. It was seen that precipitates in Ti microalloyed steels mainly included TiN, Ti4C2S2, and TiC. The size of TiN particles varied from 50 to 500 nm, and they could precipitate during or before soaking. The Ti4C2S2 with the size of 40-100 nm might precipitate before rolling, and the TiC particles with the size of 5-50 nm precipitated heterogeneously. High Ti content would lead to the presence of bigger TiC particles that precipitated in austenite, and by contrast, TiC particles that precipitated in ferrite and the transformation of austenite to ferrite was smaller. They were less than 30 nm and mainly responsible for precipitate strengthening. It should be noted that the TiC particles in higher Ti content were generally smaller than those in the steel with a lower Ti content.
基金This work was financially supported by the National Natural Science Foundation of China (No.50371009)
文摘Large quantity of fine Ti（C,N） particles, 15-30 nm in size, were observed in low carbon hot strips added to a small amount of Ti and produced by CSP process. The results showed that the precipitation of Ti（C,N） mostly took place during soaking and hot rolling, which is significantly different from that in the conventional production. These fine Ti carbonitride particles could be very effective on the austenite grain refinement by hindering grain growth of recrystallized austenite. Their precipitation behavior was discussed and compared with that of the steels produced in the conventional production.
文摘Cold-rolled steel sheets in automotive applications require an excellent deep draw ability, which is characterized by the Lankford value （r-value）. In this study, a correlation was identified between r-value and pancake-shaped grain flatness which is indicated as the ratio of grain diameter in the rolling direction （RD） and normal direction （ND） of sheets （dr/dn）. A mathematical model （ r = e^0.345（dn^1/2-dr^1/2） ） was developed to calculate r-value by the microstructure of steel sheets hot-rolled by compact strip production （CSP）. It is shown that the r-value is higher, if the microstructure of steel sheet is of pancake-shaped grains elongated in the rolling direction. The calculated r-value is confirmed to fit exactly to the measured one from the large-scale production.
