Genesis Types and Diagenesis Compaction Mechanisms of Sandstone Rreservoirs in Dynamic Environments in Oil/Gas Basins in China

The diversity of sandstone diagenesis mechanisms caused by the complex geological conditions of oil/gas basins in China could hardly be reasonably explained by the traditional concept of burial diagenesis. Three genesis types of thermal diagenesis, tectonic diagenesis and fluid diagenesis are presented on the basis of the dynamic environment of the oil/gas basins and.the controlling factors and mechanisms of sandstone diagenesis. Thermal diagenesis of sandstone reservoirs is related not only to the effect of formation temperature on diagenesis, but also to the significant changes in diagenesis caused by geothermal gradients. The concept of thermal compaction is presented. Thermal compaction becomes weaker with increasing depth and becomes stronger at a higher geothermal gradient. At the same formation temperature, the sandstone porosity in the region with a lower geothermal gradient is e^0.077＋0.0042T times higher than that in the region with a higher geothermal gradient. Both sudden and gradual changes are observed in diagenetic evolution caused by structural deformation. Average sandstone compaction increased by 0.1051% for every 1.0MPa increase of lateral tectonic compressional stress, while late tectonic napping helped to preserve a higher porosity of underlying sandstone reservoir. Fluid diagenesis is a general phenomenon. The compaction caused by fluid properties is significant. The coarser the grain size, the stronger the fluid effect on compaction. The greater the burial depth, the weaker the fluid effect on compaction for the specific reservoir lithology and the greater the difference in the fluid effects on compaction between different grain sizes.

Influence of volume compression on the unloading deformation behavior of red sandstone under damage-controlled cyclic triaxial loading

A reasonable evaluation of unloading deformation characteristics is of great significance for the effective analysis of deformation and stability of surrounding rocks after underground excavation.In this study,the damage-controlled cyclic triaxial loading tests were conducted to investigate the pore compaction mechanism and its influences on the unloading deformation behavior of red sandstone,including Young’s modulus,Poisson’s ratio,volumetric strain,and irreversible strain.The experimental results show that the increases of volumetric and irreversible strains of rocks can be attributed to the compaction mechanism,which almost dominates the entire pre-peak deformation process.The unloading deformation consists of the reversible linear and nonlinear strains,and the irreversible strain under the influence of the porous grain structure.The pre-peak Young’s modulus tends to increase and then decrease due to the influence of the unloading irreversible strain.However,it hardly changes with the increasing volumetric strain compaction under the influence of reversible nonlinear strain.Instead,the initial unloading tangent modulus is highly related to the volumetric strain,and clearly reflects the compaction state of red sandstone.Furthermore,both the reversible nonlinear and irreversible unloading deformations are independent of confining pressure.This study is beneficial for the theoretical modeling and prediction of cyclic unloading deformation behavior of red sandstone.

Simulation and Analysis of Fiber Motion in Condensing Zone of Compact Spinning with Lattice Apron

To get fiber motion in condensing zone of compact spinning,velocity of this area is achieved by simulation,and then a bead-elastic rod fiber model is established.Based on simulation and dynamic analysis on this zone,governing equations are constructed and Runge-Kutta approach is used.Lastly,trajectories of fibers are calculated by specially designed Matlab procedure according to the principles mentioned above.Results show that fiber motions at different initial positions are different;X-axis velocity component makes fibers gathering on sides of suction slot;Y-axis airflow gets fibers gradually close and then stick to the surface of lattice apron.Fiber motions also reflect that the compact spinning process in condensing zone can be divided into three parts:fast convergence zone,adjustment convergence zone,and steady convergence zone.

Factors influencing physical property evolution in sandstone mechanical compaction:the evidence from diagenetic simulation experiments

In order to analyze the factors influencing sandstone mechanical compaction and its physical property evolution during compaction processes, simulation exper- iments on sandstone mechanical compaction were carried out with a self-designed diagenetic simulation system. The experimental materials were modem sediments from dif- ferent sources, and the experiments were conducted under high temperature and high pressure. Results of the exper- iments show a binary function relation between primary porosity and mean size as well as sorting. With increasing overburden pressure during mechanical compaction, the evolution of porosity and permeability can be divided into rapid compaction at an early stage and slow compaction at a late stage, and the dividing pressure value of the two stages is about 12 MPa and the corresponding depth is about 600 m. In the slow compaction stage, there is a good exponential relationship between porosity and overburden pressure, while a good power function relationship exists between permeability and overburden pressure. There is also a good exponential relationship between porosity and permeability. The influence of particle size on sandstone mechanical compaction is mainly reflected in the slowcompaction stage, and the influence of sorting is mainly reflected in the rapid compaction stage. Abnormally high pressure effectively inhibits sandstone mechanical com- paction, and its control on sandstone mechanical com- paction is stronger than that of particle size and sorting. The influence of burial time on sandstone mechanical compaction is mainly in the slow compaction stage, and the porosity reduction caused by compaction is mainly con- trolled by average particle size.

The Formula of Dependence of Mechanical Characteristics of Materials on Crystalline Phase Composition in the Matrix

Objective: For materials science and generally, for long-term operation of work-pieces in industry the significant role is attributed to dependence of macro-mechanical properties of consolidated body on crystalline phase composition, its dimensions, form, distribution in matrix and the form factor. While working in responsible fields of technology of ceramics and ceramic composites the above referred properties are attributed extremely great role with the view of durability and endurance at the terms of heavy mechanical loads. For description of the resistance of any concrete type work-piece, the crystalline phase plays the greatest role in mechanical strength or deformation of any material. It plays the important role in correlative explanation of materials mechanics and matrix properties. In our case, in the process of destruction of ceramic materials and composites, which will give us exhaustive response to the role of macro- and micro-mechanical properties of materials, the role of a macro- and micro-structural component, that is, of crystalline phase in the process of transition of stable state of materials into meta-stable state is extremely big. Our study aims to develop a formula of dependence of macro-mechanical properties of ceramic and ceramic composites on crystalline phase, the most powerful component of their structure, which will enable theorists and practitioners to select and develop technologies and technological processes correctly. Method: On the basis of the study of micro- and macro-mechanical properties of ceramics and ceramic composites and the morphology of crystalline phase and the analysis of the study we determined and created parameters of the formula. Results: The formula covers macro-mechanical properties, that is when the work-piece is thoroughly destructed: mechanic at bending at three and four-point load, mechanic at contraction;among morphological characteristics: composition of crystalline phase and their spreading in matrix, their sizes, form factor;correlative dependence of the above listed properties. Absolutely new definition of a factor of spreading of crystalline phase in matrix is offered. Conclusion: The created formula is of consolidated nature and it can be used in technology of any ceramic material and ceramic composites. The formula will help practitioners to plan correctly and fulfill accurately all positions of technology of production of work-pieces, to carry out the most responsible thermal treatment process of technology of manufacture of work-pieces;to determine correlation between mechanical and matrix properties of materials.

Impact of mechanical compaction on crop growth and sustainable agriculture

With the development of agricultural technology to meet the growing demands of a rapidly increasing population and economic development,intensive agriculture practices have been widely adopted globally. However,this intensification has resulted in adverse consequences for soil structure due to intensified farming activities and increased usage of heavy farm machinery.Of particular concern is soil compaction, which leads to the degradation of physical, chemical and biological properties of the soil. Soil compaction negatively impacts crop growth, reduces yields and poses a significant threat to food security and the overall sustainability of agricultural systems.Recognizing these challenges, this review aims to deepen understanding of the factors contributing to soil compaction and to develop effective mitigation strategies. By doing so, it is intended to attenuate the adverse impacts of soil compaction, improve soil structure, increase crop yield and ultimately enhance the sustainability of agricultural practices.