Towing characteristics of large-scale composite bucket foundation for offshore wind turbines

In order to study the towing dynamic properties of the large-scale composite bucket foundation the hydrodynamic software MOSES is used to simulate the dynamic motion of the foundation towed to the construction site.The MOSES model with the prototype size is established as the water draft of 5 and 6 m under the environmental conditions on site.The related factors such as towing force displacement towing accelerations in six degrees of freedom of the bucket foundation and air pressures inside the bucket are analyzed in detail.In addition the towing point and wave conditions are set as the critical factors to simulate the limit conditions of the stable dynamic characteristics.The results show that the large-scale composite bucket foundation with reasonable subdivisions inside the bucket has the satisfying floating stability.During the towing process the air pressures inside the bucket obviously change little and it is found that the towing point at the waterline is the most optimal choice.The characteristics of the foundation with the self-floating towing technique are competitive for saving lots of cost with few of the expensive types of equipment required during the towing transportation.

Failure Envelopes of Wide-Shallow Composite Bucket Foundation for Offshore Wind Turbines in Silty Sand

The wide-shallow composite bucket foundation(WSCBF) is a new type of offshore wind power foundation that can be built on land and rapidly installed offshore, there by effectively reducing the construction time and costs of offshore wind power foundation. In this study, the horizontal bearing capacity is calculated by finite element simulation and compared with test results to verify the validity of results. In this process, the vertical load and bending load are respectively calculated by the finite element simulation. Under the vertical load effect, the bucket foundation and the soil inside are regarded as a whole, and the corresponding buckling failure mode is obtained. The ultimate vertical bearing capacity is calculated using empirical and theoretical formulas; the theoretical formula is also revised by finite element results. Under bending load, the rotational center of the composite bucket foundation(in a region close to the bucket bottom) gradually moves from the left of the central axis(reverse to loading direction) to the nearby compartment boards along the loading direction. The H–M envelope line shows a linear relationship, and it is determined that the vertical and bending ultimate bearing capacities can be improved by an appropriate vertical load.

Load Transferring Mechanism on Transition Section of Composite Bucket Foundation for Offshore Wind Turbines

The composite bucket foundation (CBF) is a new kind of foundation which has been applied in the offshore wind industry. A reasonable connection pattern between the tower and the CBF top cover is crucial for load transmissions from the superstructure. Therefore, it is essential to choose an optimum structure type for the transition section. The line type and the arc transition section models were established by ABAQUS, and the internal forces of cross section were extracted along the height direction. Specifically, the force transfer mechanism for different types of the transition sections was investigated comparatively with monotonic as well as composite loadings. The results show that the curved transition structure exhibits the better mechanical characteristics under the monotonic and composite loadings, and the reason can be illustrated that its specific arc-shape structure can effectively convert the tremendous bending moment from the turbine tower into the limited tensile and compressive stresses downwards, without the occurrence of force concentration. © 2017, Tianjin University and Springer-Verlag Berlin Heidelberg.

Undrained Capacity of a Bucket Foundation with a Limited-Tension Interface for Offshore Wind Turbines

In this paper,the influence of the limited-tension interface between lid and soil on the undrained bearing capacity of the wide-shallow bucket foundation is examined by finite element(FE)analysis.The interface between the lid and the soil is modeled using a simplified approach called the surface-based cohesive behavior,with the aim of simulating the limited-tension interface.Initially,the interaction between the lid and the soil is explored under the zero-and unlimited-tension conditions by small-scale experiments.Afterward,the effects of the embedment ratio,soil strength heterogeneity,and lid-soil interface on the bearing capacity are outlined,and the failure mechanisms are explained by FE analysis.A modified closed-form formula is given to compute the moment bearing capacity with the limited-tension interface between the lid and the soil for different embedment ratios and soil strength heterogeneities.The numerical results reveal that the existing approximating solutions,which assume fully bonded interaction,accurately exhibit the shape of the normalized failure envelopes in hm and vh load space for the limited-tension interface.However,the shape of the vm envelopes differs,requiring a novel solution to estimate the combined bearing capacity of the bucket foundation based on the embedment ratio and soil strength heterogeneity with a zero-tension interface between the lid and the soil.

Bearing Capacity and Technical Advantages of Composite Bucket Foundation of Offshore Wind Turbines

Based on mechanical characteristics such as large vertical load, large horizontal load, large bending moment and complex geological conditions, a large scale composite bucket foundation （CBF） is put forward. Both the theoretical analysis and numerical simulation are employed to study the bearing capacity of CBF and the relationship between loads and ground deformation. Furthermore, monopile, high-rise pile cap, tripod and CBF designs are compared to analyze the bearing capacity and ground deformation, with a 3-MW wind generator as an example. The resuits indicate that CBF can effectively bear horizontal load and large bending moment resulting from upper structures and environmental load.

Design of Large-Scale Prestressing Bucket Foundation for Offshore Wind Turbines

The key in the force transmission between the tower and the foundation for offshore wind turbines is to transfer the large moment and horizontal loads. The finite element model of a large-scale prestressing bucket founda- tion for offshore wind turbines is set up and the structural characteristics of the arc transition structure of the founda- tion are analyzed for 40-60 channels(20-30 rows) arranged with prestressing steel strand under the same ultimate load and boundary conditions. The mechanical characteristics of the key parts of the foundation structures are illus- trated by the peak of the principal tensile stress, the peak of the principal compressive stress and the distribution areas where the principal tensile stress is larger than 2.00 MPa. It can be concluded that the maximum principal tensile stress of the arc transition decreases with the increasing number of channels, and the amplitude does not change signifi- cantly; the maximum principal compressive stress increases with the increasing number of channels and the amplitude changes significantly; however, for the distribution areas where the principal tensile stress is larger than 2.00 MPa, with different channel numbers, the phenomenon is not obvious. Furthermore, the principal tensile stress at the top of the foundation beams fluctuantly increases with the increasing number of channels and for the top cover of the bucket, the principal tensile stress decreases with the increasing number of channels.

Hydrodynamic Characteristics of Three-Bucket Jacket Foundation for Offshore Wind Turbines During the Lowering Process

The three-bucket jacket foundation is a new type of foundation for offshore wind turbine that has the advantages of fast construction speed and suitability for deep water. The study of the hoisting and launching process is of great significance to ensure construction safety in actual projects. In this paper, a new launching technology is proposed that is based on the foundation of the three-bucket jacket for offshore wind turbine. A complete time domain simulation of the launching process of three-bucket jacket foundation is carried out by a theoretical analysis combined with hydrodynamic software Moses. At the same time, the effects of different initial air storage and sea conditions on the motion response of the structure and the hoisting cable tension are studied. The results show that the motion response of the structure is the highest when it is lowered to 1.5 times the bucket height. The natural period of each degree of freedom of the structure increases with the increase of the lowering depth. The structural motion response and the hoisting cable tension vary greatly in the early phases of Stages Ⅰ and Ⅲ, smaller in Stage Ⅱ, and gradually stabilize in the middle and late phases of Stage Ⅲ.

Research on the Critical Buckling Pressure of Bucket Foundations with Inner Compartments for Offshore Wind Turbines

In the process of suction penetration of bucket foundations with inner compartments for offshore wind turbines,most researches focus on soil seepage failure and soil plugs,while the buckling of foundations is rarely investigated.Therefore,theoretical calculation methods for critical buckling pressures of the skirt and bulkheads of the bucket foundation are first presented according to the stability theory of a cylindrical shell and the small deflection theory of a thin plate,respectively.Furthermore,two types of models with and without considering the skirt-soil interaction are developed for the calculation of critical buckling pressure of the bucket foundation.Taking a practical project as an example,theoretical and numerical methods are used to obtain the critical buckling pressures of a bucket foundation.In this work,the theoretical method and the finite element model considering the skirt-soil interaction for calculating the critical buckling pressure of bucket foundations are firstly proposed.The results can help to optimize the design process of offshore wind turbine foundations and improve the safety of offshore wind power systems.

Experimental Study on the Sinking and Leveling of A Large-Capacity Offshore Wind Turbine Five-Bucket Foundation in Sand

As offshore wind farms expand into deeper and farther ocean regions and the unit capacity of offshore wind turbines(OWTs)increases,there is a pressing need for a new foundation structure that can accommodate deep-sea conditions and support large capacities while maintaining economical and safe.To meet this goal of integrated transportation and one-step installation,a novel five-bucket jacket foundation(FBJF),with its suction installation and leveling methods in sand,has been proposed,analyzed and experimentally studied.First,seepage failure experiments of the FBJF at various depths were conducted,and a formula for calculating the critical suction of seepage failure suitable for the FBJF in sand was chosen and recommended for use with a range of values for the permeability coefficient ratio.Second,through leveling experiments of the FBJF at different depths,the maximum adjustable leveling angle during the sinking process was defined using seepage failure and the adjustable leveling angle of the foundation as control criteria.Various leveling control strategies were proposed and verified.Finally,an automatic sinking and leveling control system for the FBJF was developed and experimentally verified for feasibility.

Experimental Investigation of Local Scour Around A New Pile-Group Foundation for Offshore Wind Turbines in Bi-Directional Current

The local scour around a new pile-group foundation of offshore wind turbine subjected to a bi-directional current was physically modeled with a bi-directional flow flume. In a series of experiments, the flow velocity and topography of the seabed were measured based on a system composed of plane positioning equipment and an ADV.Experimental results indicate that the development of the scour hole was fast at the beginning, but then the scour rate decreased until reaching equilibrium. Erosion would occur around each pile of the foundation. In most cases, the scour pits were connected in pairs and the outside widths of the scour holes were larger than the inner widths. The maximum scour depth occurred at the side pile of the foundation for each test. In addition, a preliminary investigation shows that the larger the flow velocity, the larger the scour hole dimensions but the shorter equilibrium time. The field maximum scour depth around the foundation was obtained based on the physical experiments with the geometric length scales of 1:27.0, 1:42.5 and 1:68.0, and it agrees with the scour depth estimated by the HEC-18 equation.

Influential Factors of Bucket Foundation for Offshore Wind Turbine

In this paper, the influential design thctors of wide-shallow composite bucket foundation for 3 MW off- shore wind turbine are systematically studied by numerical simulation. The results show that the bucket diameter is larger than 27 m in generak and the range of 7--12 m is appropriate for cylinder height. In particular the bucket foun- dation with diameter of 30 m and cylinder height of 10 m is suitable for most soils. Under ultimate loads, the bucket diameter and elasticity modulus of soil have major effects on the deibrmability of bucket foundation, while the influ- ence of friction coefficient between the bucket and soil is relatively slight.

Experimental Study on Tilt Adjustment Technique of Tripod Bucket Jacket Foundation for Offshore Wind Turbine in Sand

For the tripod bucket jacket foundations used in offshore wind turbines, the probable critical tilt angles should be avoidedduring tilt adjustment operation. Thus, these critical values must be identified by engineers, and remedial techniques mustbe established prior to the occurrence of the problem. Model tests were carried out for typical tilting conditions of tripodbucket foundations, which were allowed to tilt freely at various penetration depths without interruption by manualoperation. After the foundation ceased its tilting, some measures, such as water pumping, water injection, air injection, or acombination of the above methods, were enabled for adjustment. The research results showed two critical values in thetilting state of the tripod bucket jacket foundation, namely the terminal and allowable angles. In the installation condition,the terminal angle was negatively correlated with the initial penetration depth, but the opposite was observed with theremoval condition. The allowable angle was less than or equal to the terminal angle. The allowable angle in the installationwas related to the terminal angle. The critical angles all varied linearly with the initial penetration depth. When tiltingduring installation, adjustment measures can be used in the order of high drum pumping, low drum water injection, highdrum pumping and low drum water injection, air injection, and exhaust. When tilting during removal, the sequential use oflow drum water injection, air, and exhaust was applied. For buckets that were sensitive to angle changes, adjustmentmeasures of the “point injection” mode can be selected.

Application of Converted Displacement for Modal Parameter Identification of Offshore Wind Turbines with High-Pile Foundation

In the actual measurement of offshore wind turbines(OWTs),the measured accelerations usually contain a large amount of noise due to the complex and harsh marine environment,which is not conducive to the identification of structural modal parameters.For OWTs with remarkably low structural modal frequencies,displacements can effectively suppress the high-frequency vibration noise and amplify the low-frequency vibration of the structure.However,finding a reference point to measure structural displacements at sea is difficult.Therefore,only a few studies on the use of dynamic displacements to identify the modal parameters of OWTs with high-pile foundations are available.Hence,this paper develops a displacement conversion strategy to study the modal parameter identification of OWTs with high-pile foundations.The developed strategy can be divided into the following three parts:zero-order correction of measured acceleration,high-pass filtering by the Butterworth polynomial,and modal parameter identification using the calculated displacement.The superiority of the proposed strategy is verified by analyzing a numerical OWT with a high-pile foundation and the measured accelerations from an OWT with a high-pile foundation.The results show that for OWTs with high-pile foundations dominated by low frequencies,the developed strategy of converting accelerations into displacements and then performing modal parameter identification is advantageous to the identification of modal parameters,and the results have high accuracy.

Local Scour Mechanisms and Prediction Methods Around Offshore Wind Turbine Foundations:Insights and Future Directions

Local scour around offshore wind turbine foundations presents a considerable challenge due to its potential influence on structural stability,driven by hydrodynamic forces.While research has made strides in comprehending scouring mechanisms,notable complexities persist,specifically with newer foundation types.Addressing these limitations is vital for advancing our understanding of scour mechanisms and for improving mitigation strategies in offshore wind energy development.This review synthesizes current findings on local scour across various offshore foundations,encompassing field observations,data-driven approaches,turbulence-sediment interactions,scour evolution processes,influencing factors,and numerical model advancements.The objective is to enrich our understanding of local scour mechanisms.In addition,future research directions are outlined,including the development of robust arti-ficial intelligence models for accurate predictions,the exploration of vortex structure characteristics,and the refinement of numerical models to strengthen prediction capabilities while minimizing computational efforts.

Motion Characteristics of Novel Floating Foundation for Offshore Wind Turbine

A novel floating foundation to support the NREL offshore 5 MW wind turbine was designed conceptually by combining the characteristics of barge and Spar. The main focus was structural design and hydrodynamic modelling. Based on this novel floating foundation, the hydrodynamic performance was investigated in the frequency domain and time domain by using the wave analysis software Hydro D and Deep C from Det Norske Veritas. The frequency domain analysis was conducted to investigate the effects of the incident wave angle and water depth. The time-domain analysis was carried out to evaluate the response of the floating foundation under a selected operational condition. The hydrodynamic performances of this floating foundation with respect to time series and response spectra were also investigated in this study.

Numerical Analysis of a Gravity Substructure for 5 MW Offshore Wind Turbines Due to Soil Conditions

In order to increase the gross generation of wind turbines, the size of a tower and a rotor-nacelle becomes larger. In other words, the substructure for offshore wind turbines is strongly influenced by the effect of wave forces as the size of substructure increases. In addition, since a large offshore wind turbine has a heavy dead load, the reaction forces on the substructure become severe, thus very firm foundations should be required. Therefore, the dynamic soil-structure interaction has to be fully considered and the wave forces acting on substructure accurately calculated. In the present study, ANSYS AQWA is used to evaluate the wave forces. Moreover, the substructure method is applied to evaluate the effect of soil-structure interaction. Using the wave forces and the stiffness and damping matrices obtained from this study, the structural analysis of the gravity substructure is carried out through ANSYS mechanical. The structural behaviors of the strength and deformation are evaluated to investigate an ultimate structural safety and serviceability of gravity substructure for various soil conditions. Also, the modal analysis is carried out to investigate the resonance between the wind turbine and the gravity substructure.

Experiment Study of Dynamics Response for Wind Turbine System of Floating Foundation

The floating foundation is designed to support a 1.5 MW wind turbine in 30 m water depth. With consideration of the viscous damping of foundation and heave plates, the amplitude-frequency response characteristics of the foundation are studied. By taking into account the elastic effect of blades and tower, the classic quasi-steady blade-element/momentum（BEM） theory is used to calculate the aerodynamic elastic loads. A coupled dynamic model of the turbine-foundationmooring lines is established to calculate the motion response of floating foundation under Kaimal wind spectrum and regular wave by using the FAST codes. The model experiment is carried out to test damping characteristics and natural motion behaviors of the wind turbine system. The dynamics response is tested by considering only waves and the joint action of wind and waves. It is shown that the wind turbine system can avoid resonances under the action of wind and waves. In addition, the heave motion of the floating foundation is induced by waves and the surge motion is induced by wind. The action of wind and waves is of significance for pitch.

A simplified method for analyzing the fundamental frequency of monopile supported offshore wind turbine system design

Preliminary design of offshore wind turbines requires high precision simplified methods for the analysis of the system fundamental frequency. Based on the Rayleigh method and Lagrange’s Equation, this study establishes a simple formula for the analysis of system fundamental frequency in the preliminary design of an offshore wind turbine with a monopile foundation. This method takes into consideration the variation of cross-section geometry of the wind turbine tower along its length, with the inertia moment and distributed mass both changing with diameter. Also the rotational flexibility of the monopile foundation is mainly considered. The rigid pile and elastic middle long pile are calculated separately. The method is validated against both FEM analysis cases and field measurements, showing good agreement. The method is then used in a parametric study, showing that the tower length Lt, tower base diameter d0, tower wall thickness δt, pile diameter db and pile length Lb are the major factors influencing the fundamental frequency of the offshore wind turbine system. In the design of offshore wind turbine systems, these five parameters should be adjusted comprehensively. The seabed soil condition also needs to be carefully considered for soft clay and loose sand.

Seismic Centrifuge Modelling of Offshore Wind Turbine with Tripod Foundation

The development of offshore wind energy is fast as it is clean, safe and of high efficiency. The harsh marine environment raises high demand on the foundation design of offshore wind turbine. Earthquake loading is one of the most significant factors which should be considered in the design phase. In this paper, a group of earthquake centrifuge tests were conducted on a physical wind turbine model with tripod foundation. The seismic responses of both wind turbine model and foundation soil were analyzed in terms of the recorded accelerations, pore water pressures, lateral displacements and settlements. The results were also compared with those measured in the previous research on mono-pile foundation. It is demonstrated that the tripod foundation can provide better resistance in the lateral displacement and structural settlement under earthquake loading.

Seismic Behavior of Offshore Wind Turbine with Gravity Foundation

The development of offshore wind energy becomes very fast in recent years due to its clean, safe, and high efficiency. However, the issue that quite a few offshore wind farms have been built in seismic active areas raises a great engineering challenge for the selection, design, and seismic evaluation of offshore wind turbine foundations. Earthquake is one of the most critical hazards for offshore wind turbines. The softening of soil due to pore water pressure buildup can sharply reduce the bearing capacity of the foundation, and consequently result in stability failure. The induced strong structural vibration has adverse impact on the normal operation of wind turbine as well as on the efficiency of power generation. In this study, a group of earthquake centrifuge tests was performed on a physical model of a wind turbine with gravity foundation. The seismic behavior of both the structure and the foundation soil was analyzed based on the recorded accelerations, pore water pressures, lateral displacements and settlements. The emphasis was on the interaction between foundation and soil. The results showed that gravity foundation can effectively resist the overturning moment induced by the superstructure. However, it was quite sensitive to the subsoil conditions. The large settlement and tilt in the offshore foundation might affect the performance of a wind turbine.