Experiments were carried out to design polyvinyl alcohol （PVA） fiber reinforced cementitous composites （PVA-FRCCs） holding high ductility and energy consumption ability. Besides, the properties of each ingredients...Experiments were carried out to design polyvinyl alcohol （PVA） fiber reinforced cementitous composites （PVA-FRCCs） holding high ductility and energy consumption ability. Besides, the properties of each ingredients in composites, mixing method and technology for fresh mixture were described in detail. Then, the pseudo-strain-hardening （PSH） behavior was investigated in uniaxial tension test. As a result, the maximum ultimate tensile strain can reach 0.7 percent. On the other hand, the single edge notch （SEN） thin sheet specimens were employed to gain the normal tensile load via crack mouth opening displacement （CMOD） curves, which can show obvious PSH behavior. In addition, the curves can be divided into four zones whose fracture toughness calculation methods were discussed. The wedge splitting （WS） test method can be applied to discuss the fracture toughness. Moreover, fracture energy of SEN and WS specimens were both approximately evaluated.展开更多
Using polysulfone （PSF） hollow fiber ultrafiltration membranes as the substrate, sodium alginate （SA） and polyvinyl alcohol （PVA） blend solutions as the coating solution, and maleic anhydride （MAC） as the cros...Using polysulfone （PSF） hollow fiber ultrafiltration membranes as the substrate, sodium alginate （SA） and polyvinyl alcohol （PVA） blend solutions as the coating solution, and maleic anhydride （MAC） as the cross-linked agent, SAPVA/PSF hollow fiber composite membranes were prepared for the dehydration of ethanol-water. The effects of different sodium alginate concentration in the coating solutions and different operating temperatures on pervaporation performance were investigated. The experimental results showed that pervaporation performance of the SA-PVA/PSF composite membranes for ethanol-water solution exhibited a high separation factor although they had a relatively low permeation flux. As SA concentration in SA-PVA coating solution was 66.7% and the operating temperature was 40 ℃, SA-PVA/PSF hollow fiber composite membrane （PS4） had a separation factor of 886 and flux of 12.6 g/（m^2·h）. Besides, SA-PVA/PSF hollow fiber composite membranes （PS3 and PS4） were used for the investigation of the effect of ethanol concentration in the feed solution on pervaporation performance.展开更多
In this paper, we deals with mechanical performance of resin impregnation with natural fiber and fiber reinforced composites. The effect of the addition of a rein impregnation process on static strength of the injecti...In this paper, we deals with mechanical performance of resin impregnation with natural fiber and fiber reinforced composites. The effect of the addition of a rein impregnation process on static strength of the injection molded composites was investigated by carrying out tensile and banding tests, followed by Scanning electron microscopy (SEM) observation of fiber surface and fracture surface of composites. The tensile strength of natural fiber and natural fiber reinforced composites with resin impregnation method increases with Polyvinyl alcohol (PVA) impregnation. In addition, Phenol resin impregnation recovers fiber tensile strength after alkali treatment. Resin impregnation causes decrease in contact surface area;however, it does not cause decrease in mechanical properties. Our results suggest that the using rein impregnation method has better effect on the mechanical properties of natural fiber reinforced Polypropylene (PP) composites.展开更多
Previously, Polyvinyl Alcohol (PVA) and phenolic resin were used for resin impregnated bamboo fiber reinforced PP composites which was manufactures for resin impregnated bamboo fiber with polypropylene (PP). Resin imp...Previously, Polyvinyl Alcohol (PVA) and phenolic resin were used for resin impregnated bamboo fiber reinforced PP composites which was manufactures for resin impregnated bamboo fiber with polypropylene (PP). Resin impregnation method can show improvement on tensile strength of fiber. However, to reduce the contact surface area and low inter-facial shear strength (IFSS) between impregnated resin and matrix, using 40% weight fraction of bamboo fiber in PP matrix, PVA impregnated composites with mean flexural and tensile strength 10% higher than untreated composites were produced butphenolic resin impregnated fiber reinforced composition’s mechanical properties were decreased. In this study maleic anhydride grafted polypropylene (MAPP) was used to increase interfacial shear strength between resin impregnated fiber and PP. With 10% MAPP, IFSS between resin impregnated fiber and PP increased more than 100% and reinforced composites. MAPP with untreated, phenolic resin and PVA impregnated cases showed similar mechanical properties. Yet in water absorption test, the PVA treatment with bamboo/PP composites increased water absorption ratio. But with 10% MAPP, matrix PP water absorption ratio decreased like phenolic resin impregnated fiber reinforced composites. 10% MAPP with resin impregnated bamboo fiber reinforced PP composites can improve IFSS, mechanical properties of composite and can decrease water absorption PVA resin impregnated bamboo fiber reinforced composites.展开更多
为提高海藻酸钠/南极磷虾蛋白(SA/AKP)复合纤维的强度,采用聚乙烯醇(PVA)共混改性,并用湿法纺丝制备改性海藻酸钠纤维。通过傅里叶变换红外光谱研究了复合纤维基本结构,并用二阶导数和高斯拟合分峰表征复合体系中氢键的作用,同时分析了...为提高海藻酸钠/南极磷虾蛋白(SA/AKP)复合纤维的强度,采用聚乙烯醇(PVA)共混改性,并用湿法纺丝制备改性海藻酸钠纤维。通过傅里叶变换红外光谱研究了复合纤维基本结构,并用二阶导数和高斯拟合分峰表征复合体系中氢键的作用,同时分析了改性后复合纤维表面形貌、结晶性能、力学性能。结果表明,SA/AKP/PVA复合体系中氢键的类型和含量,随PVA增多自由羟基的数量由1.2%增加到3.6%,分子间氢键数量由57.8%减少到54.8%,而体系分子内氢键数量几乎没有变化。复合纤维表面沟槽变细且分布更加均匀。随PVA含量的增加,复合纤维的结晶度降低,力学性能呈先增后减的趋势,当PVA含量为3.5%时,其断裂强度达到最大值2.43 c N/dtex。展开更多
基金Committee on Science and Technology Foundation of China(No.50438010)The Research of Formation Progress and Control Technology of Concrete Structure Cracks
文摘Experiments were carried out to design polyvinyl alcohol （PVA） fiber reinforced cementitous composites （PVA-FRCCs） holding high ductility and energy consumption ability. Besides, the properties of each ingredients in composites, mixing method and technology for fresh mixture were described in detail. Then, the pseudo-strain-hardening （PSH） behavior was investigated in uniaxial tension test. As a result, the maximum ultimate tensile strain can reach 0.7 percent. On the other hand, the single edge notch （SEN） thin sheet specimens were employed to gain the normal tensile load via crack mouth opening displacement （CMOD） curves, which can show obvious PSH behavior. In addition, the curves can be divided into four zones whose fracture toughness calculation methods were discussed. The wedge splitting （WS） test method can be applied to discuss the fracture toughness. Moreover, fracture energy of SEN and WS specimens were both approximately evaluated.
基金Project supported by the National Basic Research Program of China (Grant No.2003CB615705)
文摘Using polysulfone （PSF） hollow fiber ultrafiltration membranes as the substrate, sodium alginate （SA） and polyvinyl alcohol （PVA） blend solutions as the coating solution, and maleic anhydride （MAC） as the cross-linked agent, SAPVA/PSF hollow fiber composite membranes were prepared for the dehydration of ethanol-water. The effects of different sodium alginate concentration in the coating solutions and different operating temperatures on pervaporation performance were investigated. The experimental results showed that pervaporation performance of the SA-PVA/PSF composite membranes for ethanol-water solution exhibited a high separation factor although they had a relatively low permeation flux. As SA concentration in SA-PVA coating solution was 66.7% and the operating temperature was 40 ℃, SA-PVA/PSF hollow fiber composite membrane （PS4） had a separation factor of 886 and flux of 12.6 g/（m^2·h）. Besides, SA-PVA/PSF hollow fiber composite membranes （PS3 and PS4） were used for the investigation of the effect of ethanol concentration in the feed solution on pervaporation performance.
文摘In this paper, we deals with mechanical performance of resin impregnation with natural fiber and fiber reinforced composites. The effect of the addition of a rein impregnation process on static strength of the injection molded composites was investigated by carrying out tensile and banding tests, followed by Scanning electron microscopy (SEM) observation of fiber surface and fracture surface of composites. The tensile strength of natural fiber and natural fiber reinforced composites with resin impregnation method increases with Polyvinyl alcohol (PVA) impregnation. In addition, Phenol resin impregnation recovers fiber tensile strength after alkali treatment. Resin impregnation causes decrease in contact surface area;however, it does not cause decrease in mechanical properties. Our results suggest that the using rein impregnation method has better effect on the mechanical properties of natural fiber reinforced Polypropylene (PP) composites.
文摘Previously, Polyvinyl Alcohol (PVA) and phenolic resin were used for resin impregnated bamboo fiber reinforced PP composites which was manufactures for resin impregnated bamboo fiber with polypropylene (PP). Resin impregnation method can show improvement on tensile strength of fiber. However, to reduce the contact surface area and low inter-facial shear strength (IFSS) between impregnated resin and matrix, using 40% weight fraction of bamboo fiber in PP matrix, PVA impregnated composites with mean flexural and tensile strength 10% higher than untreated composites were produced butphenolic resin impregnated fiber reinforced composition’s mechanical properties were decreased. In this study maleic anhydride grafted polypropylene (MAPP) was used to increase interfacial shear strength between resin impregnated fiber and PP. With 10% MAPP, IFSS between resin impregnated fiber and PP increased more than 100% and reinforced composites. MAPP with untreated, phenolic resin and PVA impregnated cases showed similar mechanical properties. Yet in water absorption test, the PVA treatment with bamboo/PP composites increased water absorption ratio. But with 10% MAPP, matrix PP water absorption ratio decreased like phenolic resin impregnated fiber reinforced composites. 10% MAPP with resin impregnated bamboo fiber reinforced PP composites can improve IFSS, mechanical properties of composite and can decrease water absorption PVA resin impregnated bamboo fiber reinforced composites.
文摘为提高海藻酸钠/南极磷虾蛋白(SA/AKP)复合纤维的强度,采用聚乙烯醇(PVA)共混改性,并用湿法纺丝制备改性海藻酸钠纤维。通过傅里叶变换红外光谱研究了复合纤维基本结构,并用二阶导数和高斯拟合分峰表征复合体系中氢键的作用,同时分析了改性后复合纤维表面形貌、结晶性能、力学性能。结果表明,SA/AKP/PVA复合体系中氢键的类型和含量,随PVA增多自由羟基的数量由1.2%增加到3.6%,分子间氢键数量由57.8%减少到54.8%,而体系分子内氢键数量几乎没有变化。复合纤维表面沟槽变细且分布更加均匀。随PVA含量的增加,复合纤维的结晶度降低,力学性能呈先增后减的趋势,当PVA含量为3.5%时,其断裂强度达到最大值2.43 c N/dtex。
