Study on T700/Cyanate/PS/Epoxy Composites with ex-situ Toughening Technique

Composites were prepared with polysulfone through ex-situ toughening technique. The dynamic parameters of cyanate/epoxy resin were studied by differential scanning calorimetric（DSC） analysis and dynamic mechanical analysis（DMA）. Microstructual toughening mechanism was studied through scanning electron microscopy（SEM）. The particle microstructure in interlaminar region of composites toughened through ex-situ toughening technique revealed that a reaction induced phase decomposition and phase inversion happened in the interlaminar region. The thermosetting particles were surrounded by the PS phase, which could signifi cantly improve the delamination resistance of composites. The compression after impact（CAI） can be signifi cantly improved from 180 MPa to 260 MPa by using ex-situ toughening while the mechanical properties are not affected.

Synthesis and electrochemical properties of LiMn_2O_4/Li_4Ti_5O_(12) composite

LiMn2O4/Li4Ti5O12 composite was synthesized by in-situ composite technique using LiMn2O4,lithium acetate,tetrabutyl titanate as starting materials and characterized by various electrochemical methods in combination with X-ray diffractometry(XRD), infrared(IR)spectroscopy and scanning electron microscopy(SEM).The results show that Li4Ti5O12 is coated on the surface of crystalline LiMn2O4 to form LiMn2O4/Li4Ti5O12 composite.The structure of LiMn2O4 does not change due to the introduction of Li4Ti5O12.By being coated with Li4Ti5O12,the rate capability and high temperature cyclability of LiMn2O4 is improved greatly.At room temperature,the discharge capacity of LiMn2O4/Li4Ti5O12 composite is more than 108.4 mA·h/g and the capacity loss per cycle is only 0.053%after 20 cycles at 2.0C.While at 55℃,the discharge capacity of LiMn2O4/Li4Ti5O12 composite is more than 109.9 mA·h/g and the capacity loss per cycle is only 0.036%after 60 cycles at 1.0C.

Experimental study and analysis on fatigue stiffness of RC beams strengthened with CFRP and steel plate

The objective of this work is to investigate the fatigue behavior of reinforced concrete(RC) beams strengthened with externally bonded carbon fiber reinforced polymer(CFRP) and steel plate. An experimental investigation and theoretical analysis were made on the law of deflection development and stiffness degradation, as well as the influence of fatigue load ranges. Test results indicate that the law of three-stage change under fatigue loading is followed by both midspan deflection and permanent deflection, which also have positive correlation with fatigue load amplitude. Fatigue stiffness of composite strengthened beams degrades gradually with the increasing of number of cycles. Based on the experimental results, a theoretical model by effective moment of inertia method is developed for calculating the sectional stiffness of such composite strengthened beams under fatigue loading, and the calculated results are in good agreement with the experimental results.

Global Mg/Si and Al/Si Distributions on the Lunar Surface Derived from Chang'E-2 X-ray Spectrometer

The technique of X-ray fluorescence remote sensing plays a significant role in research related to the chemical compositions of the Moon. Here we describe the data analysis method for China＇s Chang＇E-2 X-ray spectrometer in detail and present the preliminary results about the first global Mg/Si and Al/Si maps of the lunar surface. Our results show that the distributions of Mg/Si and Al/Si correlate well with terrains on the Moon. The higher Mg/Si ratio corresponds to the mare regions while the lower value corresponds to the highland terrains. The map of the Al/Si ratio shows a reversed distribution compared with the map of the Mg/Si ratio.

Elastic deformation behavior of CuZrAlNb metallic glass matrix composites with different crystallization degrees

The room temperature brittleness has been a long standing problem in bulk metallic glasses realm.This has seriously limited the application potential of metallic glasses and their composites.The elastic deformation behaviors of metallic glass matrix composites are closely related to their plastic deformation states.The elastic deformation behaviors of Cu48-xZr48Al4Nbx（x=0,3at.%）metallic glass matrix composites（MGMCs）with different crystallization degrees were investigated using an in-situ digital image correlation（DIC）technique during tensile process.With decreasing crystallization degree,MGMC exhibits obvious elastic deformation ability and an increased tensile fracture strength.The notable tensile elasticity is attributed to the larger shear strain heterogeneity emerging on the surface of the sample.This finding has implications for the development of MGMCs with excellent tensile properties.

Theoretical Approach to Change Blast Furnace Regime With Natural Gas Injection

The operation of blast furnace using natural gas and oxygen enriched blast （composite blast technology） is considered in many countries to be standard operation for a modern blast furnace particularly in certain countries with cheap and stable supply of natural gas. The theoretical flame temperature （TFT） of combustion and the degree of di-rect reduction of iron oxides （rd） are considered as the main controlling parameters of composite blast technology. The calculated values of these parameters are mainly dependent on the amount of air blast consumption. This amount of air blast is measured before entering into blast stoves, Actually, some of air blast is lost through valves of air stoves. Consequently, the real volume of air blast in the furnace is less than the recorded value by amounts of 5%-15% which is not considered in the estimation of rd and TFT. The purpose is to analyze the different methods for es-timation of air blast inside the blast furnaces and develop a theoretical model to calculate air blast eonsumption with high accuracy. Based on the calculation of air blast consumption, a complete roadmap is demonstrated to change the operation regime parameters of blast furnaces working on composite blast technology.

Determination of microcapsule physicochemical, structural, and mechanical properties

Research into the fundamental properties of microcapsules and use of the results to develop a wide variety of products in industries such as printing, fast-moving consumer goods, construction, pharmaceuticals, and agrochemicals is a dynamic and ever-progressing field of study. For microcapsules to be effective in providing protection from harsh environments or delivering large payloads, it is essential to have a good understanding of their properties to enable quality control during formulation, storage, and applications. This review aims to outline the commonly used techniques for determining the physicochemical, struc- tural, and mechanical properties of microcapsules, and highlights the interlinked nature of these three areas with respect to the end-use industrial application. This review provides information on techniques that are well supported in the literature, and also examines microcapsule analytical techniques that will become more prevalent as a result of new technological developments or extensions from other areas of study.