Synthesis and Characterization of Biomimetic Fe3O4/Coke Magnetic Nanoparticles Composite Material

A composite material（Fe3O4/Coke）using coke supported Fe3O4 magnetic nanoparticles was successfully prepared via an in-situ chemicaloxidation precipitation method and characterized by SEM,XRD,Raman,and FTIR.The results showed that the Fe3O4 nanoparticles existed steadily on the surface of coke,with better dispersing and smaller particle size.The catalytic ability of Fe3O4/Coke were investigatied by degrading p-nitrophenol（P-NP）.The results showed that the apparent rate constant for the P-NP at 1.0 g·L^-1 catalyst,30 mmol·L^-1 H2O2,pH=3.0,30 ℃ and the best ratio of Coke/Fe3O4 0.6,was evaluated to be 0.027 min^-1,the removalrate of CODCr was 75.47%,and the dissolubility of Fe was 2.42 mg·L^-1.Compared with pure Fe3O4,the catalytic ability of Fe3O4/Coke in the presence of H2O2 was greatly enhanced.And Fe3O4/Coke was a green and environmentalcatalyst with high catalytic activity,showing a good chemicalstability and reusability.

Ultralow detection limit of giant magnetoresistance biosensor using Fe3O4–graphene composite nanoparticle label

A special Fe3O4nanoparticles–graphene（Fe3O4–GN） composite as a magnetic label was employed for biodetection using giant magnetoresistance（GMR） sensors with a Wheatstone bridge. The Fe3O4–GN composite exhibits a strong ferromagnetic behavior with the saturation magnetization MS of approximately 48 emu/g, coercivity HC of 200 Oe, and remanence Mr of 8.3 emu/g, leading to a large magnetic fringing field. However, the Fe3O4 nanoparticles do not aggregate together, which can be attributed to the pinning and separating effects of graphene sheet to the magnetic particles. The Fe3O4–GN composite is especially suitable for biodetection as a promising magnetic label since it combines two advantages of large fringing field and no aggregation. As a result, the concentration x dependence of voltage difference ｜？V｜ between detecting and reference sensors undergoes the relationship of ｜？V｜ = 240.5 lgx ＋ 515.2 with an ultralow detection limit of 10 ng/mL（very close to the calculated limit of 7 ng/mL） and a wide detection range of 4 orders.

Synthesis of Y_2O_3 particle enhanced Ni/TiC composite on TC4 Ti alloy by laser cladding

A Y2O3 particle enhanced Ni/TiC composite coating was fabricated in-situ on a TC4 Ti alloy by laser surface cladding. The phase component, microstructure, composition distribution and properties of the composite layer were investigated. The composite layer has graded microstructures and compositions, due to the fast melting followed by rapid solidification and cooling during laser cladding. The TiC powders are completely dissolved into the melted layer during melting and segregated as fine dendrites when solidified. The size of TiC dendrites decreases with increasing depth. Y2O3 fine particles distribute in the whole clad layer. The Y2O3 particle enhanced Ni/TiC composite layer has a quite uniform hardness along depth with a maximum value of HV1380, which is 4 times higher than the initial hardness. The wear resistance of the Ti alloy is significantly improved after laser cladding due to the high hardness of the composite coating.

Heterogeneous catalytic activation of peroxymonosulfate for efficient degradation of organic pollutants by magnetic Cu^0/Fe_3O_4 submicron composites

Magnetic Cu^0/Fe3O4 submicron composites were prepared using a hydrothermal method and used as heterogeneous catalysts for the activation of peroxymonosulfate（PMS） and the degradation of organic pollutants.The as-prepared magnetic Cu^0/Fe3O4 submicron composites were composed of Cu^0 and Fe3O4 crystals and had an average size of approximately 220 nm.The Cu^0/Fe3O4 composites could efficiently catalyze the activation of PMS to generate singlet oxygen,and thus induced the rapid degradation of rhodamine B,methylene blue,orange Ⅱ,phenol and 4-chlorophenol.The use of0.1 g/L of the Cu^0/Fe3O4 composites induced the complete removal of rhodamine B（20 μmol/L） in15 min,methylene blue（20 μmol/L） in 5 min,orange Ⅱ（20 μmol/L） in 10 min,phenol（0.1mmol/L） in 30 min and 4-chlorophenol（0.1 mmol/L） in 15 min with an initial pH value of 7.0 and a PMS concentration of 0.5 mmol/L.The total organic carbon（TOC） removal higher than 85%for all of these five pollutants was obtained in 30 min when the PMS concentration was 2.5 mmol/L.The rate of degradation was considerably higher than that obtained with Cu^0 or Fe3O4 particles alone.The enhanced catalytic activity of the Cu^0/Fe3O4 composites in the activation of PMS was attributed to the synergistic effect of the Cu^0 and Fe3O4 crystals in the composites.Singlet oxygen was identified as the primary reactive oxygen species responsible for pollutant degradation by electron spin resonance and radical quenching experiments.A possible mechanism for the activation of PMS by Cu^0/Fe3O4 composites is proposed as electron transfer from the organic pollutants to PMS induces the activation of PMS to generate ^1O2,which induces the degradation of the organic pollutants.As a magnetic catalyst,the Cu^0/Fe3O4 composites were easily recovered by magnetic separation,and exhibited excellent stability over five successive degradation cycles.The present study provides a facile and green heterogeneous catalysis method for the oxidative removal of organic pollutants.

Preparation and mechanical properties of in situ Al_2O_3/Al composites by adding NH_4AlO(OH)HCO_3

Aluminium matrix composite reinforced by Al2O3 particles was produced by adding NH4AlO（OH）HCO3 into molten aluminum.The mechanical properties and wear behavior of the as-fabricated composites were studied.The results show that during stirring γ-Al2O3 particles were formed via decomposition reaction of NH4AlO（OH）HCO3,and the distribution of Al2O3 particles is more uniform in the matrix aluminum than directly added Al2O3 into molten aluminum.The density and the hardness values of the as-fabricated composites increase with increasing the particle volume fraction,while the tensile strength of the composites decreases with increasing the volume fraction of the Al2O3 particles.The wear rate of the composites decreases with increasing the volume fraction of the particle and loading.The in situ formed Al2O3/Al composite by adding NH4AlO（OH）HCO3 shows more superior mechanical and wear behaviors than that prepared by directly adding Al2O3 particles.

Alginate-Coated Fe3O4 Hollow Microspheres for Drug Delivery

Novel hollow Fe3O4 nanoparticles for drug delivery were synthesized via a one-step template- free approach. These nanoparticles were obtained by modifing the Fe3O4 nanoparticles with 3-aminopropyltrimethoxy silane, and then grafting alginate onto the surface of amine magnetic. The hollow structure of Fe3O4 spheres was characterized by TEM, XRD, and XPS. The M-H hysteresis loop indicated that the magnetic spheres exhibit snperparamagnetic characteristics at room temperature. Daunorubicin acting as a model drug was loaded into the carrier, and the maximum percent of envelop and load were 28.4% and 14.2% respectively. The drug controlled releasing behaviors of the carriers were compared in different pH media.

Preparation of Z-scheme WO_3(H_2O)_(0.333)/Ag_3PO_4 composites with enhanced photocatalytic activity and durability

Ag3PO4 is widely used in the field of photocatalysis because of its unique activity. However, photocorrosion limits its practical application. Therefore, it is very urgent to find a solution to improve the light corrosion resistance of Ag3PO4. Herein, the Z-scheme WO3(H2O)0.333/Ag3PO4 composites are successfully prepared through microwave hydrothermal and simple stirring. The WO3(H2O)0.333/Ag3PO4 composites are characterized by X-ray diffraction, scanning electron microscopy, X-ray photoelectron spectroscopy and UV-Vis spectroscopy. In the degradation of organic pollutants, WO3(H2O)0.333/Ag3PO4 composites exhibit excellent performance under visible light. This is mainly attributed to the synergy of WO3(H2O)0.333 and Ag3PO4. Especially, the photocatalytic activity of 15%WO3(H2O)0.333/Ag3PO4 is the highest, and the methylene blue can be completely degraded in 4 min. In addition, the stability of the composites is also greatly enhanced. After five cycles of testing, the photocatalytic activity of 15%WO3(H2O)0.333/Ag3PO4 is not obviously decreased. However, the degradation efficiency of Ag3PO4 was only 20.2%. This indicates that adding WO3(H2O)0.333 can significantly improve the photoetching resistance of Ag3PO4. Finally, Z-scheme photocatalytic mechanism is investigated.

Magnetic Fe_3O_4-Reduced Graphene Oxide Nanocomposites-Based Electrochemical Biosensing

An electrochemical biosensing platform was developed based on glucose oxidase(GOx)/Fe3O4-reduced graphene oxide(Fe3O4-RGO) nanosheets loaded on the magnetic glassy carbon electrode(MGCE).With the advantages of the magnetism, conductivity and biocompatibility of the Fe3O4-RGO nanosheets, the nanocomposites could be facilely adhered to the electrode surface by magnetically controllable assembling and beneficial to achieve the direct redox reactions and electrocatalytic behaviors of GOx immobilized into the nanocomposites. The biosensor exhibited good electrocatalytic activity, high sensitivity and stability. The current response is linear over glucose concentration ranging from 0.05 to 1.5 m M with a low detection limit of0.15 μM. Meanwhile, validation of the applicability of the biosensor was carried out by determining glucose in serum samples. The proposed protocol is simple, inexpensive and convenient, which shows great potential in biosensing application.

Absorption performance of DMSA modified Fe_3O_4@SiO_2 core/shell magnetic nanocomposite for Pb^(2+) removal

The purpose of this study is to explore the adsorption performance of meso-2,3-dimercaptosuccinic acid(DMSA)modified Fe3O4@SiO2 magnetic nanocomposite(Fe3O4@SiO2@DMSA)for Pb2+ions removal from aqueous solutions.The effects of solution pH,initial concentration of Pb2+ions,contact time,and temperature on the amount of Pb2+adsorbed were investigated.Adsorption isotherms,adsorption kinetics,and thermodynamic analysis were also studied.The results showed that the maximum adsorption capacity of the Fe3O4@SiO2@DMSA composite is 50.5 mg/g at 298 K,which is higher than that of Fe3O4 and Fe3O4@SiO2 magnetic nanoparticles.The adsorption process agreed well with Langmuir adsorption isotherm models and pseudo second-order kinetics.The thermodynamic analysis revealed that the adsorption was spontaneous,endothermic and energetically driven in nature.

An efficientfficient, controllable and facile two-step synthesis strategy： Fe3O4@RGO composites with various Fe3O4 nanoparticles and their supercapacitance properties

An efficient, controllable, and facile two-step synthetic strategy to prepare graphene-based nanocomposites is proposed. A series of Fe3O4-decorated reduced graphene oxide （Fe3O4@RGO） nanocomposites incorporating Fe3O4 nanocrystals of various sizes were prepared by an ethanothermal method using graphene oxide （GO） and monodisperse Fe3O4 nanocrystals with diameters ranging from 4 to 10 nm. The morphologies and microstructures of the as-prepared composites were characterized by X-ray diffraction, Raman spectroscopy, nitrogen adsorption measurements, and transmission electron microscopy. The results show that GO can be reduced to graphene during the ethanothermal process, and that the Fe3O4 nanocrystals are well dispersed on the graphene sheets generated in the process. The analysis of the electrochemical properties of the Fe3O4@RGO materials shows that nanocomposites prepared with Fe3O4 nanocrystals of different sizes exhibit different electrochemical performances. Among all samples, FegO4@RGO prepared with Fe3O4 nanocrystals of 6 nm diameter possessed the highest specific capacitance of 481 F/g at 1 A/g, highlighting the excellent capability of this material. This work illustrates a promising route to develop graphene-based nanocomposite materials with a wide range of potential applications.

Removing Cd^(2+) by Composite Adsorbent Nano-Fe_3O_4/Bacterial Cellulose

A new composite adsorbent, nano-Fe3O4/bacterial cellulose（BC）, was prepared through blending method. The process of adsorbing Cd2＋ including its isotherm and kinetics measured was studied. The results show that the adsorption efficiency is improved because of huge surface area and surface coordination of nano-Fe3O4 particles. Its adsorption capacity is 27.97 mg/g and the maximum of Cd2＋ removal is 74%. The adsorption kinetics can be described by pseudo-second rate model and the adsorption equilibrium by Langmuir type. The superparamagnetism of nano-Fe3O4 particles can help to solve the difficult separation of single BC adsorbent and lead to the quick separation of composite adsorbent from the liquid if a magnetic field was applied. Cd2＋ can be desorbed effectively by EDTA and HCl from the composite adsorbent, which can make it be reused.

Properties of Hot-Pressed Al_2O_3-Fe Composites

Alumina-(0 similar to 20 vol. pct) iron composites were fabricated by hot-pressing of well-mixed-alumina and iron powders at 1400 degreesC and 30 MPa for 30 min. Hot-pressed bodies with nearly theoretical density were obtained for addition up to 10 vol. pct Fe, but relative density decreased gradually with further increase in Fe addition. The materials exhibit a homogeneous dispersion of Fe. Fracture strength of the composites exhibits a maximum value of 604 MPa at 15 vol. pct Fe, which is 1.5 times that of alumina alone. Fracture toughness increases with the increase in Fe content, reaching 7.5 MPa.m(1/2) at 20 vol. pct Fe. The theoretical values of fracture toughness was calculated and compared with the experimental one. Toughening mechanisms of the composites are also discussed.

Enhanced Fenton,photo-Fenton and peroxidase-like activity and stability over Fe_3O_4/g-C_3N_4 nanocomposites

We prepared the Fe3O4/g‐C3N4nanoparticles(NPs)through a simple electrostatic self‐assembly method with a3:97weight ratio to investigate their Fenton,photo‐Fenton and oxidative functionalities besides photocatalytic functionality.We observed an improvement of the Fenton and photo‐Fenton activities of the Fe3O4/g‐C3N4nanocomposites.This improvement was attributed to efficient charge transfer between Fe3O4and g‐C3N4at the heterojunctions,inhibition of electron‐hole recombination,a high surface area,and stabilization of Fe3O4against leaching by the hydrophobic g‐C3N4.The obtained NPs showed a higher degradation potential for rhodamine B(RhB)dye than those of Fe3O4and g‐C3N4.As compared to photocatalysis,the efficiency of RhB degradation in the Fenton and photo‐Fenton reactions was increased by20%and90%,respectively.Additionally,the horseradish peroxidase(HRP)activity of the prepared nanomaterials was studied with3,3,5,5‐tetramethylbenzidinedihydrochloride(TMB)as a substrate.Dopamine oxidation was also examined.Results indicate that Fe3O4/g‐C3N4nanocomposites offers more efficient degradation of RhB dye in a photo‐Fenton system compared with regular photocatalytic degradation,which requires a long time.Our study also confirmed that Fe3O4/g‐C3N4nanocomposites can be used as a potential material for mimicking HRP owing to its high affinity for TMB.These findings suggest good potential for applications in biosensing and as a catalyst in oxidation reactions.

Effect of Al2O3np on the Properties and Microstructure of B4Cp/Al Composites

Aluminum-matrix boron carbide (B4Cp/Al) is a kind of neutron absorbing material widely used in nuclear spent fuel storage. In order to improve the tensile property of B4Cp/Al composites, a new type of nano-Al2O3 particle (Al2O3np) reinforced B4Cp/Al + Al2O3np composites were prepared by powder metallurgy method. The Monte Carlo particle transport program (MCNP) was used to determine the influence of Al2O3np on the thermal neutron absorptivity of composites. The universal material testing machine and scanning electron microscope (SEM) were used to study the mechanical properties, microstructure and fracture morphology of B4Cp/Al composites. The results indicated that the neutron absorption properties of B4Cp/Al composites were not affected by the addition of nano-Al2O3 particles in the range of 1 wt%-15 wt%. The addition of Al2O3np can obviously reduce the grain size of B4Cp/Al matrix metals thus improve the tensile strength of the composites. The addition threshold of Al2O3np is about 2.5 wt%. Both B4Cp and Al2O3np change the fracture characteristics of the composites from toughness to brittleness, and the latter is more important.

Fabrication of Fine-Grained Si_3N_4-Si_2N_2O Composites by Sintering Amorphous Nano-sized Silicon Nitride Powders

Si3N4-Si2N2O composites were fabricated with amorphous nano-sized silicon nitride powders by the liquid phase sintering （ LPS ）. The Si2 N2O phase was generated by an in-situ reaction 2 Si3 N4 （ s ） ＋ 1.5 02 （ g ） = 3 Si2 N2O （ s ） ＋ N2 （ g ） . The content of Si2 N2 O phase up to 60% in the volume was obtained at a sintering temperature of 1 650℃ and reduced when the sintering temperature increased or decreased, indicating the reaction is reversible. The mass loss, relative density and average grain size increased with increasing the sintering temperature. The average grain size was less than 500 nm when the sintering temperature was below 1 700 ℃. The sintering procedure contains a complex crystallization and a phase transition ： amorphous silicon nitride→equiaxial α- Si3 N4→ equiaxial β- Si3 N4→ rod- like Si2 N2O→ needle- like β- Si3N4 . Small round-shaped β→ Si3 N4 particles were entrapped in the Si2 N2O grains and a high density of staking faults was situated in the middle of Si2 N2O grains at a sintering temperature of 1 650 ℃. The toughness inereased from 3.5 MPa·m^1/2 at 1 600 ℃ to 7.2 MPa· m^1/2 at 1 800 ℃ . The hardness was as high as 21.5 GPa （Vickers） at 1 600 ℃ .

Preparation and Characterization of Superparamagnetic Fe_3O_4/CNTs Nanocomposites Dual-drug Carrier

Fe3O4/carbon nanotubes（Fe3O4/CNTs） nanocomposites were prepared by polylol hightemperature decomposition of the precursor ferric chloride and CNTs in liquid triethylene glycol.After surface modification with hexanediamine,folate was covalently linked to the amine group of magnetic Fe3O4/CNTs nanocomposites.The products were characterized by Fourier-transform infrared spectroscopy,transmission electron microscopy,and vibrating sample magnetometry.Then Fe3O4/CNTs were used as a dual-drug carrier to co-delivery of the hydrophilic drug epirubicin hydrochloride and hydrophobic drug paclitaxel.The results indicated that the Fe3O4/CNTs had a favorable release property for epirubicin and paclitaxel,and thus had potential application in tumor-targeted combination chemotherapy.

Magnetically recoverable Fe3O4@polydopamine nanocomposite as an excellent co-catalyst for Fe^3+ reduction in advanced oxidation processes

Advanced oxidation processes are widely applied to removal of persistent toxic substances from wastewater by hydroxyl radicals(·OH),which is generated from hydrogen peroxide(H2O2)decomposition.However,their practical applications have been hampered by many strict conditions,such as iron sludge,rigid pH condition,large doses of hydrogen peroxide and Fe^2+,etc.Herein,a magnetically recyclable Fe3O4@polydopamine(Fe3O4@PDA)coreshell nanocomposite was fabricated.As an excellent reducing agent,it can convert Fe^3+to Fe^2+.Combined with the coordination of polydopamine and ferric ions,the production of iron sludge is inhibited.The minimum concentration of hydrogen peroxide(0.2 mmol/L and Fe^2+(0.18 mmol/L))is 150-fold and 100-fold lower than that of previous reports,respectively.It also exhibits excellent degradation performance over a wide pH range from 3.0 to 9.0.Even after the tenth recycling,it still achieves over 99%degradation efficiency with the total organic carbon degradation rate of 80%,which is environmentally benign and has a large economic advantage.This discovery paves a way for extensive practical application of advanced oxidation processes,especially in environmental remediation.

Synthesis of Fe_3O_4-coated silica aerogel nanocomposites

Fe3O4:SiO2 nanocomposite powders were synthesized by a two-step process,which included the precipitation of FeCl2 and FeCl3 and the gelation of silicic acid solution derived from water glass.At first,Fe3O4 nanoparticles having a crystallite size of 20 nm were obtained by controlling the ratio of Fe(II) and Fe(III) precursors.In the second step,Fe3O4 particles were embedded in SiO2 matrix by the hydrolysis and subsequent condensation of the silicic acid solution containing Fe3O4 particles.It was found that the Fe3O4 nanoparticles homogenously disperse in the SiO2 matrix.The Fe3O4:SiO2 nanocomposite exhibited an enhanced thermal stability against oxidation compared with pure Fe3O4.FT-IR analysis indicates the presence of the Si-O-Fe bond in the Fe3O4:SiO2 (1:10,mole fraction) nanocomposite.

Preparation of MnO2-impregnated carbon-coated Fe3O4 nanocomposites and their application for bovine serum albumin adsorption

MnO2-impregnated carbon-coated Fe3 O4(Fe3O4/C/MnO2)nanocomposites with a good core-shell structure were prepared by direct oxidation of carbon-coated Fe3 O4(Fe3O4/C)microspheres with KMnO4 in alkaline solution and applied to adsorb bovine serum albumin(BSA).X-ray diffraction(XRD),transmission electron microscope(TEM),Fourier transform infrared spectrometer(FTIR),vibrating sample magnetometer(VSM)and thermogravimetric analyzer(TGA)tests show that Fe3O4/C microspheres were newly functionalized via the oxidation by KMnO4.Fe3O4/C/MnO2 nanocomposites exhibit a higher adsorption capacity for BSA than Fe3O4/C microspheres and the maximum adsorption of BSA on them occurs at pH 4.7,which is the isoelectric point of BSA.Langmuir isotherm model describes the adsorption of BSA better than Freundlich model and Temkin model,and the kinetics data fit well with the pseudo-second-order model.

A simple method for purification of genomic DNA from whole blood using Fe_3O_4/Au composite particles as a carrier

Objective： To establish a method of genomic DNA extraction from whole blood using Fe3O4/Au composite particles as a carrier. Methods： Two crucial conditions （sodium chloride concentration and amount of the magnetic particles） were optimized and 8 different human whole blood samples were used to purify genomic DNA under the optimal condition. Then agarose gel electrophoresis and polymerase cbain reaction （PCR） were performed. Results： The optimal binding condition was 1.5 mol/L NaC1/10% PEG, and the optimal amount of Fe3O4/Au composite particles was 600μg. The yields of the genomic DNA from 100μl of different whole blood samples were 2-5 μg, and the ratio of A260/A280 was in the range of 1.70-1.90. The size of genomic DNA was about 23 kb and the PCR was valid. Conclusion： The purification system using Fe3O4/Au composite microparticles has advantages in high yield, high purity, ease of operating, time saving and avoiding centrifugation. The purified sample was found to function satisfactorily in PCR amplification.