Aluminum(Al) 2024 matrix composites reinforced with alumina short fibers(Al_2O_(3sf)) and silicon carbide particles(SiC_p) as wear-resistant materials were prepared by pressure infiltration in this study. Further, the...Aluminum(Al) 2024 matrix composites reinforced with alumina short fibers(Al_2O_(3sf)) and silicon carbide particles(SiC_p) as wear-resistant materials were prepared by pressure infiltration in this study. Further, the effect of Al_2O_(3sf) on the friction and wear properties of the as-synthesized composites was systematically investigated, and the relationship between volume fraction and wear mechanism was discussed. The results showed that the addition of Al_2O_(3sf), characterized by the ratio of Al_2O_(3sf) to SiC_p, significantly affected the properties of the composites and resulted in changes in wear mechanisms. When the volume ratio of Al_2O_(3sf) to SiC_p was increased from 0 to 1, the rate of wear mass loss(K_m) and coefficients of friction(COFs) of the composites decreased, and the wear mechanisms were abrasive wear and furrow wear. When the volume ratio was increased from 1 to 3, the COF decreased continuously; however, the K_m increased rapidly and the wear mechanism became adhesive wear.展开更多
The morphology of the microstructure of Al-alloy composite with variousfiber contents was examined under optical microscope.The fracture of tension specimenwas studied under scanning electron microscope(SEM).The mecha...The morphology of the microstructure of Al-alloy composite with variousfiber contents was examined under optical microscope.The fracture of tension specimenwas studied under scanning electron microscope(SEM).The mechanical properties,wearresistance and coefficient of thermal linear expansion of the composite were measured.Theexperiment shows that the composite studied is suitable for engine pistons due to its goodwear resistance,higher elevated temperature mechanical properties and lower coefficient ofthermal linear expansion.展开更多
Fused deposition modelling(FDM)printed short carbon fibre reinforced nylon(SCFRN)composites were fabricated.The friction and wear behaviour of printed materials were systematically investigated under both dry sliding ...Fused deposition modelling(FDM)printed short carbon fibre reinforced nylon(SCFRN)composites were fabricated.The friction and wear behaviour of printed materials were systematically investigated under both dry sliding and water lubricated conditions.The results showed that with short fibre enhancements,the printed SCFRN achieved a lower friction coefficient and higher wear resistance than nylon under all tested conditions.Further,under water lubricated conditions,the printed SCFRN exhibited a low,stable friction coefficient due to the cooling and lubricating effects of water.However,the specific wear rate of the printed specimens could be higher than that obtained under dry sliding conditions,especially when the load was relatively low.The square textured surface was designed and created in the printing process to improve materials’tribological performance.It was found that with the textured surface,the wear resistance of the printed SCFRN was improved under dry sliding conditions,which could be explained by the debris collection or cleaning effect of surface texture.However,such a cleaning effect was less noticeable under lubricated conditions,as the liquid could clean the surface effectively.On the other hand,surface textures could increase the surface area exposed to water,causing surface softening due to the higher water absorption rate.As a result,the samples having surface textures showed higher wear rates under lubricated conditions.The work has provided new insights into designing wear resistant polymer materials using three-dimensional(3D)printing technologies,subjected to different sliding conditions.展开更多
In addition to the advantage of the lightweight of magnesium alloys, magnesium composites have moderate strength and elastic modulus. The proposed application of magnesium composites as diesel truck pistons makes it n...In addition to the advantage of the lightweight of magnesium alloys, magnesium composites have moderate strength and elastic modulus. The proposed application of magnesium composites as diesel truck pistons makes it necessary to assess their wear performance. Little research data have been discussed on wear behavior of Mg alloy AE42 matrix and its composites. Thus, this paper reports wear behavior of magnesium alloy AE42(Mg–Al–Mn—RE; rare earth) and its composite AE42-C, which contains 23 vol% of randomly oriented carbon short fibers. Materials characterization, including density measurements, hardness testing, microstructures investigation, and compression testing at temperatures of 25, 150,and 300 °C, were conducted. Wear tests were performed under various loads and sliding distances. Wear mechanisms were also proposed based on the examination of worn surfaces using optical microscopy and scanning electron microscopy equipped with EDX(energy-dispersive X-ray spectrometry) analysis system. The hardness of AE42-23 vol% C composite is twice the hardness of the Mg matrix alloy AE42. Significant improvements to yield stress and compressive strength at temperatures of 25, 150, and 300 °C of the composite versus the AE42 alloy are achieved. Wear resistance of the composite is improved considerably versus that of the Mg alloy AE42 at the various sliding distances. Smearing of graphite on the worn surface produces a lubricating film that delays change from mild to severe wear of the composite, especially at high loads. EDX analysis of the worn surface shows oxidation of the matrix alloy at higher wear loads, and this mechanism decreases in the presence of carbon fibers under the same loads. Abrasive wear, oxidation, and plastic deformation are the dominant wear mechanisms for the alloy matrix AE42, whereas mainly abrasive wear is the wear mechanism of AE42-23 vol% C composite under the proposed testing conditions.展开更多
基金financially supported by the National Natural Science Foundation of China (No. 51374028)
文摘Aluminum(Al) 2024 matrix composites reinforced with alumina short fibers(Al_2O_(3sf)) and silicon carbide particles(SiC_p) as wear-resistant materials were prepared by pressure infiltration in this study. Further, the effect of Al_2O_(3sf) on the friction and wear properties of the as-synthesized composites was systematically investigated, and the relationship between volume fraction and wear mechanism was discussed. The results showed that the addition of Al_2O_(3sf), characterized by the ratio of Al_2O_(3sf) to SiC_p, significantly affected the properties of the composites and resulted in changes in wear mechanisms. When the volume ratio of Al_2O_(3sf) to SiC_p was increased from 0 to 1, the rate of wear mass loss(K_m) and coefficients of friction(COFs) of the composites decreased, and the wear mechanisms were abrasive wear and furrow wear. When the volume ratio was increased from 1 to 3, the COF decreased continuously; however, the K_m increased rapidly and the wear mechanism became adhesive wear.
文摘The morphology of the microstructure of Al-alloy composite with variousfiber contents was examined under optical microscope.The fracture of tension specimenwas studied under scanning electron microscope(SEM).The mechanical properties,wearresistance and coefficient of thermal linear expansion of the composite were measured.Theexperiment shows that the composite studied is suitable for engine pistons due to its goodwear resistance,higher elevated temperature mechanical properties and lower coefficient ofthermal linear expansion.
文摘Fused deposition modelling(FDM)printed short carbon fibre reinforced nylon(SCFRN)composites were fabricated.The friction and wear behaviour of printed materials were systematically investigated under both dry sliding and water lubricated conditions.The results showed that with short fibre enhancements,the printed SCFRN achieved a lower friction coefficient and higher wear resistance than nylon under all tested conditions.Further,under water lubricated conditions,the printed SCFRN exhibited a low,stable friction coefficient due to the cooling and lubricating effects of water.However,the specific wear rate of the printed specimens could be higher than that obtained under dry sliding conditions,especially when the load was relatively low.The square textured surface was designed and created in the printing process to improve materials’tribological performance.It was found that with the textured surface,the wear resistance of the printed SCFRN was improved under dry sliding conditions,which could be explained by the debris collection or cleaning effect of surface texture.However,such a cleaning effect was less noticeable under lubricated conditions,as the liquid could clean the surface effectively.On the other hand,surface textures could increase the surface area exposed to water,causing surface softening due to the higher water absorption rate.As a result,the samples having surface textures showed higher wear rates under lubricated conditions.The work has provided new insights into designing wear resistant polymer materials using three-dimensional(3D)printing technologies,subjected to different sliding conditions.
文摘In addition to the advantage of the lightweight of magnesium alloys, magnesium composites have moderate strength and elastic modulus. The proposed application of magnesium composites as diesel truck pistons makes it necessary to assess their wear performance. Little research data have been discussed on wear behavior of Mg alloy AE42 matrix and its composites. Thus, this paper reports wear behavior of magnesium alloy AE42(Mg–Al–Mn—RE; rare earth) and its composite AE42-C, which contains 23 vol% of randomly oriented carbon short fibers. Materials characterization, including density measurements, hardness testing, microstructures investigation, and compression testing at temperatures of 25, 150,and 300 °C, were conducted. Wear tests were performed under various loads and sliding distances. Wear mechanisms were also proposed based on the examination of worn surfaces using optical microscopy and scanning electron microscopy equipped with EDX(energy-dispersive X-ray spectrometry) analysis system. The hardness of AE42-23 vol% C composite is twice the hardness of the Mg matrix alloy AE42. Significant improvements to yield stress and compressive strength at temperatures of 25, 150, and 300 °C of the composite versus the AE42 alloy are achieved. Wear resistance of the composite is improved considerably versus that of the Mg alloy AE42 at the various sliding distances. Smearing of graphite on the worn surface produces a lubricating film that delays change from mild to severe wear of the composite, especially at high loads. EDX analysis of the worn surface shows oxidation of the matrix alloy at higher wear loads, and this mechanism decreases in the presence of carbon fibers under the same loads. Abrasive wear, oxidation, and plastic deformation are the dominant wear mechanisms for the alloy matrix AE42, whereas mainly abrasive wear is the wear mechanism of AE42-23 vol% C composite under the proposed testing conditions.
