Fracture Behavior of Alumina-based Prismatic Ceramic Composites

The fracture toughness and fracture work of A12O3/SiC prismatic ceramic composites was evaluated in this paper, which showed the fracture energy was improved greatly. Based on the observation 'for crack propagation and fracture morphology, the fracture behavior of the prismatic composites was analyzed. In the bending test, the composites displayed a non-catastrophic behavior and a graceful failure with reasonable load-carrying capability.

Hardness, Wear Resistance and Fracture Toughness of Cast Hiduminium/Corundum Particulate Composites

This paper reports some results obtained in an investigation to see how increasing the corundum dispersoid content from 0% to 7% in a matrix of as-cast and wrought hiduminium alloy affects the hardness. wear resistance and fracture toughness of the composite. The results show that as the corundum content is increased, the hardness and the wear resistance increase remarkably,whereas the fracture toughness drops significantly. It was found that Just a minute amount of corundum is sufficient to cause a fairly large change in these mechanical properties. The hardness of the material is also affected signifIcantly by the aging time. Moreover, if other factors are kept constant, hot extrusion improves both its hardness and its wear resistance. whereas the fracture toughness is decreased

Control of Fracture Behavior of Carbon Fiber/Pitch-based CarbonMatrix Composites with Microspace Modification Concept

Theoretical consideration was conducted on a relation between pore diameter and interfacialarea between pores and fibers when pores uniforinly distribute in C/C composites. It was shownthat bonding at the fiber/matrix interface apparently decreased with decreasing a pore diameter,and consequently a new idea of microspace modification concept was proposed for controllingfracture behavior of C/C composites. Four types of C/C composites with various pore structureswere fabricated by hot-pressing, and their fracture behavior was investigated by three pointbending tests. The fracture behavior of the C/C composites was changed from brittle one topseudo ductile one with decreasing the pore diameter. This result supported the validity of themicrospace modification concept proposed in this paper.

Effect of Oxidation on Fracture Toughness of a Carbon/Carbon Composite

The fracture toughness of a carbon/carbon composites oxidized at different temperature for 1 h was measured. The fracture surfaces were examined by scanning electron microscopy （SEM）. The results indicate that oxidation temperature has significant effects on the fracture toughness. Fracture toughness decreases with the increase of the weight loss. The SEM images reveal that the decrease of fracture toughness was mainly attributed to the oxidation of the interface in the composite.

Damage and Fracture Strength Behavior of Jointed Rockmass

The strength of rockmass from two aspects is analyzed.Firstly,the strength of the rockmass is mainly controlled by the critical stress value of rock,and the contribution of joints is to increase the effective stresses of rock and to decrease the damage strength of rockmass according to the macro damage mechanics of rockmass.Secondly,the strength of rockmass is mainly controlled by the fracture strength of joints.Based on the comprehensive analysis and comparison for the damage strength of rockmass and the fracture strength of joints,a composite damage theory of rockmass may be established.

Quasimolecular Dynamic Simulation for Bending Fracture of Laminar Composite Materials

Recently, quasimolecular dynamics has been successfully used to simulate the deformation characteristics of actual size solid materials. In quasimolecular dynamics, which is an attempt to bridge the gap between atomistic and continuum simulations, molecules are aggregated into large units, called quasimolecules, to evaluate large scale material behavior. In this paper, a 2-dimensional numerical simulation using quasimolecular dynamics was performed to investigate laminar composite material fractures and crack propagation behavior in the uniform bending of laminar composite materials. It was verified that under bending deformation laminar composite materials deform quite differently from homogeneous materials

SEM in-situ Fracture Observation and the Reinforcing Effect of Composite SiC_p/ZA22

The strengthening effect of a Zn alloy reinforced by SiC particulate was examined. Based on the results of SEM in-situ fracture observation and stress field analysis by finite element method, it is believed that the reinforcing effect of this composite is due to the combination of strain and stress hardening in the matrix.

Microstructure and mechanical properties of heat affected zone in multi-pass GMA welded Al-Zn-Mg-Cu alloy

Microstructure and mechanical properties of the heat affected zone(HAZ)in multi-pass gas metal arc(GMA)welded Al Zn Mg Cu alloy plates were investigated,based upon which the mechanical anisotropy and fracture mechanism were analyzed.The microstructure and composition were analyzed by scanning electron microscope(SEM)and energy dispersive spectroscope(EDS).X-ray diffractometer(XRD),transmission electron microscope(TEM)and selective area electron diffraction(SAED)were used to analyze the phase composition.The distribution of microhardness was identified as gradual transition and tensile strength had a tendency to decrease first and then increase.The distribution of nano-sizedη(MgZn2)particles in theα(Al)matrix and Al2MgCu phase determined the tensile performances along the thickness direction and led to the formation of ductile/brittle composite fracture in the HAZ.The continuous distribution of Al2MgCu phase in the strip intergranular precipitates gave birth to premature cracks and the brittle fracture region.The precipitated particles coarsening also led to the deterioration of mechanical properties.

Mechanical Properties and Fracture Behavior of Mg-Al/AlN Composites with Different Particle Contents

In this study, magnesium matrix composites reinforced with different loading of AlN particles were fabricated by the powder metallurgy technique. The microstructure, bending strength and fracture behavior of the resulting Mg-Al/Al N composites were investigated. It showed that the 5 wt% AlN reinforcements led to the highest densification and bending strength. The total strengthening effect of AlN particles was predicted by considering the contributions of CTE mismatch between the matrix and the particles,load bearing and Hall-Petch mechanism. The results revealed that the increase of dislocation density,the change of Mg17Al12 phase morphology, and the effective load transfer were the major strengthening contributors to the composites. The fracture of the composites altered from plastic to brittle mode with increasing reinforcement content. The regions of clustered particles in the composites were easy to be damaged under external load, and the fracture occurred mainly along grain boundaries.

Research on Composite Fracturing Technology in Qiaokou Oilfield, Dongpu Depression

Limited by serious heterogeneity both horizontally and vertically, water driving of low-permeability layers in Qiaokou oilfield appears to be very difficult. As the classⅠ layer reaches the stage of high water-content too early, the level of exploitation became worse with low-recovery. Regarding the serious heterogeneity and low recovery in layers class Ⅱand Ⅲ, composite fracturing technology suitable for this kind of reservoir was applied. Its basement was a lab study of indoor water driving efficiency and fracturing experiment. Perfect result has achieved by using the technology.

Microstructure and tensile behavior of 2D-C_f/AZ91D composites fabricated by liquid–solid extrusion and vacuum pressure infiltration

2D carbon fiber reinforced AZ91 D matrix composites（2D-C_f/AZ91 D composites） were fabricated by liquid–solid extrusion and vacuum pressure infiltration technique（LSEVI）. In order to modify the interface between fibers and matrix and protect the fiber, pyrolytic carbon（Py C） coating was deposited on the surface of T700 carbon fiber by chemical vapor deposition（CVD）. Microstructure observation of the composites revealed that the composites were well fabricated by LSEVI. The segregation of aluminum at fiber surface led to the formation of Mg_（17）Al_（12） precipitates at the interface. The aluminum improved the infiltration of the alloy and Py C coating protected the fibers effectively. The ultimate tensile strength of 2D-C_f/AZ91 D composites was about 400 MPa. The fracture process of 2D-C_f/AZ91 D composites was transverse fiber interface cracking–matrix transferring load–longitudinal fibers bearing load–longitudinal fibers breaking.