An intelligent control method based on artificial neural network for numerical flight simulation of the basic finner projectile with pitching maneuver

In this paper,an intelligent control method applying on numerical virtual flight is proposed.The proposed algorithm is verified and evaluated by combining with the case of the basic finner projectile model and shows a good application prospect.Firstly,a numerical virtual flight simulation model based on overlapping dynamic mesh technology is constructed.In order to verify the accuracy of the dynamic grid technology and the calculation of unsteady flow,a numerical simulation of the basic finner projectile without control is carried out.The simulation results are in good agreement with the experiment data which shows that the algorithm used in this paper can also be used in the design and evaluation of the intelligent controller in the numerical virtual flight simulation.Secondly,combined with the real-time control requirements of aerodynamic,attitude and displacement parameters of the projectile during the flight process,the numerical simulations of the basic finner projectile’s pitch channel are carried out under the traditional PID(Proportional-Integral-Derivative)control strategy and the intelligent PID control strategy respectively.The intelligent PID controller based on BP(Back Propagation)neural network can realize online learning and self-optimization of control parameters according to the acquired real-time flight parameters.Compared with the traditional PID controller,the concerned control variable overshoot,rise time,transition time and steady state error and other performance indicators have been greatly improved,and the higher the learning efficiency or the inertia coefficient,the faster the system,the larger the overshoot,and the smaller the stability error.The intelligent control method applying on numerical virtual flight is capable of solving the complicated unsteady motion and flow with the intelligent PID control strategy and has a strong promotion to engineering application.

Analysis of debris flow control effect and hazard assessment in Xinqiao Gully,Wenchuan M_(s)8.0 earthquake area based on numerical simulation

Xinqiao Gully is located in the area of the 2008 Wenchuan M_(s)8.0 earthquake in Sichuan province,China.Based on the investigation of the 2023"6-26"Xinqiao Gully debris flow event,this study assessed the effectiveness of the debris flow control project and evaluated the debris flow hazards.Through field investigation and numerical simulation methods,the indicators of flow intensity reduction rate and storage capacity fullness were proposed to quantify the effectiveness of the engineering measures in the debris flow event.The simulation results show that the debris flow control project reduced the flow intensity by41.05%to 64.61%.The storage capacity of the dam decreases gradually from upstream to the mouth of the gully,thus effectively intercepting and controlling the debris flow.By evaluating the debris flow of different recurrence intervals,further measures are recommended for managing debris flow events.

Performance analysis model for real-time Ethernet-based computer numerical control system

In order to optimize the embedded system implementation for Ethernet-based computer numerical control (CNC) system,it is very necessary to establish the performance analysis model and further adopt the codesign method from the control,communication and computing perspectives.On the basis of analyzing real-time Ethernet,system architecture,time characteristic parameters of control-loop etc,a performance analysis model for real-time Ethernet-based CNC system was proposed,which is able to include the timing effects caused by the implementation platform in the simulation.The key for establishing the model is accomplished by designing the error analysis module and the controller nodes.Under the restraint of CPU resource and communication bandwidth,the experiment with a case study was conducted,and the results show that if the deadline miss ratio of data packets is 0.2%,then the percentage error is 1.105%.The proposed model can be used at several stages of CNC system development.

Real-Time Data and Visualization Monitoring of Computer Numerical Control Machine Tools Based on Hyper Text Markup Language 5

In order to ensure the safety,quality and efficiency of computer numerical control(CNC)machine tool processing,a real-time monitoring and visible solution for CNC machine tools based on hyper text markup language(HTML)5 is proposed.The characteristics of the real-time monitoring technology of CNC machine tools under the traditional Client/Server(C/S)structure are compared and analyzed,and the technical drawbacks are proposed.Web real-time communication technology and browser drawing technology are deeply studied.A real-time monitoring and visible system for CNC machine tool data is developed based on Metro platform,combining WebSocket real-time communication technology and Canvas drawing technology.The system architecture is given,and the functions and implementation methods of the system are described in detail.The practical application results show that the WebSocket real-time communication technology can effectively reduce the bandwidth and network delay and save server resources.The numerical control machine data monitoring system can intuitively reflect the machine data,and the visible effect is good.It realizes timely monitoring of equipment alarms and prompts maintenance and management personnel.

Java Language for Numerical Control Simulation System Research

Java language is widely used in a variety of development platforms to develop all kinds of application software for its simple and efficient.The programming language owning platform independent is adopted to solve the image flicker,sound loading and other issues by the threading technology,multimedia technology,graphics and point by point comparison techniques.Dynamic real⁃time process simulation is implemented and a two⁃dimensional network of CNC machining simulation system is developed while Java applet application is as a carrier.The simulation results show that the system has a friendly interface and fast calculation speed,and platform portability has a certain practicality and application value.

Discussion on Reverse Design of Components with Complex Curved Surface and Computer Numerical Control Machining

With the continuous development and advancement of science and technology,the work of tool path planning has received extensive attention.Among them,curved surface generation and data processing are the focus of management and design,which necessitate the full application of reverse design of complex curved surface components to complete numerical control processing,effective optimization and upgrading,integration the tasks of point cloud data collection,and point cloud data processing to ensure that the corresponding computer numerical control machining model can exert its actual value.This paper briefly analyzes the basic principles of curved surface reconstruction as well as discusses the reverse design of complex curved components and the experimental processes and results that involved computer numerical control machining,which serves the purpose as reference only.

An Investigation into the Life Cycle Cost of a Typical Computer Numerical Control Machine

This paper relates to a typical computer numerical control (CNC) machine, model FDXNC 128, and analyzes the payoff period quantitatively and forecasts the future maintenance cost and the evaluation of the economic benefit by using Life Cycle Cost (LCC) method and grey theory. The discussion shows conclusions that are beneficial to the production, management, and decision making of the enterprise.

利用CNC多维约束的S型速度规划

经典控制模型中存在时间过耦合,而速度规划与实时轨迹控制都与时间关联,导致实时计算量、规划与控制协调性等不足的问题,提出利用CNC多维约束的S型速度规划方法.首先建立双重反馈的控制模型,内反馈继承经典控制模型将时间反馈到控制器,外反馈将非时间反馈到规划器;然后将影响速度规划的因素分为时间相关与时间无关,与时间相关因素在控制器中实时控制,与时间无关因素在规划器中进行非时间速度规划;在规划器中建立基于轨迹路径长度、轨迹几何特性、运动参数以及程序行号等信息的多维约束模型;最后以路径长度代替时间作为运动参考量,结合多维约束模型,考虑轨迹的几何特性与路径长度映射关系,使轨迹特性与非时间建立具有空间性关联.通过MATLAB仿真对控制模型的抗干扰能力进行验证,并通过CODESYS软件编程和实验的结果表明,所提方法是可行和有效的.

Shaking table test and numerical analysis of offshore wind turbine tower systems controlled by TLCD

A wind turbine system equipped with a tuned liquid column damper （TLCD） is comprehensively studied via shaking table tests using a 1/13-scaled model. The effects of wind and wave actions are considered by inputting response- equivalent accelerations on the shaking table. The test results show that the control effect of the TLCD system is significant in reducing the responses under both wind-wave equivalent loads and ground motions, but obviously varies for different inputs, Further, a blade-hub-tower integrated numerical model for the wind turbine system is established. The model is capable of considering the rotational effect of blades by combining Kane＇s equation with the finite element method. The responses of the wind tower equipped with TLCD devices are numerically obtained and compared to the test results, showing that under both controlled and uncontrolled conditions with and without blades＇ rotation, the corresponding responses exhibit good agreement. This demonstrates that the proposed numerical model performs well in capturing the wind-wave coupled response of the offshore wind turbine systems under control. Both numerical and experimental results show that the TLCD system can significantly reduce the structural response and thus improve the safety and serviceability of the offshore wind turbine tower systems. Additional issues that require further study are discussed.

Numerical modelling of structural controls on fluid flow and mineralization

This paper presents the results of a set of numerical models focussing on structural controls on hydrothermal mineralization. We first give an overview of natural phenomena of structurally-controlled ore formation and the background theory and mechanisms for such controls. We then provide the results of a group of simple 2D numerical models validated through comparison with Cu-vein structure observed near the Shilu Copper deposit （Yangchun, Guangdong Province, China） and finally a case study of 3D numerical modelling applied to the Hodgkinson Province in North Queensland （Australia）. Two modelling approaches, discrete deformation modelling and continuum coupled deformation and fluid flow modelling, are involved. The 2D model-derived patterns are remarkably consistent with the Cu-vein structure from the Shilu Copper deposit, and show that both modelling approaches can realistically simulate the mechanical behaviours of shear and dilatant fractures. The continuum coupled deformation and fluid flow model indicates that pattern of the Cu- veins near the Shilu deposit is the result of shear strain localization, development of dilation and fluid focussing into the dilatant fracture segments. The 3D case-study models （with deformation and fluid flow coupling） on the Hodgkinson Province generated a number of potential gold mineralization

Underground ground control monitoring and interpretation,and numerical modeling, and shield capacity design

Mine or longwall panel layout is a 3D structure with highly non-uniform stress distribution. Recognition of such fact will facilitate underground problem identification/investigation and solving by numerical modeling through proper model construction. Due to its versatility, numerical modeling is the most popular method for ground control design and problem solving. However numerical modeling results require highly experienced professionals to interpret its validity/applicability to actual mining operations due to complicated mining and geological conditions. Underground ground control monitoring is routinely performed to predict roof behavior such as weighting and weighting interval without matching observation of face mining condition while the mining pressures are being monitored, resulting in unrealistic interpretation of the obtained data on mining pressure. The importance of ground control pressure monitoring and simultaneous observation of mining and geological conditions is illustrated by an example of shield leg pressure monitoring and interpretation in an U.S. longwall coal mine: it was found that the roof strata act like a plate, not an individual block of the size of a shield dimension, as commonly assumed by all researchers and shield capacity is not a fixed property for a longwall panel or a mine or a coal seam. A new mechanism on the interaction between shield's hydraulic leg pressure and roof strata for shield loading is proposed.

NUMERICAL SOLUTION OF VISCOUS FLOW PAST A SOLID SPHERE WITH THE CONTROL VOLUME FORMULATION

The control volume formulation with the QUICK finite difference scheme is used to solveincompressible liquid flow past a solid sphere in terms of stream function and vorticity.Several tech-nical points are addressed on improving the accuracy and efficiency of numerical simulation of similarproblems of fluid flow.In particular,the importance of suitable specification of the distortion func-tion to enforcing the far field boundarv conditions is emphasized.

NOVEL STRUCTURE FOR DISTRIBUTED NUMERICAL CONTROL

Because of an unexpected signal noise within the network or an unpredictedfault with personal computers (PCs), many problems emerge in the implementation of distributednumerical control (DNC) with PCs-based network. To solve the problems, an industrial solution ofinvolving the field-bus technology in DNC communicating area is provided. A kind of advancedField-bus, named controller area network (CAN), is originally developed to support cheap and rathersimple automotive applications. However, because of its good performance and low cost, it is alsobeing considered in automated-manufacturing and process control environments to interconnectintelligent devices, such as modem sensors and actuators. Recently it creates a new role for CANBusin DNC that brings new thinking to DNC. CAN is used as the network platform for connecting machinetools to share information with each other reliably. Additionally, thanks to also applying of'plug-in' technology and a special interface of hardware, this solution exhibits some highcompatibility with different pedigree numerical control (NC) systems, such as Fanuc, Siemens,Cincinnati and so on. In order to improve CANBus for DNC application, a communicating competitionmodel of the basic CAN protocol, called CC model, is then highlighted. This model is able to satisfythe requirements that different machine tools share the communicating bandwidth fairly when theyrun concurrently. Finally the novel view of the latest advancement in CANBus-based DNC incombination with the manufacturing paradigm is also presented.

A Numerical-analytic Method for Quickly Predicting Springback of Numerical Control Bending of Thin-walled Tube

Springback is one of important factors influencing the forming quality of numerical control （NC） bending of thin-walled tube. In this paper, a numerical-analytic method for springback angle prediction of the process was put forward. The method is based on springback angle model derived using analytic method and simulation results from three-dimensional （3D） rigid-plastic finite element method （FEM）. The method is validated through comparison with experimental results. The features of the method are as follows： （1） The method is high in efficiency because it combines advantages of rigid-plastic FEM and analytic method. （2） The method is satisfactory in accuracy, since the field variables used in the model is resulting from 3D rigid-plastic FEM solution, and the effects both of axial force and strain neutral axis shift have been included. （3） Research on multi-factor effects can be carried out using the method due to its advantage inheriting from rigid-plastic FEM. The method described here is also of general significance to other bending processes.

A Windows bitmap-based numerically controlled sculpture method and its application

Bitmap （BMP） is a widely used format in image processing. With the combination of the digital image processing and computer numerically controlled （NC） techniques, we developed a bitmap-based NC single-step and multi-dot method. An example was provided to illustrate the application and principle of this bitmap-based method in our newly innovated sandblasting glass NC sculpture system.

Mathematical model for the thermal process of controlled cooling of wires and its numerical simulation

The mathematical model for the thermal process of billets rolling has beenestablished, including transporting in air and temperature-holding cover, descaling withhigh-pressure water, and the process of rolling and cooling in water box. The calculated data by themodel have been compared with the measured data and the results show that the model is right andcreditable. Based on the model, the main thermal characters of rolling line have been simulated andthe influence of all the parameters on the temperature of rolling has been analyzed.

NUMERICAL SIMULATION OF MOLTEN POOL AND CONTROL STRATEGY OF KISS POINT IN A TWIN-ROLL STRIP CASTING PROCESS

Coupled turbulent flow, temperature fields of the twin-roll casting strip process were simulated by three-dimensional finite element method. Based on the heat balance calculation and using inverse methods between the simulations and real experiments, the relational models among casting speed, location, and coefficient of heat transfer between molten metal and rolls in different regions are given. In the simulation, the calculated surface temperatures are in good agreement with the measured values. An on-line model of kiss point is derived by simulations and the geometry of molten pool, corresponding control strategy is also proposed.

Research and Development of an Embedded Numerical Control System

This paper puts forward a new scheme of Embedded Numerical Control System based on ARM and DSP,which is at the base of research on traditional numerical control system and embedded technology.And the paper also describes the develop- ment of hardware and software platform.All the development and realization are based on the idea of module design.The embed- ded numerical control system,using ARM and DSP to construct the main control platform,realizes the real-time operation of sys- tem and improves the stability and reliability with the modular designing ideas of hardware and software and with the support of embedded real-time operating system(uc/os-Ⅱ).And the system could realize the multi-network supporting,which is also accord with the development of modularization,flexibility and latticing of numerical control system.

Research on Remote Monitoring and Fault Diagnosis Technology of Numerical Control Machine

Based on the internet technology,it has become possible to complete remote monitoring and fault diagnosis for the numerical control machine.In order to capture the micro-shock signal induced by the incipient fault on the rotating parts,the reso- nance demodulation technology is utilized in the system.As a subsystem of the remote monitoring system,the embedded data acquisi- tion instrument not only integrates the demodulation board but also complete the collection and preprocess of monitoring data from different machines.Furthermore,through connecting to the internet,the data can be transferred to the remote diagnosis center and data reading and writing function can be finished in the database.At the same time,the problem of the IP address floating in the dial-up of web server is solved by the dynamic DNS technology.Finally,the remote diagnosis software developed on the Lab VIEW platform can analyze the monitoring data from manufacturing field.The research results have indicated that the equipment status can be monitored by the system effectively.

Bayesian zero-failure reliability modeling and assessment method for multiple numerical control(NC) machine tools

A new problem that classical statistical methods are incapable of solving is reliability modeling and assessment when multiple numerical control machine tools(NCMTs) reveal zero failures after a reliability test. Thus, the zero-failure data form and corresponding Bayesian model are developed to solve the zero-failure problem of NCMTs, for which no previous suitable statistical model has been developed. An expert-judgment process that incorporates prior information is presented to solve the difficulty in obtaining reliable prior distributions of Weibull parameters. The equations for the posterior distribution of the parameter vector and the Markov chain Monte Carlo(MCMC) algorithm are derived to solve the difficulty of calculating high-dimensional integration and to obtain parameter estimators. The proposed method is applied to a real case; a corresponding programming code and trick are developed to implement an MCMC simulation in Win BUGS, and a mean time between failures(MTBF) of 1057.9 h is obtained. Given its ability to combine expert judgment, prior information, and data, the proposed reliability modeling and assessment method under the zero failure of NCMTs is validated.