Assessing mixing uniformity in microreactors via in-line spectroscopy

Mixing behavior is critical for enhancing the selectivity of fast chemical reactions in microreactors.A high Reynolds number(Re)improves the mixing rate and selectivity of the reactions,but some exceptions of increasing side product yield with the higher Re have been reported.This study investigated the mixing uniformity in microreactors with in-line UV-vis spectroscopy to clarify the relationship between reaction selectivity and chaotic mixing with the higher Re.A colorization experiment of thymolphthalein in an acidic solution was conducted with an excess acid amount to the base to indicate a non-uniformly mixed region.Non-uniformity significantly increased with Re.At the same time,the degree of mixing,which was measured by a usual decolorization experiment,showed that the mixing rate increased with Re.The in-line analysis of the Villermaux-Dushman reaction during the mixing clarified that side product yield significantly increased with Re at around 300 and then decreased at around 1100.These results suggest the compensation effect between the mixing uniformity and mixing rate on the selectivity of the mixing-sensitive reactions.Faster mixing,characterized by a larger Re,can disturb mixing uniformity and,in some cases,decrease reaction selectivity.

Customized modulation on plasma uniformity by non-uniform magnetic field in capacitively coupled plasma

A two-dimensional fluid model based on COMSOL Multiphysics is developed to investigate the modulation of static magnetic field on plasma homogeneity in a capacitively coupled plasma(CCP)chamber. To generate a static magnetic field, direct current is applied to a circular coil located at the top of the chamber. By adjusting the magnetic field's configuration, which is done by altering the coil current and position, both the plasma uniformity and density can be significantly modulated. In the absence of the magnetic field, the plasma density exhibits an inhomogeneous distribution characterized by higher values at the plasma edge and lower values at the center. The introduction of a magnetic field generated by coils results in a significant increase in electron density near the coils. Furthermore, an increase in the sets of coils improves the uniformity of the plasma. By flexibly adjusting the positions of the coils and the applied current,a substantial enhancement in overall uniformity can be achieved. These findings demonstrate the feasibility of using this method for achieving uniform plasma densities in industrial applications.

Effect of dielectric material on the uniformity of nanosecond pulsed dielectric barrier discharge

Dielectric barrier discharge(DBD)is considered as a promising technique to produce large volume uniform plasma at atmospheric pressure,and the dielectric barrier layer between the electrodes plays a key role in the DBD processes and enhancing discharge uniformity.In this work,the uniformity and discharge characteristics of the nanosecond(ns)pulsed DBD with dielectric barrier layers made of alumina,quartz glass,polycarbonate(PC),and polypropylene(PP)are investigated via discharge image observation,voltage-current waveform measurement and optical emission spectral diagnosis.Through analyzing discharge image by gray value standard deviation method,the discharge uniformity is quantitatively calculated.The effects of the space electric field intensity,the electron density(Ne),and the space reactive species on the uniformity are studied with quantifying the gap voltage Ug and the discharge current Ig,analyzing the recorded optical emission spectra,and simulating the temporal distribution of Ne with a one-dimensional fluid model.It is found that as the relative permittivity of the dielectric materials increases,the space electric field intensity is enhanced,which results in a higher Ne and electron temperature(Te).Therefore,an appropriate value of space electric field intensity can promote electron avalanches,resulting in uniform and stable plasma by the merging of electron avalanches.However,an excessive value of space electric field intensity leads to the aggregation of space charges and the distortion of the space electric field,which reduce the discharge uniformity.The surface roughness and the surface charge decay are measured to explain the influences of the surface properties and the second electron emission on the discharge uniformity.The results in this work give a comprehensive understanding of the effect of the dielectric materials on the DBD uniformity,and contribute to the selection of dielectric materials for DBD reactor and the realization of atmospheric pressure uniform,stable,and reactive plasma sources.

Uniformity Control of Scanned Beam in 300 MeV Proton and Heavy Ion Accelerator Complex at SESRI

In recent years,heavy ion accelerator technology has been rapidly developing worldwide and widely applied in the fields of space radiation simulation and particle therapy.Usually,a very high uniformity in the irradiation area is required for the extracted ion beams,which is crucial because it directly affects the experimental precision and therapeutic effect.Specifically,ultra-large-area and high-uniformity scanning are crucial requirements for spacecraft radiation effects assessment and serve as core specification for beamline terminal design.In the 300 MeV proton and heavy ion accelerator complex at the Space Environment Simulation and Research Infrastructure(SESRI),proton and heavy ion beams will be accelerated and ultimately delivered to three irradiation terminals.In order to achieve the required large irradiation area of 320 mm×320 mm,horizontal and vertical scanning magnets are used in the extraction beam line.However,considering the various requirements for beam species and energies,the tracking accuracy of power supplies(PSs),the eddy current effect of scanning magnets,and the fluctuation of ion bunch structure will reduce the irradiation uniformity.To mitigate these effects,a beam uniformity optimization method based on the measured beam distribution was proposed and applied in the accelerator complex at SESRI.In the experiment,the uniformity is successfully optimized from 75%to over 90%after five iterations of adjustment to the PS waveforms.In this paper,the method and experimental results were introduced.

Experimental Investigation of Particles Dynamics and Solid-Liquid Mixing Uniformity in a Stirred Tank

Particle suspension and deposition dynamics are significant factors affecting the level of mixing quality in solidliquid two-phase stirring processes. In general, the ability to increase the suspension rate and minimize depositioneffects is instrumental in improving the uniformity of particle mixing, accelerating the reaction of involved solidliquid two-phase, and improving the efficiency of production operations. In this work, suspension and depositionindicator based on the Betti number and a uniformity indicator are introduced and obtained by means of imageanalysis. The influence of the blade type, rotation speed, blade diameter and blade bottom height on the particlesuspension/deposition characteristics and mixing uniformity are carefully investigated. The experimental resultsshow that the two-phase motion region can be divided into three local regions, including a bottom motion alongthe wall, a low-degree suspension region under the blade and a high suspension region above the blade. The bestdegree of particle suspension is attained by the double-inclined blade paddle at a speed of 270 r/min, a paddlediameter ratio of 0.414, and a height-diameter ratio of 0.086. The double-inclined blade paddle has a better effecton promoting particle suspension and solid-liquid two-phase mixing uniformity.

Experimental Study on Gas Flow Uniformity in a Diesel Particulate Filter Carrier

A Diesel Particulate Filter(DPF)is a critical device for diesel engine exhaust products treatment.When using active-regeneration purification methods,on the one hand,a spatially irregular gas flow can produce relatively high local temperatures,potentially resulting in damage to the carrier;On the other hand,the internal temperature field can also undergo significant changes contributing to increase this risk.This study explores the gas flow uniformity in a DPF carrier and the related temperature behavior under drop-to-idle(DTI)condition by means of bench tests.It is shown that the considered silicon carbide carrier exhibits good flow uniformity,with a temperature deviation of no more than 2%with respect to the same radius measurement point at the outlet during the regeneration stage.In the DTI test,the temperature is relatively high within r/2 near the outlet end,where the maximum temperature peak occurs,and the maximum radial temperature gradient is located between r/2 and the edge.Both these quantities grow as the soot load increases,thereby making the risk of carrier burnout greater.Finally,it is shown that the soot load limit of the silicon carbide DPF can be extended to 11 g/L,which reduces the frequency of active regeneration by approximately 40%compared to a cordierite DPF.

Effects of external parameters on plasma characteristics and uniformity in a dual cylindrical inductively coupled plasma

The dual cylindrical inductively coupled plasma source,compared to the conventional structure of inductively coupled plasma source,can significantly improve the uniformity of plasma.It has an enhanced potential for application in processes,such as etching and ashing.A uniform plasma can be obtained by allowing the remote plasma from the upper chamber modulate the main plasma generated in the lower chamber.In this study,a fluid model was employed to investigate a dual cylindrical inductively coupled Ar/O_(2)discharge.The effects of external parameters on electron density,electron temperature,O atomic density,and plasma uniformity in the main chamber were studied,and the reasons were analyzed.The results of this study show that remote power can control the plasma uniformity and increase the plasma density in the main chamber.As the remote power increased,plasma uniformity improved initially and then deteriorated.The main power affected the plasma density at the edge of the main chamber and can modulate the plasma density in the main chamber.The gas pressure affected both the uniformity and density of the plasma.As the gas pressure increased,the plasma uniformity deteriorated,but the free radical density improved.

Effect of coil and chamber structure on plasma radial uniformity in radio frequency inductively coupled plasma

Enhancing plasma uniformity can be achieved by modifying coil and chamber structures in radio frequency inductively coupled plasma(ICP)to meet the demand for large-area and uniformly distributed plasma in industrial manufacturing.This study utilized a two-dimensional self-consistent fluid model to investigate how different coil configurations and chamber aspect ratios affect the radial uniformity of plasma in radio frequency ICP.The findings indicate that optimizing the radial spacing of the coil enhances plasma uniformity but with a reduction in electron density.Furthermore,optimizing the coil within the ICP reactor,using the interior point method in the Interior Point Optimizer significantly enhances plasma uniformity,elevating it from 56%to 96%within the range of the model sizes.Additionally,when the chamber aspect ratio k changes from 2.8 to 4.7,the plasma distribution changes from a center-high to a saddleshaped distribution.Moreover,the plasma uniformity becomes worse.Finally,adjusting process parameters,such as increasing source power and gas pressure,can enhance plasma uniformity.These findings contribute to optimizing the etching process by improving plasma radial uniformity.

Harmonic balance simulation of the influence of component uniformity and reliability on the performance of a Josephson traveling wave parametric amplifier

A Josephson traveling wave parametric amplifier(JTWPA),which is a quantum-limited amplifier with high gain and large bandwidth,is the core device of large-scale measurement and control systems for quantum computing.A typical JTWPA consists of thousands of Josephson junctions connected in series to form a transmission line and hundreds of shunt LC resonators periodically loaded along the line for phase matching.Because the variation of these capacitors and inductors can be detrimental to their high-frequency characteristics,the fabrication of a JTWPA typically necessitates precise processing equipment.To guide the fabrication process and further improve the design for manufacturability,it is necessary to understand how each electronic component affects the amplifier.In this paper,we use the harmonic balance method to conduct a comprehensive study on the impact of nonuniformity and fabrication yield of the electronic components on the performance of a JTWPA.The results provide insightful and scientific guidance for device design and fabrication processes.

Tent5c基因对斑马鱼肌间刺发育的影响

为探究tent5c/fam46c基因(Family with sequence similarity 46c,家族序列相似性46 c)在斑马鱼(Danio rerio)肌间刺发育中的作用,选取11种鱼类分析tent5c系统演化特征,采用原位杂交技术和qRT-PCR分析tent5c基因在斑马鱼发育中的时空表达特征,并利用CRISPR/Cas9建立了斑马鱼tent5c基因敲除纯合突变系(tent5c^(-/-)),对其骨骼表型和肌肉转录组进行分析。结果显示,tent5c编码TENT5C氨基酸在不同鱼类中具有高度的保守性,但在无肌间刺鱼类里发生了相同的氨基酸替换;tent5c基因在48hpf(Hours post fertilization)斑马鱼的眼睛和肌隔表达,在60dpf(Days post fertilization)斑马鱼的脊椎和肌间刺特异高表达。与野生型斑马鱼相比,tent5c^(-/-)斑马鱼肌间刺表现为生长减缓,矿化程度降低以及数量减少。比较转录组结果表明,在tent5c基因敲除之后,斑马鱼肌肉组织有112个基因表达下调,118个基因表达上调。差异基因主要富集于肌肉收缩和骨骼发育等相关通路,由此推测tent5c可能是通过调控这些肌肉和骨骼相关通路来对肌间刺发育产生影响。研究初步表明了tent5c基因在斑马鱼肌间刺发育中的作用,为进一步研究鱼类肌间刺等骨骼发育的分子调控机制提供了科学依据。

Demonstration of Center Pivot Uniformity Evaluation and Retrofit to Improve Water Use Efficiency

Agricultural irrigation is a primary user for freshwater withdrawal. Irrigation plays an important role in crop production, as it provides the benefit of reducing the effects of prolonged dryness and erratic precipitation. Center pivot irrigation system is the most common irrigation system in agriculture. As the center pivot irrigation system ages, the system could develop a leaking joint, clogged sprinklers, and physical damage. This can cause areas of non-uniformity that can lead to under- or over-irrigated in some areas of the land, resulting in excess energy use and cost, wasting resources, and environmental impacts. Thus, it is important to evaluate the performance of a center pivot irrigation system regularly to maximize return on investments and minimize wasting resources. This study focuses on evaluating the impacts and benefits of improved center pivot irrigation distribution uniformity by performing distribution uniformity evaluations pre- and post-retrofit. This study also focused on demonstrating an unmanned aerial vehicle (UAV) to assess the performance of the center pivot irrigation system in two irrigated farmlands. The Coefficient of Uniformity (CU), Distribution Uniformity (DU), and Scheduling Coefficient (SC) were calculated based on the catch can test data. The values were utilized to evaluate water and energy savings from the improved coefficients. The team has found that replacing sprinkler packages increased the CU from 78 to 89 and the DU from 77 to 82, and reduced the SC from 1.3 to 1.2 in Field A. In Field B, replacing sprinkler packages increased the CU from 73 to 91 and the DU from 62 to 84 and reduced the SC from 1.6 to 1.2. The estimated water savings in Field A due to the reduced scheduling coefficient was approximately 151,000 liters/hectare/year, with consideration of the corn and soybean rotation field in Michigan. The estimated water savings in Field B was 608,000 liters/hectare/year. The data from this demonstration study showed the value of distribution uniformity evaluation and retrofit of irrigation systems. This information will encourage farmers and agricultural industries to consider performing more distribution uniformity evaluations, ultimately improving irrigation water use efficiency and supporting sustainable water management in agriculture.

Experimental and numerical investigation on the uniformity of nanosecond pulsed dielectric barrier discharge influenced by pulse parameters

Nanosecond(ns)pulsed dielectric barrier discharge(DBD)is considered as a promising method to produce controllable large-volume and high activity low-temperature plasma at atmospheric pressure,which makes it suitable for wide applications.In this work,the ns pulse power supply is used to excite Ar DBD and the influences of the pulse parameters(voltage amplitude,pulse width,pulse rise and fall times)on the DBD uniformity are investigated.The gas gap voltage(Ug)and conduct current(Ig)are separated from the measured voltage and current waveforms to analyze the influence of electrical parameters.The spectral line intensity ratio of two Ar excited species is used as an indicator of the electron temperature(Te).The time resolved discharge processes are recorded by an intensified charge-coupled device camera and a one-dimensional fluid model is employed to simulate the spatial and temporal distributions of electrons,ions,metastable argon atoms and Te.Combining the experimental and numerical results,the mechanism of the pulse parameters influencing on the discharge uniformity is discussed.It is shown that the space electric field intensity and the space particles'densities are mainly responsible for the variation of discharge uniformity.With the increase of voltage and pulse width,the electric field intensity and the density of space particles increased,which results in the discharge mode transition from non-uniform to uniform,and then non-uniform.Furthermore,the extension of pulse rise and fall times leads to the discharge transition from uniform to nonuniform.The results are helpful to reveal the mechanism of ns pulsed DBD mode transition and to realize controllable and uniform plasma sources at atmospheric pressure.

Construction of Dynamic Alloy Interfaces for Uniform Li Deposition in Li-Metal Batteries

It is well accepted that a lithiophilic interface can effectively regulate Li deposition behaviors,but the influence of the lithiophilic interface is gradually diminished upon continuous Li deposition that completely isolates Li from the lithiophilic metals.Herein,we perform in-depth studies on the creation of dynamic alloy interfaces upon Li deposition,arising from the exceptionally high diffusion coefficient of Hg in the amalgam solid solution.As a comparison,other metals such as Au,Ag,and Zn have typical diffusion coefficients of 10-20 orders of magnitude lower than that of Hg in the similar solid solution phases.This difference induces compact Li deposition pattern with an amalgam substrate even with a high areal capacity of 55 mAh cm^(-2).This finding provides new insight into the rational design of Li anode substrate for the stable cycling of Li metal batteries.

Design and Structure Optimization of Plenum Chamber with Airfoil Baffle to Improve Its Outlet Velocity Uniformity in Heat Setting Machines

The plenum chamber of a heat setting machine is a key structure for distributing hot air to different air channels.Its outlet velocity uniformity directly determines the heating uniformity of textiles,significantly affecting the heat setting performance.In a traditional heat setting machine,the outlet airflow maldistribution of the plenum chamber still exists.In this study,a novel plenum chamber with an airfoil baffle was established to improve the uniformity of the velocity distribution at the outlet in a heat setting machine.The structural influence of the plenum chamber on the velocity distribution was investigated using a computational fluid dynamics program.It was found that a chamber with a smaller outlet partition thickness had a better outlet velocity uniformity.The structural optimization of the plenum chamber was conducted using the particle swarm optimization algorithm.The outlet partition thickness,the transverse distance and the longitudinal distance of the optimized plenum chamber were 20,686.2 and 274.6 mm,respectively.Experiments were carried out.The experimental and simulated results showed that the optimized plenum chamber with an airfoil baffle could improve the outlet velocity uniformity.The air outlet velocity uniformity index of the optimized plenum chamber with an airfoil baffle was 4.75%higher than that of the plenum chamber without an airfoil baffle and 5.98%higher than that of the conventional chamber with a square baffle in a commercial heat setting machine.

Hardy型Tent空间上乘积算子的有界性

研究Hardy型Tent空间上乘积算子M_(g)的有界性问题,借助序列型Tent空间的对偶性及分解定理,分情况给出所有参数0<p_(1),p_(2),q_(1),q_(2)<∞,α_(1),α_(2)>-n-1所对应的算子M_(g):HT_(q_(1),α_(1))^(p_(1))(B_(n))→HT_(q_(2),α_(2))^(p_(2))(B_(n))有界的连续型和离散型两种等价刻画.

基于Tent-ASO-BP的短期电力负荷预测模型

针对短期电力负荷预测精度低与可靠性差的问题,设计一种基于Tent-ASO-BP的电力短期负荷预测模型。该模型利用了Tent混沌映射的方法,设计了一种原子种群初始化方法,其在保证个体的同时选出适应度最优的个体,增强原子种群在分布空间的均匀性,进而加快ASO算法的收敛;同时引入自适应,增加该算法的局部探索和开发能力;将改进的ASO算法应用于BP神经网络参数优化,搭建了Tent-ASO-BP预测模型对短期电力负荷进行预测。使用Matlab工具进行仿真,通过对Tent-ASO-BP、ASO-BP和BP三种算法进行实验对比,结果表明,Tent-ASO-BP网络预测模型的RMSE、MAE和MAPE分别为32.736 MW,51.783 MW和6.623%,相比于ASO-BP和BP网络预测模型有明显减少,得出该模型具有更强的迭代能力和更强的局部寻优能力,为电力系统短期电力负荷预测提供依据,具有普遍的指导意义。

Low-Complexity Reconstruction of Covariance Matrix in Hybrid Uniform Circular Array

Spatial covariance matrix(SCM) is essential in many multi-antenna systems such as massive multiple-input multiple-output(MIMO). For multi-antenna systems operating at millimeter-wave bands, hybrid analog-digital structure has been widely adopted to reduce the cost of radio frequency chains.In this situation, signals received at the antennas are unavailable to the digital receiver, and as a consequence, traditional sample average approach cannot be used for SCM reconstruction in hybrid multi-antenna systems. To address this issue, beam sweeping algorithm(BSA) which can reconstruct the SCM effectively for a hybrid uniform linear array, has been proposed in our previous works. However, direct extension of BSA to a hybrid uniform circular array(UCA)will result in a huge computational burden. To this end, a low-complexity approach is proposed in this paper. By exploiting the symmetry features of SCM for the UCA, the number of unknowns can be reduced significantly and thus the complexity of reconstruction can be saved accordingly. Furthermore, an insightful analysis is also presented in this paper, showing that the reduction of the number of unknowns can also improve the accuracy of the reconstructed SCM. Simulation results are also shown to demonstrate the proposed approach.

On power series statistical convergence and new uniform integrability of double sequences

In the present paper,we mostly focus on P_(p)^(2)-statistical convergence.We will look into the uniform integrability via the power series method and its characterizations for double sequences.Also,the notions of P_(p)^(2)-statistically Cauchy sequence,P_(p)^(2)-statistical boundedness and core for double sequences will be described in addition to these findings.

基于GBDT特征提取与Tent-ASO-BP网络的铣刀磨损量预测

为了提高机械加工过程中小样本刀具磨损量监测的准确性,提出一种基于Pearson+GBDT特征提取、Tent混沌映射和原子搜索算法(ASO)优化BP神经网络(Tent-ASO-BP)的刀具磨损量预测模型。针对BP神经网络特征选择及参数选择难题,提出了基于Pearson+GBDT的双层过滤式特征筛选方式求取网络输入特征,并使用Tent混沌映射改进原子搜索算法(ASO)对BP神经网络最优权值和阈值进行求解。通过实验证明:Tent混沌映射改善了ASO,避免ASO陷入局部极值和过早收敛,即通过交叉验证证明Tent-ASO优化BP神经网络训练模型精度较ASO高。同时,验证了梯度提升决策树(GBDT)能够筛选出用于刀具磨损值映射的一组特征,且特征筛选能力强于同类算法Light GBM、Catboost、决策树、随机森林。

奇圈C_(5)的ℓ-uniform Ramsey数

研究ℓ-uniform Ramsey数R_(k)^(ℓ)(G),得到了R_(2)^(2)(C_(5))=R_(2)(C_(5))=9的结果.即确定了奇圈C_(5)的ℓ-uniform Ramsey数的精确值.