Solution of idle LBO problem for high FAR aero combustor

The paper sheds light on the idle lean blow off(LBO)problem for high fuel air ratio(FAR)com⁃bustor,which is impossible to be addressed with traditional aero combustor design.A significant improvement in aero combustor design is required to resolve the idle LBO issue.The authors detailed a practical and efficient solu⁃tion,which not only solved the idle LBO issue but also defined the aero-thermal design for high-FAR combustor.The design will usher in a new era of aero combustor.

Insights into some large-scale landslides in southeastern margin of Qinghai-Tibet Plateau

The southeastern margin of Qinghai-Tibet Plateau(SMQTP)is of a typical large landslide-prone area due to intense tectonic activity,deeply incised valleys,high geostress and frequent earthquakes.To gain insights into large landslides in southeastern margin of Qinghai-Tibet Plateau,an area covering 3.34×105 km2 that extends 80e150 km on both sides of the Sichuan-Tibet traffic corridors(G318)was used to examine the spatial distribution and corresponding characteristics of landslides.The results showed that the study area contains at least 629 large landslides that are mainly concentrated on 7 zones(zones IeVII).Zones IeVII are in the southern section of the Longmenshan fault zone(with no large river)and sections with Dadu River,Jinsha River,Lancang River,Nujiang River and Yarlung Zangbo River.There are more landslides in the Jinsha River section(totaling 186 landslides)than the other sections.According to the updated Varnes classification,408 large landslides(64.9%)were recognized and divided into 4 major types,i.e.flows(275 cases),slides(58 cases),topples(44 cases)and slope deformations(31 cases).Flows,which consist of rock avalanches and iceerock avalanches,are the most common landslide type.Large landslide triggers(178 events,28.3%)are also recognized,and earthquakes may be the most common trigger.Due to the limited data,these landslide type classifications and landslide triggers are perhaps immature,and further systematic analysis is needed.

Microstructure Characterization of the Fusion Zone of an Alloy 600-82 Weld Joint

Characterization of the microstructure of the fusion zone of an Alloy 600-82 weld joint was conducted, with focus on the weld residual strain distribution and the comparison of the microstructure of heat affected zone （HAZ） with that of cold worked alloy. Peak of the residual strain was observed to approach to the fusion boundary in HAZ while the strain increased from the top of the weld to the root. Strain distribution in the HAZ was found to be concentrated adjacent to grain boundaries （GBs）, with a peak of approximately three times of that in grain. Further, triple junctions of the GB appear to cause a higher strain concentration than single GBs. The microstructure of HAZ consists of partially tangled dislocations, which is different from slip bands of high density dislocations in cold worked alloy. This may cause a relatively higher intergranular cracking resistance of HAZ due to the difficulty in transferring tangled dislocations to GB in HAZ under deformation.

Nexus between the participation of residents in house design and residential satisfaction in Akure, Nigeria

This study examined the relationship between residents＇ level of participation in house design and level of residential satisfaction in Akure, Nigeria. The study was based on the idea that the goal of housing projects is to provide satisfactory environments for users. A cross-sectional survey was conducted on 304 household heads in transitional and peripheral zones of the city. Data were obtained through a structured questionnaire and focus group discussions and observations. The obtained data were subsequently subjected to single-factor descriptive analysis, mean satisfaction scoring, and categorical regression analysis. Results showed a positive significant relationship between the level of resident participation in house design and the level of residential satisfaction. The significant participatory predictors of satisfaction were number of bedrooms, general house design, development of the brief for the design, arrangement of interior spaces, and selection of finishing materials. Space size and building materials were not significant predictors in this context. The obtained p-value of 0.000 indicated that the regression model was significant. This study recommends a high level of resident participation in house design to achieve a high level of residential housing satisfaction in Nigeria.