Numerical investigation of temperature gradient-induced thermal stress for steel–concrete composite bridge deck in suspension bridges

A3D finite element model(FEM)with realistic field measurements of temperature distributions is proposed to investigate the thermal stress variation in the steel–concrete composite bridge deck system.First,a brief literaturereview indicates that traditional thermal stress calculation in suspension bridges is based on the2D plane structure with simplified temperature profiles on bridges.Thus,a3D FEM is proposed for accurate stress analysis.The focus is on the incorporation of full field arbitrary temperature profile for the stress analysis.Following this,the effect of realistic temperature distribution on the structure is investigated in detail and an example using field measurements of Aizhai Bridge is integrated with the proposed3D FEM model.Parametric studies are used to illustrate the effect of different parameters on the thermal stress distribution in the bridge structure.Next,the discussion and comparison of the proposed methodology and simplified calculation method in the standard is given.The calculation difference and their potential impact on the structure are shown in detail.Finally,some conclusions and recommendations for future bridge analysis and design are given based on the proposed study.

Improved methods for decreasing stresses of concrete slab of large-span through tied-arch composite bridge

Mechanical behavior of concrete slab of large-span through tied-arch composite bridge was investigated by finite element analysis (FEA). Improved methods to decrease concrete stresses were discussed based on comparisons of different deck schemes, construction sequences and measures, and ratios of reinforcement. The results show that the mechanical behavior of concrete slab gets worse with the increase of composite regions between steel beams and concrete slab. The deck scheme with the minimum composite region is recommended on condition that both strength and stiffness of the bridge meet design demands under service loads. Adopting in-situ-place construction method, concrete is suggested to be cast after removing the full-supported frameworks under the bridge. Thus, the axial tensile force of concrete slab caused by the first stage dead load is eliminated. Preloading the bridge before concrete casting and removing the load after the concrete reaching its design strength, the stresses of concrete slab caused by the second stage dead load and live load are further reduced or even eliminated. At last, with a high ratio of reinforcement more than 3%, the concrete stresses decrease obviously.

Internal Force Distribution in Steel-Concrete Composite Structure for Pylon of Cable-Stayed Bridge

Adopting a steel-anchor beam and steel corbel composite structure in the anchor zone on pylon is one of the key techniques for the design of Jintang bridge, a cable-stayed bridge in Zhoushan, China. In order to ensure the safety of the steel-concrete composite structure, a stud connector model for the joint section was put forward. Experiments were conducted to obtain the relation between load and slip of specimen, the failure pattern of stud connector, the yield bearing capacity and ultimate bearing capacity of a single stud, etc. The whole process of the structural behavior of the specimen was comprehensively analyzed. The features of the internal force distribution in the steel-concrete composite structure and the strain distribution of stud connector under different loads were emphatically studied. The test results show that the stud connector is applicable for the steel-concrete composite structure for pylon of Jintang bridge. The stud has a good ductility performance and a obvious yield process before its destruction. The stud connector basically works in a state of elasticity under a load less than the yield load.

Identification of Connection Flexibility Effects Based on Load Testing of a Steel-Concrete Bridge

In the case of composite girders, an effective cooperation of both parts of the section is influenced by deformability of connectors. Limited flexural stiffness of welded studs, used commonly in bridge structures, does not provide full interaction of a steel beam and a concrete slab. This changes strain distribution in cross-sections of a composite girder and results in redistribution of internal forces in steel and concrete element. In the paper partial interaction index defined on the basis of a neutral axis position, which can be used for verification of steel-concrete interaction in real bridge structures rather than in specimens is proposed. The range of the index value changes, obtained during load testing of a typical steel-concrete composite beam bridge, is presented. The investigation was carried out on a motorway viaduct, consisting of two parallel structures. During the testing values of strains in girders under static and quasi-static loads were measured. The readings from the gauges were used to determine the index, characterizing composite action of the girders. Results of bridge testing under movable load, changing position along the bridge span is presented and obtained in-situ influence functions of strains and index values are commented in the paper.

Mechanical behavior of concrete-filled rectangular steel tubular composite truss bridge in the negative moment region

Concrete-filled rectangular steel tubular(CFRST)composite truss bridge is a new type of structure composed of a CFRST truss and concrete deck slab.This new type of bridge has the advantages of high structural force-transferring efficiency,rapid assembly construction speed and excellent total life cycle,which meets the construction concept of green,recyclable and sustainable development.Due to the broad application prospects,experiment on the flexural behavior of CFRST composite truss bridge in the negative moment region was reported by authors previously.This paper thus presents a finite element analysis(FEA)modelling verified by the reported test data to further investigate the detailed analytical behavior of this structure.The structural response and failure mechanism of CFRST composite truss beam in the negative moment region are studied.In addition,the important structural design parameters on the flexural performance of the CFRST composite truss beam are also investigated,including the height to span ratio,the brace-to-chord wall thickness ratio,the reinforcement ratio of steel reinforcements and prestressed tendons and the strength grade of concrete infill in chords.Finally,the reasonable structural design parameters range are proposed for the optimum design of the CFRST composite truss bridge.

Timber-concrete composite bridges:Three case studies

During the last years, timber-concrete composite(TCC) structures have been extensively used in Europe both in new and existing buildings. Generally speaking, a composite structure combines the advantages of both materials employed: the strength and stiffness of the concrete in compression and the tensile strength, lightweight, low embodied energy, and aesthetical appearance of the timber. The concrete slab provides protection of the timber beams from direct contact with water, which is crucial to ensure the durability of the timber beams, particularly when used for bridges. Different types of connectors can be used to provide force exchange between the concrete slab and the timber beam. The choice of a structurally effective yet cheap shear connection between the concrete topping and the timber joist is crucial to make the TCC structures a viable solution that can compete with reinforced concrete and steel structures. In this paper, the possibilities offered by TCC structures for short-span bridge decks are discussed. The technology of TCC structures and the general design rules are illustrated. Three case studies are reported, including a short-span bridge tested in Colorado, USA, with the timber layer being constructed from recycled utility poles and notch connection; a TCC bridge with glulam beams and triangular notches with epoxyglued rebar connectors built in Portugal; and a TCC bridge with glulam beams and rectangular notches built in Germany. All the solutions were found to be structurally effective and aesthetically pleasing. They can all provide a sustainable option for short-span bridges.

Field validation of UHPC layer in negative moment region of steel-concrete composite continuous girder bridge

Improving the cracking resistance of steel-normal concrete(NC)composite beams in the negative moment region is one of the main tasks in designing continuous composite beam(CCB)bridges due to the low tensile strength of the NC deck at pier supports.This study proposed an innovative structural configuration for the negative bending moment region in a steel-concrete CCB bridge with the aid of ultrahigh performance concrete(UHPC)layer.In order to investigate the feasibility and effectiveness of this new UHPC jointed structure in the negative bending moment region,field load testing was conducted on a newly built full-scale bridge.The newly designed structural configuration was described in detail regarding the structural characteristics(cracking resistance,economy,durability,and constructability).In the field investigation,strains on the surface of the concrete bridge deck,rebar,and steel beam in the negative bending moment region,as well as mid-span deflection,were measured under different load cases.Also,a finite element model for the four-span superstructure of the full-scale bridge was established and validated by the field test results.The simulated results in terms of strains and mid-span deflection showed moderate consistency with the test results.This field test and the finite element model results demonstrated that the new configuration with the UHPC layer provided an effective alternative for the negative bending moment region of the composite beam.

The New Arched Bridge over Dnipro in Kyiv

The Podilskyi Arch bridge is crossing the Dnipro River in center of Kiev and is part of a 7.4 km long link which connects the center of Kiev with the “sleeping district” on the left bank of the river. The bridge has a main span of 344 m intended for six lanes of vehicles in the top level and two metro lines in the bottom level plus large diameter water pipes. The bridge is of steel, except of the reinforced concrete bases of the lower parts of the arches. The draft design works began in 1991 and in 2005 parallel design and construction work started. Due to the financial crisis in Ukraine, the work was interrupted for several years but construction recommenced in 2018 and the bridge is now planned to be completed in 2020 and the first stage of the transition in 2022.

开口断面钢-混结合梁悬索桥颤振特性及颤振形态研究

为准确评估开口断面双边箱钢-混结合梁悬索桥颤振性能和多模态参与效应,以典型的钢-混结合梁悬索桥——怀化洞庭溪沅水特大桥为背景,开展风洞模型试验及数值分析。制作加劲梁节段缩尺模型并进行风洞试验,测试原桥梁结构的颤振性能,分析调整阻尼比、采用气动措施及结构措施对结构颤振特性的影响,采用三维和二维两种颤振分析方法分析设置中央扣结构的颤振模态及多模态参与效应。结果表明:该钢-混结合梁悬索桥存在较明显的颤振起振点,且颤振是以扭转为主的弯扭耦合振动,同时其扭转和竖向振动存在较大的相位差(相差近180°);节段模型风洞试验与三维和二维颤振分析一致得到设置中央扣后,频率较高的正对称扭转模态先于反对称模态发生颤振,且三维与二维颤振分析结果相差不大。

钢-UHPC组合桥面板横向负弯矩区受弯性能研究

为明确横向负弯矩作用下,剪力键形式、接缝设置情形、配筋率和钢混界面黏结状态等参数对钢-超高性能混凝土(ultra-high-performance concrete,UHPC)组合板受力性能的影响,完成了8块组合板局部足尺模型静力弯曲试验及有限元参数分析。试验结果表明:开孔板(perfobond leiste,PBL)试件的名义开裂强度(对应最大裂缝宽度为0.05 mm)较栓钉试件提高16.8%;矩形齿缝试件的名义开裂强度较整浇试件降低16%~23%;UHPC层钢筋配筋率从1.96%增加到2.82%时,名义开裂强度提高16.2%;钢板-UHPC界面涂油除黏PBL试件的初裂强度和名义开裂强度较界面黏结试件分别降低10.1%和5.8%。数值分析结果表明:PBL贯穿钢筋的存在、PBL和栓钉间距的减小能有效提高组合板的开裂后刚度;PBL开孔钢板上的孔径和孔间距对组合板的受力性能影响较小。

钢-UHPC结合段PBL连接件和钢梁端面承压联合作用研究

钢-混结合段作为钢梁和混凝土连接为整体的核心部件,传力构件的受力性能对钢-混凝土结合段至关重要。为提高结合段的力学性能,进行了仅有钢梁端面承压、PBL连接件和两者联合作用3组推出试验。结果表明:3组试件最终破坏裂缝分布均为钢梁端面侧“八”字形分布;钢梁端面组(D组)试件破坏模式主要为UHPC的开裂破坏而失效,PBL连接件组(P组)和联合作用组(PD组)试件主要是贯穿钢筋的剪切破坏而失效;3组试件的荷载-滑移曲线均包含弹性、裂缝开展和屈服3个阶段,由于贯穿钢筋和UHPC榫具有抑制裂缝开展和提高试件延性的作用,P组和PD组试件裂缝开展阶段较D组更短,屈服阶段更长,延性更好。对荷载-滑移曲线进行拟合,提出了钢梁端面承压和PBL连接件承载力随滑移量变化的计算公式。引入滞后滑移差Δs_(j),当Δs_(j)=0~0.67 mm时,联合作用计算结果偏于安全。计算得到钢梁端面承压传力比例约为43%,PBL连接件传力比例约为57%,两者传力效果基本相当。利用UHPC作为外包混凝土时,建议采用承载能力更高的贯穿钢筋,以充分发挥UHPC的高强性能,从而提高结合段的承载能力。

钢-混组合桥梁栓钉腐蚀疲劳失效及力学性能退化机理试验研究

腐蚀环境中钢-混组合桥梁的栓钉连接件可能因腐蚀-疲劳耦合作用而劣化,为此设计制作3组10个栓钉推出试件,分别进行腐蚀后的静力、疲劳性能试验和腐蚀-疲劳耦合试验,研究栓钉的腐蚀-疲劳失效及力学性能退化机理。结果表明:腐蚀作用使得栓钉抗剪刚度显著退化;腐蚀-疲劳耦合作用下栓钉疲劳寿命明显低于腐蚀后疲劳寿命;栓钉初始疲劳裂纹产生于钉杆靠近焊趾截面的剪力作用侧,以剪切裂纹扩展为主,当疲劳裂纹或腐蚀疲劳裂纹发展至约1/2栓钉直径后,栓钉在拉-剪组合应力作用下断裂;影响栓钉损伤发展速率的主要因素为荷载比、腐蚀速率及腐蚀-疲劳耦合作用;腐蚀-疲劳耦合作用下栓钉抗剪刚度退化速度大于疲劳单独作用下,抗剪刚度退化包括快速退化和缓慢退化2个阶段,前一阶段约占栓钉腐蚀疲劳寿命的20%。

大跨度钢-混结合梁悬索桥涡激振动控制指标体系研究

为保证已建桥梁发生涡激振动后桥梁结构的安全以及桥上行车和行人安全,提出综合考虑人员舒适性、结构受力和停车线形三方面的大跨度钢-混结合梁悬索桥涡激振动控制指标体系。该体系包含9项指标,分别为驾乘人员舒适度、驾乘人员晕动症、行人舒适度(狄克曼指标)、加劲梁强度、加劲梁应力、加劲梁挠度、桥面纵坡、竖曲线半径和停车视距。以武汉鹦鹉洲长江大桥为背景,分别计算了“限速”和“封桥”2个交通管制措施下9项指标对应的涡激振动振幅限值。在此基础上,将9项指标对应的涡激振动振幅限值的最小值作为涡激振动限值建议取值。结果表明:当该桥发生低阶竖弯涡激振动(VS1、VAS1)时,涡激振动的控制因素为加劲梁挠度指标;当大桥发生VAS2模态的竖弯涡激振动时,涡激振动由驾乘人员晕动症指标和行人舒适度指标共同控制;当大桥发生高阶竖弯涡激振动(VAS3、VAS4)时,涡激振动由行人舒适度指标控制。涡激振动控制指标体系及限值标准的计算框架可适用于不同桥型涡激振动限值的计算。

简支波形腹板钢箱组合截面与传统截面箱梁桥抗震性能对比分析

为研究波形腹板钢箱-混凝土组合梁桥(CW-SBCCGB)与传统箱梁桥抗震性能的异同,基于截面等效原理,根据某实际工程CW-SBCCGB的单箱截面,等效出波形腹板混凝土箱梁桥(CW-CBGB)和混凝土箱梁桥(CBGB)的单箱截面,再结合动力分析理论和ABAQUS有限元模型对比分析3种截面简支梁桥动力特性和抗震性能的不同。结果表明:3种截面简支梁桥前五阶振型不变,CW-CBGB和CBGB前三阶频率相比于CW-SBCCGB有所下降,但相差不超过1Hz,第四阶及以后频率差异逐渐变大;剪滞效应对CW-SBCCGB和CW-CBGB动力特性影响较大,对CBGB影响较小;在纵桥向+竖桥向和横桥向+竖桥向地震作用下,CW-SBCCGB和CBGB的墩顶位移和跨中位移均大于CW-CBGB结构,CW-SBCCGB主梁跨中截面剪力最小,CW-CBGB跨中截面弯矩最小,说明CW-SBCCGB和CW-CBGB的抗震性能均优于CBGB的抗震性能。

公铁合建斜拉桥钢桁-混凝土板组合梁受力特性

以某主跨808 m的公铁合建新型钢桁-混凝土板组合梁斜拉桥为背景,采用ANSYS软件建立局部组合梁细化的全桥多尺度有限元模型,分析其在不同工况下双层组合梁的受力传力特性和混凝土桥面板荷载分配比,并讨论混凝土桥面板厚度t_(b)、横梁刚度变化系数λ_(K)和钢与混凝土弹性模量比λ_(E)对组合梁受力传力的影响规律。结果表明:最不利组合工况下,钢桁架最不利Von Mises应力为183.6 MPa,混凝土桥面板最大拉应力为5.3 MPa,均满足结构受力要求;沿纵向路径,钢桁架和混凝土桥面应力在节间横梁间均呈“波形”分布;上下层混凝土桥面板顶、底面应力沿横向近似呈“W”和“M”状分布,表明桥面板承受一定沿横向不均匀分布弯矩;公路及铁路混凝土桥面最大剪力滞系数分别为1.45、1.36,更宽的公路混凝土桥面剪力滞效应更显著;公路及铁路混凝土桥面分别承担上、下层结构57.46%~79.99%和33.21%~62.81%的轴向荷载,为组合梁的主要传力构件;混凝土桥面板的应力随t_(b)及λ_(K)的增大而增大,随λ_(E)的增大而逐渐减小;混凝土桥面每层平均荷载分配比ξ与t_(b)成正比,与λ_(K)及λ_(E)成反比;当t_(b)、λ_(K)和λ_(E)参数的取值范围分别为0.8~1.4、0.4~1.6以及4~10时,组合梁混凝土桥面应力及荷载分配比ξ较为合理。

双工字钢板组合梁桥的时变体系冗余性评估

为评估双工字钢板组合梁桥应对非对称极端作用的时变体系冗余性,采用数值增量算法,开展了双工字钢板组合梁桥非对称荷载下的弹塑性全过程分析.提出了基于弹塑性累积应变能的构件承载贡献率指标,研究了双工字钢板组合梁桥时变体系冗余性的影响因素及变化规律,揭示了双工字钢板组合梁桥冗余性不足的内在原因.结果表明:横向刚度和主梁延性是影响钢板组合梁桥体系冗余性的主要因素,横向传力刚度越大,主梁延性越高,则结构体系冗余性越强;与典型多主梁体系相比,双工字钢板组合梁桥的横向传力刚度降低约24%,导致结构冗余度降低约55%;材料劣化引起的主梁延性退化会导致冗余度在寿命周期最大下降约25%.

马鞍山长江公铁大桥主航道桥中塔下横梁施工关键技术

马鞍山长江公铁大桥主航道桥Z4号中塔采用空间四肢A形钢-混组合塔,横向两塔肢间设下横梁,下横梁间设3道系梁,纵向两塔肢间不设置横梁。下横梁采用支架法分层浇筑施工。下横梁施工支架采用落地式钢管支架配套模板体系,受力性能满足要求;通过有限元计算比选下横梁混凝土分层浇筑方案并进行优化,采取(5.5+2.5)m分层方案,上、下层混凝土分别分为2块、3块分层分块浇筑;通过低温升、易泵送、高抗裂的C60混凝土研制、下横梁与塔柱倒弧结合面抗裂措施优化、分块间接缝构造形式及施工工艺优化、下横梁与系梁混凝土浇筑施工组织优化、混凝土温度智能化监控、预应力束张拉时机控制等混凝土防裂措施,有效解决了下横梁大体积混凝土易开裂的难题。

大跨环形矮塔斜拉桥主塔力学性能分析

以大跨度环形矮塔斜拉桥的主塔为研究对象,借助大型有限元程序midas进行了静力及地震动时程分析,通过提取杆系模型中的最不利内力,对索塔锚固区及下塔柱钢混结合段空间应力进行分析。结果表明:1)钢塔在静力及地震工况下强度及稳定均满足要求;2)索塔锚固区及钢混结合段应力状态良好、构造细节处理较为合理。

钢-混凝土组合简支桥面连续结构横向应力分析

针对钢-混组合简支梁桥的桥面连续结构开裂等病害,围绕桥面连接板的横桥向应力问题,采用线弹性理论和板的偏微分方程进行分析,得出了桥面连接板挠度和应力的分布函数,建立非线性有限元模型,并进行实桥荷载试验.通过比较理论解、有限元解和实测试验结果,证实了理论解和有限元的有效性.根据得到的分布函数,发现横桥向和纵桥向上的最大拉应力出现在钢梁端部位置的连接板的上缘.此外,还分析了连接板区域尺寸变化对横桥向应力峰值的影响,包括纵梁端部距支座的长度、纵梁的间距以及连接板区域整体尺寸变化.结果表明:较小的纵梁间距和较长的纵梁端部与支撑之间的距离会导致连接板中的横向拉应力峰值增加,并提高横向拉应力在总应力中的占比,从而导致桥面连接板早于设计荷载开裂.因此对于纵梁间距较小、梁端长度较长的钢-混组合简支梁桥桥面连续结构,仅计算其纵桥向受力性能会导致计算结果偏危险,建议按照本文方法考虑横桥向应力对桥面连接板的影响.

常泰长江大桥组合索塔锚固结构钢-混传剪构造足尺模型试验研究

常泰长江大桥索塔锚固结构采用钢箱-核芯混凝土组合结构,为研究该新型组合索塔锚固结构钢-混传剪构造的受力特性,进行钢-混传剪构造足尺模型试验研究。制作2个锚固结构足尺节段试验模型,通过压剪试验研究锚固结构的荷载~滑移曲线及应力、应变分布等受力特性,并通过有限元模型分析锚固结构的传力机理和各组件的内力分配比例,推导剪力钉剪力计算方法。结果表明:在2.14倍单索最大索力荷载作用下,锚固结构保持弹性状态,钢壁板未产生明显滑移,钢-混界面最大滑移不超过0.25 mm,该锚固结构中钢-混传剪构造至少具有2.14倍的安全系数;荷载作用下,剪力钉剪力从上至下逐渐增大,锚腹板附近底部3排剪力钉剪力较大,钢-混传剪构造至少存在剪力钉和界面摩擦力2种传剪机制,钢-混传剪构造的承载能力显著提高;钢-混传剪构造受力过程分为粘结力传力阶段和局部滑移阶段,剪力钉剪力分布不仅与沿剪切方向长度分布有关,也与荷载的大小线性相关。