Application of Large-diameter and Long-span Micro-expansive Pumping Concrete Filled Steel Tube Arch Bridge

In this article the high strength micro-expansive concrete that has been applied on big-diameter and long-span steel arch bridge is researched. The applications show that the concrete has some merits, such as good fluidity, low bleeding ratio and no segregation, low slump loss, high early strength and high later strength, micro-expansion etc.

Approach for analyzing the ultimate strength of concrete filled steel tubular arch bridges with stiffening girder

A convenient approach is proposed for analyzing the ultimate load carrying capacity of concrete filled steel tubular (CFST) arch bridge with stiffening girders. A fiber model beam element is specially used to simulate the stiffening girder and CFST arch rib. The geometric nonlinearity, material nonlinearity, influence of the construction process and the contribution of prestressing reinforcement are all taken into consideration. The accuracy of this method is validated by comparing its results with experimental results. Finally, the ultimate strength of an abnormal CFST arch bridge with stiffening girders is investigated and the effect of construction method is discussed. It is concluded that the construction process has little effect on the ultimate strength of the bridge.

Seismic behavior of concrete filled steel tubular arch structures

Shaking table tests of a 1:10 scale arch model performed to investigate the seismic behavior and resistance of concrete filled steel tubular (CFT) arch structures are described in this paper. The El-Centro record and Shanghai artificial wave were adopted as the input excitation. The entire test process can be divided into three stages depending on the lateral brace configurations, i.e., fully (five) braced, two braces removed, and all braces removed. A total of 46 tests, starting from the elastic state to failure condition, have been conducted. The natural vibration frequencies, responses of acceleration, displacement and strain were measured. From the test results, it is demonstrated that the CFT arch structures are capable of resisting severe ground motions and that CFT arches offer a credible alternative to reinforced concrete arches, especially in regions of high seismic intensity.

Experimental investigation of axially loaded steel fiber reinforced high strength concrete-filled steel tube columns

An experimental study on the compressive behavior of steel fiber reinforced concrete-filled steel tube columns is presented. Specimens were tested to investigate the effects of the concrete strength, the thickness of steel tube and the steel fiber volume fraction on the ultimate strength and the ductility. The experimental results indicate that the addition of steel fibers in concrete can significantly improve the ductility and the energy dissipation capacity of the concrete-filled steel tube columns and delay the local buckling of the steel tube, but has no obvious effect on the failure mode. It has also been found that the addition of steel fibers is a more effective method than using thicker steel tube in enhancing the ductility, and more advantageous in the case of higher strength concrete. An analytical model to estimate the load capacity is proposed for steel tube columns filled with both plain concrete and steel fiber reinforced concrete. The predicted results are in good agreement with the experimental ones obtained in this work and literatures.

Quantifying Creep of Concrete Filled Steel Tubes

Using age adjusted effective modulus(AAEM)method,creep of concrete filled steel tube(CFST)member was formulated considering of creep coefficient and aging coefficient.Ten CFST specimens were tested including eight for creep and two for shrinkage.The experimental result was compared with the computed result using AAEM in which the creep coefficient was taken from calibration of ACI model based on experimental result on sealed concrete,and aging coefficient was supplied from relaxation test on sealed concrete specimen.Furthermore,the creep of CFST member was analyzed using author's own subroutine to input concrete properties through user programmable feature(UPF)in ANSYS software.Comparison was made on authors' own experimental database,some existing experimental results,and results from AAEM and numerical analysis.Finally,the conditions of applicability of AAEM method are put forward,and numerical approach to compute creep of CFST specimen is delineated.

In-Plane Creep Buckling of Concrete-Filled Steel Tubular Arches

The creep-induced deformation of the arch rib of concrete-filled steel tubular(CFST) arches under a sustained load can increase the bending moment, which may lead to earlier stability failure called creep buckling. To investigate the influences of concrete creep on the buckling strength of arches, a theoretical analysis for the creep buckling of CFST circular arches under distributed radial load is performed. The simplified Arutyunyan-Maslov(AM)creep law is used to model the creep behavior of concrete core, and the creep integral operator is introduced. The analytical solutions of the time-dependent buckling strength under the sustained load are achieved and compared with the existing formula based on the age-adjusted effective modulus method(AEMM). Then the solutions are used to determine the influences of the steel ratio and the first loading age on the creep buckling of CFST arches. The results show that the analytical solutions are of good accuracy and applicability. For CFST arches, the steel ratio and the first loading age have significant influences on creep buckling. An approximate log-linear relationship between the decreased degrees of the creep buckling strength and the first loading age is found. For the commonly used parameters, the maximum loss of the buckling strength induced by concrete creep is close to 40%.

Axial Bearing Capacity of Short FRP Confined Concrete-filled Steel Tubular Columns

The bearing capacity of FRP confined concrete-filled steel tubular （FRP-CFST） columns under axial compression was investigated. This new type of composite column is a concrete-filled steel tube （CFST） confined with fiber-reinforced polymer （FRP） wraps. Totally 11 short column specimens were tested to failure under axial compression. The influences of the type and quantity of FRP, the thickness of steel tube and the concrete strength were studied. It was found that the bearing capacity of short FRP-CFST column was much higher than that of comparable CFST column. Furthermore, the formulas for calculating the bearing capacity of the FRP-CFST columns are proposed. The analytical calculated results agree well with the experimental results.

基于互信息和MiniRocket网络的CFST脱空识别

为提高钢管混凝土(concrete filled steel tube,CFST)脱空检测的效率和精度,本文提出了一种基于快速傅里叶变换(fast fourier transform,FFT)、互信息(mutual information,MI)和MiniRocket神经网络的智能识别方法。首先,采用FFT将待测CFST敲击声波时域信号转换为频域信号;其次,采用MI建立频域信号与脱空状态的相关性,提取相关性最大的前30个特征建立数据集,避免了复杂的数学运算和冗余信息;建立MiniRocket深度学习网络,通过使用更少的参数量和更小的特征尺寸,提高分类的速度和精度。最后,考察了模型的噪音鲁棒性,并与其他算法、特征提取方法和识别方法进行对比。结果表明,在不同脱空深度和脱空宽度下,所提的方法在100次重复试验中获得了100%的平均预测精度。在高信噪比下,该方法受影响较小。此外,与其他算法、特征提取方法和识别方法相比,本方法具有更好的预测性能。因此,所提出的方法在未来实际CFST结构的智能脱空识别中具有较大的应用潜力。

温度效应对CFST拱桥拱肋预拱度取值影响的探讨

为探讨制作温差对拱肋预拱度取值的影响,以某主跨528 m的中承式钢管混凝土拱桥为依托背景,利用MIDAS/civil建立有限元仿真模型,分析了五个不同制作温差梯度对拱肋成拱线形的影响。计算结果表明:当拱肋制作温差与设计基准温度相差较大时,原设计预拱度可能存在设置不足的情况,建议拱肋预拱度取值应计入拱肋制作温差对成拱线形的影响。此外,依据9座钢管混凝土拱桥实例,在有限元计算结果的基础之上结合Plane函数和Levenberg-Marquardt优化算法,得到了单位环境变温与空钢管状态下拱顶挠度间的显式函数关系式。

超大跨CFST拱桥管内混凝土灌注方案比选研究

为探讨扣索调载对拱肋混凝土灌注过程的影响,以某跨径575 m的中承式钢管混凝土拱桥为工程背景,采用MIDAS/Civil建立空间有限元模型对比分析大桥管内混凝土考虑过程调载和不调载两种灌注方案。结果表明:过程考虑调整,能有效抑制拱肋1号—8号节段下挠,9号—11号节段上挠,以及控制拱肋横向偏位的发展;两种方案下,管内混凝土最大拉应力都能满足抗拉强度设计要求,但过程调整管内混凝土最大拉应力能有效降低76%。

考虑上部质量的双柱CFST桥墩抗车辆撞击力学性能研究

钢管混凝土(CFST)构件可充分发挥钢管与核心混凝土优点,在桥梁墩柱中已得到应用,抗撞设计是其在墩柱中推广应用的关键问题。因此,该文基于LS-DYNA有限元软件建立了56个车辆撞击双柱CFST桥墩分析模型并进行抗撞机理与参数分析。基于前期落锤撞击结果与实车撞击试验验证了模型可靠性;对典型工况下撞击力和桥墩塑性应变发展、内力分布和能量转换进行研究并重点分析了含钢率、轴压比、货物刚度、车辆质量和速度对CFST桥墩撞击力和侧向位移分布的影响规律;采用等效静力法计算得到25 ms等效车辆撞击力(ESF25)并对AASHTO规程建议值进行评估,提出车撞CFST桥墩撞击力预测公式。结果表明:车辆撞击下CFST桥墩钢管与核心混凝土协同工作,钢管是主要耗能部件;由于上部结构和桥墩惯性作用,不同撞击时刻桥墩内力分布具有显著差异;车辆质量与速度对撞击力发展影响显著,含钢率与轴压比影响较小,货物弹性模量在2000 MPa内变化时影响较大;建议的撞击力公式可较好预测考虑上部质量影响的CFST桥墩撞击力。

Analysis and seismic tests of composite shear walls with CFST columns and steel plate deep beams

A composite shear wall concept based on concrete filled steel tube （CFST） columns and steel plate （SP） deep beams is proposed and examined in this study. The new wall is composed of three different energy dissipation elements： CFST columns; SP deep beams; and reinforced concrete （RC） strips. The RC strips are intended to allow the core structural elements - the CFST columns and SP deep beams - to work as a single structure to consume energy. Six specimens of different configurations were tested under cyclic loading. The resulting data are analyzed herein. In addition, numerical simulations of the stress and damage processes for each specimen were carried out, and simulations were completed for a range of location and span-height ratio variations for the SP beams. The simulations show good agreement with the test results. The core structure exhibits a ductile yielding mechanism characteristic of strong column-weak beam structures, hysteretic curves are plump and the composite shear wall exhibits several seismic defense lines. The deformation of the shear wall specimens with encased CFST column and SP deep beam design appears to be closer to that of entire shear walls. Establishing optimal design parameters for the configuration of SP deep beams is pivotal to the best seismic behavior of the wall. The new composite shear wall is therefore suitable for use in the seismic design of building structures.

Simplified Algorithm for Out-of-Plane Critical Loads of CFST Solid-Rib Arch

The simplified algorithm for out-of-plane ultimate loadcarrying capacity of concrete-filled steel tubular( CFST) solid-rib arches under uniform vertical load was studied. The experimentally validated finite element model was developed. The out-of-plane equivalent length coefficients of solid-rib arches were obtained using out-of-plane elastic eigenvalue buckling analysis. Then the out-ofplane elastic stability coefficient was plotted against the normalized slenderness ratio,and the out-of-plane eigenvalue buckling load or elastic buckling capability of arches was calculated. Lastly effects of different parameters on the out-of-plane ultimate load-carrying capacity of CFST solid-rib arches were determined using geometric and material nonlinear finite element analysis, and a simplified algorithm was established by fitting the out-of-plane elastic-plastic stability coefficient and normalized slenderness ratio using PerryRobertson formula. Ratio of the elastic stability coefficient to the elastic-plastic counterpart was plotted against the out-of-plane normalized slenderness ratio,from which the out-of-plane elasticplastic ultimate load-carrying capacity was determined according to the corresponding elastic buckling load. Results show that the proposed simplified algorithm can accurately predict the out-of-plane eigenvalue buckling load and the elastic-plastic ultimate loadcarrying capacity of the CFST solid-rib arches.

大跨CFST拱桥拱轴线形的综合评分法

为探究500m级钢管混凝土拱桥拱轴线形的合理程度,从钢管混凝土拱桥成桥状态的强度、刚度、稳定性和拱轴线形优化方法的操作复杂性角度,对各最优拱轴线形进行拱轴线形评判指标计算对比,提出一种可用于定量评判钢管混凝土拱桥拱轴线形的优化程度的方法——钢管混凝土拱桥拱轴线形优化综合评分法(CFST-ARO综合评分法)。文中以波司登大桥为工程实例,对经优化后的抛物线、悬链线及三次样条曲线拱轴线形采用综合评分法进行定量评定。结果表明选用3次样条插值函数优化的拱轴线形内力状态优化效果显著,沿跨径方向应力幅度比其他曲线小且均匀,刚度和稳定性都有所提高;以期为同类型拱桥拱轴线形优化评价提供科学参考。

瓮马铁路乌江特大桥设计关键技术研究

新建瓮马铁路乌江特大桥跨越两山之间深谷,地形复杂、设计难度大。为研究该桥梁方案,首先阐述了主桥的方案构思和结构设计,然后通过空间有限元软件对本桥进行静、动力仿真分析,总结了大跨铁路劲性骨架混凝土拱桥构造和受力特性。结果表明:主跨337 m上承式劲性骨架混凝土拱桥具有刚度大、徐变小、后期养护维修工作量小等优点,主拱圈采用小矢跨比设计,兼顾安全、经济、环保和美观,能够满足铁路桥梁跨越山区“V”形峡谷的要求;主拱圈由劲性钢管混凝土骨架外包C55无收缩混凝土构成,通过分层分段浇筑方案改善拱圈各构件的内力;拱上结合梁采用两片工字形钢与混凝土桥面板相结合的形式,钢梁栓焊结合,便于制造、运输和施工;拱座采用梯形断面扩大基础,基础开挖永临结合,有效降低施工风险;数值分析表明该桥结构的刚度、强度、稳定性均能满足规范要求,能够满足客货共线铁路的安全性和乘坐舒适性要求。可为其他山区铁路桥梁桥式研究提供参考。

曲线条件大跨度拱加劲连续梁设计

贵南高铁二塘双线特大桥采用90m+180m+90m拱加劲连续梁结构。大桥位于曲线上,梁体采用分段直线布置,悬灌施工;主拱采用哑铃形钢管混凝土拱肋,钢管直径1 m,拱肋全高3 m;采用整束挤压钢绞线吊杆,全桥拱设置36组吊杆;纵向活动主墩通过构造措施,形成半刚构结构体系,限制部分梁体问题伸缩变形;大桥采用先悬灌主梁,后在主梁上搭设支架原位拼装拱肋方式施工。经论文研究计算结果表明,该桥刚度、受力等均满足规范要求。

Experimental research on self-stressing and self-compacting concrete filled steel tube columns subjected to eccentric load

A total of fifteen self-stressing and selfcompacting concrete(SSC)filled steel tube columns and three common self-compacting concrete filled steel tube(CFST)columns are tested under eccentric compression load to analyze the the effect of initial self-stress on the compression behavior of CFSTs.The results show that the elastic working range of the columns is lengthened because of initial self-stress and it slightly decreases with the increase of load eccentricity ratio and slenderness ratio.Because of the initial self-stress,the concrete core is always under compression in three directions,so the compactness is enhanced and the ultimate bearing capacity obviously increases;but the initial self-stress hardly affects the failure mode of the columns.

近断层地震作用下大跨CFST拱桥的动力稳定性

为研究大跨度CFST(钢管混凝土)拱桥在近断层地震作用下的动力稳定性能,以主跨132 m的下承式钢管混凝土拱桥为工程背景,以台湾集集地震记录作为横向输入,采用动态增量分析(IDA)方法,对动力失稳临界荷载的确定进行了探讨.为提高IDA的分析效率,采用了高性能数值计算并行处理方法.此外,还讨论了加强IDA曲线簇收敛的问题.结果表明:脉冲型近震可导致非线性极值动力失稳,失稳临界荷载明显降低;采用加权平均加速度峰值作为地震强度指标,能显著改善IDA曲线簇的离散性,有利于揭示近断层地震对钢管混凝土拱桥造成动力失稳的特点.