Basic Physical Characteristics of the Water-permeable Brick with Composite Structure

The resin-sand mixture was proposed to be used as the surface course,and cement permeable concrete was used as the base course;such two kinds of materials were combined to prepare water-permeable brick with a composite structure.The compressive strength,flexural strength,and permeability were studied by using adjusting the contents of carbon fiber,quartz powder,cement,sand,and surfactant.The study shows that the hydrophilicity of the resin-sand mixture can be improved after any amount of resin is replaced by quartz powder;by using the surfactant,the interface energy of the particles can be reduced so that the water permeability of the surface course can be promoted effectively.However,the mechanical properties of the surface course were negatively affected by the surfactant.With the optimal process consideration in the experiments,the properties about compressive strength,flexural strength,and permeability of the composite permeable brick can meet the requirements of the specifications of resin-sand based water permeable brick JGT 376-2012(compressive strength was higher than 35 MPa,the flexural strength exceeded 5.19 MPa,and the average permeability coefficient was higher than 2.3×10^(-2)cm/s).There are no obvious pores on the surface course and only water molecules can pass through it,therefore,the surface of the permeable brick cannot be blocked up by solid substances,and the permeability of such permeable brick can be improved effectively in this way.

Properties Evaluation of Concrete using Local Used Bricks as Coarse Aggregate

With time concrete / reinforced concrete has become the popular material for construction. Modern industry utilizes this material a lot and has produced various beautiful, eye catching and amazing structures. Due to modern requirements for living and developed construction industries, the old buildings (usually constructed with brick masonry) are demolished and are replaced with new modern buildings. Demolition of buildings results in waste materials which can create waste related problems and environmental issues. By using recycled aggregates weight of concrete can also be reduced, which can also solve problems related to self-weight of concrete. In this paper attempt has been made to use local used bricks from vicinity of Nawabshah, Pakistan, as coarse aggregate. Concrete cubes made with local recycled bricks are cast and tested for overall weight of concrete, moisture content, dynamic modulus of elasticity and compressive strength (nondestructive and destructive methods). The results showed that concrete derived from recycled aggregates attained lower strength than regular concrete. More detailed elaborated work is recommended with different mix ratios and different proportions recycled aggregates for better conclusions.

Crack Propagation and Failure Characteristics of Modeled Concrete with Natural and Brick Aggregates

The failure characteristics of recycled concrete containing brick aggregates are still indistinct,especially how the angular aggregates effect the crack propagation.Based on the concept of modeled concrete,the development of cracks in concrete containing the natural aggregate and brick aggregate under a compression loading was studied.The strain distribution was analyzed with the Digital Image Correlation(DIC).The modeled aggregates include circular and squared ones,and the squared modeled aggregates were placed in different orientations,including 0°,22.5°and 45°.The results show that when the aggregate is placed at 45°,the upper and lower vertices of the aggregate lead to the highest critical strain concentration,therefore,cracks are easy to propagate from these areas and the strength of the corresponding modeled concrete is the lowest.When the modeled natural aggregate is placed at the orientation of 0°,the strain concentration first appears at the interface on both lateral sides of the aggregate.The brick aggregate has a lower elastic modulus and strength than the surrounding mortar.As a result,cracks always propagate through the brick aggregate,which is the primary reason for the low strength of the corresponding concrete.

Application of Fractal Theory in Brick-Concrete Structural Health Monitoring

In order to monitor and forecast the deformation of the brick-concrete building, by taking a brick-concrete building as research object, fiber grating sensors were used to collect the monitoring data and double logarithmic curve of limit value characteristic and monitoring data were obtained based on the fractal theory. Constant dimension fractal method cannot be used to analyze the data directly. With the method of variable dimension fractal, we accumulate data, and the double logarithmic curve is smooth. Piecewise fractal dimensions are close. The outer interpolation method is used to calculate the fractal dimension of the next point and then back calculate the vertical displacement. The relative errors are calculated by comparing the forecast values and monitoring values, and the maximum relative error is 5.76%. The result shows that the fractal theory is suitable to use in the forecast of the deformation and the accuracy is good.

Flexural Behavior of Cross-Connected Brick Masonry Infill Wall Panels Supported on Reinforced Concrete Beam Grids

This paper presents an experimental investigation on the flexural behavior of cross-connected brick masonry infill wall panels supported on reinforced concrete beam grids above and below the walls.The experimental program was comprised of six wall systems.The effect of change in lower beam stiffness relative to the wall and the geometry of the main walls were investigated.From the results of the experimental tests,the increase in the depth of the lower beam grid reduces the deflection,resulting in an increase in the load carrying capacity of the wall.Further,the stiffness of the main walls affects the deflection and the failure load of the cross walls.

Analytical study of performance evaluation for seismic retrofitting of reinforced concrete building using 3D dynamic nonlinear finite element analysis

This paper presents three-dimensional finite element （FE） analyses of an all-frame model of a three-story reinforced concrete （RC） building damaged in the 1999 Taiwan Chi-Chi Earthquake. Non-structural brick walls of the building acted as a seismic resistant element although their contributions were neglected in the design. Hence, the entire structure of a typical frame was modeled and static and dynamic nonlinear analyses were conducted to evaluate the contributions of the brick walls. However, the results of the analyses were considerably overestimated due to coarse mesh discretizations, which were unavoidable due to limited computer resources. This study corrects the overestimations by modifying （1） the tensile strengths and （2） shear stiffness reduction factors of concrete and brick. The results indicate that brick walls improve frame strength although shear failures are caused in columns shortened by spandrel walls. Then, the effectiveness of three types of seismic retrofits is evaluated. The maximum drift of the first floor is reduced by 89.3%, 94.8%, and 27.5% by Steel-confined, FuI1-RC, and Full-brick models, respectively. Finally, feasibility analyses of models with soils were conducted. The analyses indicated that the soils elongate the natural period of building models although no significant differences were observed.

Study on Performances of the Concrete Pavement from Zincilate

The use of zincilate production of concrete pavement brick both use of industrial solid waste, protect the environment and promoting building energy efficiency, there are huge comprehensive benefits. Based on the guizhou bijie zincilate as the main raw material preparation from concrete pavement brick, and the main factors which influence the quality of the products was investigated. The test results show that: Concrete pavement brick compressive strength at 28 days with zinc slag volume increases, zinc slag admixture is 40%, 28 days compressive strength is more than 32 MPa.

Effect of Clay Fines on the Behavior of Self-Compacting Concrete

The technology of concrete has significantly increased in recent years through the use of super plasticizer and availability of mineral additions. One of the most recent materials used as an additive, replacing a portion of cement in concrete, is fine clay fired at a temperature of 800℃ to 900℃. This research is based on trials that complied with artificial pozzolan (waste crushed brick), and their effect on the rheological and mechanical behavior of mortar. The addition of 5% of a waste crushed brick has helped not only to improve the strength (tensile and compression), but also to foster a better rheological behavior in terms of fluidity and stability, with a low heat of hydration compared to control. However, tests of optimizing the content of self-compacting concrete (SCC) in coarse aggregates, sand and binder, led us to confirm that the combined mass of more optimal (better workability and stability) is that based on low in volumetric percentage of sand/paste with a granular skeleton richest gravel low dimensions (2/3 of G 3/8 and 1/3 of G 8/15).

Influence of Recycled Construction Materials Aggregate on Mechanical and Physical Properties of Concrete

The main purpose of this research is to study the properties of re-use different types of construction materials such as PVC （polyvinylchloride） scraps, clay brick and recycled concrete as a partial replacement of coarse aggregate. Different proportions （1%, 3%, 5% and 7%） by weight were used for PVC. scrap, （10%, 20%, 30%, and 40%） by weight were used for recycled concrete and （5%, 10%, 15%, and 20%） by weight were used for clay brick. Mechanical tests such as compressive and tensile strength tests and physical tests such as ultrasonic pulse velocity, bulk density, porosity, specific gravity and water absorption tests were done to the samples after curing in normal water for 28 days. Test results showed slightly degradation in mechanical and physical engineering properties of concrete specimens that used partial replacement of recycled concrete coarse aggregate, degradation increased with increasing of replacement but test results still closely to reference samples. Use of polyvinyl chloride in proportions not more than 5% as a partial replacement of coarse aggregates given acceptable results in comparison with reference samples but all test results degraded at 7% replacements. Test results of partial replacement of crushed brick coarse aggregates unacceptable and the range of degradation are wide because of increased （water： cement） ratio to improve the concrete workability.

高延性混凝土加固单层砖木结构农房振动台试验研究

为提高我国农村砌体房屋的抗震性能水平,采用高延性混凝土(HDC)条带加固的方法,设计了两个缩尺比为1∶2的砖木结构模型,对加固模型与未加固模型进行振动台同台对比试验。对比分析了地震作用下两个模型结构的加速度响应、位移响应、扭转效应和破坏形态,并对其抗震性能进行评估。试验结果表明:单层砖木结构农房的整体抗震性能较差,结构的自振频率低、位移反应较大,扭转效应明显,在8度设防地震作用下接近倒塌;经HDC条带加固的模型结构自振频率增大,位移反应相比未加固模型更小,山墙外闪现象得到明显控制,结构扭转效应的破坏作用明显减轻,在9度罕遇地震作用下HDC面层只出现轻微受损,可达到“大震可修”的性能目标。采用HDC条带加固法可有效延缓结构在强震作用下的刚度退化,增加结构的耐损伤能力,并有效提高此类砌体结构的整体抗震能力。

再生细骨料和砖粉双掺对3D打印混凝土性能的影响

为减少3D打印混凝土中天然骨料及胶凝材料的用量,本文采用再生混凝土细骨料替代部分天然细骨料,砖粉替代部分水泥,首先开展单掺再生细骨料(取代率为0、25%、50%、75%和100%)、单掺砖粉(取代率为0、5%、10%、15%、20%和30%)和两者双掺的现浇混凝土的流动性和抗压强度试验,以获得再生细骨料和砖粉的适宜取代率;然后探究50%再生细骨料和10%砖粉双掺及配合比调整方式(附加水、提高减水剂用量)对3D打印混凝土拌合物性能及硬化后力学性能的影响。试验结果表明,当再生细骨料的掺量不超过50%时,现浇混凝土抗压强度降低幅度在10%以内;随着砖粉掺量从0增加到30%,现浇混凝土抗压强度总体呈现先增后减、再稍有增加的趋势,当砖粉掺量为10%时,混凝土抗压强度最高;相比于单掺50%再生细骨料的混凝土,50%再生细骨料和10%砖粉双掺时混凝土强度有所增加,而流动性基本不变。对于3D打印混凝土,同时掺入50%再生细骨料和10%砖粉,并采用添加附加水的方式保持3D打印混凝土初始扩展度不变,会使得混凝土的可建造性提高,但坍落度、开放时间、抗压和劈裂抗拉强度降低,强度各向异性加剧;而提高减水剂用量不仅能显著提升3D打印混凝土的流动性能、开放时间和抗压强度,还能降低打印试件的强度各向异性。

砖混建筑垃圾制备蒸压加气混凝土性能及水化机理

以砖混建筑垃圾为主要原料制备蒸压加气混凝土(AAC),考察了废弃混凝土(WC)、废弃黏土砖(CB)及其复配掺量对蒸压加气混凝土抗压强度和干体积密度的影响,并利用X射线衍射(XRD)和扫描电子显微镜(SEM)分析了不同砖混配比加气混凝土样品的物相组成和微观形貌。结果表明,当建筑垃圾的掺量为50%~60%(质量分数,下同)时,以废弃混凝土或废弃黏土砖为原料制备的蒸压加气混凝土的抗压强度和干体积密度均能达到《蒸压加气混凝土砌块》(GB11968-2020)中A5.0 B07级别的要求。复配能进一步提升样品性能,随着废弃混凝土、废黏土砖质量比(m(WC)∶m(CB))的降低,所得样品的抗压强度不断升高,而干体积密度先降低后上升,当质量配比为2∶3~3∶2时,试样性能达到《蒸压加气混凝土砌块》(GB11968-2020)中A5.0 B06级别的要求。蒸压养护过程中,坯体中的SiO_(2)、Al_(2)O_(3)、Ca(OH)2、长石、富钙型水化硅酸钙(α-C_(2)SH)共同作用,生成大量片状托贝莫来石、半结晶的CSH(I)、CSH凝胶和少量水化石榴石、硬石膏,与原料中残留的石英、方解石一起填充在孔壁中,相互交织成网状,提高样品强度的同时降低其密度。砖混复配的样品含有更多结晶完整的托贝莫来石、CSH(I)以及适量的CSH凝胶,形成良好的网状致密结构,使样品综合性能更优。

废弃黏土砖骨料轻质混凝土正交试验研究

将废弃黏土砖骨料应用于轻质混凝土中,可实现建筑垃圾再利用,同步节省建筑材料,改善轻质混凝土性能。以废弃黏土砖颗粒为骨料,开展轻质混凝土制备试验,研究不同水灰比、泡沫掺量、纤维掺量对废弃黏土砖骨料轻质混凝土的物理力学性能影响。结果表明:水灰比对吸水率影响显著,随着水灰比的增大,吸水率增加了27.03%,泡沫掺量对干密度、抗压强度和劈裂抗拉强度影响显著,随泡沫掺量的增加,干密度、抗压强度和劈裂抗拉强度减小了17.78%、52.52%和34.83%,并建立了抗压强度与干密度、劈裂抗拉强度之间的对应关系式。

废黏土砖骨料轻质混凝土物理力学性能试验研究

将废弃黏土砖破碎成骨料用于制备轻质混凝土,可同步达到资源再利用、降低环境污染、节省天然骨料的目的。为揭示废弃黏土砖骨料轻质混凝土的性能,通过室内试验对废砖骨料级配、废砖骨料体积率、水灰比、泡沫掺量等因素影响轻质混凝土的干密度、吸水率、抗压强度性能进行试验研究,结果表明:泡沫掺量对干密度和抗压强度影响显著,泡沫掺量由2%增加到5%时,干密度由1407kg/m^(3)减小到1128kg/m^(3),抗压强度由13.39MPa减小到4.66MPa,废砖骨料级配对吸水率影响显著,骨料级配从A组到C组级配时,吸水率由11.3%减小到5.7%。

圆钢管砖骨料地聚物再生混凝土柱滞回性能试验研究

为探究废弃黏土砖再利用的可行性,对6根圆钢管砖骨料地聚物再生混凝土柱的滞回性能进行了系列试验研究。以不同钢管厚度(4、6 mm)、砖骨料取代率(0%、50%、100%)、轴压比(0.05、0.25、0.50)为参数,得到了试件在往复荷载作下的失效模态、骨架曲线和滞回曲线,并对构件的刚度退化、滞回性能、峰值承载力、延性、承载力退化和耗能能力等抗震性能指标的变化规律分析。结果表明:试件的失效模式表现为底部发生鼓曲、开裂,出现塑性铰的区域核心混凝土破碎,与普通钢管混凝土相似;砖骨料取代率和轴压比的增加会降低试件的承载力,钢管厚度的增加会提高试件的承载力。试件的滞回曲线饱满,表现出不明显的捏缩,表明耗能能力较好;轴压比的增加导致试件的变形能力降低,加快了刚度和承载力的退化速度,增长钢管厚度可以提高试件的变形能力;砖骨料取代率对试件刚度退化、延性、承载能力和耗能能力的影响有限。

UTILIZATION OF FLY ASH AND CONCRETE RESIDUE IN THE PRODUCTION OF GEOPOLYMER BRICKS

This study presents the development of geopolymer bricks synthetized from industrial waste,including fly ash mixed with concrete residue containing aluminosilicate compound.The above two ingredients are mixed according to five ratios:100:0,95:5,90:10,85:15,and 80:20.The mixture’s physico-mechanical properties,in terms of water absorption and the compressive strength of the geopolymer bricks,are investigated according to the TIS 168-2546 standard.Scanning electron microscopy(SEM)and X-ray diffraction(XRD)analyses are used to investigate the microstructure and the elemental and phase composition of the brick specimens.The results indicate that the combination of fly ash and concrete residue represents a suitable approach to brick production,as required by the TIS 168–2546 standard.

川南地区砖混结构房屋典型震害及地震易损性研究

以川南地区为研究区,并以在建造方式上具有明显当地地域特征的砖混结构房屋为研究对象,结合砖混结构房屋建造特点及川南历史地震(如长宁6.0级地震)震害调查结果等,分析砖混结构房屋典型震害特征,统计其在不同烈度下不同破坏等级的比例,采用经验分析法得到初步的易损性矩阵。在此基础上,针对因样本局限性造成的结构在高烈度下破坏比例不全,使实际易损性矩阵缺失的问题,通过插值法,推算高烈度下的破坏比例,补全经验易损性矩阵,拟合出易损性曲线,建立以震害统计为主、数值模拟为辅的砖混结构易损性分析模型;并基于平均震害指数对比分析,对易损性分析的可靠性进行检验。结果表明,构建的易损性矩阵能客观反映川南地区砖混结构房屋的抗震能力,对开展震害预测、灾害损失评估及震害风险评估等工作具有实际应用价值。

滑坡诱发农村山区砖混结构变形及演化规律研究

作为西南山区最为频发的地质灾害之一,滑坡对山区中大量存在的砖混房屋造成严重影响,尤其农村山区中受灾最为严重,给人民群众生产生活造成巨大安全隐患.研究滑坡引起的上部砖混结构变形特征,对科学指导房屋设计防护及灾后监测点布置具有重要现实意义.本文以酉阳高园子滑坡为例,通过现场调查和裂缝参数拟合研究了滑坡区砖混结构变形破坏特征.同时基于PFC3D,构建了有限体积-离散元(Finite Volume Method-Discrete Element Method,FVM-DEM)滑坡-房屋单向耦合模型,模拟并分析了在不同工况下滑坡动态发育过程,进一步揭示了房屋裂缝产生及演化过程.结果表明:相比于普通无柱砖混结构,底框结构抵抗滑坡诱发变形破坏的能力更强,并且处于前后缘段的房屋相对中段房屋更易出现损伤破坏;房屋的长宽比不宜过小,布置房屋长边走向平行斜坡走向有利于减少滑坡对房屋造成的破坏.本文总结了在滑坡作用下,上部砖混结构的变形特征和裂缝开展规律,可为农村山区砖混结构设计和布置提供参考.

方钢管砖混再生骨料混凝土短柱轴压性能有限元研究

目的 研究方钢管砖混再生骨料混凝土短柱的力学性能,推动建筑固废资源化利用。方法 利用ABAQUS软件建立方钢管砖混再生骨料混凝土短柱模型,将模拟结果与试验结果进行对比,验证了模型的正确性。然后分析砖混骨料取代率、倒角率、钢管屈服强度及厚度对短柱轴压力学性能的影响。结果 砖混骨料取代率小于50%时,极限承载力降低幅度在10%以内;当倒角率提高至0.16时,极限承载力有小幅度提升;试件的极限承载力随着钢管的厚度及屈服强度的增大而提高。结论 砖混骨料取代率较小时对试件承载能力影响较小,外包钢管的强度与厚度对试件承载能力有较大影响。对于方柱,适当提高倒角率可以使钢管更好约束混凝土,提高试件承载能力,但倒角率过大时截面面积有较大削弱,承载能力降低。

偏高岭土强化废弃砖粗骨料再生混凝土的性能研究

随着我国基建的大力发展,大量的老旧建筑因承载能力不足而被拆除,废弃材料也急剧增多,同时,天然灾害也是建筑物被破坏的重要因素,它会影响建筑材料的使用寿命。废砖占建筑垃圾很大部分,废弃砖的抗压、抗拉性能差,极易破碎被废弃。废弃砖骨料经过破碎、清洗、筛分后被用作再生粗骨料。为研究废弃砖骨料替代率、偏高岭土替代水泥的量、废弃砖再生混凝土的力学及耐久性能,通过SEM电镜等方式,对废弃砖再生骨料混凝土的微观结构进行研究,根据试验发现废弃粘土砖替代率为30%,偏高岭土的掺量为6%时抗压强度最高,再生混凝土的抗氯离子性能较好。