Durability design of recycled high performance concrete（RHPC） is fundamental for improving the use rate and level of concrete waste as coarse recycled aggregate（CRA）. We discussed a frostdurability-based mix propo...Durability design of recycled high performance concrete（RHPC） is fundamental for improving the use rate and level of concrete waste as coarse recycled aggregate（CRA）. We discussed a frostdurability-based mix proportion design method for RHPC using 100 % CRA and natural sand. Five groups of RHPC mixes with five strength grades（40, 50, 60, 70 and 80 MPa） were produced using CRA with four quality classes, and their workability, 28 d compressive strengths and frost resistances（measured by the compressive strength loss ratio and the relative dynamic modulus of elasticity） were tested. Relationships between the 28 d compressive strength, the frost resistance and the CRA quality characteristic parameter, water absorption, were then developed. The criterion of a CRA maximum water absorption limit value for RHPC was suggested, independent of its source and quality class. The results show that all RHPC mixes achieve the expected target workability, strength, and frost durability. The research results demonstrate that the application of the proposed method does not require trial testing prior to use.展开更多
In recent years, the rationalization of concrete mix ratios which batches equal volumes of sand and gravel in building projects has been gaining grounds in the Cameroon construction industry. The main objective of thi...In recent years, the rationalization of concrete mix ratios which batches equal volumes of sand and gravel in building projects has been gaining grounds in the Cameroon construction industry. The main objective of this study is therefore to investigate if the concrete produced with rationalized mix ratio can be adopted as conventional mix ratio in terms of minimum required compression strength of concrete for buildings. Specifically this work compared the conventional mix ratio of 350 kg of cement: 400 liters of sand: 800 liters of gravel for a cubic meter and the rationalized batch of 350 kg of cement: 600 liters of sand: 600 liters of 5/15 gravel, 15/25 gravel and a combination of 5/15 + 15/25 gravel. Average compressive tests’results for both the conventional and the rationalized mix ratios were found to meet the minimum compressive strength of 65% at 7 days, 90% at 14 days and 99% at 28 days for gravel size combination 5/15 + 15/25. Single size gravel of 5/15 and 15/25 did not meet the minimum required compressive strength of 20 N/mm<sup>2</sup> for the rationalized mix ratio at 28 days curing based on the minimum compressive strength required, this study arrives at the conclusion that the equal volumes of sand and gravel mix ratio of 350 kg/m<sup>3</sup> of cement: 600 liters of sand: 600 liters of gravel mix ratio can be adopted as a conventional concrete mix ratio for gravel size 5/15 + 15/25.展开更多
Common ways of disposing waste plastic such as incineration and landfilling have negative impacts on the environment. Partial replacement of natural aggregate in concrete with waste plastic including polyethylene tere...Common ways of disposing waste plastic such as incineration and landfilling have negative impacts on the environment. Partial replacement of natural aggregate in concrete with waste plastic including polyethylene terephthalate (PET) is more environmental friendly and sustainable. The effect of adding 5% to 20% waste plastic by volume of natural coarse aggregate (“gravel”) and plastic particle size (3 to 7 mm) on the density and compressive strength of plastic-concrete mix after 28 days of curing was studied. The results showed that density of the concrete decreased from 2406.7 to 2286.7 kg/m3 as waste plastic increased from 5% to 20% v/v compared with 2443.3 kg/m3 recorded by concrete without waste plastic. Change in particle size from 3 to 7 mm has no significant effect on the density of the plastic-concrete mix. The compressive strength decreased as the volume and particle size of waste plastic increased. When waste plastic volume changed from 5% to 20% v/v, the compressive strength decreased from 20.5 to 15 MPa, 18.6 to 14.3 MPa and 17.2 to 13.8 MPa for 3, 5 and 7 mm waste plastic particle size respectively while the concrete without plastic has 21.33 MPa. Therefore, the addition of 5% (v/v gravel) of flaky waste plastic in the concrete produces a lightweight concrete which could offer economic benefit without substantially reducing the compressive strength of the plastic-concrete mix.展开更多
This paper presents the results of a series of studies on the influence of curing conditions on the strength development of high strength concrete. The 1-, 3-, 7-, 14- and 28-day strengths of four different mixes of G...This paper presents the results of a series of studies on the influence of curing conditions on the strength development of high strength concrete. The 1-, 3-, 7-, 14- and 28-day strengths of four different mixes of Grade 75 similar to 80 concrete, with or without pulverized fuel ash and/or condensed silica fume, under five different curing regimes were investigated. It is revealed that the curing conditions have significant influence on both the short term and long term strength development of the concrete and that concrete mixes of the same grade but containing different mineral admixtures show distinct favour for a curing regime. These results will be helpful for evaluating suitable curing methods for high strength concrete with different mix proportions.展开更多
Concrete properties such as unit weight and compressive strength are highly dependable on the properties of aggregate. Current research aims to study the effect of aggregate properties on concrete considering the reso...Concrete properties such as unit weight and compressive strength are highly dependable on the properties of aggregate. Current research aims to study the effect of aggregate properties on concrete considering the resource of aggregate. The properties of aggregate and fine sand were studied (specific gravity, density, absorption, and abrasion). Also, the properties of concrete were studied (density, unit weight, and compressive strength). Samples of coarse and medium aggregates, and fine sand were collected from different areas in Jordan (Ajloun, Amman, Aqaba, Irbid, Jerash, Karak, Ma’an, Madaba, Salt, Zarqa, and Tafila) to be tested and used in concrete mix. Aggregate from South of Jordan has higher values in specific gravity and bulk density (Aqaba, Ma’an, and Karak aggregates). Also, the same aggregate samples have lower values in absorption and abrasion (Ma’an, Aqaba, Karak, and Tafila). For the properties of concrete that include density, unit weight, and compressive strength, all samples have achieved the design properties and strength in the current study. For density and unit weight, samples from South of Jordan have higher values (Ma’an and Aqaba). And for compressive strength, Ma’an, Irbid and Amman concrete samples have the highest values at 7-day, while the 28-day compressive strength comes highest for Zarqa, Ma’an, Irbid and Amman. From the results of the current study, the compressive strength at 7-day and 28-day is related to the density of coarse and medium aggregate, abrasion, and absorption. The higher the density, the higher the compressive strength. And the lower abrasion and absorption, the higher the compressive strength of concrete. Current research will be useful in selecting the source of aggregate to produce a considerable concrete strength.展开更多
A recycled aggregate(RA)was prepared by crushing and sieving demolished discarded concrete pavements and was subsequently tested and analyzed to determine its various physical properties.On this basis,pervious concre...A recycled aggregate(RA)was prepared by crushing and sieving demolished discarded concrete pavements and was subsequently tested and analyzed to determine its various physical properties.On this basis,pervious concrete(PC)mix proportions were designed.Coarse RA particles with sizes of 5–10 and 10–20 mm were selected.Concrete specimens were prepared with a water–cement ratio of 0.3,an aggregate–cement ratio of 4.5,the substitute rates of RA with 0,25%,50%,75%and a single-/double-gap-graded RA mix(mass ratio of particles with sizes of 5–10 mm to particles with sizes of 10–20 mm:1:1,1:2,2:1,2:3 and 3:2).Various properties of the RA-containing PC(RPC)were determined by analyzing the compressive strength,splitting tensile strength,effective porosity,permeation coefficient and impact and abrasion resistance of the specimens.The results showed the following:The density of the RPC decreased with an increasing RA replacement ratio.The density of the RPC prepared with a double-gapgraded RA mix was lower than that prepared with a single-gap-graded RA(particle size:10–20 mm)mix.The permeation coefficient of the RPC increased with increasing porosity.The splitting tensile strength of the RPC was positively correlated with its compressive strength.The compressive strength of the RPC decreased with increasing porosity.The regression analysis showed that the impact and abrasion resistance of the RPC increased with increasing compressive strength.In addition,all of the RPC specimens met the strength and permeation requirements.This study can provide theoretical support for the application of RPC.展开更多
The effect of carbonation treatment and mixing method on the mechanical properties and interfacial transition zone（ITZ） properties of recycled aggregate concrete（RAC） was investigated. Properties of recycled concr...The effect of carbonation treatment and mixing method on the mechanical properties and interfacial transition zone（ITZ） properties of recycled aggregate concrete（RAC） was investigated. Properties of recycled concrete aggregate（RCA） were tested firstly. Then, five types of concretes were made and slump of fresh concrete was measured immediately after mixing. Compressive strength and splitting tensile strength of hardened concrete were measured at 28 d. Meanwhile, the microstructure of RAC was analyzed by backscattered electron（BSE） image. It was found that the water absorption ratio of carbonated recycled concrete aggregate（CRCA） was much lower when compared to the untreated RCA. Comparatively, the apparent density of CRCA was not significantly modified. The concrete strength results indicate that the mix CRAC-2 prepared with CRCA by adopting two-stage mixing approach shows the highest compressive strength value compared to the other mixes. The microstructural analysis demonstrate that the mix CRAC-2 has a much denser old ITZ than the untreated RAC because of the chemical reaction between CO2 and the hydration products of RCA. This study confirms that the ITZ microstructure of RAC can be efficiently modified by carbonation treatment of RCA and encourages broadening the application of construction and demolition wastes.展开更多
With the resource shortage in coastal areas,the construction of concrete structures using freshwater and river sand has brought great economic and environmental costs.The use of seawater,sea sand,and coral aggregates ...With the resource shortage in coastal areas,the construction of concrete structures using freshwater and river sand has brought great economic and environmental costs.The use of seawater,sea sand,and coral aggregates in concrete mixes has become an alternative solution for coastal and marine structures,especially for offshore structures and artificial islands.In this study,378 seawater,sea sand,and coral aggregate concrete(Coral-SWSSC)specimens were prepared,and their mechanical properties were investigated comprehensively through compressive tests to explore the optimized mix design at different grades.Results showed that the mechanical properties of Coral-SWSSC were strongly correlated with the water-to-binder ratios,coastal particle gradings,and pretreatment method of coastal particles.Based on the experimental results,mix proportion designs of CoralSWSSC were proposed for concrete from C20 to C50 grades,and the failure mechanism of Coral-SWSSC at different grades was discussed according to their respective failure modes.The findings of the current study provide knowledge on the optimized design of Coral-SWSSC,which can be used to promote the application of Coral-SWSSC in offshore,marine,and ocean engineering.展开更多
The present study proposes the mix design method of Fly Ash(FA)based geopolymer concrete using Response Surface Methodology(RSM).In this method,different factors,including binder content,alkali/binder ratio,NS/NH rati...The present study proposes the mix design method of Fly Ash(FA)based geopolymer concrete using Response Surface Methodology(RSM).In this method,different factors,including binder content,alkali/binder ratio,NS/NH ratio(sodium silicate/sodium hydroxide),NH molarity,and water/solids ratio were considered for the mix design of geopolymer concrete.The 2D contour plots were used to setup the mix design method to achieve the target compressive strength.The proposed mix design method of geopolymer concrete is divided into three categories based on curing regime,specifically one ambient curing(25°C)and two heat curing(60 and 90°C).The proposed mix design method of geopolymer concrete was validated through experimentation of M30,M50,and M70 concrete mixes at all curing regimes.The observed experimental compressive strength results validate the mix design method by more than 90%of their target strength.Furthermore,the current study concluded that the required compressive strength can be achieved by varying any factor in the mix design.In addition,the factor analysis revealed that the NS/NH ratio significantly affects the compressive strength of geopolymer concrete.展开更多
基金Funded by the National Natural Science Foundation of China(No.51278073)Prospective Joint Research Project of Jiangsu Province(No.BY2015027-23)State Key Laboratory for Geo Mechanics and Deep Underground Engineering,China University of Mining&Technology(No.SKLGDUEK1704)
文摘Durability design of recycled high performance concrete（RHPC） is fundamental for improving the use rate and level of concrete waste as coarse recycled aggregate（CRA）. We discussed a frostdurability-based mix proportion design method for RHPC using 100 % CRA and natural sand. Five groups of RHPC mixes with five strength grades（40, 50, 60, 70 and 80 MPa） were produced using CRA with four quality classes, and their workability, 28 d compressive strengths and frost resistances（measured by the compressive strength loss ratio and the relative dynamic modulus of elasticity） were tested. Relationships between the 28 d compressive strength, the frost resistance and the CRA quality characteristic parameter, water absorption, were then developed. The criterion of a CRA maximum water absorption limit value for RHPC was suggested, independent of its source and quality class. The results show that all RHPC mixes achieve the expected target workability, strength, and frost durability. The research results demonstrate that the application of the proposed method does not require trial testing prior to use.
文摘In recent years, the rationalization of concrete mix ratios which batches equal volumes of sand and gravel in building projects has been gaining grounds in the Cameroon construction industry. The main objective of this study is therefore to investigate if the concrete produced with rationalized mix ratio can be adopted as conventional mix ratio in terms of minimum required compression strength of concrete for buildings. Specifically this work compared the conventional mix ratio of 350 kg of cement: 400 liters of sand: 800 liters of gravel for a cubic meter and the rationalized batch of 350 kg of cement: 600 liters of sand: 600 liters of 5/15 gravel, 15/25 gravel and a combination of 5/15 + 15/25 gravel. Average compressive tests’results for both the conventional and the rationalized mix ratios were found to meet the minimum compressive strength of 65% at 7 days, 90% at 14 days and 99% at 28 days for gravel size combination 5/15 + 15/25. Single size gravel of 5/15 and 15/25 did not meet the minimum required compressive strength of 20 N/mm<sup>2</sup> for the rationalized mix ratio at 28 days curing based on the minimum compressive strength required, this study arrives at the conclusion that the equal volumes of sand and gravel mix ratio of 350 kg/m<sup>3</sup> of cement: 600 liters of sand: 600 liters of gravel mix ratio can be adopted as a conventional concrete mix ratio for gravel size 5/15 + 15/25.
文摘Common ways of disposing waste plastic such as incineration and landfilling have negative impacts on the environment. Partial replacement of natural aggregate in concrete with waste plastic including polyethylene terephthalate (PET) is more environmental friendly and sustainable. The effect of adding 5% to 20% waste plastic by volume of natural coarse aggregate (“gravel”) and plastic particle size (3 to 7 mm) on the density and compressive strength of plastic-concrete mix after 28 days of curing was studied. The results showed that density of the concrete decreased from 2406.7 to 2286.7 kg/m3 as waste plastic increased from 5% to 20% v/v compared with 2443.3 kg/m3 recorded by concrete without waste plastic. Change in particle size from 3 to 7 mm has no significant effect on the density of the plastic-concrete mix. The compressive strength decreased as the volume and particle size of waste plastic increased. When waste plastic volume changed from 5% to 20% v/v, the compressive strength decreased from 20.5 to 15 MPa, 18.6 to 14.3 MPa and 17.2 to 13.8 MPa for 3, 5 and 7 mm waste plastic particle size respectively while the concrete without plastic has 21.33 MPa. Therefore, the addition of 5% (v/v gravel) of flaky waste plastic in the concrete produces a lightweight concrete which could offer economic benefit without substantially reducing the compressive strength of the plastic-concrete mix.
文摘This paper presents the results of a series of studies on the influence of curing conditions on the strength development of high strength concrete. The 1-, 3-, 7-, 14- and 28-day strengths of four different mixes of Grade 75 similar to 80 concrete, with or without pulverized fuel ash and/or condensed silica fume, under five different curing regimes were investigated. It is revealed that the curing conditions have significant influence on both the short term and long term strength development of the concrete and that concrete mixes of the same grade but containing different mineral admixtures show distinct favour for a curing regime. These results will be helpful for evaluating suitable curing methods for high strength concrete with different mix proportions.
文摘Concrete properties such as unit weight and compressive strength are highly dependable on the properties of aggregate. Current research aims to study the effect of aggregate properties on concrete considering the resource of aggregate. The properties of aggregate and fine sand were studied (specific gravity, density, absorption, and abrasion). Also, the properties of concrete were studied (density, unit weight, and compressive strength). Samples of coarse and medium aggregates, and fine sand were collected from different areas in Jordan (Ajloun, Amman, Aqaba, Irbid, Jerash, Karak, Ma’an, Madaba, Salt, Zarqa, and Tafila) to be tested and used in concrete mix. Aggregate from South of Jordan has higher values in specific gravity and bulk density (Aqaba, Ma’an, and Karak aggregates). Also, the same aggregate samples have lower values in absorption and abrasion (Ma’an, Aqaba, Karak, and Tafila). For the properties of concrete that include density, unit weight, and compressive strength, all samples have achieved the design properties and strength in the current study. For density and unit weight, samples from South of Jordan have higher values (Ma’an and Aqaba). And for compressive strength, Ma’an, Irbid and Amman concrete samples have the highest values at 7-day, while the 28-day compressive strength comes highest for Zarqa, Ma’an, Irbid and Amman. From the results of the current study, the compressive strength at 7-day and 28-day is related to the density of coarse and medium aggregate, abrasion, and absorption. The higher the density, the higher the compressive strength. And the lower abrasion and absorption, the higher the compressive strength of concrete. Current research will be useful in selecting the source of aggregate to produce a considerable concrete strength.
基金This study was funded by the National key research and development program fund project(No.2018YFC0406803).
文摘A recycled aggregate(RA)was prepared by crushing and sieving demolished discarded concrete pavements and was subsequently tested and analyzed to determine its various physical properties.On this basis,pervious concrete(PC)mix proportions were designed.Coarse RA particles with sizes of 5–10 and 10–20 mm were selected.Concrete specimens were prepared with a water–cement ratio of 0.3,an aggregate–cement ratio of 4.5,the substitute rates of RA with 0,25%,50%,75%and a single-/double-gap-graded RA mix(mass ratio of particles with sizes of 5–10 mm to particles with sizes of 10–20 mm:1:1,1:2,2:1,2:3 and 3:2).Various properties of the RA-containing PC(RPC)were determined by analyzing the compressive strength,splitting tensile strength,effective porosity,permeation coefficient and impact and abrasion resistance of the specimens.The results showed the following:The density of the RPC decreased with an increasing RA replacement ratio.The density of the RPC prepared with a double-gapgraded RA mix was lower than that prepared with a single-gap-graded RA(particle size:10–20 mm)mix.The permeation coefficient of the RPC increased with increasing porosity.The splitting tensile strength of the RPC was positively correlated with its compressive strength.The compressive strength of the RPC decreased with increasing porosity.The regression analysis showed that the impact and abrasion resistance of the RPC increased with increasing compressive strength.In addition,all of the RPC specimens met the strength and permeation requirements.This study can provide theoretical support for the application of RPC.
基金Funded by the National Natural Science Foundation of China(Nos.51278073,51678081,51678143)State Key Laboratory for Geo-mechanics and Deep Underground Engineering,China University of Mining&Technology(No.SKLGDUEK1704)
文摘The effect of carbonation treatment and mixing method on the mechanical properties and interfacial transition zone（ITZ） properties of recycled aggregate concrete（RAC） was investigated. Properties of recycled concrete aggregate（RCA） were tested firstly. Then, five types of concretes were made and slump of fresh concrete was measured immediately after mixing. Compressive strength and splitting tensile strength of hardened concrete were measured at 28 d. Meanwhile, the microstructure of RAC was analyzed by backscattered electron（BSE） image. It was found that the water absorption ratio of carbonated recycled concrete aggregate（CRCA） was much lower when compared to the untreated RCA. Comparatively, the apparent density of CRCA was not significantly modified. The concrete strength results indicate that the mix CRAC-2 prepared with CRCA by adopting two-stage mixing approach shows the highest compressive strength value compared to the other mixes. The microstructural analysis demonstrate that the mix CRAC-2 has a much denser old ITZ than the untreated RAC because of the chemical reaction between CO2 and the hydration products of RCA. This study confirms that the ITZ microstructure of RAC can be efficiently modified by carbonation treatment of RCA and encourages broadening the application of construction and demolition wastes.
基金supported by the National Natural Science Foundation of China (Grant Nos.52078310,51878420)the Ministry of Science and Technology of China (Grant Nos.2018YFC1504303,2017YFC1503103)Xingliao Talent Program of Liaoning Province (Grant No.XLYC1902038)。
文摘With the resource shortage in coastal areas,the construction of concrete structures using freshwater and river sand has brought great economic and environmental costs.The use of seawater,sea sand,and coral aggregates in concrete mixes has become an alternative solution for coastal and marine structures,especially for offshore structures and artificial islands.In this study,378 seawater,sea sand,and coral aggregate concrete(Coral-SWSSC)specimens were prepared,and their mechanical properties were investigated comprehensively through compressive tests to explore the optimized mix design at different grades.Results showed that the mechanical properties of Coral-SWSSC were strongly correlated with the water-to-binder ratios,coastal particle gradings,and pretreatment method of coastal particles.Based on the experimental results,mix proportion designs of CoralSWSSC were proposed for concrete from C20 to C50 grades,and the failure mechanism of Coral-SWSSC at different grades was discussed according to their respective failure modes.The findings of the current study provide knowledge on the optimized design of Coral-SWSSC,which can be used to promote the application of Coral-SWSSC in offshore,marine,and ocean engineering.
文摘The present study proposes the mix design method of Fly Ash(FA)based geopolymer concrete using Response Surface Methodology(RSM).In this method,different factors,including binder content,alkali/binder ratio,NS/NH ratio(sodium silicate/sodium hydroxide),NH molarity,and water/solids ratio were considered for the mix design of geopolymer concrete.The 2D contour plots were used to setup the mix design method to achieve the target compressive strength.The proposed mix design method of geopolymer concrete is divided into three categories based on curing regime,specifically one ambient curing(25°C)and two heat curing(60 and 90°C).The proposed mix design method of geopolymer concrete was validated through experimentation of M30,M50,and M70 concrete mixes at all curing regimes.The observed experimental compressive strength results validate the mix design method by more than 90%of their target strength.Furthermore,the current study concluded that the required compressive strength can be achieved by varying any factor in the mix design.In addition,the factor analysis revealed that the NS/NH ratio significantly affects the compressive strength of geopolymer concrete.
