Conduction Properties and Scattering Mechanisms in F-doped Textured Transparent Conducting SnO_2 Films Deposited by APCVD

Transparent conducting F-doped texture SnO2 films with resistivity as low as 5× 10-4 Ω ·cm,with carrier concentrations between 3.5 × 1020 and 7× 1020 cm-3 and Hall mobilities from 15.7 to 20.1 cm2/(V/s) have been prepared by atmosphere pressure chemical vapour deposition (APCVD). These polycrystalline films possess a variable preferred orientation, the polycrystallite sizes and orientations vary with substrate temperature. The substrate temperature and fluorine flow rate dependence of conductivity, Hall mobility and carrier conentration fOr the resultingfilms have been obtained. The temperature dependence of the mobiity and carrier concentrationhave been measured over a temperature range 16～400 K. A systematically theoretical analysis on scattering mechanisms for the highly conductive SnO2 films has been given. Both theoretical analysis and experimental results indicate that for these degenerate, polycrystalline SnO2 ：F films in the low temperature range (below 100 K), ionized impurity scattering is main scattering mechanism. However, when the temperature is higher than 100 K, the lattice vibration scattering becomes dominant. The grain boundary scattering makes a small contribution to limit the mobility of the films.

Crystallization and Conductivity Mechanism of ITO Films on Different Substrates Deposited with Different Substrate Temperatures

ITO thin films were grown on PC（polycarbonate）, PMMA（polymethyl methacrylate） and glass substrates by r.f. magnetron sputtering. The electrical, structural and chemical characteristics of ITO films were analyzed by the Hall Technique, X-ray diffraction, and X-ray photoelectron spectroscopy. XPS studies suggest that all the ITO films consist of crystalline and amorphous phases. The degree of crystallinity increases from less than 45% to more than 90% when the substrate temperature increases from 80 to 300 ℃. The In and Sn exist in the chemical state of In^3＋ and Sn^4＋, respectively, independent of substrate type and temperature. The enrichment of Sn on surface and In in body of ITO films are also revealed. And, the oxygen deficient regions exist both in surface layer and film body. For ITO films deposited under 180 ℃ , the carrier concentration are mainly provided by oxygen vacancies, and the dominant electron carrier scattering mechanism is grain boundary scattering between the crystal and the amorphous grain. For ITO films deposited over 180 ℃, the carrier concentration are provided by tin doping, and the dominant scattering mechanism transforms from grain boundary scattering between the crystal grains to ionized impurity scattering with increasing deposition temperature.

The conductive mechanisms of a titanium oxide memristor with dopant drift and a tunnel barrier

Nano-scale titanium oxide memristors exhibit complex conductive characteristics, which have already been proved by existing research. One possible reason for this is that more than one mechanism exists, and together they codetermine the conductive behaviors of the memristor. In this paper, we first analyze the theoretical base and conductive process of a memristor, and then propose a compatible circuit model to discuss and simulate the coexistence of the dopant drift and tunnel barrier-based mechanisms. Simulation results are given and compared with the published experimental data to prove the possibility of the coexistence. This work provides a practical model and some suggestions for studying the conductive mechanisms of memristors.

INVESTIGATION OF MICROSTRUCTURE AND CONDUCTIVE MECHANISM OF HIGH DENSITY POLYETHYLENE/CARBON BLACK PARTICLE COMPOSITE BY POSITRON ANNIHILATION LIFETIME SPECTROSCOPY

The microstructure and conductive mechanism of high density polyethylene/carbon black (HDPE/CB) composite were investigated by positron annihilation lifetime spectroscopy (PALS). The PALS were measured in two series of samples, one with various CB contents in the composites and the other with various gamma-irradiation doses in HDPE/CB composite containing 20 wt% CB. It was found that CB particles distribute in the amorphous regions, the CB critical content value in HDPE/CB composite is about 16.7 wt% and the suitable gamma-irradiation dose for improving the conductive behavior of HDPE/CB composite is about 20 Mrad. The result observed for the second set of samples suggests that gamma-irradiation causes not only cross-linking in amorphous regions but also destruction of the partial crystalline structure. Therefore, a suitable irradiation dose, about 20 Mrad, can induce sufficient cross-linking in the amorphous regions without enhancing the decomposition of crystalline structure, so that the positive temperature coefficient (PTC) effect remains while the negative temperature coefficient (NTC) effect is suppressed. A new interpretation of the conductive mechanism, which might provide a more detailed explanation of the PTC effect and the NTC effect has been proposed.

STUDY ON THE STRUCTURE, ELECTRICAL PROPERTIES AND CONDUCTION MECHANISM 0F THE MULTICRYSTAL MULTIPHASE MATERIAL Li_2MO_2-xWxO_6

The conductivity of non-crystalline fast ionic conductor for B_2O_3-Li_2O-LiCl-Al_2O_3 system is studiedin this paper. The glass structure of this system is discussed by means of infrared spectrum and X-ray fluorescence analysis, and the effects of LiCl and A1_2O_3 on the conductivity of Li^+ in the system are studied as well. Adding Li_2O to the system gives rise to transfer from [BO_3] triangular units to [BO_4] tetrahedral. When Li_2O content exceeds 30mol%, the main group of the glass is the diborate group with more [BO_4] tetrahedra. The adding of LiCl has no obvious influence on the glass structure, and LiCl is under a state dissociated by network, but with the increase of LiCl, the increase of conductivity is obvious. By adding A1_2O_3, the glass can be formed when the room-temperature is cooling down,the conductivity decreases while the conductive activatory energy increases for the glass. The experiment shows that conductivity in the room-temperature is σ= 6.2×10^(-6)Ω^(-1)cm^(-1), when at 300℃, the σ=6.8×10^(-3)Ω^(-1)cm^(-1). The conductive activatory energy computed is 0.6～1.0eV.

IONIC CONDUCTION MECHANISM IN Na_(5+x)YA1_xSi_(4-x)O_(12) SUPERIONIC CONDUCTORS

Na_(5+x) YAl_x Si_(4-x) O_(12) polycrystalline solid electrolytes are prepared by solid reactions. By the analyses of X-ray, TG and DTA, infrared spectu re, and SEM, the variasion of their density with the composition X are discussed Their electric conductivity in the temperature range of R. T. to 300℃ are determined with electric brigde, and their variasions with the compositions X and temperature are studied. Their activations in the tem- perature range 140℃ to 300℃ are calculated, and their variation with the compositons X are discussed.

Performance of High Thermal Conductivity Dense Silica Bricks and Their High Thermal Conductivity Mechanism

High thermal conductivity dense silica bricks have the higher thermal conductivity than ordinary silica bricks,which is conducive to the realization of energy saving and emission reduction in the iron and steel industry.The performance of ordinary silica bricks and high thermal conductivity dense silica bricks was compared,and the high thermal conductivity mechanism was analyzed.The results show that(1)compared with ordinary silica bricks,high thermal conductivity dense silica bricks have the characteristics of higher thermal conductivity,lower apparent porosity,higher tridymite content,higher compressive strength,and higher thermal expansion;(2)by increasing the tridymite content and reducing the porosity,the close packing of honeycombα-tridymite improves the density and continuity of the SiO_(2)frame structure of the silica bricks,and the larger area perpendicular to the heat transfer direction improves the thermal conductivity of the bricks;(3)the densification of the silica bricks also increases the thermal expansion of the bricks,but they still meet the standard requirements.

Influence of anisotropy on the electrical conductivity and diffusion coefficient of dry K-feldspar： Implications of the mechanism of conduction

The electrical conductivities of single-crystal K-feldspar along three different crystallographic directions are investigated by the Solartron-1260 Impedance/Gain-phase analyzer at 873 K–1223 K and 1.0 GPa–3.0 GPa in a frequency range of 10-1 Hz–106 Hz. The measured electrical conductivity along the ⊥ [001] axis direction decreases with increasing pressure, and the activation energy and activation volume of charge carriers are determined to be 1.04 ± 0.06 e V and 2.51 ± 0.19 cm~3/mole, respectively. The electrical conductivity of K-feldspar is highly anisotropic, and its value along the⊥ [001] axis is approximately three times higher than that along the ⊥ [100] axis. At 2.0 GPa, the diffusion coefficient of ionic potassium is obtained from the electrical conductivity data using the Nernst–Einstein equation. The measured electrical conductivity and calculated diffusion coefficient of potassium suggest that the main conduction mechanism is of ionic conduction, therefore the dominant charge carrier is transferred between normal lattice potassium positions and adjacent interstitial sites along the thermally activated electric field.

Efficient proton conduction in porous and crystalline covalent-organic frameworks(COFs)

To attain the objectives of carbon peaking and carbon neutrality,the development of stable and highperformance ion-conducting materials holds enormous relevance in various energy storage and conversion devices.Particularly,crystalline porous materials possessing built-in ordered nanochannels exhibit remarkable superiority in comprehending the ion transfer mechanisms with precision.In this regard,covalent organic frameworks(COFs)are highly regarded as a promising alternative due to their preeminent structural tunability,accessible well-defined pores,and excellent thermal/chemical stability under hydrous/anhydrous conditions.By the availability of organic units and the diversity of topologies and connections,advances in COFs have been increasing rapidly over the last decade and they have emerged as a new field of proton-conducting materials.Therefore,a comprehensive summary and discussion are urgently needed to provide an"at a glance"understanding of the prospects and challenges in the development of proton-conducting COFs.In this review,we target a comprehensive review of COFs in the field of proton conductivity from the aspects of design strategies,the proton conducting mechanism/features,the relationships of structure-function,and the application of research.The relevant content of theoretical simulation,advanced structural characterizations,prospects,and challenges are also presented elaborately and critically.More importantly,we sincerely hope that this progress report will form a consistent view of this field and provide inspiration for future research.

Conductive metal-organic frameworks: Recent advances in electrochemical energy-related applications and perspectives

Metal-organic frameworks(MOFs),typically constructed with metallic nodes and organic linkers,have influenced the development of modular solid materials.Their adjustable molecular structure provides a remarkable variety of MOF-based solid-state structures towards diverse applications.However,the low conductivity of traditional MOFs extremely hinders their applications in electronic and electrochemical devices.The emerging conductive MOFs,generally possessing twodimensional layered structures,are endowed with both the structural merits of common MOFs and exceptional electronic/ionic conductivities.Besides,the selection and optimization of ligands and metal centers,as well as synthetic methods enormously affects the intrinsic conductivity of conductive MOFs.The distinctive crystal structures and superb conductivity promise their appealing applications in electrochemical energy-related fields.In the review,we mainly summarize representative crystal features,conducting mechanisms and recent advances in rational design and synthesis of conductive MOFs,along with their versatile applications as electrodes for electrochemical capacitors and rechargeable batteries,and as catalysts towards electrocatalysis.Finally,the involved challenges and future trends/prospects of the conductive MOFs for electrochemical energyrelated applications are further proposed.

Breaking Through Bottlenecks for Thermally Conductive Polymer Composites:A Perspective for Intrinsic Thermal Conductivity,Interfacial Thermal Resistance and Theoretics

Rapid development of energy,electrical and electronic technologies has put forward higher requirements for the thermal conductivities of polymers and their composites.However,the thermal conductivity coefficient(λ)values of prepared thermally conductive polymer composites are still difficult to achieve expectations,which has become the bottleneck in the fields of thermally conductive polymer composites.Aimed at that,based on the accumulation of the previous research works by related researchers and our research group,this paper proposes three possible directions for breaking through the bottlenecks:(1)preparing and synthesizing intrinsically thermally conductive polymers,(2)reducing the interfacial thermal resistance in thermally conductive polymer composites,and(3)establishing suitable thermal conduction models and studying inner thermal conduction mechanism to guide experimental optimization.Also,the future development trends of the three above-mentioned directions are foreseen,hoping to provide certain basis and guidance for the preparation,researches and development of thermally conductive polymers and their composites.

Fabrication and Microstructure of BN Matrix Composites with Electrical Conductivity

BN ceramic is an advanced engineering ceramics with excellent thermal shock resistance, good workability and excellent dielectricity.TiB 2 ceramic has excellent electric conductivity,high melting points, and corrosion resistance to molten metal.Therefore,the composite consisting of BN and TiB 2 ceramics is expected to have a combination of above mentioned properties,thereby can be used as self heating crucible.In this paper,hot pressing technology was used to fabricate the high performance BN TiB 2 composite materials.microstructure and electric conducting mechanism were studied,and the relationship between the microstructure and physical property was discussed.The results show that the microstructure of composites has a great influence on the physical property of composites.The BN TiB 2 composites with excellent mechanical strength and stable resistivity can be obtained by optimizing the processing parameter and controlling the microstructure of composites.

Fluoride solid electrolytes containing rare earth elements

Relations between the structure, ionic conductivity and dielectric properties of fluoride systems of different structures containing rare earth elements were presented. Superionic conductivities, by fluoride ions, of fluorite-structured （MF2-REF3, M=Ba, Pb, RE=La-Lu, Sc, Y）, orthorhombic （REF3, RE=Tb-Er, Y）, tysonite-structured （REF3-MF2, RE=La-Nd, M=Sr）, monoclinic （BaRE2Fs, RE=Ho-Yb, Y） fluoride single crystals and eutectic composites （LiF-REF3, RE=La-Gd, Y） were compared. Anisotropy of electrical properties of crystals with a lower symmetry was explained by modeling optimum ionic paths. For explanation of concentration dependences of fast ionic conductivity, models of aggregation of defects into clusters were proposed. In fluorite-structured crystals, the highest ionic conductivity was found for PbF2：7 mol% ScF3 （at 500 K, σ500=0.13 S/cm）. In tysonite-structured crystals, the highest ionic conductivity was found for LaF3：3 mol% SrF2 （σ500=2.4×10^-2 S/cm）. Different types of coordination polyhedrons and their different linking in orthorhombic and tysonite structure explained large differences between conductivities in both structures. Eutectic systems, prepared as directionally solidified composites, enabled to study some orthorhombic fluoride phases （GdF3, SmF3）, which cannot be prepared as single crystals. An influence of the orthorhombic-tysonite phase transition on the ionic conductivity was shown.

Electrical Relaxation in Mixed Alkali Bi_2O_3-K_2O-Li_2O-Fe_2O_3 Glasses

A new glass system （Bi2O3）50（Fe2O3）10（Li2O）x（K2O）40-x, where x changes in steps of 5 mole fraction between 0 and 40, was selected to study the electrical relaxation and the mixed alkali effect （MAE） phenomena. Measurements of ac conductivity σac, dielectric permittivity ε′ and loss factor tanδ in the frequency range of 0.12～10^2 kHz and in the temperature range of 300～650 K were carried out. The temperature dependence of the ac conductivity shows a slow increasing rate at low temperature and high frequency and a rapid increase at high temperature and low frequency. At constant temperature, the ac conductivity is found to be proportional to ω^8, where s is the frequency exponent, which is less than 1. Analysis of the conductivity data and the frequency exponent shows that the overlapping large polaron tunnelling （OLPT） model of ions is the most favorable mechanism for the ac conduction in the present glass system. The ac response, the dc conductivity and dielectric relaxation have the same activation energy and they originate from the same basic transport mechanism. The results of the dielectric permittivity show no maximum peak in the temperature and frequency range studied. This absence of maximum peak is an indication of non-ferroelectric behavior of all the studied samples. The MAE has been detected in the ac conductivity, which is the same as the classical MAE in the dc conductivity. The electrical parameters such as dielectric permittivity ε′ and real dielectric modulus M′ show a typical minimum deviation from linearity by about two orders of magnitude. The loss factor tanδ and the imaginary dielectric modulus M″ are insignificantly dependent on composition even at the same transition temperature Tg.

Aluminum matrix composites reinforced by molybdenum-coated carbon nanotubes

To extend the application of carbon nanotubes （CNTs） and explore novel aluminum matrix composites,CNTs were coated by molybdenum layers using metal organic chemical vapor deposition,and then Mo-coated CNT （Mo-CNT）/Al composites were prepared by the combination processes of powder mixing and spark plasma sintering.The influences of powder mixing and Mo-CNT content on the mechanical properties and electrical conductivity of the composites were investigated.The results show that magnetic stirring is better than mechanical milling for mixing the Mo-CNTs and Al powders.The electrical conductivity of the composites decreases with increasing Mo-CNT content.When the Mo-CNT content is 0.5wt%,the tensile strength and hardness of Mo-CNT/Al reach their maximum values.The tensile strength of 0.5wt% Mo-CNT/Al increases by 29.9%,while the electrical conductivity only decreases by 7.1%,relative to sintered pure Al.The phase analysis of Mo-CNT/Al composites reveals that there is no formation of Al carbide in the composites.

Performance improvement of continuous carbon nanotube fibers by acid treatment

Continuous CNT fibers have been directly fabricated in a speed of 50 m/h-400 m/h,based on an improved chemical vapor deposition method.As-prepared fibers are further post-treated by acid.According to the SEM images and Raman spectra,the acid treatment results in the compaction and surface modification of the CNTs in fibers,which are beneficial for the electron and load transfer.Compared to the HNO3 treatment,HClSO_3 or H_2SO_4 treatment is more effective for the improvement of the fibers＇ properties.After HCISO_3 treatment for 2 h,the fibers＇ strength and electrical conductivity reach up to-2 GPa and-4.3 MS/m,which are promoted by-200%and almost one order of magnitude than those without acid treatment,respectively.The load-bearing status of the CNT fibers are analyzed based on the downshifts of the G＇ band and the strain transfer factor of the fibers under tension.The results reveal that acid treatment could greatly enhance the load transfer and inter-bundle strength.With the HCISO3 treatment,the strain transfer factor is enhanced from-3.9%to-53.6%.

Mechanical, electrical, and thermal expansion properties of carbon nanotube-based silver and silver–palladium alloy composites

The mechanical, electrical, and thermal expansion properties of carbon nanotube（CNT）-based silver and silver–palladium（10：1, w/w） alloy nanocomposites are reported. To tailor the properties of silver, CNTs were incorporated into a silver matrix by a modified molecular level-mixing process. CNTs interact weakly with silver because of their non-reactive nature and lack of mutual solubility. Therefore, palladium was utilized as an alloying element to improve interfacial adhesion. Comparative microstructural characterizations and property evaluations of the nanocomposites were performed. The structural characterizations revealed that decorated type-CNTs were dispersed, embedded, and anchored into the silver matrix. The experimental results indicated that the modification of the silver and silver–palladium nanocomposite with CNT resulted in increases in the hardness and Young＇s modulus along with concomitant decreases in the electrical conductivity and the coefficient of thermal expansion（CTE）. The hardness and Young＇s modulus of the nanocomposites were increased by 30%？40% whereas the CTE was decreased to 50%-60% of the CTE of silver. The significantly improved CTE and the mechanical properties of the CNT-reinforced silver and silver–palladium nanocomposites are correlated with the intriguing properties of CNTs and with good interfacial adhesion between the CNTs and silver as a result of the fabrication process and the contact action of palladium as an alloying element.

Electrical properties of dry polycrystalline olivine mixed with various chromite contents: Implications for the high conductivity anomalies in subduction zones

Chromite,a crucial high-conductivity mineral phase of peridotite in ophiolite suites,has a significant effect on the electrical structure of subduction zones.The electrical conductivities of sintered polycrystalline olivine containing various volume percents of chromite(0,4,7,10,13,16,18,21,23,100 vol.%)were measured using a complex impedance spectroscopic technique in the frequency range of 10^(−1)-10^(6) Hz under the conditions of 1.0-3.0 GPa and 873-1223 K.The relationship between the conductivities of the chromite-bearing olivine aggregates and temperatures conformed to the Arrhenius equation.The positive effect of pressure on the conductivities of the olivine-chromite systems was much weaker than that of temperature.The chromite content had an important effect on the conductivities of the olivine-chromite systems,and the bulk conductivities increased with increasing volume fraction of chromite to a certain extent.The inclusion of 16 vol.%chromites dramatically enhanced the bulk conductivity,implying that the percolation threshold of interconnectivity of chromite in the olivine-chromite systems is-16 vol.%.The fitted activation enthalpies for pure polycrystalline olivine,polycrystalline olivine with isolated chromite,polycrystalline olivine with interconnected chromites,and pure polycrystalline chromite were 1.25,0.78-0.87,0.48-0.54,and 0.47 eV,respectively.Based on the chemical compositions and activation enthalpies,small polaron conduction was proposed to be the dominant conduction mechanism for polycrystalline olivine with various chromite contents.Furthermore,the conductivities of polycrystalline olivine with interconnected chromite(10-1.5-100.5 S/m)provides a reasonable explanation for the high conductivity anomalies in subduction-related tectonic environments.

Preparation and Characterization of the Zr/CuO Pyrotechnical Battery

A pyrotechnical battery is successfully prepared, including an anode and cathode having pyrotechnic charges with Zr, CuO and asbestos. The anode and cathode are separated by a separator formed from LiF, ZrO2, and a fibrous sponge. A digital phosphor oscilloscope （DPO） is used to analyze discharge characterization of the pyrotechnical battery. Then the properties of the electrode materials are characterized by EDS, SEM and a temperature recorder, respectively. The discharge mechanism and safety characteristic are also discussed. The results indicate that the combustion temperature of electrode materials is determined as 1 500.6 ℃ according to thermometry analysis （the case temperature of the battery is lower）. The combustion product is identified as ZrO2, Cu2O and Cu by X-ray diffraction （XRD）. When the diaphragm is completely melted, Li＋ migration and an embedded-based conductive process are formed. Then an electromotive force will immediately reach to the maximum. The discharge performance of the pyrotechnical battery then takes on stability. The electromotive force is up to 2.29 V, and that discharge time continues for more than 18 s. The current density in the small area （less than 2.88 Acm-2） is most effective. The conversion efficiency of electric energy is 96%. The pyrotechnical battery is very safe for the production and use processes.

Electronic Transport Properties of La_(2/3)Ca_(1/3)Mn_(0.98)Cu_(0.02)O_3 Sintered at Different Temperature

The sol-gel method was adopted to prepare series of La2/3Cal/3Mn0.98Cu0.02O3 samples sintered at different temperatures, and the structure of samples, high-temperature electrical conductive mechanism and electronic transport properties of double-peak resistance were investigated. X-ray diffraction pattern indicates that the samples are in perovskite structures and obey the Vari- able-Rang Hopping Mechanism of p = p 0exp[（T0/T）^1/4] under high temperatures during the electrical conduction. In addition, based on the polycrystalline granular system surface and image, the reasonable explanation was given for the double-peak resistance phemomenon.