Cerium Methacrylate Assisted Preparation of Highly Thermally Conductive and Anticorrosive Multifunctional Coatings for Heat Conduction Metals Protection

Preparing polymeric coatings with well corrosion resistance and high thermal conductivity(TC)to prolong operational life and ensure service reliability of heat conductive metallic materials has long been a substantive and urgent need while a difficult task.Here we report a multifunctional epoxy composite coating(F-CB/CEP)by synthesizing cerium methacrylate and ingeniously using it as a novel curing agent with corrosion inhibit for epoxy resin and modifier for boron nitride through"cation-π"interaction.The prepared F-CB/CEP coating presents a high TC of 4.29 W m^(−1)K^(−1),which is much higher than other reported anti-corrosion polymer coatings and thereby endowing metal materials coated by this coating with outstanding thermal management performance compared with those coated by pure epoxy coating.Meanwhile,the low-frequency impedance remains at 5.1×10^(11)Ωcm^(2)even after 181 days of immersion in 3.5 wt%NaCl solution.Besides,the coating also exhibits well hydrophobicity,self-cleaning properties,temperature resistance and adhesion.This work provides valuable insights for the preparation of high-performance composite coatings with potential to be used as advanced multifunctional thermal management materials,especially for heat conduction metals protection.

The research on the high strength and anti-arc ablation coatings applied in steel conductive rail

In order to enhance the ablation-resistant performance of stainless-steel conductive rails,Mo coating,410 stainless steel coating and 15 wt%Cr_(2)AlIC particles reinforced 410 stainless steel composite coating were prepared and evaluated.Different from the weak interfacial strength caused by the dissimilar metals between Mo and steel rails,410 stainless steel coating has better interfacial contact with steel rails.The introduction of Cr_(2)AlC into 410 stainless steels further strengthened the mechanical properties of coating by alloy strengthening effect and particle strengthening effect,as the decomposition of Cr_(2)AlC into nano CrC particles is accompanied with the diffusion of Al atoms into 410 stainless steels.It was found that the composite coating can still resist arc erosion at 150 A current,as a dense oxide film formed during the ablation process and the decomposition of Cr_(2)AlC contributed to the heat absorption.

Improvement strategy on thermophysical properties of A_(2)B_(2)O_(7)-type rare earth zirconates for thermal barrier coatings applications:A review

The A_(2)B_(2)O_(7)-type rare earth zirconate compounds have been considered as promising candidates for thermal barrier coating(TBC) materials because of their low sintering rate,improved phase stability,and reduced thermal conductivity in contrast with the currently used yttria-partially stabilized zirconia (YSZ) in high operating temperature environments.This review summarizes the recent progress on rare earth zirconates for TBCs that insulate high-temperature gas from hot-section components in gas turbines.Based on the first principles,molecular dynamics,and new data-driven calculation approaches,doping and high-entropy strategies have now been adopted in advanced TBC materials design.In this paper,the solid-state heat transfer mechanism of TBCs is explained from two aspects,including heat conduction over the full operating temperature range and thermal radiation at medium and high temperature.This paper also provides new insights into design considerations of adaptive TBC materials,and the challenges and potential breakthroughs are further highlighted for extreme environmental applications.Strategies for improving thermophysical performance are proposed in two approaches:defect engineering and material compositing.

Bonding strength of graded anti-corrosive coatings of fluoroethylenepropylene (FEP)/polyphenylene sulfide (PPS)

Fluororesin-based anti-corrosive coatings including graded FEP/PPS were prepared on carbon steel by melt powder coating, the bonding strength of all coating systems was determined by the pull-off test. It is found that the poor adhesion of fluororesin coatings to metallic substrates is improved obviously by the graded coating structure of FEP/PPS, and the bonding strength reaches up to 11.8 MPa for the five-layer system. Examination by electron probe microanalysis （EPMA） verifies that the distribution of main components is graded in the five-layer system, which is responsible for the enhancement of the interfacial bonding.

Preparation of PbTiO_3 Conductive Powders and Coatings

La2O3 and Ce2O3 were penetrated into PbTiO3 to obtain conductive powders, and then they were mixed with polyurethane and butyl acetate to prepare conductive coatings. The results showed that the electric property of modified PbTiO3 powders was improved by penetration of La2O3 and Ce2O3. XRD patterns showed that some new compounds such as La2Ti6O15, CeTi21O38 and Pb0.634La0.209Ti0.948O2.284 were formed, which led to the rapid increase of conductivity. The resistivity of modified PbTiO3 powders decreased to 3.88 Ω·m. The coatings using modified PbTiO3 powders as fillings also had a good conductivity. When the PbTiO3 powders were 10% and antisettle agent (bentonite) content was 0.50%, and mass ratio between polyurethane and butyl acetate was 1.05, the surface resistivity of the coatings fell down to 1.3×108 Ω·m. This kind of conductive coatings could be used in electromagnetic shielding.

Corrosion resistance and electrical conductivity of V/Ce conversion coating on magnesium alloy AZ31B

A V/Ce conversion coating was deposited in the surface of AZ31B magnesium alloy in a solution containing vanadate and cerium nitrate.The coating composition and morphology were examined.The conversion coating appears to consist of a thin and cracked coating with a scattering of spherical particles.The corrosion behavior of the substrate and conversion coating was studied by potentiodynamic polarization and electrochemical impedance spectroscopy (EIS).Compared with AZ31B magnesium alloy,the corrosion current density of the conversion coating is decreased by two orders of magnitude.The total impedance of the V/Ce conversion coating rise to 1.6×10^(3)Ω·cm^(2)in contrast with2.2×10^(2)Ω·cm^(2)of the bare AZ31B.In addition,the electrical conductivity of the coating was assessed by conductivity meter and Mott-Schottky measurement.The results reveal a high dependence of the conductivity of the coating on the semiconductor properties of the phase compositions.

Thermal conductivity of (Sm_(1-x)La_x)_2Zr_2O_7 (x=0,0.25,0.5,0.75 and 1) oxides for advanced thermal barrier coatings

Pyrochlore oxides of general compositions, A2Zr2O7, where A is a 3＋ cation （La to Lu）, are promising candidate materials for applications as high temperature thermal barrier coatings because of their high melting points, high thermal expansion coefficients, and low thermal conductivities. In this study, oxides of Sm2Zr2O7, （Smo.75La0.25）2Zr2O7, （Sm0.5 La0.5）2 ZreO7, （Sm0.25La0.75）eZr2O7 and La2Zr2O7 were prepared by solid reactions at 1600℃ for 10 h using Sm2O3, La2O3 and ZrO2 as the reactants. The phase compositions of these ceramic materials were analyzed by X-ray diffractometer （XRD） and fourier transform infrared spectroscopy （FT-IR） methods, respectively. The microstructure was observed by scanning electron microscope （SEM）. The thermal conductivities of these ceramic materials were measured using laser-flash method. XRD and FT-IR results showed that pure ceramic materials with pyrochlore structure were prepared successfully. SEM results indicated that microstructures of these ceramic materials were dense and grain boundaries were very clean. The La2O3 doped Sm2Zr2O7 pyrochlores （Sm0.75 La0.25）2Zr2O7 and （Sm0.5 La0.5）2 Zr2O7 had lower thermal conductivity than the undoped Sm2Zr2O7. The thermal conductivity of （Sm0.25La0.75）2Zr2O7 was found to be lower than that of La2Zr2O7. The results showed that these ceramic materials had the potential to be used as candidate materials for TBCs.

Predicted interfacial thermal conductance and thermal conductivity of diamond/Al composites with various interfacial coatings

The interfacial thermal conductance （ITC） and thermal conductivity （TC） of diamond/Al composites with various coatings were theoretically studied and discussed. A series of predictions and numerical analyses were performed to investigate the effect of thickness, sound velocity, and other parameters of coating layers on the ITC and TC. It is found that both the ITC and TC decline with increasing coating thickness, especially for the coatings with relatively low thermal conductivity. Nevertheless, if the coating thickness is close to zero, or quite a small value, the ITC and TC are mainly determined by the constants of the coating material. Under this condition, coatings such as Ni, TiC, Mo 2 C, SiC, and Si can significantly improve the ITC and TC of diamond/Al composites. By contrast, coatings like Ag will exert the negative effect. Taking the optimization of interfacial bonding into account, conductive carbides such as TiC or Mo 2 C with low thickness can be the most suitable coatings for diamond/Al composites.

Preparation technology and anti-corrosion performances of black ceramic coatings formed by micro-arc oxidation on aluminum alloys

In order to prepare ornamental and anti-corrosive coating on aluminum alloys, preparation technology of black micro-arc ceramic coatings on Al alloys in silicate based electrolyte was studied. The influence of content of Na2WO4 and combination additive in solution on the performance of black ceramic coatings was studied; the anticorrosion performances of black ceramic coatings were evaluated through whole-immersion test and electrochemical method in 3.5% NaCl solution at different pH value; SEM and XRD were used to analyze the surface morphology and phase constitutes of the black ceramic coatings. Experimental results indicated that, without combination additives, with the increasing of Na2WO4 content in the electrolyte, ceramic coating became darker and thicker, but the color was not black; after adding combination additive, the coating turned to be black; the black ceramic coating was multi-hole form in surface. There was a small quantity of tungsten existing in the black ceramic coating beside α-Al2O3 phase and β-Al2O3 phase. And aluminum alloy with black ceramic coating exhibited excellent anti-corrosion property in acid, basic and neutral 3.5% NaCl solution.

High-Thermal Conductive Coating Used on Metal Heat Exchanger

Based on modified silicon polyester resin in addition to several functional fillers such as corrosion-resistant fillers, heat-resistant fillers and thermal conductive fillers, a high thermal conductive coating can be made. On the basis of boronnitride(BN) and aluminum nitride(AIN) used as thermal conductive fillers and by means of the testing system of hot disk and heat transfer experiment, researches on the varieties of thermal conductive fillers and the effects of the contents of high-thermal conductive coating have been done, which shows that the thermal conductivity of coating increases with the increase of the quality fraction and the coefficient of thermal conductivity of the thermal conductive fillers of coating. With guaranteeing better heat resistance, stronger corrosion resistance and adhesive force, the coefficient of coating can reach a level as high as 3 W·m-1·K-1.

Development of anti-corrosive coating on AZ31 Mg alloy subjected to plasma electrolytic oxidation at sub-zero temperature

Plasma electrolytic oxidation(PEO)is a promising surface treatment to generate adherent and thick anti-corrosive coating on light-weight metals(Al,Mg,Ti,etc.)using an eco-friendly alkaline electrolyte.High energy plasma,however,inevitably generates porous structures that limit their practical performance.The present study proposes a straight-forward simple method by utilizing sub-zero electrolyte(268 K)to alter the plasma characteristics during formation of the protective coating on AZ31 Mg alloy via PEO with a comparison to the electrolyte at room temperature(298 K).In refrigerated electrolyte,the formation of micro-defects is suppressed relatively at the expense of low coating growth,which is measured to be twice lower than that at 298 K due to the temperature-dependent soft plasma discharges contributing to the development of the present coating.As a consequence,corrosion resistance of the sample processed at 268 K is superior to that of 298K,implying that the effect of coating thickness is less dominant than that of compactness.This phenomenon is interpreted in relation to the ionic movement and oxide solidification controlled by soft plasma discharges arising from the temperature gradient between electrolyte and surface of the substrate during PEO.

Effect of single Si_(1−x)C_(x)coating and compound coatings on the thermal conductivity and corrosion resistance of Mg-3Sn alloy

A single Si_(1−x)C_(x)coating and compound coatings were deposited on Mg-3Sn matrix alloy by magnetron sputtering method.Compound coatings included Mg or Mg/AlTi intermediates between Mg-3Sn substrate and Si_(1−x)C_(x)coating.The thermal conductivity of the Mg-3Sn alloy after coating was enhanced at room temperature.The results showed that the Mg-3Sn alloy coated with Mg/AlTi/Si_(1−x)C_(x)displayed higher thermal conductivity,its thermal conductivity after corrosion was 90.1 W/(m K)and 108.4 W/(m K)at 25℃and 100℃,respectively.Meanwhile,it was revealed that the Mg/Si_(1−x)C_(x)and Mg/AlTi/Si_(1−x)C_(x)compound coatings had nobler Ecorr and much lower i_(corr),higher Rp,compared with the bare Mg-3Sn and Mg-3Sn/Si_(1−x)C_(x)system,and improved the corrosion resistance of the magnesium substrate.

An electrochemical method for evaluating the resistance to cathodic disbondment of anti-corrosion coatings on buried pipelines

Methods for evaluating the resistance to cathodic disbondment （RCD） of anti-corrosion coatings on buried pipelines were reviewed. It is obvious that these traditional cathodic disbondment tests （CDT） have some disadvantages and the evaluated results are only simple figures and always rely on the subjective experience of the operator. A new electrochemical method for evaluating the RCD of coatings, that is, the potentiostatic evaluation method （PEM）, was developed and studied. During potentiostatic anodic polarization testing, the changes of stable polarization current of specimens before and after cathodic disbonding （CD） were measured, and the degree of cathodic disbondment of the coating was quantitatively evaluated, among which the equivalent cathodic disbonded distance AD was suggested as a parameter for evaluating the RCD. A series of testing parameters of the PEM were determined in these experiments.

Investigation of anti-corrosion property of hybrid coatings fabricated by combining PEC with MAO on pure magnesium

Novel hybrid coatings on pure magnesium were prepared by combining plasma electrolytic carburizing(PEC)with micro-arc oxidation(MAO)to further enhance the anti-corrosion property in this paper.Scanning electron microscopy(SEM)was used to observe the microstructure of the coatings,meanwhile,energy dispersive spectrometry(EDS)and X-ray diffraction(XRD)were separately used to investigate the elemental as well as phase compositions of the coatings.The anti-corrosion property of the coatings was evaluated by potentiodynamic polarization curves as well as electrochemical impedance spectroscopy(EIS).The results show that PEC process is closely related with the effects of adsorption as well as diffusion of the activated carbon atoms,and it can provide a favorable pretreatment surface with predesigned chemical composition to obtain a new kind of phase,namely Si C with superior corrosion resistance and chemical stability,in the following PEC+MAO hybrid coatings.Meanwhile,PEC preprocessing also can afford an excellent micro-structure to increase the coating thickness as well as to improve the compactness of the PEC+MAO hybrid coatings.During the fabrication process of the PEC+MAO hybrid coatings,an overlapping phenomenon in regard to coating thickness can be observed instead of heaping up layer by layer.Compared with both single PEC surface modification layers as well as single MAO coatings,the PEC+MAO hybrid coatings exhibit more superior anti-corrosion property.Especially,the EIS data reveal that the PEC+MAO hybrid coatings can act as an effective protection system to provide relatively excellent long-range anti-corrosion protection.Note also that employing same MAO technique for both single MAO treatment as well as PEC+MAO combining procedure is the key to this research.

Influence of graphene on the anti-corrosion performance of epoxy-based coatings

In this work, graphene-modified epoxy-based anti-corrosion coatings were prepared and the influence of graphene on the anti-corrosion performance of the epoxy-based coatings was investigated with water contact angle test ,chemical solution immersion test, and electrochemical test. The water contact angle and chemical solution resistance of the epoxy-based coatings were improved with an increase in graphene content from 0 to 0.4%. These results prove that addition of graphene can significantly improve the hydrophobicity and impermeability of epoxy- based coatings. However, when the graphene content was increased to 0.5%, the performance of the epoxy-based coatings decreased because of graphene aggregation. Tafel polarization results show that graphene addition can significantly reduce the corrosion current density and corrosion potential of epoxy-based coatings, which enhance their anti-corrosion performance.

Effects of Shielding Coatings on the Anode Shaping Process during Counter-rotating Electrochemical Machining

Electrochemical machining （ECM） has been widely used in the aerospace, automotive, defense and medical industries for its many advantages over traditional machining methods. However, the machining accuracy in ECM is to a great extent limited by the stray corrosion of the unwanted material removal. Many attempts have been made to improve the ECM accuracy, such as the use of a pulse power, passivating electrolytes and auxiliary electrodes. However, they are sometimes insufficient for the reduction of the stray removal and have their limitations in many cases. To solve the stray corrosion problem in CRECM, insulating and conductive coatings are respectively used. The different implement processes of the two kinds of coatings are introduced. The effects of the two kinds of shielding coatings on the anode shaping process are investigated. Numerical simulations and experiments are conducted for the comparison of the two coatings. The simulation and experimental results show that both the two kinds of coatings are valid for the reduction of stray corrosion on the top surface of the convex structure. However, for insulating coating, the convex sidewall becomes concave when the height of the convex structure is over 1.26 ram. In addition, it is easy to peel off by the high-speed electrolyte. In contrast, the conductive coating has a strong adhesion, and can be well reserved during the whole machining process. The convex structure fabricated by using a conductive iron coating layer presents a favorable sidewall profile. It is concluded that the conductive coating is more effective for the improvement of the machining quality in CRECM. The proposed shielding coatings can also be employed to reduce the stray corrosion in other schemes of ECM.

Preparation and thermal conductivity of tungsten coated diamond/copper composites

Tungsten was plated on the surface of diamond by using thermal diffusion method.Different process parameters were employed to prepare the composites with tungsten,diamond and copper.The micro morphology of different samples was observed,and the thermal conductivity of samples was measured by laser flash method.The optimal process parameters for preparing diamond/copper composites with high thermal conductivity were investigated.The results indicated that plating tungsten on diamond could modify the interface bonding.When the diamond was plated for 60 min,the coating appeared intact,uniform and flat,and the thermal conductivity of the sample could reach as high as 486 W/(m·K).The integrity and uniformity were more important than thickness for the coating.When the tungsten-plated diamond was further annealed,the metallurgical bonding between the coating and the diamond was enhanced,and the thermal conductivity rose to 559 W/(m·K).

Microstructure and electrical conductivity of electroless copper plating layer on magnesium alloy micro-arc oxidation coating

In order to impart electrical conductivity to the magnesium alloy micro-arc oxidation(MAO)coating,the electroless copper plating was performed.Effects of plating temperature and complexing agent concentration on the properties of the electroless copper plating layers were studied by measuring their microstructure,corrosion resistance and electrical conductivity.It was found that the optimized plating temperature was 60°C,and the most suitable value of the complexing agent concentration was 30 g/L.Under this condition,a complete and dense plating layer could be obtained.The formation mechanism of the plating layer on magnesium alloy MAO coating was analyzed.A three-stage model of the plating process was proposed.The square resistance of the plated specimen was finally reduced to 0.03Ω/□after the third stage.Through electroless copper plating,the MAO coated sample obtained excellent electrical conductivity without significantly reducing its corrosion resistance.

Effect of ZrO_2 (9mol% Y_2O_3) coating thickness on the electronic conductivity of Mg-PSZ oxygen sensors

The ZrO2 (9mol% Y2O3) coating was prepared evenly on the surface of MgO partially stabilized zirconia (Mg-PSZ) tube (oxygen sensor probe) by dipping the green Mg-PSZ tube in a ZrO2 (9mol% Y2O3) slurry and then co-firing at 1750°C for 8 h. The double-cell method was employed to measure the electronic conductivity parameter and exam the reproducibility of the coated Mg- PSZ tube. The experimental results indicate that the good thermal shock resistance of the Mg-PSZ tube can be retained when the coating thickness is not more than 3.4 μm. The ZrO2 (9mol% Y2O3) coating reduces the electronic conductivity parameter remarka- bly, probably due to the lower electronic conductivity of Y2O,-stabilized ZrO2 than that of MgO-stabilized ZrO2. Moreover, the ZrO2 (9mol% Y2O3) coating can improve the reproducibility and accuracy of the Mg-PSZ tube significantly in the low oxygen measure- ment. The smooth surface feature and lower electronic conductivity of the coated Mg-PSZ tube should be responsible for this im- provement.

Density Dependence of Tunnel Fire Resistance for Aerogel-Cement Mortar Coatings

Five kinds of mortars with density grades of 500, 600, 700, 800, and 900 kg/m3 were prepared. Their thermal conductivity and compressive strength were measured, and the morphological changes before and after simulated tunnel fire were observed. To investigate the fire resistance, the interfacial temperature of a 30 mm thick aerogel-cement mortar and self-compacting concrete (SCC) in a simulated tunnel fire with the maximum temperature of 1100 ℃ for 2.5 h was tested and recorded. The results showed that as the density decreased, both compressive strength and thermal conductivity of the aerogel-cement mortar exhibited an exponential decrease. The effective fire resistance time of the mortar with 500, 600, 700, 800, and 900 kg/m^3 for protecting SCC from tunnel fire were 97 min, 114 min, 144 min, > 150 min, 136 min, respectively. 700 - 800 kg/m3 was the optimum density for engineering application of tunnel concrete fireproof coating.