一种CC/CV平滑切换的宽输出电压充电电路

目前多种动力蓄电池凭借着能量密度高、续航里程长和可循环使用等优势,在新能源汽车领域得到了广泛应用。针对当前以谐振电路为基础构建复合变换器应用于蓄电池充电存在输出电压范围、模式间切换、效率等不同问题,提出了一种四开关Buck-Boost与电容钳位LLC级联复用式变换器作为充电电路。该电路增益曲线的容性区和感性区均可工作,宽调频范围的容性区具有恒流特性,感性区的最佳谐振点具有恒压特性,利于实现蓄电池恒流恒压充电控制。频率与占空比的解耦控制拓宽了变换器的输出电压范围,且负载阻抗连续变化下电压增益连续,利于实现蓄电池恒流恒压平滑切换及满足不同电池充电控制方案,宽增益下的宽调控范围可减少输出纹波。拥有桥臂间移相软开关、复用桥臂增强软开关能力和降低通态电流、变压器低磁链及最终移动于最佳谐振点工作等电路特性,利于实现电能高效传输。仿真与实验结果验证了充电电路全程满足ZVS、ZCS的恒流恒压控制及充电模式间平滑切换特性。

LCC-LCC/S自切换恒流-恒压复合型无线电能传输系统

为了解决蓄电池充电过程中的恒流过充或恒压欠充问题,该文提出一种LCC-LCC/S自切换恒流-恒压复合型无线电能传输系统。通过副边电力开关切换,该系统不仅可实现恒流-恒压输出,且能有效应对蓄电池充电过程中的各种异常工况;另外,在充电完成负载移除时,该系统能自动进入低功耗待机状态。首先,给出LCC-LCC/S自切换复合拓扑,分析恒压-恒流及零相角(ZPA)特性;其次,分析恒流-恒压切换点并验证其最优性;然后,通过分析充电过程中出现的副边缺失、负载短路、负载断路等异常工况,系统能通过开关切换有效应对以上异常工作情况,并且充电完成负载移除后系统能自动进入低功耗待机状态;接着,通过与目前研究较多的S-SP拓扑的系统特性进行对比,突出了LCC-LCC/S拓扑的优势;最后,搭建仿真和实验平台,实现最大电流为5.03 A、最大电压为48.92 V的高效率输出,验证了所提理论的正确性。

基于频率切换实现电池恒流和恒压充电的LCC-S补偿WPT系统研究

无线电能传输WPT(wireless power transfer)系统具有安全、方便、美观等性能优势,已逐步渗入到人们的日常生活中。在电池充电应用中,通常期望WPT系统能够在零相角ZPA(zero phase angle)条件下实现负载无关的恒流和恒压充电功能。提出了一种基于频率切换的LCC-S补偿WPT系统及其参数设计方法,可使系统在2个不同的ZPA频率点分别实现负载无关的恒流和恒压充电输出,无需改变电路拓扑结构。设计的LCC-S补偿WPT系统接收侧仅有一个补偿电容,确保了WPT系统接收侧紧凑性。最后,搭建了一台充电电流和电压分别为3 A和50 V的实验样机,验证了本研究中WPT系统的合理性与实用性。

Dynamics and stabilization of peak current-mode controlled buck converter with constant current load

The discrete iterative map model of peak current-mode controlled buck converter with constant current load（CCL）,containing the output voltage feedback and ramp compensation, is established in this paper. Based on this model the complex dynamics of this converter is investigated by analyzing bifurcation diagrams and the Lyapunov exponent spectrum. The effects of ramp compensation and output voltage feedback on the stability of the converter are investigated. Experimental results verify the simulation and theoretical analysis. The stability boundary and chaos boundary are obtained under the theoretical conditions of period-doubling bifurcation and border collision. It is found that there are four operation regions in the peak current-mode controlled buck converter with CCL due to period-doubling bifurcation and border-collision bifurcation. Research results indicate that ramp compensation can extend the stable operation range and transfer the operating mode, and output voltage feedback can eventually eliminate the coexisting fast-slow scale instability.

基于LCC-S补偿式谐振拓扑的锂电池WPT系统研究

无线电能传输(wireless power transfer,WPT)系统具有安全、可靠、方便等优点。文章在分析WPT系统锂离子电池内阻及其典型充电方式的基础上,通过对WPT原理和谐振拓扑结构的研究,提出了基于LCC-S补偿式谐振拓扑的WPT系统。在电池等效负载变化的情况下,通过合理的参数设计,LCC-S补偿式谐振拓扑结构可以分别实现与负载无关的恒流模式和恒压模式,无需切换拓扑结构。在理论分析的基础上,设计了系统的参数,并通过MATLAB仿真系统搭建仿真模型,验证了研究中的恒流模式和恒压模式。

Low voltage substrate current： a monitor for interface states generation in ultra-thin oxide n-MOSFETs under constant voltage stresses

The low voltage substrate current （Ib） has been studied based on generation kinetics and used as a monitor of interface states （Nit） generation for ultra-thin oxide n-MOSFETs under constant voltage stress. It is found that the low voltage Ib is formed by electrons tunnelling through interface states, and the variations of Ib（△Ib） are proportional to variations of Nit （△Nit）. The Nit energy distributions were determined by differentiating Nit（Vg）. The results have been compared with that measured by using gate diode technique.

Field-induced phase transitions in chiral smectic liquid crystals studied by the constant current method

In ferroelectric liquid crystals, phase transitions can be induced by an electric field. The current constant method allows these transition to be quickly localized and thus the（E, T） phase diagram of the studied product can be obtained.In this work, we make a slight modification to the measurement principles based on this method. This modification allows the characteristic parameters of ferroelectric liquid crystal to be quantitatively measured. The use of a current square signal highlights a phenomenon of ferroelectric hysteresis with remnant polarization at null field, which points out an effect of memory in this compound.

Numerical Solution of MHD Convection and Mass Transfer Flow of Viscous Incompressible Fluid about an Inclined Plate with Hall Current and Constant Heat Flux

The present numerically study investigates the influence of the Hall current and constant heat flux on the Magneto hydrodynamic (MHD) natural convection boundary layer viscous incompressible fluid flow in the manifestation of transverse magnetic field near an inclined vertical permeable flat plate. It is assumed that the induced magnetic field is negligible compared with the imposed magnetic field. The governing boundary layer equations have been transferred into non-similar model by implementing similarity approaches. The physical dimensionless parameter has been set up into the model as Prandtl number, Eckert number, Magnetic parameter, Schmidt number, local Grashof number and local modified Grashof number. The numerical method of Nactsheim-Swigert shooting iteration technique together with Runge-Kutta six order iteration scheme has been used to solve the system of governing non-similar equations. The physical effects of the various parameters on dimensionless primary velocity profile, secondary velocity profile, and temperature and concentration profile are discussed graphically. Moreover, the local skin friction coefficient, the local Nusselt number and Sherwood number are shown in tabular form for various values of the parameters.

Multi-stage constant current charging strategy considering SOC intervals and voltage thresholds

Conventional multi-stage constant current charging strategies often use higher multiples of current to charge the battery in pursuit of shorter charging times.However,this leads to an increase in battery temperature,while shortening the charging time.This in turn affects the safety of the charging process.Furthermore,the higher charging currents are not ideal for shortening the charging time in the later stages of charging.To solve the aforementioned problems,in this study,a multi-stage constant current charging strategy is presented.This strategy can shorten the battery charging time by using the increase in battery temperature during the charging process as a constraint,using a genetic algorithm to calculate the charging current value,and investigating the phased approach to charging.Finally,the charging strategy is experimentally validated at different ambient temperatures and different initial SOCs.The experimental results show that the charging strategy proposed in this paper not only reduces the amount of calculations,but also reduces the temperature rise by up to 46.4%and charging time by up to 4.2%under different operating conditions.

基于频率切换的LCC-S型IPT系统恒流/恒压输出研究

为实现感应电能传输(Inductive Power Transfer,IPT)系统在变负载条件下的恒流/恒压高效输出,提出一种基于频率切换的LCC-S型IPT系统参数配置及优化方法。从LCC-S补偿拓扑入手,分别得到系统恒流或恒压零相位角(Zero Phase Angle,ZPA)输出的条件方程,并推导了电流增益、电压增益与系统参数之间的定量关系;进一步通过定义系统的输出增益比,分析了恒流/恒压模式下输出增益、负载电阻与整体效率的关系;在此基础上,通过选取最佳的输出增益值,使得系统整体效率达到了全局最大化。仿真结果表明,负载电阻在3~300Ω的变化范围内包括恒流/恒压模式切换瞬间都能保持稳定的输出,并且恒流/恒压模式下均能实现ZPA运行,同时系统整体效率都维持在90%以上。

High Frequency Oscillator Design Using a Single 45 nm CMOS Current Controlled Current Conveyor (CCCII+) with Minimum Passive Components

In the field of analog VLSI design, current conveyors have reasonably established their identity as an important circuit design element. In the literature published during the past few years, numerous application have been reported which are based on a variety of current conveyors. In this paper, an oscillator circuit has been proposed. This oscillator is designed using a single positive type second generation current controlled current conveyor (CCCII+). A CCCII has parasitic input resistance on it’s current input node. This resistance could be exploited to reduce circuit complexities. Thus in this accord, a novel oscillator circuit is proposed which utilizes the parasitic resistance of the CCCII+ along with a few more passive components.

LCC-HVDC系统整流–逆变交互振荡模式稳定变化特征及机理研究

LCC-HVDC系统联接弱交流系统时,整流站和逆变站之间存在强交互作用。研究发现,对于弱交流系统场景,LCC-HVDC的整流侧和逆变侧交流系统在不同短路比(short-circuit ratio,SCR)组合下,系统稳定性由整流–逆变交互振荡模式主导,且随定电流控制参数的改变呈现“单调–非单调”更迭现象。该文通过阻尼比特性曲线和参数灵敏度研究该“单调–非单调”更迭现象的产生机理,指出该现象是由两端交流系统强度相互制约下的整流–逆变强交互作用导致,体现出系统稳定性趋势的“木桶效应”,即LCC-HVDC系统的稳定性趋势由所联接交流系统强度弱的一侧换流站主导。基于PSCAD/EMTDC的详细电磁暂态仿真,验证整流–逆变交互振荡模式稳定变化趋势的“单调–非单调”更迭现象。该研究可为掌握实际工程交互作用振荡模式及选取合理控制参数提供理论支撑。

An improved analysis method of constant-current charge/discharge curves and its application to nickel hydroxide electrode

The derivative of charge and discharge curves (d t /d E vs E plot) can be used to describe the charge and discharge process more exactly. The d t /d E ? 獷 plots of nickel hydroxide electrode at different charge/discharge rates and intermittent discharge experiment are discussed. Though the d t /d E ? 獷 plot is affected by many factors, it clearly has intrinsic relation with the nature of active material such as conductivity and thermodynamic potential of active material, which changes with the state of charge. The d t /d E—E plot can also be applied to other electrochemical active materials, especially to those having several phases during charge or discharge.

An Adaptive Response Compensation Technique for the Constant-Current Hot-Wire Anemometer

An adaptive response compensation technique has been proposed to compensate for the response lag of the constant-current hot-wire anemometer (CCA) by taking advantage of digital signal processing technology. First, we have developed a simple response compensation scheme based on a precise theoretical expression for the frequency response of the CCA (Kaifuku et al. 2010, 2011), and verified its effectiveness experimentally for hot-wires of 5 μm, 10 μm and 20 μm in diameter. Then, another novel technique based on a two-sensor probe technique—originally developed for the response compensation of fine-wire thermocouples (Tagawa and Ohta 1997;Tagawa et al. 1998)—has been proposed for estimating thermal time-constants of hot-wires to realize the in-situ response compensation of the CCA. To demonstrate the usefulness of the CCA, we have applied the response compensation schemes to multipoint velocity measure- ment of a turbulent wake flow formed behind a circular cylinder by using a CCA probe consisting of 16 hot-wires, which were driven simultaneously by a very simple constant-current circuit. As a result, the proposed response compensation techniques for the CCA work quite successfully and are capable of improving the response speed of the CCA to obtain reliable measurements comparable to those by the commercially-available constant-temperature hot-wire anemometer (CTA).

恒流源三侧向电阻率测井模块研制及应用

为进一步提高砂岩型铀矿地层电阻率参数在测井解释中的应用效果,尤其是对泥砂泥交互薄层的精细测量与识别,研究了基于OPA547放大器的恒流源三侧向电阻率测井模块,通过设计以OPA547为恒流激励源的数字激励控制电路,实现了正弦激励信号的恒流输出;设计了正弦检测信号的恒流反馈电路,实现恒流源的负反馈稳定输出;设计了交流电压检测电路,实现了交流信号的低通滤波与信号半波整流;最后,在实验室利用标准刻度器进行了研制模块的系数刻度,且在砂岩型铀矿钻孔进行了实际测井应用对比。经对比分析,研制的恒流源三侧向电阻率测井模块能够与砂岩铀矿综合测井中的其他参数组合使用,输出激励电流可调,对岩性及岩性界面具有较高的识别能力,对于交互薄层、钙质夹层等地层岩性变化的响应显示明显。

基于变频重构S/SP拓扑的无线电能传输系统恒流恒压研究

针对电动汽车无线充电系统耦合系数和负载变化导致系统输出电流和电压剧烈波动的问题,提出一种由交错叠放式线圈结构和变频重构控制策略组成的无线电能传输系统,通过重构补偿拓扑,并切换工作频率,实现了系统的恒流恒压输出。首先,分析了拓扑重构前后系统的恒流、恒压输出特性和零相角特性,对比恒流恒压工作模式下补偿电容的大小,给出了系统参数调整方法。其次,剖析了交错叠放式线圈结构模型,提出基于耦合系数波动最小原则的线圈结构优化策略。所提出的系统补偿元件较少,两个工作频率点符合国际标准。最后,搭建一套500 W的实验样机,验证系统的可行性和有效性。实验结果表明,交错叠放式线圈在X轴方向偏移发射线圈外径的55%(187mm)或Y轴方向偏移120mm时,耦合系数波动率小于5%。系统在恒流模式下电流波动率为3.58%,在恒压模式下电压波动率为4.83%,满足无线充电系统恒流恒压需求。

基于频率切换实现恒流/恒压输出的电场耦合无线电能传输系统

电场耦合无线电能传输(electric-field coupled wireless power transfer,EC-WPT)技术的实际应用中,有些用电设备需要系统具有不同的恒定输出特性(恒流/恒压),即系统输出电压或输出电流与负载解耦,此外,系统还需具备在恒流、恒压模式间按需切换的功能。针对该需求,基于LC-CLC谐振网络提出1种具有恒流/恒压输出特性的EC-WPT系统,分析LC-CLC谐振网络特性,推导恒流/恒压输出特性的实现条件以及恒流频率和恒压频率的计算方法,并给出系统参数设计方法,分析系统对工作频率的敏感性。最后通过仿真和实验验证所提出的EC-WPT系统恒流/恒压输出特性及其参数设计方法的正确性和有效性。实验结果表明所提出的系统在输入电压恒定的不同负载工况下分别实现2 A的恒流输出以及96 V的恒压输出,其最大传输效率分别为87.83%及88.17%。

基于改进型ZVT Buck电路的IPT充电系统设计

为了避免在感应式无线电能传输系统的耦合机构中增加多余的开关器件以及额外的无源元件,同时减小系统工作在高频率、大功率时全控型开关器件存在的开关损耗,提出基于改进型ZVT Buck电路闭环控制的方法实现对电池的恒流、恒压充电,通过分析改进型ZVT Buck电路的工作模态以及对电路参数的设计,确保在整个充电过程中DC-DC变换器均工作在软开关状态,最后搭建充电电流为35 A、充电电压为370 V的实验平台验证该方法的可行性。结果表明:该方法控制简单,并且降低了系统电路结构的复杂度,传输效率相对较高,能够满足恒流恒压充电需求。

基于自抗扰控制的圆纬机恒张力输纱控制系统设计

针对当前圆纬机积极式送纱方式中存在的纱线张力及输送速度不可任意调节、纱线张力波动大等问题,提出了一种可为圆纬机输送恒定张力纱线的输纱控制系统。构建了以无刷直流电动机速度环为内环、以纱线张力为外环的纱线恒张力双闭环反馈控制系统,通过自抗扰控制技术获取纱线实时动态指标,并对无刷直流电动机目标转速进行调整,最后通过磁场定向控制技术驱动无刷直流电动机。详细阐述了纱线张力的形成机制、纱线恒张力输送控制方案、系统硬件设计及控制算法。输纱测试表明,该控制系统可实现多种类型纱线的恒定张力输送。其中,棉纱张力波动标准差为1.5 cN(300 m/min测试条件),氨纶包芯纱的张力波动标准差为0.33 cN(240 m/min测试条件)。输纱速度的调节范围为0~600 m/min,纱线张力的控制范围为2.0~50.0 cN。