China is the world’s largest producer of copper processing products as well as the world’s largest copper consumer market.In 2013,China produced more than 13.60 million tons of copper processing products,accounting ...China is the world’s largest producer of copper processing products as well as the world’s largest copper consumer market.In 2013,China produced more than 13.60 million tons of copper processing products,accounting for60%of the world’s total production.Since then,this proportion has expanded year by year,and will increase to about 66.7%in 2016.Meanwhile,China consumed nearly 11展开更多
As an important intermediate product, short-chain fatty acids(SCFAs) can be generated after hydrolysis and acidification from waste activated sludge, and then can be transformed to methane during anaerobic digestion...As an important intermediate product, short-chain fatty acids(SCFAs) can be generated after hydrolysis and acidification from waste activated sludge, and then can be transformed to methane during anaerobic digestion process. In order to obtain more SCFA and methane,most studies in literatures were centered on enhancing the hydrolysis of sludge anaerobic digestion which was proved as un-efficient. Though the alkaline pretreatment in our previous study increased both the hydrolysis and acidification processes, it had a vast chemical cost which was considered uneconomical. In this paper, a low energy consumption pretreatment method, i.e. enhanced the whole three stages of the anaerobic fermentation processes at the same time, was reported, by which hydrolysis and acidification were both enhanced, and the SCFA and methane generation can be significantly improved with a small quantity of chemical input. Firstly, the effect of different pretreated temperatures and pretreatment time on sludge hydrolyzation was compared. It was found that sludge pretreated at 100°C for 60 min can achieve the maximal hydrolyzation. Further, effects of different initial p Hs on acidification of the thermal pretreated sludge were investigated and the highest SCFA was observed at initial p H 9.0with fermentation time of 6 d, the production of which was 348.63 mg COD/g VSS(6.8 times higher than the blank test) and the acetic acid was dominant acid. Then, the mechanisms for this new pretreatment significantly improving SCFA production were discussed. Finally,the effect of this low energy consumption pretreatment on methane generation was investigated.展开更多
To promote sustainability, it has become increasingly vital to properly account material and energy flows in industrial production processes. Therefore, a generic process-level input-output (IO) model was developed ...To promote sustainability, it has become increasingly vital to properly account material and energy flows in industrial production processes. Therefore, a generic process-level input-output (IO) model was developed to provide an integrated energy (material) accounting and analysis approach for industrial production processes. By extending the existing processlevel IO models, the production, usage, export and loss of by-products were explicitly considered in the proposed IO model. Moreover, the by-products allocation procedures were incorporated into the proposed IO model to reflect individual contributions of products to energy consumption. Finally, the proposed model enabled calculating embodied energy of main products and total energy consumption under hierarchical accounting scope. Plant managers, energy management consultants, governmental officials and academic researchers could use this input-output model to account material and energy flows, thus calculating energy consumption indicators of a production process with their specific system boundary requirements. The accounting results could be further used for energy labeling, identifying bottlenecks of production activities, evaluating industrial symbiosis effects, improving materials and energy utilization efficiency, etc. The model could also be used as a planning tool to determine the effect that a particular change of technology and supply chains may have on the industrial production processes. The proposed model was tested and applied in a real integrated steel mill, which also provided the reference results for related researches. At last, some concepts, computational issues and limi- tations of the proposed model were discussed.展开更多
文摘China is the world’s largest producer of copper processing products as well as the world’s largest copper consumer market.In 2013,China produced more than 13.60 million tons of copper processing products,accounting for60%of the world’s total production.Since then,this proportion has expanded year by year,and will increase to about 66.7%in 2016.Meanwhile,China consumed nearly 11
基金supported by the National Science Foundation of China (Grant no. 51408419)the National Key Technology Research and Development Program of China (Grant nos. 2014BAL02B02-03 and 2014BAC29B01)the Key Program for International S&T Cooperation Projects of China (Grant no. 2012DFG91380)
文摘As an important intermediate product, short-chain fatty acids(SCFAs) can be generated after hydrolysis and acidification from waste activated sludge, and then can be transformed to methane during anaerobic digestion process. In order to obtain more SCFA and methane,most studies in literatures were centered on enhancing the hydrolysis of sludge anaerobic digestion which was proved as un-efficient. Though the alkaline pretreatment in our previous study increased both the hydrolysis and acidification processes, it had a vast chemical cost which was considered uneconomical. In this paper, a low energy consumption pretreatment method, i.e. enhanced the whole three stages of the anaerobic fermentation processes at the same time, was reported, by which hydrolysis and acidification were both enhanced, and the SCFA and methane generation can be significantly improved with a small quantity of chemical input. Firstly, the effect of different pretreated temperatures and pretreatment time on sludge hydrolyzation was compared. It was found that sludge pretreated at 100°C for 60 min can achieve the maximal hydrolyzation. Further, effects of different initial p Hs on acidification of the thermal pretreated sludge were investigated and the highest SCFA was observed at initial p H 9.0with fermentation time of 6 d, the production of which was 348.63 mg COD/g VSS(6.8 times higher than the blank test) and the acetic acid was dominant acid. Then, the mechanisms for this new pretreatment significantly improving SCFA production were discussed. Finally,the effect of this low energy consumption pretreatment on methane generation was investigated.
文摘To promote sustainability, it has become increasingly vital to properly account material and energy flows in industrial production processes. Therefore, a generic process-level input-output (IO) model was developed to provide an integrated energy (material) accounting and analysis approach for industrial production processes. By extending the existing processlevel IO models, the production, usage, export and loss of by-products were explicitly considered in the proposed IO model. Moreover, the by-products allocation procedures were incorporated into the proposed IO model to reflect individual contributions of products to energy consumption. Finally, the proposed model enabled calculating embodied energy of main products and total energy consumption under hierarchical accounting scope. Plant managers, energy management consultants, governmental officials and academic researchers could use this input-output model to account material and energy flows, thus calculating energy consumption indicators of a production process with their specific system boundary requirements. The accounting results could be further used for energy labeling, identifying bottlenecks of production activities, evaluating industrial symbiosis effects, improving materials and energy utilization efficiency, etc. The model could also be used as a planning tool to determine the effect that a particular change of technology and supply chains may have on the industrial production processes. The proposed model was tested and applied in a real integrated steel mill, which also provided the reference results for related researches. At last, some concepts, computational issues and limi- tations of the proposed model were discussed.