The load distribution and calculating formulae of the contact stresses in the rotor worm and stator helical surface for toroidal drive are given. The effecting factors on contact stresses and their effects are analyze...The load distribution and calculating formulae of the contact stresses in the rotor worm and stator helical surface for toroidal drive are given. The effecting factors on contact stresses and their effects are analyzed. The results is useful for reference purposes in manufacture and design of the drive.展开更多
Based on the mathematical model of a novel cosine gear drive, a few characteristics, such as the contact ratio, the sliding coefficient, and the contact and bending stresses, of this drive are analyzed. A comparison s...Based on the mathematical model of a novel cosine gear drive, a few characteristics, such as the contact ratio, the sliding coefficient, and the contact and bending stresses, of this drive are analyzed. A comparison study of these characteristics with the involute gear drive is also carried out. The influences of design parameters including the number of teeth and the pressure angle on the contact and bending stresses are studied. The following conclusions are achieved： the contact ratio of the cosine gear drive is about 1.2 to 1.3, which is reduced by about 20% in comparison with that of the involute gear drive. The sliding coefficient of the cosine gear drive is smaller than that of the involute gear drive. The contact and bending stresses of the cosine gear drive are lower than those of the involute gear drive. The contact and bending stresses decrease with the growth of the number of teeth and the pressure angle.展开更多
A direct digital design method （DDDM） of worm-gear drive is proposed. It is directly based on the simulation of manufacturing process and completely different from the conventional modeling method. The loaded tooth ...A direct digital design method （DDDM） of worm-gear drive is proposed. It is directly based on the simulation of manufacturing process and completely different from the conventional modeling method. The loaded tooth contact analysis （LTCA） method is analyzed, in which the advanced surface to surface searching technique is included. The influence of misalignment errors and contact deformations on contact zone and transmission error （TE） is discussed. Combined modification approach on worm tooth surface is presented. By means of DDDM and LTCA, it is very conven- ient to verify the effect of worm-gear drive＇s modification approach. The analysis results show that, the modification in profile direction reduces the sensitivity of worm-gear drive to misalignment errors and the modification in longitudinal direction decreases the TE. Thus the optimization design of worm-gear drive can be achieved prior to the actual manufacturing process.展开更多
文摘The load distribution and calculating formulae of the contact stresses in the rotor worm and stator helical surface for toroidal drive are given. The effecting factors on contact stresses and their effects are analyzed. The results is useful for reference purposes in manufacture and design of the drive.
基金National Natural Science Foundation of China(No.50575071)Natural Science Foundation of Hunan Province,China(No.06JJl0008)+1 种基金S&T Programs of Hunan Province,China(No.2007FJ4047)Program for New Century Excellent Talents in University,China.
文摘Based on the mathematical model of a novel cosine gear drive, a few characteristics, such as the contact ratio, the sliding coefficient, and the contact and bending stresses, of this drive are analyzed. A comparison study of these characteristics with the involute gear drive is also carried out. The influences of design parameters including the number of teeth and the pressure angle on the contact and bending stresses are studied. The following conclusions are achieved： the contact ratio of the cosine gear drive is about 1.2 to 1.3, which is reduced by about 20% in comparison with that of the involute gear drive. The sliding coefficient of the cosine gear drive is smaller than that of the involute gear drive. The contact and bending stresses of the cosine gear drive are lower than those of the involute gear drive. The contact and bending stresses decrease with the growth of the number of teeth and the pressure angle.
基金This project is supported by National Natural Science Foundation of China (No.E50575234).
文摘A direct digital design method （DDDM） of worm-gear drive is proposed. It is directly based on the simulation of manufacturing process and completely different from the conventional modeling method. The loaded tooth contact analysis （LTCA） method is analyzed, in which the advanced surface to surface searching technique is included. The influence of misalignment errors and contact deformations on contact zone and transmission error （TE） is discussed. Combined modification approach on worm tooth surface is presented. By means of DDDM and LTCA, it is very conven- ient to verify the effect of worm-gear drive＇s modification approach. The analysis results show that, the modification in profile direction reduces the sensitivity of worm-gear drive to misalignment errors and the modification in longitudinal direction decreases the TE. Thus the optimization design of worm-gear drive can be achieved prior to the actual manufacturing process.
