Existing studies primarily focus on stiffness and damping under full-film lubrication or dry contact conditions.However,most lubricated transmission components operate in the mixed lubrication region,indicating that b...Existing studies primarily focus on stiffness and damping under full-film lubrication or dry contact conditions.However,most lubricated transmission components operate in the mixed lubrication region,indicating that both the asperity contact and film lubrication exist on the rubbing surfaces.Herein,a novel method is proposed to evaluate the time-varying contact stiffness and damping of spiral bevel gears under transient mixed lubrication conditions.This method is sufficiently robust for addressing any mixed lubrication state regardless of the severity of the asperity contact.Based on this method,the transient mixed contact stiffness and damping of spiral bevel gears are investigated systematically.The results show a significant difference between the transient mixed contact stiffness and damping and the results from Hertz(dry)contact.In addition,the roughness significantly changes the contact stiffness and damping,indicating the importance of film lubrication and asperity contact.The transient mixed contact stiffness and damping change significantly along the meshing path from an engaging-in to an engaging-out point,and both of them are affected by the applied torque and rotational speed.In addition,the middle contact path is recommended because of its comprehensive high stiffness and damping,which maintained the stability of spiral bevel gear transmission.展开更多
A new expression for contact deformation is given, and the normal contact stiff- ness between single asperities is derived according to Hooke's law. A contact model between two ellipsoidal asperities is simulated by ...A new expression for contact deformation is given, and the normal contact stiff- ness between single asperities is derived according to Hooke's law. A contact model between two ellipsoidal asperities is simulated by the FE method, the result compared with the theoretical solution. It is found that the curves of the normal contact stiffness versus the included angle in the principal curvature direction show similar trends and evolve as a cosine feature. The effects of the parameters on normal contact stiffness are found to show that normal contact stiffness increases and reaches the upper limit gradually with an increase in these parameters.展开更多
The contact stiffness of the joint surface directly affects the static and dynamic mechanical behavior,and accuracy of the machine tool.A new elastoplastic contact stiffness model is proposed by considering continuous...The contact stiffness of the joint surface directly affects the static and dynamic mechanical behavior,and accuracy of the machine tool.A new elastoplastic contact stiffness model is proposed by considering continuous and smooth contact characteristics and substrate deformation.First,the interpolation interval of cubic Hermite polynomials is improved to meet the continuous and smooth change of contact parameters during asperity deformation.Then,the micro-contact mechanism considering substrate deformation is explored by establishing an asperity-substrate system model.Furthermore,combined with statistical principles,a new contact stiffness model of the joint surface is established.Finally,the correctness of the built model is verified by comparing with experimental data and different contact models.The simulation results show that the model changes continuously and smoothly in the three deformation regions.The substrate deformation mainly affects the asperities in the elastic contact stage.The smoother is the surface,the more significant is the influence of substrate deformation.展开更多
Elastohydrodynamic lubrication(EHL)point contact occurs between two rough surfaces at the mesoscopic level,while the interaction of rough surfaces involves contact between asperities at the microscale level.In most ca...Elastohydrodynamic lubrication(EHL)point contact occurs between two rough surfaces at the mesoscopic level,while the interaction of rough surfaces involves contact between asperities at the microscale level.In most cases,the contact between asperities within an interface takes the form of lateral contact rather than peak contact.Regions devoid of contact asperities are filled with lubricating oil.However,conventional models often oversimplify lateral contact forms as interactions between asperities and a smooth,rigid plane.These simplifications fail to accurately represent the true contact conditions and can lead to inaccuracies in the analysis of EHL’s contact performance.To address this issue,we have developed a novel EHL interface model comprising two rough surfaces.This model allows us to explore the influence of asperity height,contact angle,and contact azimuth angle on EHL interface performance.展开更多
An industrial robot with a six-axis force/torque sensor is usually used to produce a zero-gravity environment for testing space robotic operations.However,using traditional force control methods,such as admittance con...An industrial robot with a six-axis force/torque sensor is usually used to produce a zero-gravity environment for testing space robotic operations.However,using traditional force control methods,such as admittance control,causes position-controlled industrial robots to undergo from force divergence owing to intrinsic time delay.In this paper,a new force control method is proposed to eliminate the force divergence.A hardware-in-the-loop(HIL)simulator with an industrial robot is first presented.The free-floating satellite dynamics and the motion mapping from the satellites to simulator are both established.Thus,the effects of measurement delay and dynamic response delay on contact velocity and force are investigated.After that,a real-time estimation method for contact stiffness and damping is proposed based on the adaptive Kalman filter.The measurement delay is compensated by a phase lead model.Moreover,the identified contact parameters are adopted to modify contact forces,and thus the dynamics response delay can be compensated for.Finally,a co-simulation and experiments were conducted to verify the force control method.The results show that contact stiffness and damping could be identified exactly and that the simulation divergence could be prevented.This paper proposes an active compliance control method that can deal with force constrained tasks of a position-controlled robot in unknown environments.展开更多
Traditional technique such nanoindenter(NI) can't measure the local elastic modulus at nano-scale(lateral). Atomic force acoustic microscopy (AFAM) is a dynamic method, which can quantitatively determine indent...Traditional technique such nanoindenter(NI) can't measure the local elastic modulus at nano-scale(lateral). Atomic force acoustic microscopy (AFAM) is a dynamic method, which can quantitatively determine indentation modulus by measuring the contact resonance spectra for high order modes of the cantilever. But there are few reports on the effect of experimental factors, such length of cantilever, contact stiffness on measured value. For three different samples, including copper(Cu) film with 110 nm thickness, zinc(Zn) film of 90 nm thickness and glass slides, are prepared and tested, using referencing approach in which measurements are performed on the test and reference samples (it's elastic modulus is known), and their contact resonance spectra are measured used the AFAM system experimentally. According to the vibration theory, from the lowest two contact resonance frequencies, the tip-sample contact stiffness is calculated, and then the values for the elastic properties of test sample, such as the indentation modulus, are determined. Using AFAM system, the measured indentation modulus of copper nano-film, zinc nano-film and glass slides are 113.53 GPa, 87.92 GPa and 57.04 GPa, which are agreement with literature values Mcu--105-130 GPa, Mzn = 88.44 GPa and Molass = 50-90 GPa. Furthermore, the sensitivity of contact resonance frequency to contact stiffness is analyzed theoretically. The results show that for the cantilevers with the length 160 pm, 225 μm and 520 μm respectively, when contact stiffness increases from 400 N/m to 600 N/m, the increments of first contact resonance frequency are 126 kHz, 93 kHz and 0.6 kHz, which show that the sensitivity of the contact resonance frequency to the contact stiffness reduces with the length of cantilever increasing. The novel method presented can characterize elastic modulus of near surface for nano-film and bulk material, and local elasticity of near surface can be evaluated by optimizing the experimental parameters using the AFAM system.展开更多
The elastic loading behaviour of rough surfaces is derived based on the physical understanding of the contact phenomena, where the pressure distribution is analytically obtained without any negative values or converge...The elastic loading behaviour of rough surfaces is derived based on the physical understanding of the contact phenomena, where the pressure distribution is analytically obtained without any negative values or convergence problems, thus the evolution of the contact behaviour is obtained in a semi-analytical manner. Numerical results obtained by the proposed approach facilitate the understanding of the contact behaviour in the following aspects: 1) the ratio of contact area to load decreases with an increase in real contact area;2) normal approach-load relationship is approximated by an exponential decay under relatively small loads and a linear decay under relatively large loads;and 3) average gap shows an exponential relationship with load only in moderate load range.展开更多
In situ changes in the nanofriction and microstructures of ionic liquids(ILs)on uncharged and charged surfaces have been investigated using colloid probe atomic force microscopy(AFM)and molecular dynamic(MD)simulation...In situ changes in the nanofriction and microstructures of ionic liquids(ILs)on uncharged and charged surfaces have been investigated using colloid probe atomic force microscopy(AFM)and molecular dynamic(MD)simulations.Two representative ILs,[BMIM][BF_(4)](BB)and[BMIM][PF_(6)](BP),containing a common cation,were selected for this study.The torsional resonance frequency was captured simultaneously when the nanoscale friction force was measured at a specified normal load;and it was regarded as a measure of the contact stiffness,reflecting in situ changes in the IL microstructures.A higher nanoscale friction force was observed on uncharged mica and highly oriented pyrolytic graphite(HOPG)surfaces when the normal load increased;additionally,a higher torsional resonance frequency was detected,revealing a higher contact stiffness and a more ordered IL layer.The nanofriction of ILs increased at charged HOPG surfaces as the bias voltage varied from 0 to 8 V or from 0 to−8 V.The simultaneously recorded torsional resonance frequency in the ILs increased with the positive or negative bias voltage,implying a stiffer IL layer and possibly more ordered ILs under these conditions.MD simulation reveals that the[BMIM]+imidazolium ring lies parallel to the uncharged surfaces preferentially,resulting in a compact and ordered IL layer.This parallel“sleeping”structure is more pronounced with the surface charging of either sign,indicating more ordered ILs,thereby substantiating the AFM-detected stiffer IL layering on the charged surfaces.Our in situ observations of the changes in nanofriction and microstructures near the uncharged and charged surfaces may facilitate the development of IL-based applications,such as lubrication and electrochemical energy storage devices,including supercapacitors and batteries.展开更多
基金This research was supported by the National Natural Science Foundation of China(NSFC,No.51875369)by the Chongqing Key Industry General Key Technology Innovation Special Major R&D Projects(No.cstc2017zdcy-zdzxX0001)Wei Pu would also like to thank the Fundamental Research Funds for the Central Universities(No.YJ201752)。
文摘Existing studies primarily focus on stiffness and damping under full-film lubrication or dry contact conditions.However,most lubricated transmission components operate in the mixed lubrication region,indicating that both the asperity contact and film lubrication exist on the rubbing surfaces.Herein,a novel method is proposed to evaluate the time-varying contact stiffness and damping of spiral bevel gears under transient mixed lubrication conditions.This method is sufficiently robust for addressing any mixed lubrication state regardless of the severity of the asperity contact.Based on this method,the transient mixed contact stiffness and damping of spiral bevel gears are investigated systematically.The results show a significant difference between the transient mixed contact stiffness and damping and the results from Hertz(dry)contact.In addition,the roughness significantly changes the contact stiffness and damping,indicating the importance of film lubrication and asperity contact.The transient mixed contact stiffness and damping change significantly along the meshing path from an engaging-in to an engaging-out point,and both of them are affected by the applied torque and rotational speed.In addition,the middle contact path is recommended because of its comprehensive high stiffness and damping,which maintained the stability of spiral bevel gear transmission.
基金Project supported by the National Basic Research Program of China(973 Program)(No.2009CB724406)
文摘A new expression for contact deformation is given, and the normal contact stiff- ness between single asperities is derived according to Hooke's law. A contact model between two ellipsoidal asperities is simulated by the FE method, the result compared with the theoretical solution. It is found that the curves of the normal contact stiffness versus the included angle in the principal curvature direction show similar trends and evolve as a cosine feature. The effects of the parameters on normal contact stiffness are found to show that normal contact stiffness increases and reaches the upper limit gradually with an increase in these parameters.
基金This work was supported by the National Natural Science Foundation of China(Grant Number 51975449)the Key Research and Development Program of Shaanxi(Number 2021GY-309)。
文摘The contact stiffness of the joint surface directly affects the static and dynamic mechanical behavior,and accuracy of the machine tool.A new elastoplastic contact stiffness model is proposed by considering continuous and smooth contact characteristics and substrate deformation.First,the interpolation interval of cubic Hermite polynomials is improved to meet the continuous and smooth change of contact parameters during asperity deformation.Then,the micro-contact mechanism considering substrate deformation is explored by establishing an asperity-substrate system model.Furthermore,combined with statistical principles,a new contact stiffness model of the joint surface is established.Finally,the correctness of the built model is verified by comparing with experimental data and different contact models.The simulation results show that the model changes continuously and smoothly in the three deformation regions.The substrate deformation mainly affects the asperities in the elastic contact stage.The smoother is the surface,the more significant is the influence of substrate deformation.
基金supported by the National Natural Science Foundation of China(No.52005401,No.52375127)the Cultivation Scientific Research Project of Panzhihua University(2021PY001)+1 种基金the Opening Project of Material Corrosion and Protection Key Laboratory of Sichuan province(2022CL15)the Project for Science and Technology Plan of Henan Province(212102210445).
文摘Elastohydrodynamic lubrication(EHL)point contact occurs between two rough surfaces at the mesoscopic level,while the interaction of rough surfaces involves contact between asperities at the microscale level.In most cases,the contact between asperities within an interface takes the form of lateral contact rather than peak contact.Regions devoid of contact asperities are filled with lubricating oil.However,conventional models often oversimplify lateral contact forms as interactions between asperities and a smooth,rigid plane.These simplifications fail to accurately represent the true contact conditions and can lead to inaccuracies in the analysis of EHL’s contact performance.To address this issue,we have developed a novel EHL interface model comprising two rough surfaces.This model allows us to explore the influence of asperity height,contact angle,and contact azimuth angle on EHL interface performance.
基金National Natural Science Foundation of China(Grant No.52175022)State Key Laboratory of Mechanical System and Vibration of China(Grant No.MSVZD2021-06)Shanghai R&D Public Service Platform Project of China(Grant No.19DZ2291400).
文摘An industrial robot with a six-axis force/torque sensor is usually used to produce a zero-gravity environment for testing space robotic operations.However,using traditional force control methods,such as admittance control,causes position-controlled industrial robots to undergo from force divergence owing to intrinsic time delay.In this paper,a new force control method is proposed to eliminate the force divergence.A hardware-in-the-loop(HIL)simulator with an industrial robot is first presented.The free-floating satellite dynamics and the motion mapping from the satellites to simulator are both established.Thus,the effects of measurement delay and dynamic response delay on contact velocity and force are investigated.After that,a real-time estimation method for contact stiffness and damping is proposed based on the adaptive Kalman filter.The measurement delay is compensated by a phase lead model.Moreover,the identified contact parameters are adopted to modify contact forces,and thus the dynamics response delay can be compensated for.Finally,a co-simulation and experiments were conducted to verify the force control method.The results show that contact stiffness and damping could be identified exactly and that the simulation divergence could be prevented.This paper proposes an active compliance control method that can deal with force constrained tasks of a position-controlled robot in unknown environments.
基金supported by National Natural Science Foundation of China(Grant No. 50775005)General Program of Science and Technology Development Project of Beijing Municipal Education Commission(Grant No. KM201110015009)
文摘Traditional technique such nanoindenter(NI) can't measure the local elastic modulus at nano-scale(lateral). Atomic force acoustic microscopy (AFAM) is a dynamic method, which can quantitatively determine indentation modulus by measuring the contact resonance spectra for high order modes of the cantilever. But there are few reports on the effect of experimental factors, such length of cantilever, contact stiffness on measured value. For three different samples, including copper(Cu) film with 110 nm thickness, zinc(Zn) film of 90 nm thickness and glass slides, are prepared and tested, using referencing approach in which measurements are performed on the test and reference samples (it's elastic modulus is known), and their contact resonance spectra are measured used the AFAM system experimentally. According to the vibration theory, from the lowest two contact resonance frequencies, the tip-sample contact stiffness is calculated, and then the values for the elastic properties of test sample, such as the indentation modulus, are determined. Using AFAM system, the measured indentation modulus of copper nano-film, zinc nano-film and glass slides are 113.53 GPa, 87.92 GPa and 57.04 GPa, which are agreement with literature values Mcu--105-130 GPa, Mzn = 88.44 GPa and Molass = 50-90 GPa. Furthermore, the sensitivity of contact resonance frequency to contact stiffness is analyzed theoretically. The results show that for the cantilevers with the length 160 pm, 225 μm and 520 μm respectively, when contact stiffness increases from 400 N/m to 600 N/m, the increments of first contact resonance frequency are 126 kHz, 93 kHz and 0.6 kHz, which show that the sensitivity of the contact resonance frequency to the contact stiffness reduces with the length of cantilever increasing. The novel method presented can characterize elastic modulus of near surface for nano-film and bulk material, and local elasticity of near surface can be evaluated by optimizing the experimental parameters using the AFAM system.
基金The authors acknowledge the financial supports by the National Key Research and Development Program of China(2016YFF0204305)the National Natural Science Foundation of China(51775460 and 51905456)the China Postdoctoral Science Foundation(2019M653836XB).
文摘The elastic loading behaviour of rough surfaces is derived based on the physical understanding of the contact phenomena, where the pressure distribution is analytically obtained without any negative values or convergence problems, thus the evolution of the contact behaviour is obtained in a semi-analytical manner. Numerical results obtained by the proposed approach facilitate the understanding of the contact behaviour in the following aspects: 1) the ratio of contact area to load decreases with an increase in real contact area;2) normal approach-load relationship is approximated by an exponential decay under relatively small loads and a linear decay under relatively large loads;and 3) average gap shows an exponential relationship with load only in moderate load range.
基金This work was supported by the Natural Science Foundation of Jiangsu Province(No.BK20191289)the National Natural Science Foundation of China(Nos.21838004,21978134,and 21676137)+2 种基金the National Key R&D Program of China(No.2018YFB0204403)the Swedish Research Council(No.2018-04133)the German Research Foundation,DFG(No.GN 92/16-1).
文摘In situ changes in the nanofriction and microstructures of ionic liquids(ILs)on uncharged and charged surfaces have been investigated using colloid probe atomic force microscopy(AFM)and molecular dynamic(MD)simulations.Two representative ILs,[BMIM][BF_(4)](BB)and[BMIM][PF_(6)](BP),containing a common cation,were selected for this study.The torsional resonance frequency was captured simultaneously when the nanoscale friction force was measured at a specified normal load;and it was regarded as a measure of the contact stiffness,reflecting in situ changes in the IL microstructures.A higher nanoscale friction force was observed on uncharged mica and highly oriented pyrolytic graphite(HOPG)surfaces when the normal load increased;additionally,a higher torsional resonance frequency was detected,revealing a higher contact stiffness and a more ordered IL layer.The nanofriction of ILs increased at charged HOPG surfaces as the bias voltage varied from 0 to 8 V or from 0 to−8 V.The simultaneously recorded torsional resonance frequency in the ILs increased with the positive or negative bias voltage,implying a stiffer IL layer and possibly more ordered ILs under these conditions.MD simulation reveals that the[BMIM]+imidazolium ring lies parallel to the uncharged surfaces preferentially,resulting in a compact and ordered IL layer.This parallel“sleeping”structure is more pronounced with the surface charging of either sign,indicating more ordered ILs,thereby substantiating the AFM-detected stiffer IL layering on the charged surfaces.Our in situ observations of the changes in nanofriction and microstructures near the uncharged and charged surfaces may facilitate the development of IL-based applications,such as lubrication and electrochemical energy storage devices,including supercapacitors and batteries.