A MIXED METHOD OF SOLUTION FOR CONTACT STRESSES ON ROLLER

A mixed method of solution for contact stresses on rollers was suggested by the combina- tion of similitude principle.photoelastic method,Hertz's contact theory and numerical calculation.Thus,not only the distribution regularity of axial contact pressure on roller of limited length,but also the three-dimensional solution of stresses in the contact po- sitions may be obtained.An actual example is presented in the paper.It shows that the practical damaged phenomenon in real roller is in agreement with the result of the analysis

Contact Stress Reliability Analysis Model for Cylindrical Gear with Circular Arc Tooth Trace Based on an Improved Metamodel

Although there is currently no unified standard theoretical formula for calculating the contact stress of cylindrical gears with a circular arc tooth trace(referred to as CATT gear),a mathematical model for determining the contact stress of CATT gear is essential for studying how parameters affect its contact stress and building the contact stress limit state equation for contact stress reliability analysis.In this study,a mathematical relationship between design parameters and contact stress is formulated using the KrigingMetamodel.To enhance the model’s accuracy,we propose a new hybrid algorithm that merges the genetic algorithm with the Quantum Particle Swarm optimization algorithm,leveraging the strengths of each.Additionally,the“parental inheritance+self-learning”optimization model is used to fine-tune the KrigingMetamodel’s parameters.Following this,amathematicalmodel for calculating the contact stress of Variable Hyperbolic Circular-Arc-Tooth-Trace(VH-CATT)gears using the optimized Kriging model was developed.We then examined how different gear parameters affect the VH-CATT gears’contact stress.Our simulation results show:(1)Improvements in R2,RMSE,and RMAE.R2 rose from0.9852 to 0.9974(a 1.22%increase),nearing 1,suggesting the optimized Kriging Metamodel’s global error is minimized.Meanwhile,RMSE dropped from3.9210 to 1.6492,a decline of 57.94%.The global error of the GA-IQPSO-Kriging algorithm was also reduced,with RMAE decreasing by 58.69%from 0.1823 to 0.0753,showing the algorithm’s enhanced precision.In a comparison of ten experimental groups selected randomly,the GA-IQPSO-Kriging and FEM-based contact analysis methods were used to measure contact stress.Results revealed a maximum error of 12.11667 MPA,which represents 2.85%of the real value.(2)Several factors,including the pressure angle,tooth width,modulus,and tooth line radius,are inversely related to contact stress.The descending order of their impact on the contact stress is:tooth line radius>modulus>pressure angle>tooth width.(3)Complex interactions are noted among various parameters.Specifically,when the tooth line radius interacts with parameters such as pressure angle,tooth width,and modulus,the resulting stress contour is nonlinear,showcasing amultifaceted contour plane.However,when tooth width,modulus,and pressure angle interact,the stress contour is nearly linear,and the contour plane is simpler,indicating a weaker coupling among these factors.

STUDY ON LOADS AND CONTACT STRESSES FOR TOROIDAL DRIVE

The load distribution and calculating formulae of the contact stresses in the rotor worm and stator helical surface for toroidal drive are given. The effecting factors on contact stresses and their effects are analyzed. The results is useful for reference purposes in manufacture and design of the drive.

Contact Mechanism of Rail Grinding with Open-Structured Abrasive Belt Based on Pressure Grinding Plate

The current research of abrasive belt grinding rail mainly focuses on the contact mechanism and structural design.Compared with the closed structure abrasive belt grinding,open-structured abrasive belt grinding has excellent performance in dynamic stability,consistency of grinding quality,extension of grinding mileage and improvement of working efficiency.However,in the contact structure design,the open-structured abrasive belt grinding rail using a profiling pressure grinding plate and the closed structure abrasive belt using the contact wheel are different,and the contact mechanisms of the two are different.In this paper,based on the conformal contact and Hertz theory,the contact mechanism of the pressure grinding plate,abrasive belt and rail is analyzed.Through finite element simulation and static pressure experiment,the contact behavior of pressure grinding plate,abrasive belt and rail under single concentrated force,uniform force and multiple concentrated force was studied,and the distribution characteristics of contact stress on rail surface were observed.The results show that under the same external load,there are three contact areas under the three loading modes.The outer contour of the middle contact area is rectangular,and the inner contour is elliptical.In the contact area at both ends,the stress is extremely small under a single concentrated force,the internal stress is drop-shaped under a uniform force,and the internal stress under multiple concentration forces is elliptical.Compared with the three,the maximum stress is the smallest and the stress distribution is more uniform under multiple concentrated forces.Therefore,the multiple concentrated forces is the best grinding pressure loading mode.The research provides support for the application of rail grinding with open-structured abrasive belt based on pressure grinding plate,such as contact mechanism and grinding pressure mode selection.

Interfacial friction effects on sealing performances of elastomer packer

Elastomer sealing performance is of critical importance for downhole tools application including the use of fracturing(Frac)plugs during multi-stage hydraulic fracking.In practice sealing performances of such plugs are normally evaluated through pressure tests,and in numerical simulation studies,maximum contact stress,average contact stress and contact length data are used to determine sealing quality between a packer and casing.In previous studies,the impact of friction forces on sealing performance is often overlooked.This work aims to fill this knowledge gap in determining the influence of friction forces on elastomer packer sealing performances.We first determined the most appropriate constitutive hyperelastic model for the elastomers used in frac plug.Then we compared analytical calculation results with Finite Element Analysis simulation using a simplified tubular geometry and showed the significant influences on interfacial friction on elastomer packer stress distribution,deformation,and contact stress after setting.With the demonstration of validity of FEA method,we conducted systematic numerical simulation studies to show how the interfacial friction coefficients can affect the maximum contact stress,average contact stress,contact stress distribution,and maximum mises stress for an actual packer used in plug products.In addition,we also demonstrated how the groove in a packer can affect packer deformation and evolvement during setting with the consideration of interfacial stress.This study underscores the critical role that friction forces play in Frac plug performance and provides a new dimension for optimizing packer design by controlling interfacial interactions at the packer contact surfaces.

Study on Sealing Characteristics of Sliding Seal Assembly of Aircraft Hydraulic Actuator

The hydraulic actuator,known as the"muscle"of military aircraft,is responsible for flight attitude adjustment,trajectory control,braking turn,landing gear retracting and other actions,which directly affect its flight efficiency and safety.However,the sealing assembly often has the situation of over-aberrant aperture fit clearance or critical over-aberrant clearance,which increases the failure probability and degree of movable seal failure,and directly affects the flight efficiency and safety of military aircraft.In this paper,the simulation model of hydraulic actuator seal combination is established by ANSYS software,and the sealing principle is described.The change curve of contact width and contact pressure of combination seal under the action of high-pressure fluid is drawn.The effects of different oil pressure,fit clearance and other parameters on the sealing performance are analyzed.Finally,the accelerated life test of sliding seal components is carried out on the hydraulic actuator accelerated life test rig,and the surface morphology is compared and analyzed.The research shows that the O-ring is the main sealing element and the role of the check ring is to protect and support the O-ring to prevent damage caused by squeezing into the fit clearance,so the check ring bears a large load and is prone to shear failure.Excessive fit clearance is the main factor affecting the damage of the check ring,and the damage parts are mainly concentrated at the edge of the sealing surface.This paper provides a theoretical basis for the design of hydraulic actuator and the improvement of sealing performance.

Analysis and Numerical Simulation of Rolling Contact between Sphere and Cone

In non-conforming rolling contact, the contact stress is highly concentrated in the contact area. However, there are some limitations of the special contact model and stress model used for the theoretical study of the phenomenon, and this has prevented in-depth analysis of the associated friction, wear, and failure. This paper is particularly aimed at investigating the area of rolling contact between a sphere and a cone, for which purpose the boundary is determined by the Hertz theory and the geometries of the non-conforming surfaces. The phenomenon of stick-slip contact is observed to occur in the contact area under the condition of no-full-slip（Q 〈 μ·P）. Using the two-dimensional rolling contact theory developed by CARTER, the relative positions of the stick and slip regions and the distribution of the tangential force over the contact area are analyzed. Furthermore, each stress component is calculated based on the Mc Ewen theory and the idea of narrow band. The stress equations for the three-dimensional rolling contact between the sphere and the cone are obtained by the principle of superposition, and are used to perform some numerical simulations. The results show that the stress components have a large gradient along the boundary between the stick and slip regions, and that the maximum stress is inversely proportional to the contact coefficient and proportional to the friction coefficient. A new method for investigating the stress during non-classical three-dimensional rolling contact is proposed as a theoretical foundation for the analysis of the associated friction, wear, and failure.

Effects of Service Condition on Rolling Contact Fatigue Failure Mechanism and Lifetime of Thermal Spray Coatings——A Review

The service condition determines the Roiling Contact Fatigue（RCF） failure mechanism and lifetime under ascertain material structure integrity parameter of thermal spray coating. The available literature on the RCF testing of thermal spray coatings under various condition services is considerable; it is generally difficult to synthesize all of the result to obtain a comprehensive understanding of the parameters which has a great effect on a thermal spray coating＇s resistance of RCF. The effects of service conditions（lubrication states, contact stresses, revolve speed, and slip ratio） on the changing of thermal spray coatings＇ contact fatigue lifetime is introduced systematically. The effects of different service condition on RCF failure mechanism of thermal spray coating from the change of material structure integrity are also summarized. Moreover, In order to enhance the RCF performance, the parameter optimal design formula of service condition and material structure integrity is proposed based on the effect of service condition on thermal spray coatings＇ contact fatigue lifetime and RCF failure mechanism. The shortage of available literature and the forecast focus in future researches are discussed based on available research. The explicit result of RCF lifetime law and parameter optimal design formula in term of lubrication states, contact stresses, revolve speed, and slip ratio, is significant to improve the RCF performance on the engineering application.

Loaded multi-tooth contact analysis and calculation for contact stress of face-gear drive with spur involute pinion

The analytical method based on "Hertz theory on normal contact of elastic solids" and the numerical method based on finite element method (FEM) calculating the contact stress of face-gear drive with spur involute pinion were introduced, and their relative errors are below 10%, except edge contact, which turns out that these two methods can compute contact stress of face-gear drive correctly and effectively. An agreement of the localized bearing contact stress is gotten for these two methods, making sure that the calculation results of FEM are reliable. The loaded meshing simulations of multi-tooth FEM model were developed, and the determination of the transmission error and the maximal load distribution factor of face-gear drive under torques were given. A formula for the maximal load distribution factor was proposed. By introducing the maximal load distribution factor in multi-tooth contact zone, a method for calculating the maximal contact stress in multi-tooth contact can be given. Compared to FEM, the results of these formulae are proved to be reliable, and the relative errors are below 10%.

Contact Stress Distribution of a Pear Cam Profile with Roller Follower Mechanism

The problem of this paper is the high contact stress at the point of contact between the cam and the follower.A pear cam and roller follower mechanism were studied and analyzed for different position of the follower and different contact compression load.The objective of this paper is to study the effect of contact compression load on the contact stress distribution of the cam profile at the point of contact.Four different positions of the follower with the cam was considered(0°,90°,180°,and 270°).The theory of circular plate was applied to derive the analytic solution of the contact stress.The numerical simulation had been done using ANSYS Ver.19.2 package to determine the contact stress,while SolidWorks software was used to investigate follower displacement,velocity,and acceleration.Four distinct values of the compression contact load,such as 3.121 N,6.242 N,9.364 N,and 12.485 N,were used in the numerical simulation.In the experiment setup,a photo-elastic technique was carried out in the field of polarized light to exhibit the stress distribution on the cam specimen.The annealed PSM-4 backalate material was used in the experiment setup.The experimental value of contact stress was checked and verified analytically and numerically at the point of contact.The innovation in this paper the use of spring-damper system which reduce the value of contact stress at the point of contact.The contact stress was maximum 2.136 MPa when the follower located at 270°with the cam,while the contact stress was minimum 1.802 MPa when the follower located at 180°at compression load 12.485 N.

Modeling and application of thermal contact resistance of ball screws

Aiming at determining the thermal contact resistance of ball screws,a new analytical method combining the minimum excess principle with the MB fractal theory is proposed to estimate thermal contact resistance of ball screws considering microscopic fractal characteristics of contact surfaces.The minimum excess principle is employed for normal stress analysis.Moreover,the MB fractal theory is adopted for thermal contact resistance.The effectiveness of the proposed method is validated by self-designed experiment.The comparison between theoretical and experimental results demonstrates that thermal contact resistance of ball screws can be obtained by the proposed method.On this basis,effects of fractal parameters on thermal contact resistance of ball screws are discussed.Moreover,effects of the axial load on thermal contact resistance of ball screws are also analyzed.The conclusion can be drawn that the thermal contact resistance decreases along with the fractal dimension D increase and it increases along with the scale parameter G increase,and thermal contact resistance of ball screws is retained almost constant along with axial load increase before the preload of the right nut turns into zero in value.The application of the proposed method is also conducted and validated by the temperature measurement on a self-designed test bed.

Hybrid Method to Analyze Contact Stress Distribution on Dry Friction Interfaces

A hybrid method is established by combining photoelastic experiment and finite element analysis.The method is used to evaluate contact stress distribution on dry friction interfaces,such as the contact interfaces between shrouds of fan blades and turbine blades.The photoelastic stress frozen experiment method is used to decide the displacement boundary conditions of numerical calculation.Higher accuracy and efficiency of solving problems are improved by the method.Technical difficulty and high cost of experiment are also avoided by the method.Good agreement of the stress distribution by using the hybrid method and experiment is obtained.

Effect of flank angle and friction coefficient on contact stress of turbine rotor

In order to simulate the stress of turbine rotor in aeroengine, based on the ANSYS, the simplification model of the turbine rotor was built up. By applying the simplification model, the contact stress of turbine rotor was computed. The maximum contact stress appears at the chamfer below the flank, which agrees with experiment result. At the same time, the contact stress changing with the flank angle and friction coefficient was calculated, The results show that the contact stress in the flank increases slowly with the increase of flank angle; with the friction coefficient increasing, the contact stress in flank length decreases; the contact stress will not change when the friction coefficient is over 0.25.

CALCULATION OF CONTACT STRESS OF PLASTIC GEARS

A calculation method of contact problem of plastic gears based on three parameter model of viscoelasticity material is presented. In this calculation method, the influence of temperature upon the property of plastics is considered and an iteration process of temperature-elasticity module-friction coefficient is proposed. From the rolling contact problem of two viscoelastic cylinders with parallel axis, a set of normal-tangential contact coupled integral equations is obtained. Through numerical treatment and normal-tangential iteration, the normal contact stress,tangential stress and contact width of plastic gears are acquired.

Numerical analysis of elastic coated solids in line contact

A line contact model of elastic coated solids is presented based on the influence coefficients(ICs) of surface displacement and stresses of coating-substrate system and the traditional contact model. The ICs of displacement and stresses are obtained from their corresponding frequency response functions(FRF) by using a conversion method based on fast Fourier transformation(FFT). The contact pressure and the stress field in the subsurface are obtained by employing conjugate gradient method(CGM) and discrete convolution fast Fourier transformation(DC-FFT). Comparison of the contact pressure and subsurface stresses obtained by the numerical method with the exact analytical solutions for Hertz contact is conducted, and the results show that the numerical solution has a very high accuracy and verify the validity of the contact model. The effect of the stiffness and thickness of coatings is further numerically studied. The result shows that the effects on contact pressure and contact width are opposite for hard and soft coatings and are intensified with the increase of coating thickness; the locations of crack initiation and propagation are different for soft and hard coatings; the risk of cracks and delaminations of coatings can be brought down by improving the lubrication condition or optimizing the non-dimensional parameter h/bh. This research offers a tool to numerically analyze the problem of elastic coated solids in line contact and make the blindness and randomness of trial-type coating design less.

IMPROVED COHESIVE ZONE MODEL AND ITS APPLICATION IN INTERFACE CONTACT ANALYSIS

An improved interface cohesive zone model is developed for the simulation of interface contact, under mixed-mode loading. A new debonding initiation criterion and propagation of debonding law, taking into account the pressure stress influence on contact shear strength, is proposed. The model is implemented in a finite-element program using subroutine VUINTER of ABAQUS Explicit. An edge-notch four-point bending process and laminated vibration damping steel sheet punch forming test are simulated with the improved model in ABAQUS Explicit. The numerical predictions agree satisfactorily with the corresponding experimental results.

Effects of Temperature and Centrifugal Force on Fretting Wear of Contact Interface of Face Gear

Taking the typical face gear connection structure of the combined rotor as the research object,this paper studies the distribution rules of the contact state,contact stress and slip distance of the contact tooth surface of face gear under different centrifugal force and temperature conditions by using the finite element method,in order to improve the reliability of face gear connection structure.And the influence of centrifugal force and temperature on the maximum wear depth of the tooth surface is studied based on the fretting wear model proposed by McColl.Results show that:(1)The external diameter has an opening phenomenon on the contact surface of the face gear under the centrifugal effect,which reduces the load-bearing area;(2)The contact stress at the inner root of the face gear is the largest and the wear is the most serious;(3)The temperature field causes the contact surface to be thermally expanded,resulting in the large uneven deformation,and the tooth surface appears drum-shape;(4)The maximum contact stress and the maximum wear depth occur in the middle of the tooth root;(5)As the temperature increases,the maximum wear depth of the tooth surface increases significantly.Consequently,reducing temperature of the combined rotor plays an important role in effectively reducing the wear of the face gear and improving the connection life of face gear connection structure.

Calculating method of contact stress for non-circular gears

According to Hertz theory, the difference of contact stress for non-circular gears and equivalent gears is compared in the paper, a calculating method of contact stress for non-circular gears by using equivalent gears is researched, and computing formulas of power and rotation speed for equivalent gears are deduced. A numerical simulation of contact stress for non-circular gears has also been conducted based on the finite element method. By the comparison of fitting curves, the feasibility of using equivalent gears instead of non-circular gears to calculate the contact stress is testified.

Piezoelectric sensing method for segmental joint contact stress during shield tunnel construction

The emergence of curved shield tunnels poses a significant construction challenge.If the quality of the segment assembly is not guaranteed,many segment cracks and damage will result from the stress concentration.Sensing the contact stresses between segmental joints is necessary to improve the quality of segments assembled for shield tunnel construction.Polyvinylidene difluoride(PVDF)piezoelectric material was chosen for the sensor because it can convert contact stresses into electrical signals,allowing the state of the segmental joints to be effectively sensed.It matches the working environment between the segmental joints of the shield tunnel,where flexible structures such as rubber gaskets and force transfer pads are present.This study proposes a piezoelectric sensing method for segmental joints in shield tunnels and conducts laboratory tests,numerical analyses,and field tests to validate the feasibility of the method.The results indicate that the PVDF film sensor can effectively sense the entire compression process of the gasket with different amounts of compression.The piezoelectric cable sensor can effectively sense the joint offset direction of the gasket.For differently shaped sections,the variation in the force sensed by the piezoelectric cable sensors was different,as verified by numerical simulation.Through the field test,it was found that the average contact stress between the segmental joints was in the range of 1.2–1.8 MPa during construction of the curved shield tunnels.The location of the segmental joints and the type of segment affect the contact stress value.The field monitoring results show that piezoelectric sensing technology can be successfully applied during assembly of the segments for effective sensing of the contact stress.

Investigation into the analysis method for assessing contact stress in joint prosthesis

Contact stress is the important cause of wear and failure of knee joint prostheses implanted in the human body during movement.The calculation of contact stress on joint prostheses is often inaccurate due to the deviation of joint position during activity.This paper proposes a correction method for contact stress based on finite element results.Firstly,the contact stress and contact radius between femoral and tibial prostheses of knee joint were calculated and analyzed by Hertz contact theory.Then,individualized finite element models based on the individualized geometry of the joint prosthesis and individualized loading were constructed,and the finite element contact stress was analyzed.The finite element results were calibrated utilizing the Hertz contact theory.Additionally,this study investigated the impact of three gait patterns(normal gait,medial thrust gait,and bouncing gait)on the contact stress experienced by the tibial insert.The research methods and results can provide ideas for theoretical analysis and finite element simulation of prosthetic joint contact,as well as offer theoretical support and analysis methods for evaluating the lifespan of prosthetic joints.