In situ formation of an intimate solid-solid interface by reaction between MgH_(2) and Ti to stabilize metal hydride anode with high active material content

MgH_(2) and TiH_(2) have been extensively studied as potential anode materials due to their high theoretical specific capacities of 2036 and 1024 mAh/g,respectively.However,the large volume changes that these compounds undergo during cycling affects their performance and limits practical applications.The present work demonstrates a novel approach to limiting the volume changes of active materials.This effect is based on mechanical support from an intimate interface generated in situ via the reaction between MgH_(2) and Ti within the electrode prior to lithiation to form Mg and TiH_(2).The resulting Mg can be transformed back to MgH_(2) by reaction with LiH during delithiation.In addition,the TiH_(2) improves the reaction kinetics of MgH_(2) and enhances electrochemical performance.The intimate interface produced in this manner is found to improve the electrochemical properties of a MgH_(2)-Ti-LiH electrode.An exceptional reversible capacity of 800 mAh/g is observed even after 200 cycles with a high current density of 1 mA/cm^(2) and a high proportion of active material(90 wt.%)at an operation temperature of 120℃.This study therefore showcases a new means of improving the performance of electrodes by limiting the volume changes of active materials.

Study on Effectiveness of Solitary-Wave-Like Form Based on Overtopping Data from Irregular Wave Tests

The previous study conducted by Li(2022)demonstrates that the Goda graph can be adequately represented by a solitary-wave-like form across the entire range of relative water depth,with the exception of the extremely shallow zone.However,it remains uncertain whether this form is equally effective when applied to test data generated by irregular waves,as the Goda graph was initially developed based on overtopping data from regular wave tests.Additionally,it is unclear whether this form is suitable for formulating overtopping discharge at composite vertical walls.In order to address these questions,a 2D overtopping experiment was conducted,incorporating both simple and composite types of vertical walls,with various relative water depths across the entire range,excluding the extremely shallow zone.A novel analysis procedure was developed,which proved to be highly productive and can be considered a general method for data fitting.Ultimately,the study yielded two conclusions:(1)the solitary-wave-like form is remarkably effective in formulating overtopping test data generated by irregular waves,regardless of whether the vertical wall is simple or composite,and(2)the resulting formulas exhibit definitely better performance compared with existing formulas.

Projecting Wintertime Newly Formed Arctic Sea Ice through Weighting CMIP6 Model Performance and Independence

Precipitous Arctic sea-ice decline and the corresponding increase in Arctic open-water areas in summer months give more space for sea-ice growth in the subsequent cold seasons. Compared to the decline of the entire Arctic multiyear sea ice,changes in newly formed sea ice indicate more thermodynamic and dynamic information on Arctic atmosphere–ocean–ice interaction and northern mid–high latitude atmospheric teleconnections. Here, we use a large multimodel ensemble from phase 6 of the Coupled Model Intercomparison Project(CMIP6) to investigate future changes in wintertime newly formed Arctic sea ice. The commonly used model-democracy approach that gives equal weight to each model essentially assumes that all models are independent and equally plausible, which contradicts with the fact that there are large interdependencies in the ensemble and discrepancies in models' performances in reproducing observations. Therefore, instead of using the arithmetic mean of well-performing models or all available models for projections like in previous studies, we employ a newly developed model weighting scheme that weights all models in the ensemble with consideration of their performance and independence to provide more reliable projections. Model democracy leads to evident bias and large intermodel spread in CMIP6 projections of newly formed Arctic sea ice. However, we show that both the bias and the intermodel spread can be effectively reduced by the weighting scheme. Projections from the weighted models indicate that wintertime newly formed Arctic sea ice is likely to increase dramatically until the middle of this century regardless of the emissions scenario.Thereafter, it may decrease(or remain stable) if the Arctic warming crosses a threshold(or is extensively constrained).

Microstructure and forming mechanism of metals subjected to ultrasonic vibration plastic forming: A mini review

Compared with traditional plastic forming,ultrasonic vibration plastic forming has the advantages of reducing the forming force and improving the surface quality of the workpiece.This technology has a very broad application prospect in industrial manufactur-ing.Researchers have conducted extensive research on the ultrasonic vibration plastic forming of metals and laid a deep foundation for the development of this field.In this review,metals were classified according to their crystal structures.The effects of ultrasonic vibration on the microstructure of face-centered cubic,body-centered cubic,and hexagonal close-packed metals during plastic forming and the mech-anism underlying ultrasonic vibration forming were reviewed.The main challenges and future research direction of the ultrasonic vibra-tion plastic forming of metals were also discussed.

ELLIPTIC EQUATIONS IN DIVERGENCE FORM WITH DISCONTINUOUS COEFFICIENTS IN DOMAINS WITH CORNERS

We study equations in divergence form with piecewise Cαcoefficients.The domains contain corners and the discontinuity surfaces are attached to the edges of the corners.We obtain piecewise C^(1,α) estimates across the discontinuity surfaces and provide an example to illustrate the issue regarding the regularity at the corners.

Representation of an Integer by a Quadratic Form through the Cornacchia Algorithm

Cornachia’s algorithm can be adapted to the case of the equation x2+dy2=nand even to the case of ax2+bxy+cy2=n. For the sake of completeness, we have given modalities without proofs (the proof in the case of the equation x2+y2=n). Starting from a quadratic form with two variables f(x,y)=ax2+bxy+cy2and n an integer. We have shown that a primitive positive solution (u,v)of the equation f(x,y)=nis admissible if it is obtained in the following way: we take α modulo n such that f(α,1)≡0modn, u is the first of the remainders of Euclid’s algorithm associated with n and α that is less than 4cn/| D |) (possibly α itself) and the equation f(x,y)=n. has an integer solution u in y. At the end of our work, it also appears that the Cornacchia algorithm is good for the form n=ax2+bxy+cy2if all the primitive positive integer solutions of the equation f(x,y)=nare admissible, i.e. computable by the algorithmic process.

Assessment of the Drafting Quality of Request Forms Submitted to the Malaria and Parasitology Units at the Institut Pasteur de Cote d’Ivoire

Biological tests provide information on the medical analysis requested by both the patient and the prescriber. It is a communication link between the prescriber and the laboratory staff. The lack of some information on request forms not only affects the drafting quality of the test and patient care, but could also make thousands of data produced by healthcare centers unusable. The aim of this study was to assess the drafting quality of request forms submitted to the Malaria and Parasitology Units at the Institut Pasteur de Côte d’Ivoire. Methods: It was a descriptive cross-sectional study to assess the drafting quality of request forms of various prescribers received at the Institut Pasteur de Côte d’Ivoire. This study was conducted at the Malaria and Parasitology Units, department of Parasitology and Mycology (Institut Pasteur de Côte d’Ivoire), from 6th December 2020 to 6th December 2021. The information on each request forms was recorded on a data collection form designed for this purpose. Each data collection form corresponds to a request forms and each test to a patient. Results: Out of a total of 1990 request forms received, the patient’s age and sex were missing on 18% and 26.8% of the tests respectively. More than half (51.80%) of request forms did not indicate the patient’s place of residence. Clinical information was not provided on 45.90% of the tests. Prescribers omitting their signatures were 51%, stamps were 50.3% and contacts were 71.2%. Only 5.4% of request forms were of good drafting quality. Providing all the required information on the forms could facilitate the use and analysis of data and samples.

Bioaccumulation,subcellular distribution and chemical forms of cadmium in Aster subulatus Michx.

【Objective】Through analyzing the bioaccumulation capacity,subcellular distribution and chemical forms of cadmium(Cd)in Aster subulatus Michx.,this study was to provide reference for revealing the Cd tolerance mechanism of A.subulatus Michx.【Method】After cultured for 24 d under the action of Hoagland nutrient solution and gradient Cd concentrations(0,30,60 and 90 mg/L),A.subulatus Michx.were harvested,and its leaf,stem and root were treated by differential centrifugation,chemical reagent extraction,and digested with graphite digester,respectively,then the Cd content in the root,stem and leaf were determined by atomic absorption spectroscopy.【Result】The experimental results indicated that the bioaccumulation capacity of Cd in A.subulatus Michx.was root>stem>leaf,and the maximum Cd concentration in the root,stem and leaf of A.subulatus Michx.were 130.74,78.69 and 56.62 mg/kg(fresh matter),respectively.Most of Cd stored in the cell wall and the soluble fractions of the root and leaf of A.subulatus Michx.,with only a smaller portion Cd in organelle fraction.Analysis result of subcellular Cd content showed that 52.27%-58.61%of Cd for root was mainly stored in the soluble fraction,but 42.10%-63.28%of Cd for leaf was mainly stored in the cell wall fraction.The concentration of pectates and protein integrated-Cd was higher in the root and leaf compared to other chemical forms Cd.Pectates and protein integrated-Cd was the main chemical forms Cd in the root and leaf of A.subulatus Michx.,and their percentages were 68.91%-74.80%and 57.38%-83.80%,respectively.Cd treatment could significantly increase the proportion of water-soluble organic acid Cd from 13.64%to 22.72%in root and undissolved phosphate Cd from 10.02%to 32.78%in leaf with increasing Cd concentration in the culture medium.【Conclusion】The root,stem and leaf of A.subulatus Michx.has strong bioaccumulation capacity to Cd,Cd is primarily stored in the soluble fractions of the root and cell wall fractions of the leaf,and less toxic pectates and protein integrated-Cd is the main chemical forms Cd in the root and leaf of A.subulatus Michx.,this might be the main mechanism of Cd tolerance in A.subulatus Michx.

Familial Forms of Spondyloarthritis Study of 100 Senegalese Multiplex Families

Introduction: Spondyloarthritis (SpA) comprises a group of chronic inflammatory rheumatic diseases characterized by predominant axial involvement. These include ankylosing spondylitis (AS), reactive arthritis (ReA), psoriatic arthritis (PsA), arthritis associated with inflammatory bowel diseases (IBD), SAPHO syndrome (Synovitis, Acne, Pustulosis, Hyperostosis, and Osteitis), juvenile spondyloarthritis (JSPA), and undifferentiated SpA. Their exact cause is unknown but is believed to stem from a combination of factors. The first familial forms were described by de Blécourt et al. in 1961. The objective was to evaluate the epidemiological, clinical, therapeutic and evolutionary aspects of familial forms of SpA and in particular, to prove the severity of the disease in family members compared to index cases in the rheumatology department of the Aristide Le Dantec University Hospital in Dakar. Methodology: This was a prospective, cross-sectional and descriptive study with an analytical aim on patients with the familial form of spondyloarthritis defined by the existence of at least one other family member with SpA outside the propositus, collected within the Aristide Le Dantec rheumatology department in Dakar over a period of 10 years between January 2012 and December 2021. There were two phases of study, the first of which consisted of collecting index cases with miserly SpA and the second of which consisted of family screening after consent. The data analysed were epidemiological, clinical, paraclinical, therapeutic and evolving. Results: Out of 100 families of 1905 members, 667 SpA patients included, i.e. a prevalence of 35%, including 225 (33.73%) men and 412 women (61.17%), i.e. a ratio of 1.8. The mean age at diagnosis among relatives was 26.3 years (range 13 and 80 years), 47.14 years among the propositus, in whom the mean age at onset was 36.26 years and that of relatives 49.9 years in the first degree, 15 years in the second degree and 1 year in the third degree. The time to diagnosis was 11.20 years in the first degree, 2.5 years in the second degree, 1 year in the third degree and 10.88 years in the case of the proposes. The number of marriages in families was 420 of which 116 were consanguineous (consanguinity rate 27.62%), 19% among the propositus. HLA-B27 positive in 92% of the proposers and 33.43% in the families;70% of the propositus had an inflammatory syndrome and 17.54% in the families;87% of sacroilliitis in the propositus and 5.54% in the families. Clinical forms were dominated by undifferentiated SpA (338 cases) and APS (295 cases). The average BASFI was 3.23 on D0;2.59 in the 3rd month and 1 in the 6th month for the propositus versus 2.55 at D0;1.86 at the 3rd month and 1.55 in the 6th month in the families. Average BASDAI was 3.92 at D0;3.12 at the 3rd month and 2.07 at the 6th month in the propositus and 3 at D0;2.21 at the 3rd month and 1 at the 6th month in the families. Autoimmune associated conditions were 18 cases, degenerative 24 cases, autoinflammatory 2 metabolic cases 18 cases. They all received: NSAIDs, methotrexate, salazopyrine (11 cases) and anti-TNF-α (1 case). The evolution was generally favourable. Conclusion: SpA is on the rise in Senegalese hospitals, frequent in young people, SPA and undifferentiated SpA are the most frequent, management is essentially based on conventional care, and the disease is less severe in family members than index cases.

MPI/OpenMP-Based Parallel Solver for Imprint Forming Simulation

In this research,we present the pure open multi-processing(OpenMP),pure message passing interface(MPI),and hybrid MPI/OpenMP parallel solvers within the dynamic explicit central difference algorithm for the coining process to address the challenge of capturing fine relief features of approximately 50 microns.Achieving such precision demands the utilization of at least 7 million tetrahedron elements,surpassing the capabilities of traditional serial programs previously developed.To mitigate data races when calculating internal forces,intermediate arrays are introduced within the OpenMP directive.This helps ensure proper synchronization and avoid conflicts during parallel execution.Additionally,in the MPI implementation,the coins are partitioned into the desired number of regions.This division allows for efficient distribution of computational tasks across multiple processes.Numerical simulation examples are conducted to compare the three solvers with serial programs,evaluating correctness,acceleration ratio,and parallel efficiency.The results reveal a relative error of approximately 0.3%in forming force among the parallel and serial solvers,while the predicted insufficient material zones align with experimental observations.Additionally,speedup ratio and parallel efficiency are assessed for the coining process simulation.The pureMPI parallel solver achieves a maximum acceleration of 9.5 on a single computer(utilizing 12 cores)and the hybrid solver exhibits a speedup ratio of 136 in a cluster(using 6 compute nodes and 12 cores per compute node),showing the strong scalability of the hybrid MPI/OpenMP programming model.This approach effectively meets the simulation requirements for commemorative coins with intricate relief patterns.

Schur Forms and Normal-Nilpotent Decompositions

Real and complex Schur forms have been receiving increasing attention from the fluid mechanics community recently,especially related to vortices and turbulence.Several decompositions of the velocity gradient tensor,such as the triple decomposition of motion(TDM)and normal-nilpotent decomposition(NND),have been proposed to analyze the local motions of fluid elements.However,due to the existence of different types and non-uniqueness of Schur forms,as well as various possible definitions of NNDs,confusion has spread widely and is harming the research.This work aims to clean up this confusion.To this end,the complex and real Schur forms are derived constructively from the very basics,with special consideration for their non-uniqueness.Conditions of uniqueness are proposed.After a general discussion of normality and nilpotency,a complex NND and several real NNDs as well as normal-nonnormal decompositions are constructed,with a brief comparison of complex and real decompositions.Based on that,several confusing points are clarified,such as the distinction between NND and TDM,and the intrinsic gap between complex and real NNDs.Besides,the author proposes to extend the real block Schur form and its corresponding NNDs for the complex eigenvalue case to the real eigenvalue case.But their justification is left to further investigations.

Evaluation of Laboratory Request Forms Completion in a Tertiary Medical Laboratory of the Democratic Republic of Congo

Background: The inadequacy in the completeness of the Laboratory Request Form (LRF) has been reported as one of the major sources of errors during the pre-analytical step of laboratory analysis. To prevent the occurrence of such errors, this study aimed at assessing the level of completeness of LRFs. Methods: A retrospective analysis of laboratory request forms was conducted at the Clinical Biology Laboratory of the Kinshasa University Clinic, DR Congo, between November 2021 to May 2022. The LRFs were evaluated according to the completeness of all sections including administrative data of the patient, data of physician who ordered the test, relevant patient’s clinical data and data of the biological sample. Results: From a total of 2842 LRFs evaluated, none was fully completed with all required information. Particularly, patient’s clinical data including the medical history, provisional diagnosis and current treatment, were the most absent in 99% LRFs. However, two sections related to patient’s ID and prescribed test were informed in 100% LRFs. Conclusion: The results of this preanalytical audit can serve as an improvement opportunity focused on strengthening awareness about complete filling of LRF.

Analysis and Optimization of the Electrohydraulic Forming Process of Sinusoidal Corrugation Tubes

Aluminum alloy thin-walled structures are widely used in the automotive industry due to their advantages related to light weight and crashworthiness.They can be produced at room temperature by the electrohydraulic forming process.In the present study,the influence of the related parameters on the forming quality of a 6063 aluminum alloy sinusoidal corrugation tube has been assessed.In particular,the orthogonal experimental design(OED)and central composite design(CCD)methods have been used.Through the range analysis and variance analysis of the experimental data,the influence degree of wire diameter(WD)and discharge energy(DE)on the forming quality was determined.Multiple regression analysis was performed using the response surface methodology.A prediction model for the attaching-die state coefficient was established accordingly.The following optimal arrangement of parameters was obtained(WD=0.759 mm,DE=2.926 kJ).The attaching-die state coefficient reached the peak value of 0.001.Better optimized wire diameter and discharge energy for a better attaching-die state could be screened by CCD compared with OED.The response surface method in CCD was more suitable for the design and optimization of the considered process parameters.

Method of fabricating artificial rock specimens based on extrusion free forming(EFF)3D printing

Three-dimensional(3D)printing technology has been widely used to create artificial rock samples in rock mechanics.While 3D printing can create complex fractures,the material still lacks sufficient similarity to natural rock.Extrusion free forming(EFF)is a 3D printing technique that uses clay as the printing material and cures the specimens through high-temperature sintering.In this study,we attempted to use the EFF technology to fabricate artificial rock specimens.The results show the physico-mechanical properties of the specimens are significantly affected by the sintering temperature,while the nozzle diameter and layer thickness also have a certain impact.The specimens are primarily composed of SiO_(2),with mineral compositions similar to that of natural rocks.The density,uniaxial compressive strength(UCS),elastic modulus,and tensile strength of the printed specimens fall in the range of 1.65–2.54 g/cm3,16.46–50.49 MPa,2.17–13.35 GPa,and 0.82–17.18 MPa,respectively.It is capable of simulating different types of rocks,especially mudstone,sandstone,limestone,and gneiss.However,the simulation of hard rocks with UCS exceeding 50 MPa still requires validation.

Effect of Low pH on Forming Process of Desulfurization Gypsum Composite Boards Strengthened by Melamine-formaldehyde Resin

Through exploring the effects of low pH on the composite system of desulfurization gypsum(DG)enhanced by melamine-formaldehyde resin(MF),it is found that the inducing of sulfate-ion,in contrast to chloride and oxalate ions,favors the longitudinal growth of the crystalline form of the hydration product,which was relatively simple and had the highest length to width(L/D)ratio.At the same time,MF can also improve L/D ratio of gypsum hydration products,which favors the formation of hydrated whiskers.Finally,in a composite system composed of hemihydrate gypsum,MF,and glass fibers,when dilute sulfuric acid was used to regulate pH=3-4,the tight binding formed among the components of the composite system compared to pH=5-6.The hydration product of gypsum adheres tightly to glass fiber surface and produces a good cross-linking and binding effect with MF.The flexural strength,compressive strength,elastic modulus,and water absorption of the desulphurized gypsum composite board is 22.7 MPa,39.8 MPa,5608 MPa,and 1.8%,respectively.

Effect of cold rolling deformation on microstructure evolution and mechanical properties of spray formed Al−Zn−Mg−Cu−Cr alloys

The impact of cold rolling deformation,which was introduced after solid solution and before aging treatment,on microstructure evolution and mechanical properties of the as-extruded spray formed Al−9.8Zn−2.3Mg−1.73Cu−0.13Cr(wt.%)alloy,was investigated.SEM,TEM,and EBSD were used to analyze the microstructures,and tensile tests were conducted to assess mechanical properties.The results indicate that the D1-T6 sample,subjected to 25%cold rolling deformation,exhibits finer grains(3.35μm)compared to the D0-T6 sample(grain size of 4.23μm)without cold rolling.Cold rolling refines the grains that grow in solution treatment.Due to the combined effects of finer and more dispersed precipitates,higher dislocation density and smaller grains,the yield strength and ultimate tensile strength of the D1-T6 sample can reach 663 and 737 MPa,respectively.In comparison to the as-extruded and D0-T6 samples,the yield strength of the D1-T6 sample increases by 415 and 92 MPa,respectively.

A Hybrid Optimization Approach of Single Point Incremental Sheet Forming of AISI 316L Stainless Steel Using Grey Relation Analysis Coupled with Principal Component Analysiss

We investigated the parametric optimization on incremental sheet forming of stainless steel using Grey Relational Analysis(GRA) coupled with Principal Component Analysis(PCA). AISI 316L stainless steel sheets were used to develop double wall angle pyramid with aid of tungsten carbide tool. GRA coupled with PCA was used to plan the experiment conditions. Control factors such as Tool Diameter(TD), Step Depth(SD), Bottom Wall Angle(BWA), Feed Rate(FR) and Spindle Speed(SS) on Top Wall Angle(TWA) and Top Wall Angle Surface Roughness(TWASR) have been studied. Wall angle increases with increasing tool diameter due to large contact area between tool and workpiece. As the step depth, feed rate and spindle speed increase,TWASR decreases with increasing tool diameter. As the step depth increasing, the hydrostatic stress is raised causing severe cracks in the deformed surface. Hence it was concluded that the proposed hybrid method was suitable for optimizing the factors and response.

Study of microstructure evolution of magnesium alloy cylindrical part with longitudinal inner ribs during hot flow forming by coupling ANN-modified CA and FEA

Hot flow forming(HFF)is a promising forming technology to manufacture thin-walled cylindrical part with longitudinal inner ribs(CPLIRs)made of magnesium(Mg)alloys,which has wide applications in the aerospace field.However,due to the thermo-mechanical coupling effect and the existence of stiffened structure,complex microstructure evolution and uneven microstructure occur easily at the cylindrical wall(CW)and inner rib(IR)of Mg alloy thin-walled CPLIRs during the HFF.In this paper,a modified cellular automaton(CA)model of Mg alloy considering the effects of deformation conditions on material parameters was developed using the artificial neural network(ANN)method.It is found that the ANN-modified CA model exhibits better predictability for the microstructure of hot deformation than the conventional CA model.Furthermore,the microstructure evolution of ZK61 alloy CPLIRs during the HFF was analyzed by coupling the modified CA model and finite element analysis(FEA).The results show that compared with the microstructure at the same layer of the IR,more refined grains and less sufficient DRX resulted from larger strain and strain rate occur at that of the CW;various differences of strain and strain rate in the wall-thickness exist between the CW and IR,which leads to the inhomogeneity of microstructure rising firstly and declining from the inside layer to outside layer;the obtained Hall-Petch relationship between the measured microhardness and predicted grain sizes at the CW and the IR indicates the reliability of the coupled FEA-CA simulation results.

Urban Spatial Form Optimization Strategies Based on the Principle of Climate Adaptability of Regional Architecture: A Case Study of Traditional Cave Dwelling Villages in Northern Shaanxi Province

A multitude of climate-adaptive design approaches are embedded in regional architecture,which have a positive impact on addressing the deformed development of urban spatial patterns and the dual challenges of climate and resources.This paper examines the principles of climate adaptability embedded in the site layout and spatial organization characteristics of traditional cave dwelling villages in northern Shaanxi Province.The extracted climate adaptability principles are summarized,and the resulting design strategies that are well-suited to the contemporary urban space form are presented.Through analysis,it can be observed that traditional cave dwelling villages in northern Shaanxi are predominantly situated on south-facing slopes in proximity to water at low altitudes.These villages are characterized by compact building groups and east-west development,which is constrained by the elements of mountains and rivers.A two-level street system is generated,comprising streets parallel to the contour line and roadways perpendicular to the contour line.This results in the formation of a courtyard form enclosed by mountains.Such site layout and spatial organization exhibit excellent climate adaptability with regard to heat,ventilation,and wind storage.In light of the aforementioned considerations,the following urban spatial form design strategies are put forth:①the topographic height difference can be exploited to obtain sufficient sunshine;②the group shape can be optimized in order to reduce building energy consumption;③the best orientation of the building can be chosen to take account of both winter and summer conditions;④the height and length can be combined in order to form natural masking;⑤the D/H ratio of streets and roadways should be controlled to achieve a balance between heat gain and cooling of groups;⑥vents should be set appropriately to optimize group ventilation;⑦climate buffers should be established to increase the level of climate response.

Neutral Pion Electromagnetic Form Factor as a Bound System of 3 + 1 Dimensional QCD

We investigate a neutral pion electromagnetic form factor in momentum space and obtain Gaussian-like function for it. The characteristic form of our neutral pion electromagnetic form factor is consistent with the results published by Jefferson Lab Hall A Collaboration. .