Strain in solidifying shell of continuous casting slabs

Two-dimension unsteady heat transfer model was applied to obtain the surfacetemperature and the shell thickness of continuous casting slabs during the process ofsolidification. On the basis of which, the mathematical model of strain at the interface of solidand liquid steel was set up. Through which, the strain in the solidifying shell under normal andabnormal operation conditions was gained. The results indicate that the strain is small under thenormal operation conditions and the internal crack never happens. However, when the variation of theroll gap is above 2 mm, the strain caused by which is greater than that caused by bulging.Furthermore, the total strain exceeds the critical one and the internal crack is the result. So itis of great importance to maintain the fine state of continuous casting machine to avoid theappearance of internal crack.

Effects of the width and thickness of slabs on broadening in continuous casting

A 3D viscoelastic-plastic thermal-mechanical coupled finite element model was built on the basis of the secondary development of the commercial software MSC.Marc. Numerical simulations were performed to study slab broadening in the secondary cooling zone. The effects of slab width and thickness on slab broadening were considered. The obtained results reveal that the width broadening is noticeable, and the ratio of ultimate broadening slightly increases with the increase of slab width. This agrees well with the measured data in practice. There is no obvious increase in ultimate broadening when the thickness of slabs increases.

Technological Investigation on the Continuous Casting of Mid-Width Thin Slabs

Continuous casting of thin slabs is a key state project for 7th and sth five -year plans. On thebasis of foundamental works , CISRI condueted the tests of 102 heats in Lanzhou Steel Works in the periodof January 1991- June 1992. Three slab assortments of 50× 900 mm . 70 × 900 mm , 70 × 500 mm were ex-amined. In June of 1992, 412 t steel of 46 heats were cast with the efficiency of 91. 3 %. This. result meetsthe requiremeni of the state in this period. The mould, hedt transfer . casting technology and factors influ-encing slab’s qualities are investigated as well.

A Model for Diagnosing the Formation of Internal Cracks in Continuously CastSlabs

The internal cracks in continuously cast slabs are attributed to the excessive tensile strain occurring at the solidifying frontduring the continuous casting process. Based on the understanding, a model for diagnosing the formation of the internal cracks was established, in which the strains at the solidifying front caused by' bulging, straightening or unbending, and roll misalignment were calculated and compared with a critical strain value to estimate whether the internal cracks form. Moreover, the established model was appliedto a real slab caster to reveal the distribution of the strains in casting direction and its effect on the internal cracks. It was proved that themodel was reliable and useful for optimizing the operation of continuous casting.

Evaluation of the performance of mold powder for continuous casting of plate slabs

The No. 3 slab caster,which mainly provides slabs to the 5000 mm plate mill at Baosteel, was put into production in December,2004. The size of the biggest slab produced by this caster is 2300 mm in width and 300 mm in thickness. The designed output of the caster is 2.3 Mt/a. Slab surface longitudinal crack defects,which were related to the heat flux of the mold, frequently occurred in the early stage of the startup of the caster. As mild cooling powder is beneficial to the uniformity of the shell of initial slabs ,the concentration of stress is reduced, and the longitudinal cracking on the surface is avoided. This study evaluates the performance of several kinds of powder, and the results show that mold powder of high basicity, high crystallization proportion and low heat flux is to the benefit of the reduction of the longitudinal cracks on the surface and the defects of slabs.

Research on the trajectory of non-metal inclusions with the flow in the mold during the solidification of continuous casting slabs

By means of the numerical simulation method,the mathematical model of inclusions movement in the mold is established under the condition of austenitic and fen-itic stainless steel slab production. According to the simulation results, the main zones for inclusion particles accumulation were found and many factors that affected floating-up probability of inclusion particles were identified. These factors include the inclusion particle size, the casting speed and the slab width, etc. It is believed that the inclusion particle size is the key one among these factors.

Solidification of horizontally continuous casting of super-thin slab in stable magnetic field and alternating current

The solidified structures of horizontally continuous casting（HCC） of super-thin slab and its relations with the current were studied under the electromagnetic vibration（EMV）.The results show that,under the action of the periodical forces from EMV,the solidified structures of the super-thin slab of pure tin is greatly refined,and the extent of grain refinement is increased with the magnitude of alternating current.For the Sn-10%Pb alloy,it is shown that the EMV promotes the growth of equiaxed grains in the center of super-thin slab,and the grains are refined with the alternating current increasing.This is useful to prevent some solidification defects in the horizontally continuous casting of super-thin slab,such as columnar grains butting,porosity,inclusions and gases gathering,and composition segregation in the centre of slab.

Morphology and Precipitation Kinetics of MnS in Low-Carbon Steel During Thin Slab Continuous Casting Process

The morphology of manganese sulfide formed during thin slab continuous casting process in low-carbon steel produced by compact strip production （CSP） technique was investigated. Using transmission electron microscopy analysis, it was seen that a majority of manganese sulfides precipitated at austenite grain boundaries, the morphologies of which were spherical or close to the spherical shape and the size of MnS precipitates ranged from 30 nm to 100 nm. A mathematical model of the manganese sulfide precipitation in this process was developed based on classical nucleation theory. Under the given conditions, the starting and finishing precipitation temperatures of MnS in the continuous casting thin slab of the studied low-carbon steel are 1 189 ℃ and 1 171 ℃, respectively, and the average diameter of MnS precipitates is about 48 nm within this precipitation temperature range. The influences of chemical components and thermo-mechanical processing conditions on the precipitation behavior of MnS in the same process were also discussed.

Temperature distribution and dynamic control of secondary cooling in slab continuous casting

To predict and optimize the temperature distribution of slab continuous casting in steady operational state, a three-dimensional model （named ＂offline model＂） based on the heat transfer and solidification theories was developed. Both heat transfer and flux distribution characteristics of the nozzle sprays on the slab were considered, and the complicated boundary conditions, such as spray cooling, natural convection, thermal radiation as well as contact cooling of individual rolls were involved in the model. By using the calibrated caster dependent model factors, the calculated temperature and shell thickness accorded well with the measured. Furthermore, a dynamic secondary water cooling control system was also developed on the basis of a two-dimensional transient heat transfer model （named ＂online model＂） and incremental PID control algorithm to reduce slab surface temperature fluctuation in unsteady state. Compared with the traditional spray table control method, the present online model and dynamic PID control demonstrate a higher capability and flexibility to adjust cooling water flowrate and reduce slab surface temperature fluctuation when the casting speed is changed.

Physical modeling of gas-liquid interfacial fluctuation in a thick slab continuous casting mold with argon blowing

Combining with the physical model of level fluctuation in a thick slab continuous casting mold with the cross-section of 1500 mm×280 mm and argon blowing, the rationalities of estimating the level fluctuation by three traditional quantitative approaches were discussed, and the effects of gas flowrate, casting speed, and the immersion depth of submerged entry nozzle （SEN） on the level fluctuation were also investigated. As a result, it seems that three traditional quantitative approaches are not very suitable for estimating the level fluctuation in a mold with argon blowing, so a new approach for estimating level fluctuation in the mold with argon blowing was presented. The experimental results show that the level fluctuation is mainly in the region around the nozzle wall. When the casting speeds are larger than a certain value, there is the escape of large bubbles near the nozzle wall, which causes an obvious increase of level fluctuation. Furthermore, optimal process parameters, viz., the gas flowrate of 6 NL/min, the casting speed of 1.1 m/min, and the immersion depth of 170 mm, are presented to restrain the level fluctuation by a physical model.

Surface turbulence in a physical model of a steel thin slab continuous caster

In the thin slab continuous casting （TSCC） of steel, the issue of optimum fluid flow is very important due to higher casting speeds and has direct influence on the formation of solidified shells and the quality of final products. In the current work, a full-scale physical mod- eling of a thin slab easter on the basis of dimensionless Reynolds and Froude similarity criteria was constructed. The flow pattern in the funnel shaped mold with a new tetra-furcated submerged entry nozzle （SEN） was investigated. To determinate optimum operational parameters, some experiments were carried out under various casting conditions. The results show that the tetra-furcated design of the nozzle leads to a special flow pattern in the mold cavity with three-dimensional recirculating flow. It is also shown that the increase of casting speed and gas injection results in surface turbulence. On the other hand, using a higher depth of SEN decreases the vortex in the free surface of the caster. To avoid surface turbulent and related casting problems, it is recommended to use 30-cm and 40-cm SEN depth at the casting speeds of 3.5 and 4.5 m/min, respectively.

Water modeling of mold powder entrapment in slab continuous casting mold

The optimal parameters were determined by the water modeling of slab casting. It was found that there are mainly three types of mold powder entrapment in slab continuous casting, i.e., the entrapment caused by the shearing flow near the narrow face of mold, the entrapment caused by vortexes around the submerged entry nozzle （SEN）, and the entrapment caused by the Ar bubbling. Both the velocity of the surface flow and the level fluctuation of the liquids are enlarged with increasing the casting speed, reducing the submersion depth of SEN, decreasing the downward angles of the nozzle outlets, and increasing the Ar flowrate, all of which increase the tendency of mold powder entrapment. Among the four above-mentioned factors, casting speed has the largest effect.

Characteristics of shell thickness in a slab continuous casting mold

The key to reduce shell breakout in the continuous casting process is to control shell thickness in the mold. A numerical simulation on the turbulent flow and heat transfer coupled with solidification in the slab mold using the volume of fluid （VOF） model and the enthalpy-porosity scheme was conducted and the emphasis was put upon the flow effect on the shell thickness profiles in longitudinal and transverse directions. The results show that the jet acts a stronger impingement on the shell of narrow face, which causes a zero-increase of shell thickness in a certain range near the impingement point. The thinnest shell on the slab cross-section locates primarily in the center of the narrow face, and secondly near the comer of the wide face. Nozzle optimization can obviously increase the shell thickness and make it more uniform.

Influence of submerged entry nozzle clogging on the behavior of molten steel in continuously cast slab molds

The influence of submerged entry nozzle clogging on the behavior of molten steel in continuously cast slab molds was studied using commercial code CFX4.3. The results indicate that clogging at the top part of the nozzle port not only increases the velocity of molten steel, but also enhances the wall shear stress, F number and heat flux. This clogging has the greatest effect on the behavior of molten steel. However, clogging at the top 1/3 of the nozzle only increases the velocity of molten steel and has little influence. Clogging at the bottom of the nozzle almost has no influence.

Formation mechanism of internal cracks in continuously cast slab

In order to make clear the formation mechanism of centerline cracks incontinuously cast slabs, the form, distribution and other characteristics of the cracks wereanalyzed. The final solidification point, surface temperature of the slabs and strain in solidifyingshell were investigated. The results were that: (1) Five relatively low temperature zones exist onslab surface below the three water spraying nozzles and near the two edges, respectively, whichcorresponds to the places of centerline cracks and triangle-zone cracks. (2) Centerline cracks andtriangle-zone cracks occur because of weak secondary cooling, uneven cooling along slab width, andlarge variation of roll gap. (3) After minimizing the variation of roll gap and applying the newsecondary cooling pattern, the occurring frequency of centerline and triangle-zone cracks minimizesto zero.

Longitudinal crack on slab surface at straightening stage during continuous casting using finite element method

Deformation behavior of slab at the straightening stage during continuous casting was simulated by the explicit dynamic finite element method,and the stress distribution along the width direction of the slab and its change regularity at slab center during continuous casting were obtained.The influence of distribution and change of stress on the propagation of longitudinal cracks on slab surface was discussed.The results show that the tensional stress appears on slab surface at the inner arc side and the compressive stress appears on slab surface at the outer arc side at stages 6-8 in straightening zone during continuous casting.Longitudinal cracks generally appear on slab top surface and do not appear on slab bottom surface,which are also observed in industry.

STUDY OF DYNAMIC RECRYSTALLIZATION OF LOW CARBON STEEL IN THIN SLAB CONTINUOUS ROLLING PROCESS

Combined with the technological characteristics of thin slab continuous rolling process （TSCR）, dynamic recrystallization of an extremely coarse austenite of low carbon steel is studied by Thermecmaster-Z hot simulator. By the analysis of true stress-strain curves and the observation of microstructures at different deformation stages, the critical stress and critical strain are determined under different deformation conditions. The effect of Z parameter on dynamic recrystallization of coarse austenite is studied. The microstructure evolution in real production is also discussed.

Numerical Evaluation of Two k-εTurbulence Model for Predicting Flow and Solidification in Continuous Casting Slab

A steady three-dimensional fluid flow and solidification model was built based on CFD software by high-Reynolds-number and Lam-Bremhorst low-Reynolds-number k-ε model.During the simulation,the fixed-grid enthalpy-porosity technique was used to represent the solidification,and Darcy law was adopted to simulate the flow in mushy region.The prediction for steel flow and solidification was evaluated by the comparison of two turbulence models.It is found that both Lam-Bremhorst low-Reynolds-number and high-Reynolds-number k-ε models predict the same trend of the steel flow and temperature distribution.However,due to the effect of turbulent flow on heat transfer,the low-Reynolds-number turbulence model predicts longer penetration depth of molten steel in sub-mold region,less shell growth and higher shell surface temperature at the narrow face compared with standard k-ε model.

INVESTIGATION ON HOT DUCTILITY AND STRENGTH OF CONTINUOUS CASTING SLAB FOR AH32 STEEL

By means of Gleeble-1500 testing machine, the simulation of continuous casting process forAH32 steel was carried out and hot ductility and strength were determined. The cracking sensitivity was studied under the different temperatures and strain rates. The Precipitations of AIN at different temperatures and the fractures of high-temperature tensile samples were observed by using TEM （transmission electron microscope） and SEM （scanning electron microscope）. The factors affecting the brittle temperature zone were discussed.

Numerical Simulation of Fluid Flow and Heat Transfer in Funnel Shaped Mold of Thin Slab Continuous Caster

Thin slab casting is used widely in the world. The control of molten steel flow and solidification in the mold is difficult due to the high casting speed and complicated configuration of the mold. Numerical simulation was carried out to study the fluid flow and heat transfer in the funnel shaped mold. The influence of nozzle design, casting speed and nozzle submersion depth on the flow and temperature fields in the mold was investigated, and guidance for selecting configurations of submerged nozzle was obtained.