Strengthening effect of prefabrication(10-12)tensile twinning on AZ80+0.4%Ce magnesium alloy and inhibition mechanism of discontinuous precipitation

This paper provided an effective method to further improve the mechanical properties of the AZ80+0.4%Ce magnesium alloy wheel spoke.The effect of high strength and ductility was obtained with a yield strength of 295.36 MPa,an elongation of 10%,by the combination of pre-deformation(7%deformation)and two-stage aging treatment(120℃/9 h+175℃/24 h).The evolution of the microstructure and properties of the alloy was explored under the coupling conditions of different pre-deformation degrees and multi-stage aging.The results show that,pre-deformation introduced a large number of(1012)tensile twinning and dislocations,which greatly promoted the probability of continuous precipitates(CPs)appearing.On the contrary,the discontinuous precipitates(DPs)were limited by the vertical and horizontal twin structure.As a result,the pre-nucleation method of two-stage aging increased the proportion of CPs by 34%-38%.Owing to the DPs was effectively suppressed,the alloy's yield strength has been greatly improved.Besides,under multi-stage aging,the twin boundaries induce protruding nucleation to form static recrystallization by hindering the migration of dislocations,and the matrix swallows the twins,then the texture gradually tilts from the two poles to the basal plane.As an important supplement,the grain refinement and oblique texture promoted the improvement of the yield strength of the component.

Equilibrium Phase Constituents and Discontinuous Precipitation Behavior of Al-Zn-Cu Alloy with Symmetrical Composition

Through microstructure observation and X-ray diffraction analysis, the equilibrium phase constituents of Al-Zn alloy that contains 2 at. pct Cu at room temperature have been determined as Al-based solid solution (α), Zn-based solid solution and AI4Cu3Zn phase (T'-phase), which are different from a phase, Zn phase and CuZn4 phase originally believed. It is determined that the products of discontinuous precipitation transformation below 277℃ are not the equilibrium phase constituents, but the metastable phases made up of a phase, Zn phase and CuZn4 phase. The phase constituents after discontinuous precipitation of AIZn-2Cu alloy would transform to the ones in equilibrium status: Al-based solid solution (α) in fcc structure, Zn-based solid solution in hcp structure and AI4Cu3Zn phase (T'-phase) ultimately through plastic deformation at room temperature and re-heating treatment below 277℃.

Recrystallization of the cold-deformed discontinuous precipitation microstructure in Al-Zn (-Cu) alloys

Recrystallization of cold-rolled discontinuous, precipitation microstructurewhich has fine laminar structure in an Al-40 percent Zn (atom fraction) binary alloy is investigatedby optical microscopy, SEM and TEM. It is found that there are two kinds of recrystallizationmechanisms: continuous coarsening (CC) and discontinuous coarsening (DC). The latter can be dividedinto coarsening mainly driven by stored deformation energy at colony boundaries and slip bands andthe one mainly driven by boundary energy in the area with little deformation. It is shown that theaddition of Cu can retard the nucleation of coarsening cells and their growth. X-Ray diffractionanalysis indicated the metastable phase CuZn_4 transformed into equilibrium phase A;_4Cu_3Zn duringthe heating process.

Effect of Cu on Discontinuous Precipitation of a Symmetrical AlZn Alloy

The effect of Cu additions on discontinuous precipitation of AlZn alloy were studied with optical microscopy, scanning electron microscopy and X-ray diffraction. It is found that the effect of addition of 2 at. pct Cu on cellular nucleation site is not remarkable, while the effect of aging temperature on cellular nucleation site of AlZn and AIZn-2Cu alloys is fairly obvious. The cell growth rate of discontinuous precipitation of AlZn alloy is remarkably accelerated with the addition of 2 at. pct Cu. The discontinuous precipitation microstructure of AlZn alloy is not apparently affected with the addition of 2 at. pct Cu and the cellular front is still fine microstructure of spinodal decomposition. The phase constituents consist of a fcc Al-rich phase, a hcp Zn-rich phase and a CuZn4 phase. The transformation rate of discontinuous precipitation of AlZn alloy is remarkably accelerated with the addition of 2 at. pct Cu.

Discontinuous Precipitation and Dissolution in Cu-4, 6 at% In Alloy under the Effect of Plastic Deformation and the Temperature

The study of the discontinuous precipitation reaction and the lamellar precipitate dissolution in the alloy Cu-In system provoked a considerable benefit and has been the subject of many theoretical and experimental investigations. The aim of this work is to make the evidence on the one hand the effect of the plastic deformation on the mechanism of the discontinuous precipitation reaction such as nucleation, growth and lamellar coarsening and in other hand the effect of temperature on the characteristics and front behavior movement of the opposite reaction (discontinuous dissolution). Different techniques of analysis have been used in this respect such as the optical microscopy, the differential thermal analysis and the microhardness Vickers. The obtained results confirm various works achieved in this field.

Discontinuous Precipitation and Dissolution under the Influence of the Plastic Strain and Temperature in Al-15 at.%Zn and Al-30 at.%Zn Alloys

The discontinuous precipitation and dissolution in the alloy Al-Zn system has been the subject of many theoretical and experimental investigations that have contributed to the understanding of the different mechanisms which control them. However, many questions remain unanswered because of the complexity of the constituted phases which are affected by the speed of the quenched, deformation, the temperature of homogenization and ageing effect. The purpose of this work is to clarify the effect of temperature and deformation on the mechanisms of these two reactions during ageing of Al-15 at.% Zn and Al-30 at.% Zn alloy. The techniques of analysis used in this respect are the optical microscopy, the X-ray diffraction and the hardness Vickers.

Discontinuous Precipitation Reaction Front of Cellular Recrystallization for a Single-Crystal Superalloy Studied by Electron Microscopy

Combining analytical transmission electron microscopy systematic tilting, scanning transmission electron microscopy mapping and nano-beam electron diffraction operations, we obtain direct experimental proofs on the boundary type, elemental distribution and structure of the cellular reerystallization reaction front for a single- crystal superalloy. It is demonstrated that the cellular recrystallization reaction front usually corresponds to coincidence site lattice boundaries, and a thin layer of γ-forming elements such as Re, Cr, Mo and Co invariably exists in the direct reaction front. Furthermore, the thin layer with γ-forming elements is proved to be γ phase, with the same orientation as the neighboring original matrix.

Fourier Continuation Discontinuous Galerkin Methods for Linear Hyperbolic Problems

Fourier continuation(FC)is an approach used to create periodic extensions of non-periodic functions to obtain highly-accurate Fourier expansions.These methods have been used in partial differential equation(PDE)-solvers and have demonstrated high-order convergence and spectrally accurate dispersion relations in numerical experiments.Discontinuous Galerkin(DG)methods are increasingly used for solving PDEs and,as all Galerkin formulations,come with a strong framework for proving the stability and the convergence.Here we propose the use of FC in forming a new basis for the DG framework.

Improved continuous precipitation kinetics and tensile properties of extruded AZ80 alloy through {10-12} twin formation

This study investigates the effect of{10-12}deformation twins on the continuous precipitation behavior of an extruded Mg-8.0Al-0.5Zn-0.2Mn(AZ80)alloy during aging.The extruded AZ80 alloy is compressed along the transverse direction to introduce{10-12}twins,followed by an aging treatment at 300℃.The extruded material exhibits a twin-free microstructure with low internal strain energy,whereas the pre-twinned material possesses abundant{10-12}twins and has high internal strain energy.The aging results reveal that the peak-aging time of the pre-twinned material(1 h)is one-eighth of that of the extruded material(8 h).Although Mg_(17)Al_(12)continuous precipitates(CPs)are observed in both the peak-aged materials,these CPs are much smaller and more densely distributed in the pre-twinned material despite the significantly shorter aging time.The CPs size in the peak-aged materials increases in the following order:twinned region in the pre-twinned material(0.47μm)<residual matrix region in the pre-twinned material(1.71μm)<matrix region in the extruded material(2.55μm).Moreover,the CPs number density in the twinned region of the pre-twinned material is approximately 11 times higher than that in the matrix region of the extruded material.The peak-aged pre-twinned material exhibits significantly higher tensile strength and ductility than the peak-aged extruded material.These results demonstrate that the formation of{10-12}twins in the extruded AZ80 alloy substantially accelerates the static precipitation of CPs during aging at 300℃and improves the tensile properties of the peak-aged material.

Effect of aging time on discontinuous precipitates,continuous precipitates and mechanical properties of AZ80A magnesium alloy

The evolution of precipitates and mechanical properties of AZ80A magnesium alloy with aging time was studied by in situ observation with SEM,TEM and tensile testing.The results show that the continuous precipitation(CP)phases near the reaction front(RF)are replaced by the discontinuous precipitation(DP)phases at the early aging stage.In DP regions,the elliptical phases coarsen obviously with the increase of aging time,which results in a slightly slow reduction of the intracrystalline hardness of DP regions.In CP regions,some small plate phases reprecipitate simultaneously with the growth of the initial precipitates,which contributes to a slight increase in the intracrystalline hardness in CP regions at the later aging stage.The aging hardening of DP regions is faster and stronger than that of CP regions.However,the age strengthening of CP regions not only compensates for the overaging softening of DP regions but also improves the strength of the alloy.

Analysis of the Maximum Continuous Precipitation Variation in Shenyang in 48 Years

[Objective] The aim was to study the changes of maximum continuous precipitation in Shenyang in recent 48 years.[Method] By dint of the daily precipitation from May to September from 1961 to 2008 and according to simple linear trend estimates and microwave analysis,the maximum consecutive precipitation in each month was analyzed.[Result] The frequency of extreme value for the maximum consecutive precipitation in Shenyang increased since 1990.The decreasing trend of maximum consecutive precipitation from May to September was consistent with that around 1990.The decrease of maximum consecutive precipitation amount had tendency to decrease along with the passing of time.There was 5 years temporal scale period of maximum consecutive precipitation from May to September in Shenyang.Maximum value occurred in 1973 and the minimum value occurred in 2000.[Conclusion] The study had important reality meaning to the understanding of climate changes in Shenyang and disaster prevention and relief work of extreme climate incidents.

Morphology and Precipitation Kinetics of MnS in Low-Carbon Steel During Thin Slab Continuous Casting Process

The morphology of manganese sulfide formed during thin slab continuous casting process in low-carbon steel produced by compact strip production （CSP） technique was investigated. Using transmission electron microscopy analysis, it was seen that a majority of manganese sulfides precipitated at austenite grain boundaries, the morphologies of which were spherical or close to the spherical shape and the size of MnS precipitates ranged from 30 nm to 100 nm. A mathematical model of the manganese sulfide precipitation in this process was developed based on classical nucleation theory. Under the given conditions, the starting and finishing precipitation temperatures of MnS in the continuous casting thin slab of the studied low-carbon steel are 1 189 ℃ and 1 171 ℃, respectively, and the average diameter of MnS precipitates is about 48 nm within this precipitation temperature range. The influences of chemical components and thermo-mechanical processing conditions on the precipitation behavior of MnS in the same process were also discussed.

Cerium dioxide with large particle size prepared by continuous precipitation

Cerium dioxide(CeO2) has attracted much attention and has wide applications such as automotive exhaust catalysts,polishing materials for optical glasses and additives for advanced glasses,as well as cosmetic materials.The particle size and its distribution are key factors to the performance of the materials in the functional applications.However,control of particle size is still a challenge in materials synthesis.Therefore,continuous precipitation of cerium oxalate(precursor of ceria) was carried out at dif...

Continuous Dependence of Bounded Φ-variation Solutions on Parameter for a Class of Discontinuous Systems

The functions of bounded φ-variation are development and generalization of bounded variation functions in the usual sense.Henstock-Kurzweil integral is a very useful tool for some discontinuous systems. In this paper, by using Henstock-Kurzweil integral, we establish theorems of continuous dependence of bounded D-variation solutions on parameter for a class of discontinuous systems on the base of D-function. These results are essential generalizations of continuous dependence of bounded variation solutions on parameter for the systems.

Continuous cooling precipitation diagram of high alloyed Al-Zn-Mg-Cu 7049A alloy

The precipitation behaviour during cooling from solution annealing of high alloyed 7049A aluminium alloy was investigated, covering the complete cooling-rate-range of technical interest. This ranges from slow cooling rates close to equilibrium up to rates above complete supersaturation and is covering seven orders of magnitude in cooling rate （0.0005 to 5000 K/s）. The continuous cooling precipitation behaviour of 7049A alloy was recorded by combining different differential scanning calorimetry （DSC） techniques and microstructure analysis by SEM and Vickers hardness testing. The high alloyed, high strength and quench sensitive wrought aluminium alloy 7049A was investigated during quenching from solution annealing by conventional DSC in the cooling rate range of 0.0005 to 4 K/s. In this range at least two exothermal precipitation reactions were observed： a high temperature reaction in a narrow temperature interval of 450-430℃, and a low temperature reaction in a broad temperature interval down to about 200 ℃. Intensities of both reactions decreased with increasing cooling rate. Quenching from solution annealing with rates up to 1000 K/s was investigated by differential fast scanning calorimetry （DFSC） and the differential reheating method （DRM）. A critical quenching rate to suppress all precipitation reactions of 100-300 K/s was been determined.

A continuous-discontinuous cellular automaton method for cracks growth and coalescence in brittle material

A method of continuous-discontinuous cellular automaton for modeling the growth and coalescence of multiple cracks in brittle material is presented. The method uses the level set to track arbitrary discontinuities, and calculation grids are independent of the discontinuities and no remeshing are required with the crack growing. Based on Grif- fith fracture theory and Mohr-Coulumb criterion, a mixed fracture criterion for multiple cracks growth in brittle mate- rial is proposed. The method treats the junction and coales- cence of multiple cracks, and junction criterion and coales- cence criterion for brittle material are given, too. Besides, in order to overcome the tracking error in the level set ap- proximation for crack junction and coalescence, a dichotomy searching algorithm is proposed. Introduced the above the- ories into continuous-discontinuous cellular automaton, the present method can be applied to solving multiple crack growth in brittle material, and only cell stiffness is needed and no assembled global stiffness is needed. Some numerical examples are given to shown that the present method is efficient and accurate for crack junction, coalescence and percolation problems.

Continuous cooling precipitation diagram of cast aluminium alloy Al-7Si-0.3Mg

The precipitation behaviour during quenching of cast Al-7Si-0.3Mg aluminium alloy was investigated by DSC in the cooling rate range of 0.01 K/s to 3 K/s and by quenching dilatometry for higher rates. Two main precipitation reactions were observed during cooling, a high temperature reaction starting almost directly with quenching from 540℃ and a low temperature reaction starting at about 400℃. Quenching with 3 K/s already significantly suppresses precipitation during quenching. Hardness after T6 ageing increases with increasing quenching rate, due to the increasing content of supersaturated solid solution. By dilatometry and hardness results the critical cooling rate can be estimated as about 60 K/s. Quenched Al-7Si-0.3Mg microstructures have been investigated by light microscopy. The microstructures consist of an aluminium-silicon eutectic structure, aluminium solid solution dendrites and precipitates inside the aluminium dendrites, depending on quenching rate.

Continuous dynamic recrystallization and discontinuous dynamic recrystallization in (99.99%) polycrystalline aluminum during hot compression

The dynamic restoration behavior of 99.99% polycrystalline aluminum was investigated. The deformation was carried out by compression test at 533773 K and initial strain rate of 0.0022 s-1 to a true strain of （1.0） followed by water quench. Polarized optical microscopy and transmission electron microscopy were applied to observe the deformation microstructure. It’s found that discontinuous dynamic recrystallization, which is commonly observed in lower stacking fault energy metals or ultra-high purity aluminum（≥99.999%）, occurs when Zenner-Hollomon parameter（Z parameter） is low, but the true stress—strain curve doesn’t accompany stress oscillation. Continuous dynamic recrystallization occurs when Z parameter is intermediate, and only dynamic recovery takes place if Z parameter is high.

Purification of Pseudomonas sp. Lipase by Continuous Elution Electrophoresis Based on Pb^(2+) Precipitation Method

A Pb 2+ precipitation method was designed to get rid of the impure proteins in a lipase. The results show that it was a simple way in the primary treatment of the crude samples and about 20% impure proteins were removed in the precipitation step. Further, continuous elution electrophoresis was also applied as a preparative technique for attaining the highly pure lipase. During the continuous elution electrophoresis, the enzyme was eluted as a single peak and 5.7-fold purification was achieved in a yield of 54.3%. The two steps finally yielded an electrophoretically homogeneous enzyme.

Influence of Plastic Deformation on Occurrence of Discontinuous Reaction in Ni-In Alloy

The morphology and growth kinetics of the discontinuous precipitate in a deformed and undeformed Ni-7.5at.%In alloy have been investigated at temperatures ranging from 667?K to?1030?K using light and scanning microscopy. Also, the dependence of the growth rate on some diffusion parameters was experimentally and theoretically studied. The investigation is observed that at all aging temperatures the alloy was observed to decompose completely by discontinuous precipitation into a fine lamellar structure of nickel-rich solid solution and?β?(Ni3In) precipitate phase. The precipitation rate depends strongly on the degree of deformation, this dependence being identical for each of the aging temperatures under investigation. Analysis of the growth rates, lamellar spacing and phase compositions for the discontinuous precipitation reaction showed that they were controlled by grain boundary diffusion. Moreover, a generally applicable procedure for calculating the driving force is presented. The driving forces, calculated in this way, should be more reliable than those calculated with the approximations based on Peterman and Hornbogen laws.