Formation mechanism of internal cracks in continuously cast slab

In order to make clear the formation mechanism of centerline cracks incontinuously cast slabs, the form, distribution and other characteristics of the cracks wereanalyzed. The final solidification point, surface temperature of the slabs and strain in solidifyingshell were investigated. The results were that: (1) Five relatively low temperature zones exist onslab surface below the three water spraying nozzles and near the two edges, respectively, whichcorresponds to the places of centerline cracks and triangle-zone cracks. (2) Centerline cracks andtriangle-zone cracks occur because of weak secondary cooling, uneven cooling along slab width, andlarge variation of roll gap. (3) After minimizing the variation of roll gap and applying the newsecondary cooling pattern, the occurring frequency of centerline and triangle-zone cracks minimizesto zero.

Morphology and Precipitation Kinetics of MnS in Low-Carbon Steel During Thin Slab Continuous Casting Process

The morphology of manganese sulfide formed during thin slab continuous casting process in low-carbon steel produced by compact strip production （CSP） technique was investigated. Using transmission electron microscopy analysis, it was seen that a majority of manganese sulfides precipitated at austenite grain boundaries, the morphologies of which were spherical or close to the spherical shape and the size of MnS precipitates ranged from 30 nm to 100 nm. A mathematical model of the manganese sulfide precipitation in this process was developed based on classical nucleation theory. Under the given conditions, the starting and finishing precipitation temperatures of MnS in the continuous casting thin slab of the studied low-carbon steel are 1 189 ℃ and 1 171 ℃, respectively, and the average diameter of MnS precipitates is about 48 nm within this precipitation temperature range. The influences of chemical components and thermo-mechanical processing conditions on the precipitation behavior of MnS in the same process were also discussed.

INVESTIGATION ON HOT DUCTILITY AND STRENGTH OF CONTINUOUS CASTING SLAB FOR AH32 STEEL

By means of Gleeble-1500 testing machine, the simulation of continuous casting process forAH32 steel was carried out and hot ductility and strength were determined. The cracking sensitivity was studied under the different temperatures and strain rates. The Precipitations of AIN at different temperatures and the fractures of high-temperature tensile samples were observed by using TEM （transmission electron microscope） and SEM （scanning electron microscope）. The factors affecting the brittle temperature zone were discussed.

Strain in solidifying shell of continuous casting slabs

Two-dimension unsteady heat transfer model was applied to obtain the surfacetemperature and the shell thickness of continuous casting slabs during the process ofsolidification. On the basis of which, the mathematical model of strain at the interface of solidand liquid steel was set up. Through which, the strain in the solidifying shell under normal andabnormal operation conditions was gained. The results indicate that the strain is small under thenormal operation conditions and the internal crack never happens. However, when the variation of theroll gap is above 2 mm, the strain caused by which is greater than that caused by bulging.Furthermore, the total strain exceeds the critical one and the internal crack is the result. So itis of great importance to maintain the fine state of continuous casting machine to avoid theappearance of internal crack.

Numerical Simulation of Fluid Flow and Heat Transfer in Funnel Shaped Mold of Thin Slab Continuous Caster

Thin slab casting is used widely in the world. The control of molten steel flow and solidification in the mold is difficult due to the high casting speed and complicated configuration of the mold. Numerical simulation was carried out to study the fluid flow and heat transfer in the funnel shaped mold. The influence of nozzle design, casting speed and nozzle submersion depth on the flow and temperature fields in the mold was investigated, and guidance for selecting configurations of submerged nozzle was obtained.

EFFECT OF SEN DESIGN ON SURFACE FLUCTUATION AND SOLIDIFYING SHELL IN SLAB MOLD AND ITS OPTIMIZATION

Turbulent flow and heat transfer coupled with solidification in slab continuous casting mold was studied by numerical simulation method. Volume of fluid （VOF） model is used to solve steel-air two-phase flow problem and enthalpy-porosity scheme is introduced to solve the fluid flow problem involving solidification. Contributions of various nozzle port angles and port widths and heights on the free surface fluctuation and the thickness of solidifying shell in slab mold were particularly investigated, based on which the structure of submerged entry nozzle was optimized. Flow inside the common nozzle port cannot fill the entire outlet area, having a recirculation in the upper portion of the port, which is enlarged for the nozzle port with both larger height and width. Results show that the flow in mold cavity is mainly controlled by the nozzle port angle. The increase of the angle of upper face of the port to shape a roughly streamlined inner-wall improves the effective area fraction of the nozzle, resulting in less jet impingement, weaker free surface turbulence and thicker solidifying steel shell.

Flow and Temperature Fields in Slab Continuous Casting Molds

In order to develop super-board and super-thick slabs, the flow and temperatur fields were studied in slab continuous casting molds under different practical conditions, such as slab dimensions, with-drawing slab speed, design of nozzles, and superheat tempera-ture. The results showed that it is preferred to incline nozzle bores downwards and the submerged depth of the nozzles is best kept be-tween 250-300 mm. In addition, the solidified shell is thicker at the wide face than that at the narrow face, while the thin points alongthe wide face ekist both in the center and in the some area toward each respective end.

Modeling of unsteadiness of fluid flows and level fluctuations in thin slab continuous casting moulds

Unsteady fluid flows and level fluctuations in a thin slab continuous casting mould have significant influence on product quality. In this study, the phenomena concerning transient flow features and free surface motions were analyzed by means of the large eddy simulation （LES） software with the smagorinsky SGS model--VisualCast （VCast） II, where the Simpler algorithm on a body-fitted mesh was used to resolve governing equations. A series of water analog experiments on the fluid flow and the surface wave in the moulds of thin slab continuous casting were also performed. The results of fluid regions, middle of vortex and level fluctuation from digital simulations were identical with the results of the water analog experiments.

Study Segregation of Alloying Elements in Continuous Casting Slab with Valence Electron Structure

By calculating the electron structures of the phases that phosphor, sulfur and alloying elements dissolving inγ-Fe, the reason why alloying elements can bring centerline segregation in continuous casting slab (CCS) with nA, the number of electrons on the strongest covalent bonds, and the structure formation factor S were investigated, and an electron structural criterion to control and to eliminate the centerline segregation was advanced. Basing on this, the electron structures of a part of rare earth phosphides and sulfides are calculated, the physical mechanism that rare earth elements can control the segregation of phosphor and sulfur is analyzed, and the criterion is well verified.

Research on the trajectory of non-metal inclusions with the flow in the mold during the solidification of continuous casting slabs

By means of the numerical simulation method,the mathematical model of inclusions movement in the mold is established under the condition of austenitic and fen-itic stainless steel slab production. According to the simulation results, the main zones for inclusion particles accumulation were found and many factors that affected floating-up probability of inclusion particles were identified. These factors include the inclusion particle size, the casting speed and the slab width, etc. It is believed that the inclusion particle size is the key one among these factors.

Effects of electromagnetic stirring on surface purity of IF steel slabs

In order to analyze the effect of electromagnetic stirring on the slab＇ s surface purity, the continuously cast slab surface inclusions and subsurface blisters have been investigated. The results indicate that the mold electromagnetic stirrer （M -EMS） is useful for the improvement of IF steel slabs＇ surface quality. The continuously cast slab surface inclusions and subsurface blisters have been significantly reduced. The distribution of bubbles in the slab is non-homogeneous in terms of both width and depth. The continuously cast slab surface inclusions tend to miniaturization through M-EMS and most of the inclusions are less than 10 μm in size.

Technological Investigation on the Continuous Casting of Mid-Width Thin Slabs

Continuous casting of thin slabs is a key state project for 7th and sth five -year plans. On thebasis of foundamental works , CISRI condueted the tests of 102 heats in Lanzhou Steel Works in the periodof January 1991- June 1992. Three slab assortments of 50× 900 mm . 70 × 900 mm , 70 × 500 mm were ex-amined. In June of 1992, 412 t steel of 46 heats were cast with the efficiency of 91. 3 %. This. result meetsthe requiremeni of the state in this period. The mould, hedt transfer . casting technology and factors influ-encing slab’s qualities are investigated as well.

The optimization of mold fluxes used for casting the peritectic steel of heavy slabs at Baosteel

In order to solve the problem of the high surface longitudinal crack ratio of heavy peritectic steel slabs produced by the No. 3 continuous caster at Baosteel,the physical properties of the original mold flux and the optimized mold flux were compared in a comprehensive way by using analytical measures, such as a slag film heat-flow simulator, a thermowire molten flux crystallization tester and an X-ray diffractometer in the laboratory. The results reveal that one of the major reasons for the cracks is the poor heat transfer ability of the original mold flux. However, the optimized mold flux with a high basicity features a high crystallizing rate,low crystallization temperature and low heat-flow density. Therefore, the optimized mold flux is more suitable for casting peritectic steel by the heavy slab continuous caster. The test results show that the slabs produced by using the optimized mold flux had no surface longitudinal crack in four test casts, while the surface longitudinal crack ratio of the slabs produced by using the original mold flux was 5%. The optimized mold flux can effectively prevent slab surface longitudinal cracks from occurring.

Modeling and control of dynamic soft reduction in continuous slab casting

The centerline segregation in continuous casting steel is known to be formed by the interdendritic enriched liquid flow at the solidification end in strand.At present,several methods,such as thermal soft reduction, electromagnetic stirring and dynamic soft reduction,are available to reduce the center segregation and to improve the internal quality.Although some methods could alleviate center segregation to some extent,they can also give rise to new problems.For instance,thermal soft reduction can lead to surface cracking during casting of some steels and electromagnetic stirring can result in white band.Dynamic soft reduction is an effective technology for the improvement of strand quality in continuous slab casting.In this paper,the key parameters of dynamic soft reduction technology,such as soft reduction region,the total reduction amount,for low carbon steel have been studied based on experimental and theoretical analysis.The soft reduction region was related to the segregation of chemical composition,slab bulging of narrow side and avoiding internal crack of slab.The total reduction amount was composed of natural thermal shrinkage and actual reduction amount depending on critical strain.For low carbon steel with slab dimension of(950 - 1 950) mm×170 mm,the solid fraction range in soft reduction region was recommended from 0.4 to 0.8,the total reduction amount was 2.0 -2.8 mm,and the optimized reduction rate was 0.4 - 1.2 mm/min,respectively.Furthermore,a dynamic soft reduction system in continuous slab casting, Visual Cast-Dynamic,has been developed by multithreading method.It demonstrated that the dynamic soft reduction model in this study was correct with the ability of online control.

Simulation of thermal behavior during peritectic steel solidification in slab continuous casting mold

Thermal behavior of the solidifying shell in continuous casting mold is very important to final steel products.In the present work,one two-dimension transient thermal-mechanical finite element model was developed to simulate the thermal behavior of peritectic steel solidifying in slab continuous casting mold by using the sequential coupling method.In this model,the steel physical properties at high temperature was gotten from the micro-segregation model withδ/γtransformation in mushy zone,and the heat flux was obtained according to the displacement between the surface of solidifying shell and the hot face of mold as solidification contraction,the liquid-solid structure and distribution of mold flux,and the temperature distribution of slab surface and mold hot face,in addition,the rate-dependent elastic-viscoplastic constitutive equation was applied to account for the evolution of shell stress in the mold.With this model,the variation characteristics of surface temperature,heat flux, and growth of the solidifying shell corner,as well as the thickness distribution of the liquid flux,solidified flux,air gap and the corresponding thermal resistance were described.

Numerical simulation of fluid flows in a slab continuous casting mold under electromagnetic stirring

This study established a three-dimensional mathematical model to determine the fluid flow in a slab continuous casting mold under an electromagnetic stirring force. The flow structure and distribution were studied with respect to different continuous casting parameters and stirring current. Based on the calculation results, the mold flux entrapment index in free surface and velocity uniformity index were used to evaluate the flow field in the mold. The theoretical basis for the optimization of the flow field structure was provided. The study also suggested an optimization method for electromagnetic stirring parameters.

Physical modeling and numerical simulation of electromagnetic stirring in a slab continuous casting mold

Through physical modeling and numerical simulation,the flow field in a slab continuous casting mold with electromagnetic stirring is measured under different casting parameters and stirring currents. To qualitatively evaluate the flow field in the mold, two indexes,i, e., mold flux entrapment and velocity uniformity, are proposed. Based on these two indexes, some optimized stirring parameters under different casting conditions can be determined.

Quality Control for Continuously Cast Slab of High Strength Weathering Steel Q450NQR1

In order to reduce the transverse corner cracks of high strength weathering steel Q450NQR1,the factors influencing transverse corner cracks on continuously cast slab,such as level fluctuation of molten steel in mold,mold taper,primary cooling,mold powder,secondary cooling,nitrogen content in steel,spray nozzle structure,processing parameters and equipment of CC,etc.,were analyzed.Based on this,a series of comprehensive countermeasures have been proposed.The operation shows by the use of key technologies,including stabilizing steel level,optimizing the mold taper,weakening the primary cooling and the secondary cooling,reforming the mold powder,and adjusting spray nozzle structure,the transverse corner cracks on continuously cast slab have been significantly reduced,and the edge cracks on hot rolled sheet have been eliminated due to the transverse corner cracks.The qualified slabs are delivered to produce weathering cold forming sectional steel,whose yield strength is greater than 450MPa.

Research on electromagnetic properties of electromagnetic stirring roller

Using computer simulation and test measurements,the relationship between the electromagnetic properties of an electromagnetic stirring roller and the roller structure parameters was analyzed and compared. The distribution of the magnetic field,magnitude of the electromagnetic force,and matched-load characteristics were systematically investigated at different parameter values for the induction coils,iron core,shield,and roller sleeve.The results indicate that the change in the electromagnetic force with stirring frequency is non-linear and has a maximum value higher than 10 Hz;the electromagnetic force largely depends on the diameter of the core;and there is a mutual restriction relationship between the two-phase imbalance and the electromagnetic force.