Controlled low-strength material incorporating recycled fine aggregate from urban red brick based construction waste

Sixteen controlled low-strength material( CLSM)mixtures with various cement-to-sand( C/Sa) ratios and water-to-solid( W/So) ratios were prepared using recycled fine aggregate from urban red brick based construction waste.The fluidity and bleeding of the fresh CLSM mixtures were measured via the modified test methods, and the hardened CLSM mixtures were then molded to evaluate their compressive strength and durability. The results showthat the fluidity of the fresh CLSM mixtures is 105 to 227 mm with the corresponding bleeding rate of 3. 7% to 15. 5%, which increases with the increase in fluidity. After aging for 28 d,the compressive strength of the hardened CLSM mixtures reaches 1. 15 to 13. 96 M Pa, and their strength can be further enhanced with longer curing ages. Additionally, the strength increases with the increase of the C/Sa ratio, and decreases with the increase of the W/So ratio under the same curing age. Based on the obtained compressive strength, a fitting model for accurately predicting the compressive strength of the CLSM mixtures was established, which takes into account the above two independent variables( C/Sa and W/So ratios).M oreover, the durability of the hardened CLSM mixtures is enhanced for samples with higher C/Sa ratios.

Performance Appraisal of Controlled Low-strength Material Using Sewage Sludge and Refuse Incineration Bottom Ash

This research evaluated the use of sewage sludge and refuse incineration bottom ash to replace calcium sulfoaluminate cement （CSA） in making controlled low-strength material （CLSM）. Various properties of CLSM mixtures were characterized in terms of unconfined compressive strength, microstructure and leachability. It was found that the strength of tested CLSM mixtures ranged from 3.6 to 9.0 MPa, over the upper excavatable limit of 2.1 MPa. The micro-structural analysis revealed that sewage sludge and bottom ash were crystallochemically in- corporated within CLSM system_s by forming the needle-like ettringite （C3A＇3CS＇_H32） with exiguous tu.bers via the typical Pozzolanic Reaction, leading to a dense and low-porosity microst;＇ucture. Furthermore,-the toxicity characteristic leaching procedure evidenced that the cumulative leachable metals in the leachate were much below the regulatory thresholds. The potential for us!ng sewage sludge and bottom ash!n CLSM makin.g was thus confirmed.

Advanced Functional Electromagnetic Shielding Materials:A Review Based on Micro‑Nano Structure Interface Control of Biomass Cell Walls

Research efforts on electromagnetic interference(EMI)shielding materials have begun to converge on green and sustainable biomass materials.These materials offer numerous advantages such as being lightweight,porous,and hierarchical.Due to their porous nature,interfacial compatibility,and electrical conductivity,biomass materials hold significant potential as EMI shielding materials.Despite concerted efforts on the EMI shielding of biomass materials have been reported,this research area is still relatively new compared to traditional EMI shielding materials.In particular,a more comprehensive study and summary of the factors influencing biomass EMI shielding materials including the pore structure adjustment,preparation process,and micro-control would be valuable.The preparation methods and characteristics of wood,bamboo,cellulose and lignin in EMI shielding field are critically discussed in this paper,and similar biomass EMI materials are summarized and analyzed.The composite methods and fillers of various biomass materials were reviewed.this paper also highlights the mechanism of EMI shielding as well as existing prospects and challenges for development trends in this field.

Effect of Carbon Dioxide (CO_2) Controlled Atmosphere on Superoxide Dismutase (SOD) Activity of Three Storage Pests in Chinese Medicinal Materials

[ Objective ] The paper was to study the effect of controlled atmosphere stress of carbon dioxide （ CO2 ） on Superoxide dismutase （SOD） activity of in- sect, so as to analyze the biological mechanism of the action of controlled atmosphere stress on insect. [ Method] Using nitrotetrazolium blue chloride （NBT） light reduction method, SOD activity of drugstore beetle （ Stegobium panlceum ）, cigarette beetle （ Lasioderma serricorne） and coffee bean beetle （Araecerus fasciculatus） was studied, and the stress response of the enzyme under controlled atmosphere stress of CO2 was analyzed. [ Result ] SOD activity of drugstore beetle, cigarette beetle and coffee bean beetle exposed to controlled atmosphere stress of high concentrations of CO2 for 3 and 6 h had certain degree of increase, and the activity sig- nificantly increased from 2.011±0.954,2.664±0.218 and 1.458±0.718 to 3. 135±0. 105,3.050±0.673 and 2.975±0.229 U/（per pest · 30 min） after treat- ment for 6 h. [ Conclusion] Controlled atmosphere stress of high concentrations of CO2 had certain activation effect on SOD activity of storage pest in Chinese me- dicinal material within the context of sub-lethal events. The results could enrich the insecticidal mechanism of controlled atmosphere and theoretical system of analy- sis on insect resistance to controlled atmosphere.

Gypsum-based Silica Gel Humidity-controlling Composite Materials:Preparation,Characterization,and Performance

Gypsum was used as substrate,and silica gel was mixed into substrate at a certain mass ratio to prepare humidity-controlling composites;moreover,the moisture absorption and desorption properties of gypsum-based composites were compared with adding different silica gel particle size and proportion.The morphological characteristics,the isothermal equilibrium moisture content curve,moisture absorption and desorption rate,moisture absorption and desorption stability,and humidity-conditioning performance were tested and analyzed.The experimental results show that,compared with pure-gypsum,the surface structure of the gypsum-based composites is relatively loose,the quantity,density and aperture of the pores in the structure increase.The absorption and desorption capacity increase along with the increase of silica gel particle size and silica gel proportion.When 3 mm silica gel particle size is added with a mass ratio of 40%,the maximum equilibrium moisture content of humidity-controlling composites is 0.161 g/g at 98% relative humidity(RH),3.22 times that of pure-gypsum.The moisture absorption and desorption rates are increased,the equilibrium moisture absorption and desorption rates are 2.68 times and 1.61 times that of pure-gypsum at 58.5% RH,respectively.The gypsum-based composites have a good stability,which has better timely response to dynamic humidity changes and can effectively regulate indoor humidity under natural conditions.

Influence of the mechanical properties of materials on the ultimate pressure-bearing capability of a pressure-preserving controller

The pressure-preserving controller is the core part of deep in-situ pressure-preserving coring(IPP-Coring) system, and its pressure-preserving capability is the key to IPP-Coring technology. To achieve a good understanding of the influence of mechanical properties of materials on the ultimate pressure-bearing capability(UPB-Capability) of the pressure-preserving controller, the IPP-Coring experimental platform was developed to test the UPB-Capability of pressure-preserving controllers of four different materials. The experimental results show that the UPB-Capability of pressure-preserving controllers with different material varies greatly. A numerical model of the pressure-preserving controller was developed to study the influences of mechanical parameters of materials on the UPB-Capability of the pressurepreserving controller after the accuracy of the numerical model is verified by experiments. The results indicate that the yield strength(YS) and Poisson's ratio(PR) of the material have little effect on the UPB-Capability of the pressure-preserving controller, whereas the elastic modulus(EM) of the material has a significant effect. A generalized model of the UPB-Capability of the pressure-preserving controller is developed to reveal the mechanism of the influence of material properties on the UPB-Capability of the pressure-preserving controllers. Considering these results, the future optimization direction of the pressure-preserving controller and material selection scheme in practical engineering applications of the pressure-preserving controller are suggested.

Synthesis of the Core-Shell Structure Materials as the Controlled-Release Drug Carrier

We have developed a controlled-release drug carrier. Smartly controlled-release polymer nanoparticles were firstly synthesized through RAFT polymerization as the controlled-release core. The structural and particle properties of polymer nanoparticles were characterized by nuclear magnetic resonance spectroscopy (1H-NMR), scanning electron microscope (SEM) and X-ray spectroscopy (EDX). Mesoporous materials were selected as the shell materials to encapsulate the smart core as the stable shell. The mesoporous shell was characterized by transmission electron microscopy (TEM) and scanning electron microscope (SEM). All the results showed that a well-defined core-shell structure with mesoporous structure was obtained, and this controllable delivery system will have the great potential in nanomedicine.

Properties of Rapid Hardening Controlled Low Strength Material Made of Recycled Fine Aggregate from Urban Red Brick Construction Waste

In some cases of emergency backfill engineering projects, traditional backfill materials cannot meet the requirements of fast construction due to their long curing time. This study presents a new kind of rapid hardening controlled low strength material, which utilizes both rapid hardening sulphoaluminate cement and recycled fine aggregate from urban red brick construction waste. Totally, sixteen mixtures were prepared for the experiment with different cement-to-sand ratios and water-to-solid ratios. The flowability and bleeding rate of fresh mixture were measured to evaluate its workability, and the compressive strength of hardened mixture was tested to evaluate its rapid hardening and mechanical properties. Test results indicate that rapid hardening controlled low strength material containing recycled fine aggregate from urban red brick construction waste can achieve the desirable flowability, but the bleeding rate increases with the increase of flowability. In addition, 2-hour compressive strength can reach 0.08 - 0.12 MPa, and 4-hour compressive strength is 0.32 - 1.54 MPa, which can meet the requirements of emergency backfill construction. At last, based on the derived compressive strength, a fitting model for predicting compressive strength evolution of this new rapid hardening backfill material is developed, which fits accurately with these experimental data.

Non-tobacco Related Materials Control Mode of Export-oriented Tobacco

Non-tobacco related materials （NTRM） come from field production, tobacco stringing, grading and purchasing, affecting cigarette quality and having potential safety hazard. The research reviewed control on NTRM from source, production and processing to enhance use efficiency of raw materials and guarantee raw material safety.

Synthesis and Modulation of Low-Dimensional Transition Metal Chalcogenide Materials via Atomic Substitution

In recent years,low-dimensional transition metal chalcogenide(TMC)materials have garnered growing research attention due to their superior electronic,optical,and catalytic properties compared to their bulk counterparts.The controllable synthesis and manipulation of these materials are crucial for tailoring their properties and unlocking their full potential in various applications.In this context,the atomic substitution method has emerged as a favorable approach.It involves the replacement of specific atoms within TMC structures with other elements and possesses the capability to regulate the compositions finely,crystal structures,and inherent properties of the resulting materials.In this review,we present a comprehensive overview on various strategies of atomic substitution employed in the synthesis of zero-dimensional,one-dimensional and two-dimensional TMC materials.The effects of substituting elements,substitution ratios,and substitution positions on the structures and morphologies of resulting material are discussed.The enhanced electrocatalytic performance and photovoltaic properties of the obtained materials are also provided,emphasizing the role of atomic substitution in achieving these advancements.Finally,challenges and future prospects in the field of atomic substitution for fabricating low-dimensional TMC materials are summarized.

Active elastic metamaterials for subwavelength wave propagation control

Recent research activities in elastic metamaterials demonstrate a significant potential for subwavelength wave propagation control owing to their interior locally resonant mechanism. The growing technological developments in electro/magnetomechanical couplings of smart materials have introduced a controlling degree of freedom for passive elastic metamaterials. Active elastic metamaterials could allow for a fine control of material physical behavior and thereby induce new functional properties that cannot be produced by passive approaches. In this paper, two types of active elastic metamaterials with shunted piezoelectric materials and electrorheological elastomers are proposed. Theoretical analyses and numerical validations of the active elastic metamaterials with detailed microstructures are pre- sented for designing adaptive applications in band gap structures and extraordinary waveguides. The active elastic metamaterial could provide a new design methodology for adaptive wave filters, high signal-to-noise sensors, and structural health monitoring applications.

Preparation and hygrothermal performance of composite phase change material wallboard with humidity control based on expanded perlite/diatomite/paraffin

Phase change material(PCM)can reduce the indoor temperature fluctuation and humidity control material can adjust relative humidity used in buildings.In this study,a kind of composite phase change material particles(CPCMPs)were prepared by vacuum impregnation method with expanded perlite(EP)as supporting material and paraffin as phase change material.Thus,a PCM plate was fabricated by mould pressing method with CPCMPs and then composite phase change humidity control wallboard(CPCHCW)was prepared by spraying the diatom mud on the surface of PCM plate.The composition,thermophysical properties and microstructure were characterized using X-ray diffraction instrument(XRD),differential scanning calorimeter(DSC)and scanning electron microscope(SEM).Additionally,the hygrothermal performance of CPCHCW was characterized by temperature and humidity collaborative test.The results can be summarized as follows:(1)CPCMPs have suitable phase change parameters with melting/freezing point of 18.23°C/29.42°C and higher latent heat of 54.66 J/g/55.63 J/g;(2)the diatom mud can control the humidity of confined space with a certain volume;(3)the combination of diatom mud and PCM plate in CPCHCW can effectively adjust the indoor temperature and humidity.The above conclusions indicate the potential of CPCHCW in the application of building energy efficiency.

Synthesis and analysis of new humidity-controlling composite materials

Gypsum is a traditional building material. To improve the humidity-controlling properties of gypsum, we prepared a new type of humidity-controlling composite using the sol-gel method. Methods to determine the maximum equilibrium moisture content and speed of adsorption/desorption were subsequently applied to analyze the performance of the samples. The appearance and structural properties of the samples were characterized by scanning electronic microscopy (SEM). The experimental results show that the humidity-controlling gel with added LiCl exhibits high moisture storage and that the equilibrium maximum moisture content is 5.652 g/g at a 75.29% relative humidity (RH). A mass ratio of LiCl/sol = 0.15 is demonstrated to be appropriate for the preparation of the new humidity-controlling composites. A coarse network with tiny pores is observed on the surface of the new humidity-controlling composites, and this pore network provides sufficient space for moisture adsorption.

Material flow control technology of ironmaking and steelmaking interface

In order to achieve higher efficient cohesion match of procedure and equipment between ironmaking and steelmaking interface, the theory of multi-dimensional material flow control was applied to analyze torpedo ladle-iron ladle transportation process between blast furnace and basic oxygen furnace. Moreover, basic parameters of material flow were analyzed and optimized, such as time, temperature and material quantity. Based on operating principles of material flow, control methods were optimized, such as product organization mode, scheduling discipline and scheduling plan of hot metal ladle. Finally, the material flow control technology of ironmaking and steelmaking interface was integrated. Satisfactory effects are obtained after applying the technology in practice. The total turnover number of torpedo ladle decreases from 20 to 18, the hot metal temperature of 1# BF torpedo ladle decreases from 36 °C to 19.5 °C, the hot metal temperature of 2# BF torpedo ladle decreases from 36.6 °C to 19.8 °C, the temperature drop of desulfurization hot metal decreases by 4 °C, and the temperature drop of non-desulfurization hot metal decreases by 2.8 °C. Furthermore, the ironmaking and steelmaking interface system will realize high-efficiency control by using this control technology.

Chemical modification of barite for improving the performance of weighting materials for water-based drilling fluids

With increasing drilling depth and large dosage of weighting materials,drilling fluids with high solid content are characterized by poor stability,high viscosity,large water loss,and thick mud cake,easier leading to reservoir damage and wellbore instability.In this paper,micronized barite(MB)was modified(mMB)by grafting with hydrophilic polymer onto the surface through the free radical polymerization to displace conventional API barite partly.The suspension stability of water-based drilling fluids(WBDFs)weighted with API barite:mMB=2:1 in 600 g was significantly enhanced compared with that with API barite/WBDFs,exhibiting the static sag factor within 0.54 and the whole stability index of 2.The viscosity and yield point reached the minimum,with a reduction of more than 40%compared with API barite only at the same density.Through multi-stage filling and dense accumulation of weighting materials and clays,filtration loss was decreased,mud cake quality was improved,and simultaneously it had great reservoir protection performance,and the permeability recovery rate reached 87%.In addition,it also effectively improved the lubricity of WBDFs.The sticking coefficient of mud cake was reduced by 53.4%,and the friction coefficient was 0.2603.Therefore,mMB can serve as a versatile additive to control the density,rheology,filtration,and stability of WBDFs weighted with API barite,thus regulating comprehensive performance and achieving reservoir protection capacity.This work opened up a new path for the productive drilling of extremely deep and intricate wells by providing an efficient method for managing the performance of high-density WBDFs.

Advances in magnetic-assisted triboelectric nanogenerators:structures,materials and self-sensing systems

Triboelectric nanogenerators(TENG),renowned for their remarkable capability to harness weak mechanical energy from the environment,have gained considerable attention owing to their cost-effectiveness,high output,and adaptability.This review provides a unique perspective by conducting a comprehensive and in-depth analysis of magnetically assisted TENGs that encompass structures,materials,and self-powered sensing systems.We systematically summarize the diverse functions of the magnetic assistance for TENGs,including system stiffness,components of the hybrid electromagnetic-triboelectric generator,transmission,and interaction forces.In the material domain,we review the incorporation of magnetic nano-composites materials,along with ferrofluid-based TENG and microstructure verification,which have also been summarized based on existing research.Furthermore,we delve into the research progress on physical quantity sensing and human-machine interface in magnetic-assisted TENGs.Our analysis highlights that magnetic assistance extends beyond the repulsive and suction forces under a magnetic field,thereby playing multifaceted roles in improving the output performance and environmental adaptability of the TENGs.Finally,we present the prevailing challenges and offer insights into the future trajectory of the magnetic-assisted TENGs development.

Smart Material Based Complex Mode Active Control of Flexible Manipulators with Kinematic Redundancy

An active control methodology is presented for suppressing the vibratoryresponse of flexible redundant manipulators with bonded piezoceramic actuators and strain gagesensors. Firstly, the dynamic equation of the manipulator is decoupled by means of the complex modetheory and the state-space expression of the controlled system is developed. Secondly, a continuouslinear quadratic regulator (LQR) state feedback controller is designed based on the minimumprinciple. Thirdly, a full-order Luenberger state observer featuring an assigned degree of stabilityis determined via the duality between control and estimation. Finally, a numerical simulation iscarried out on a planar 3R flexible redundant manipulator. The simulation results reveal that thedynamic performance of the system is improved rapidly and significantly.

Experimental Research of Electronic Devices Thermal Control Using Metallic Phase Change Materials

A Phase-change thermal control unit( PTCU) filled with metallic phase change material( PCM) Bismuth alloy for electric devices thermal protection was developed and investigated experimentally. The PTCU filled with PCM was designed and manufactured. Resistance heating components( RCHs) produced 1 W,3 W, 5 W,7W,and 10 W for simulating heat generation of electronic devices. At various heating power levels,the performance of PTCU were tested during heating period and one duty cycle period. The experimental results show that the PTCU delays RCH reaching the maximum operating temperature. Also,a numerical model was developed to enable interpretation of experimental results and to perform parametric studies. The results confirmed that the PTCU is suitable for electric devices thermal control.

A Compensation Controller Based on a Nonlinear Wavelet Neural Network for Continuous Material Processing Operations

Continuous material processing operations like printing and textiles manufacturing are conducted under highly variable conditions due to changes in the environment and/or in the materials being processed.As such,the processing parameters require robust real-time adjustment appropriate to the conditions of a nonlinear system.This paper addresses this issue by presenting a hybrid feedforward-feedback nonlinear model predictive controller for continuous material processing operations.The adaptive feedback control strategy of the controller augments the standard feedforward control to ensure improved robustness and compensation for environmental disturbances and/or parameter uncertainties.Thus,the controller can reduce the need for manual adjustments.The controller applies nonlinear generalized predictive control to generate an adaptive control signal for attaining robust performance.A wavelet-based neural network model is adopted as the prediction model with high prediction precision and time-frequency localization characteristics.Online training is utilized to predict uncertain system dynamics by tuning the wavelet neural network parameters and the controller parameters adaptively.The performance of the controller algorithm is verified by both simulation,and in a real-time practical application involving a single-input single-output double-zone sliver drafting system used in textiles manufacturing.Both the simulation and practical results demonstrate an excellent control performance in terms of the mean thickness and coefficient of variation of output slivers,which verifies the effectiveness of this approach in improving the long-term uniformity of slivers.

Modeling and Simulation of Equipment Material Inventory Control Based on System Dynamics

The paper discusses how the inventory control of army equipment material runs sytematically under the two-level maintenance system,and establishes the inventory control model based on system dynamics.On the basis of modeling and simulation,the influence of different inventory upper limit on the whole system is studied,and the optimal inventory control mechanism under the model condition is foud.In addition,through the simulation of two replenishment strategies(s,S) and(T,s,S),the advantages and disadvantages and feasibility of each replenishment strategy are analyzed.