A novel approach of tight oil reservoirs stimulation based on fracture controlling optimization and design

To deal with the stress interference caused by simultaneous propagation of multiple fractures and the wettability reversal and physical property changes of the reservoir caused by fracturing fluid getting in during large-volume fracturing of tight oil reservoirs through a horizontal well, a non-planar 3D fracture growth model was built, wettability reversal characterizing parameters and change of relative permeability curve were introduced to correct the production prediction model of fractured horizontal well, a fracturing design optimization software(Fr Smart) by integrating geological and engineering data was developed, and a fracturing design optimization approach for tight oil reservoirs based on fracture control was worked out. The adaptability of the method was analyzed and the fracture parameters of horizontal wells in tight oil reservoirs were optimized. The simulation results show that fracturing technology based on fracture control is suitable for tight oil reservoirs, and by optimizing fracture parameters, this technology makes it possible to produce the maximum amount of reserves in the well-controlled unit of unconventional reservoirs. The key points of fracturing design optimization based on fracture control include increasing lateral length of and reducing the row spacing between horizontal wells, increasing perforation clusters in one stage to decrease the spacing of neighboring fractures, and also avoiding interference of old and new fracturing wells. Field tests show that this technology can increase single well production and ultimate recovery. Using this technology in developing unconventional resources such as tight oil reservoirs in China will enhance the economics significantly.

Geological characteristics and models of fault-foldfracture body in deep tight sandstone of the second member of Upper Triassic Xujiahe Formation in Xinchang structural belt of Sichuan Basin,SW China

In the second member of the Upper Triassic Xujiahe Formation(T_(3)x_(2))in the Xinchang area,western Sichuan Basin,only a low percent of reserves has been recovered,and the geological model of gas reservoir sweet spot remains unclear.Based on a large number of core,field outcrop,test and logging-seismic data,the T_(3)x_(2) gas reservoir in the Xinchang area is examined.The concept of fault-fold-fracture body(FFFB)is proposed,and its types are recognized.The main factors controlling fracture development are identified,and the geological models of FFFB are established.FFFB refers to faults,folds and associated fractures reservoirs.According to the characteristics and genesis,FFFBs can be divided into three types:fault-fracture body,fold-fracture body,and fault-fold body.In the hanging wall of the fault,the closer to the fault,the more developed the effective fractures;the greater the fold amplitude and the closer to the fold hinge plane,the more developed the effective fractures.Two types of geological models of FFFB are established:fault-fold fracture,and matrix storage and permeability.The former can be divided into two subtypes:network fracture,and single structural fracture,and the later can be divided into three subtypes:bedding fracture,low permeability pore,and extremely low permeability pore.The process for evaluating favorable FFFB zones was formed to define favorable development targets and support the well deployment for purpose of high production.The study results provide a reference for the exploration and development of deep tight sandstone oil and gas reservoirs in China.

Fracture Plane Control in Rock Blasting

Blasting operation dissipates much of the blasting energy in crushing the rock at the borehole and the resulting cracks are randomly oriented. There is very little control of the fracture plane. In order to control the fracture plane, many methods have been applied. This paper discusses a new blasting method in which a high degree of fracture control can be achieved while minimizing the ground shock.

Control of Fracture Behavior of Carbon Fiber/Pitch-based CarbonMatrix Composites with Microspace Modification Concept

Theoretical consideration was conducted on a relation between pore diameter and interfacialarea between pores and fibers when pores uniforinly distribute in C/C composites. It was shownthat bonding at the fiber/matrix interface apparently decreased with decreasing a pore diameter,and consequently a new idea of microspace modification concept was proposed for controllingfracture behavior of C/C composites. Four types of C/C composites with various pore structureswere fabricated by hot-pressing, and their fracture behavior was investigated by three pointbending tests. The fracture behavior of the C/C composites was changed from brittle one topseudo ductile one with decreasing the pore diameter. This result supported the validity of themicrospace modification concept proposed in this paper.

PREDICTION AND CONTROL OF BOTH WRINKLE AND FRACTURE LIMITS ON CYLINDRICAL CUP MULTI DEEP DRAWING

Based on the superfluous triangle material wrinkle model,the no wrinkle limit criterion of cylindrical cup multi deep drawing is calculated as the prediction and control of the wrinkle limit.According to fracture model,the no fracture limit criterion of cylindrical cup multi deep drawing is calculated as the prediction and control of the fracture limit.Combining the no wrinkle limit criterion with the no fracture limit criterion,the no wrinkle and no fracture limit criterion and diagram on cylindrecal cup multi deep drawing are given as the prediction and control of both wrinkle and fracture limits.In accordance with this can determine the limit deep drawing coefficient and minimum deep drawing coefficient,and can choose the deep drawing coefficient of multi deep drawing,blank holder force and deformation force by optimization choice method.Theory calculation and test data are highly consistent,and suitable for no flange multi deep drawing,flange multi deep drawing and rigid punch expanding

Direct shear tests on cemented paste backfill-rock wall and cemented paste backfill-backfill interfaces

Even though a large number of large-scale arch dams with height larger than 200 m have been built in the world, the transient groundwater flow behaviors and the seepage control effects in the dam foundations under difficult geological conditions are rarely reported. This paper presents a case study on the transient groundwater flow behaviors in the rock foundation of Jinping I double-curvature arch dam, the world＇s highest dam of this type to date that has been completed. Taking into account the geological settings at the site, an inverse modeling technique utilizing the time series measurements of both hydraulic head and discharge was adopted to back-calculate the permeability of the foundation rocks,which effectively improves the uniqueness and reliability of the inverse modeling results. The transient seepage flow in the dam foundation during the reservoir impounding was then modeled with a parabolic variational inequality（PVI） method. The distribution of pore water pressure, the amount of leakage, and the performance of the seepage control system in the dam foundation during the entire impounding process were finally illustrated with the numerical results.

Formability enhancement in hot spinning of titanium alloy thin-walled tube via prediction and control of ductile fracture

The damage and fracture in hot spinning of titanium alloy is a very complex process under the combined effects of microstructure evolution and stress state.In this study,their dependences on processing parameters were investigated by an integrated FE model considering microstructure and damage evolution,and revealing the effects of microstructure and stress states on damage evolution.The results show that the inner surface of workpiece with the largest voids volume fraction is the place with the greatest potential of fracture.This is mainly attributed to the superposition effects of positive stress triaxiality and the smallest dynamic recrystallization(DRX)fraction andβphase fraction at the inner surface.The damage degree is decreased gradually with the increase of initial spinning temperature and roller fillet radius.Meanwhile,it is first decreased and then increased with the increases of spinning pass and roller feed rate,which can be explained based on the variations ofβphase fraction,DRX fraction,stress state and tensile plastic strain with processing parameters.In addition,the dominant influencing mechanisms were identified and discussed.Finally,the thickness reduction without defect in the hot spinning of TA15 alloy tube is greatly increased by proposing an optimal processing scheme.

Closed patella fracture combined with cruciate ligament injury： a case control study

Background Patellar fracture and cruciate ligament injury are a common consequence of traumatic knee injury. Patellar fracture combined with cruciate ligament injury is rarely reported, although the mechanisms of two things are similar. This study aimed to evaluate the incidence of closed patella fracture combined with cruciate ligament injury.