A kind of feed forward neural network with three layers was applied to detect conveyor belt fire faster. And backward propagation (BP) algorithm was used to train the network parameters. The appropriate parameters and...A kind of feed forward neural network with three layers was applied to detect conveyor belt fire faster. And backward propagation (BP) algorithm was used to train the network parameters. The appropriate parameters and architecture of network were ob- tained after training with 81 pair of data. Matlab was used to simulate and the experi- ment result shows training time is least and error reduces most rapidly when ten neu- rons were in hidden layer and momentum coefficient is equal to 0.95. Temperature, rate of temperature change, dense of carbon monoxide and rate of carbon monoxide dense change were considered as four parameters to detect the PVC belt fire in this paper. It is indicated that the network can give alarm as fire takes place about 350 s. The network can effectively detect the fire at the early stage of conveyor belt fire. At the same time, the reliability of alarm can be increased and the anti-interference capability can be en- hanced when using this network.展开更多
This paper studied a snow event over North China on 21 February 2017,using aircraft in-situ data,a Lagrangian analysis tool,and WRF simulations with different microphysical schemes to investigate the supercooled layer...This paper studied a snow event over North China on 21 February 2017,using aircraft in-situ data,a Lagrangian analysis tool,and WRF simulations with different microphysical schemes to investigate the supercooled layer of warm conveyor belts(WCBs).Based on the aircraft data,we found a fine vertical structure within clouds in the WCB and highlighted a 1-2 km thin supercooled liquid water layer with a maximum Liquid Water Content(LWC) exceeding0.5 g kg^(-1) during the vertical aircraft observation.Although the main features of thermodynamic profiles were essentially captured by both modeling schemes,the microphysical quantities exhibited large diversity with different microphysics schemes.The conventional Morrison two-moment scheme showed remarkable agreement with in-situ observations,both in terms of the thermodynamic structure and the supercooled liquid water layer.However,the microphysical structure of the WCB clouds,in terms of LWC and IWC,was not apparent in HUJI fast bin scheme.To reduce such uncertainty,future work may focus on improving the representation of microphysics in bin schemes with in-situ data and using similar assumptions for all schemes to isolate the impact of physics.展开更多
In underground mining,the belt is a critical component,as its state directly affects the safe and stable operation of the conveyor.Most of the existing non-contact detection methods based on machine vision can only de...In underground mining,the belt is a critical component,as its state directly affects the safe and stable operation of the conveyor.Most of the existing non-contact detection methods based on machine vision can only detect a single type of damage and they require pre-processing operations.This tends to cause a large amount of calculation and low detection precision.To solve these problems,in the work described in this paper a belt tear detection method based on a multi-class conditional deep convolutional generative adversarial network(CDCGAN)was designed.In the traditional DCGAN,the image generated by the generator has a certain degree of randomness.Here,a small number of labeled belt images are taken as conditions and added them to the generator and discriminator,so the generator can generate images with the characteristics of belt damage under the aforementioned conditions.Moreover,because the discriminator cannot identify multiple types of damage,the multi-class softmax function is used as the output function of the discriminator to output a vector of class probabilities,and it can accurately classify cracks,scratches,and tears.To avoid the features learned incompletely,skiplayer connection is adopted in the generator and discriminator.This not only can minimize the loss of features,but also improves the convergence speed.Compared with other algorithms,experimental results show that the loss value of the generator and discriminator is the least.Moreover,its convergence speed is faster,and the mean average precision of the proposed algorithm is up to 96.2%,which is at least 6%higher than that of other algorithms.展开更多
The combustion of conveyor belt is a leading factor of mine fire. In this paper, the pyrolysis properties of ordinary conveyor belt and fire-resistant belt were studied experimentally with thermo-gravimetric analysis ...The combustion of conveyor belt is a leading factor of mine fire. In this paper, the pyrolysis properties of ordinary conveyor belt and fire-resistant belt were studied experimentally with thermo-gravimetric analysis and derivative thermo-gravimetric analysis, and the curves of pyrolysis properties were achieved. On this basis, the activation energy and reaction order of pyrolysis were obtained in combination with theoretical analysis, aiming to provide data for further numerical simulation and simulating experiment of mine fire.展开更多
Ore conveyor belt rollers operate in harsh environments,making them prone to premature failure.Their service lives are highly dependent on the stress field and bearing misalignment angle,for which limit values are def...Ore conveyor belt rollers operate in harsh environments,making them prone to premature failure.Their service lives are highly dependent on the stress field and bearing misalignment angle,for which limit values are defined in a standard.In this work,an optimization methodology using metamodels based on radial basis functions is implemented to reduce themass of twomodels of rollers.From a structural point of view,one of the rollers ismade completely of metal,while the other also has some components made of polymeric material.The objective of this study is to develop and apply a parametric structural optimization methodology to minimize the mass of the two models of rollers.To represent the mechanical behavior of the rollers,simulations were performed using the finite element method.During the numerical optimization process,the variable parameters were the dimensions of the shaft and external tube.The geometric configuration that corresponded at the same time to the lowest mass and acceptable ranges for the stress and bearingmisalignment angle was determined.With the proposed methodology,a 32.3% reduction in mass was obtained for a metal roller design and an 18.9% reduction for a polymer roller.In both cases,the constraints were not violated.For the all-metal roller,the safety factors for the maximum stress and bearingmisalignment angle were 1.44 and 1.75,respectively,while for the polymer roller the corresponding figures were 1.50 and 2.23.This work describes a low-computational-cost optimization methodology for roller designs that have been little studied in the literature.Furthermore,the methodology could be adapted for use with other types of rollers and rollers made of different materials.展开更多
In order to solve the problem which may be generated in the case of manual replacement of the belt conveyor sealing leather, such as the operation space is small, the work efficiency is low and the finger is easy to b...In order to solve the problem which may be generated in the case of manual replacement of the belt conveyor sealing leather, such as the operation space is small, the work efficiency is low and the finger is easy to be scratched, Using the principle of simulated bionics, through theoretical analysis and experimental verification,a tool was designed to replace the belt conveyor sealing leather. The tool includes a limit device, feeding device,U-shaped handle three parts, suitable for the replacement of various types and sizes of belt conveyor sealing leather. Use this tool to replace the belt conveyor sealing leather, the results show that: 1) The effect of replace belt conveyor sealing leather is good, belt conveyor sealing leather flat and solid. 2) The replacement proces saveraged 1. 77 min, shorter than the original method of more than 8 min. 3) Direct contact of the fingers and the metal baffle edge was avoided, so as to reduce the chances of a finger injury.展开更多
In the period of the first twenty years after World War II the number of fires in Polish hard coal mines reached annually the value of several thousands of cases. About 80% of fires constituted spontaneous fires. Inve...In the period of the first twenty years after World War II the number of fires in Polish hard coal mines reached annually the value of several thousands of cases. About 80% of fires constituted spontaneous fires. Investigations into the development of new methods of fire hazard prediction and implementation of new methods and means of fire prevention as well as the introduction of prohibition concerning the use of products manufactured of combustible organic materials in underground mine workings re-duced considerably the hazard of underground fire rise. The worked out at the Central Mining Institute (GIG) new method of un-derground fire prediction allows the correct selection of fire prevention means. The introduction into common use of fire-resistant conveyor belts, the main factor giving rise to spontaneous fires, and methods of assessment of their fire resistance eliminated prac-tically the fire hazard. These activities contributed in an efficient way to the reduction of the number of underground fires to a sat-isfactory level.展开更多
文摘A kind of feed forward neural network with three layers was applied to detect conveyor belt fire faster. And backward propagation (BP) algorithm was used to train the network parameters. The appropriate parameters and architecture of network were ob- tained after training with 81 pair of data. Matlab was used to simulate and the experi- ment result shows training time is least and error reduces most rapidly when ten neu- rons were in hidden layer and momentum coefficient is equal to 0.95. Temperature, rate of temperature change, dense of carbon monoxide and rate of carbon monoxide dense change were considered as four parameters to detect the PVC belt fire in this paper. It is indicated that the network can give alarm as fire takes place about 350 s. The network can effectively detect the fire at the early stage of conveyor belt fire. At the same time, the reliability of alarm can be increased and the anti-interference capability can be en- hanced when using this network.
基金jointly supported by the China National Science Foundation under Grant Nos.41875172 and 42075192。
文摘This paper studied a snow event over North China on 21 February 2017,using aircraft in-situ data,a Lagrangian analysis tool,and WRF simulations with different microphysical schemes to investigate the supercooled layer of warm conveyor belts(WCBs).Based on the aircraft data,we found a fine vertical structure within clouds in the WCB and highlighted a 1-2 km thin supercooled liquid water layer with a maximum Liquid Water Content(LWC) exceeding0.5 g kg^(-1) during the vertical aircraft observation.Although the main features of thermodynamic profiles were essentially captured by both modeling schemes,the microphysical quantities exhibited large diversity with different microphysics schemes.The conventional Morrison two-moment scheme showed remarkable agreement with in-situ observations,both in terms of the thermodynamic structure and the supercooled liquid water layer.However,the microphysical structure of the WCB clouds,in terms of LWC and IWC,was not apparent in HUJI fast bin scheme.To reduce such uncertainty,future work may focus on improving the representation of microphysics in bin schemes with in-situ data and using similar assumptions for all schemes to isolate the impact of physics.
基金This work was supported by the Shanxi Province Applied Basic Research Project,China(Grant No.201901D111100).Xiaoli Hao received the grant,and the URL of the sponsors’website is http://kjt.shanxi.gov.cn/.
文摘In underground mining,the belt is a critical component,as its state directly affects the safe and stable operation of the conveyor.Most of the existing non-contact detection methods based on machine vision can only detect a single type of damage and they require pre-processing operations.This tends to cause a large amount of calculation and low detection precision.To solve these problems,in the work described in this paper a belt tear detection method based on a multi-class conditional deep convolutional generative adversarial network(CDCGAN)was designed.In the traditional DCGAN,the image generated by the generator has a certain degree of randomness.Here,a small number of labeled belt images are taken as conditions and added them to the generator and discriminator,so the generator can generate images with the characteristics of belt damage under the aforementioned conditions.Moreover,because the discriminator cannot identify multiple types of damage,the multi-class softmax function is used as the output function of the discriminator to output a vector of class probabilities,and it can accurately classify cracks,scratches,and tears.To avoid the features learned incompletely,skiplayer connection is adopted in the generator and discriminator.This not only can minimize the loss of features,but also improves the convergence speed.Compared with other algorithms,experimental results show that the loss value of the generator and discriminator is the least.Moreover,its convergence speed is faster,and the mean average precision of the proposed algorithm is up to 96.2%,which is at least 6%higher than that of other algorithms.
文摘The combustion of conveyor belt is a leading factor of mine fire. In this paper, the pyrolysis properties of ordinary conveyor belt and fire-resistant belt were studied experimentally with thermo-gravimetric analysis and derivative thermo-gravimetric analysis, and the curves of pyrolysis properties were achieved. On this basis, the activation energy and reaction order of pyrolysis were obtained in combination with theoretical analysis, aiming to provide data for further numerical simulation and simulating experiment of mine fire.
基金financed by Vale S.A.Company(www.vale.com)and the Institute of Technology Vale(ITV-www.itv.org)through the Project No.SAP 4600048682.
文摘Ore conveyor belt rollers operate in harsh environments,making them prone to premature failure.Their service lives are highly dependent on the stress field and bearing misalignment angle,for which limit values are defined in a standard.In this work,an optimization methodology using metamodels based on radial basis functions is implemented to reduce themass of twomodels of rollers.From a structural point of view,one of the rollers ismade completely of metal,while the other also has some components made of polymeric material.The objective of this study is to develop and apply a parametric structural optimization methodology to minimize the mass of the two models of rollers.To represent the mechanical behavior of the rollers,simulations were performed using the finite element method.During the numerical optimization process,the variable parameters were the dimensions of the shaft and external tube.The geometric configuration that corresponded at the same time to the lowest mass and acceptable ranges for the stress and bearingmisalignment angle was determined.With the proposed methodology,a 32.3% reduction in mass was obtained for a metal roller design and an 18.9% reduction for a polymer roller.In both cases,the constraints were not violated.For the all-metal roller,the safety factors for the maximum stress and bearingmisalignment angle were 1.44 and 1.75,respectively,while for the polymer roller the corresponding figures were 1.50 and 2.23.This work describes a low-computational-cost optimization methodology for roller designs that have been little studied in the literature.Furthermore,the methodology could be adapted for use with other types of rollers and rollers made of different materials.
文摘In order to solve the problem which may be generated in the case of manual replacement of the belt conveyor sealing leather, such as the operation space is small, the work efficiency is low and the finger is easy to be scratched, Using the principle of simulated bionics, through theoretical analysis and experimental verification,a tool was designed to replace the belt conveyor sealing leather. The tool includes a limit device, feeding device,U-shaped handle three parts, suitable for the replacement of various types and sizes of belt conveyor sealing leather. Use this tool to replace the belt conveyor sealing leather, the results show that: 1) The effect of replace belt conveyor sealing leather is good, belt conveyor sealing leather flat and solid. 2) The replacement proces saveraged 1. 77 min, shorter than the original method of more than 8 min. 3) Direct contact of the fingers and the metal baffle edge was avoided, so as to reduce the chances of a finger injury.
文摘In the period of the first twenty years after World War II the number of fires in Polish hard coal mines reached annually the value of several thousands of cases. About 80% of fires constituted spontaneous fires. Investigations into the development of new methods of fire hazard prediction and implementation of new methods and means of fire prevention as well as the introduction of prohibition concerning the use of products manufactured of combustible organic materials in underground mine workings re-duced considerably the hazard of underground fire rise. The worked out at the Central Mining Institute (GIG) new method of un-derground fire prediction allows the correct selection of fire prevention means. The introduction into common use of fire-resistant conveyor belts, the main factor giving rise to spontaneous fires, and methods of assessment of their fire resistance eliminated prac-tically the fire hazard. These activities contributed in an efficient way to the reduction of the number of underground fires to a sat-isfactory level.