Design Optimization of a Self-circulated Hydrogen Cooling System for a PM Wind Generator Based on Taguchi Method

With the continuous improvement of permanent magnet(PM)wind generators'capacity and power density,the design of reasonable and efficient cooling structures has become a focus.This paper proposes a fully enclosed self-circulating hydrogen cooling structure for a originally forced-air-cooled direct-drive PM wind generator.The proposed hydrogen cooling system uses the rotor panel supports that hold the rotor core as the radial blades,and the hydrogen flow is driven by the rotating plates to flow through the axial and radial vents to realize the efficient cooling of the generator.According to the structural parameters of the cooling system,the Taguchi method is used to decouple the structural variables.The influence of the size of each cooling structure on the heat dissipation characteristic is analyzed,and the appropriate cooling structure scheme is determined.

Microstructure and Property of Hypereutectic High Chromium Cast Iron Prepared by Slope Cooling Body-Centrifugal Casting Method

In this paper, the ring-type ingot of hypereutectic high Cr cast iron was obtained by slope cooling bodycentrifugal casting method （SC-CCM）, and its microstructure and impact toughness were investigated, respectively. The results indicated that, first, the primary carbides in the microstructure are prominently finer than those in the hypereutectic high Cr cast iron prepared by conventional casting method. Second, in the ring-type ingot, the primary carbides near radial outer field are finer than those near radial inner field; furthermore, there is dividing field in the microstructure. Finally, the impact toughness values of the specimens impacted on the radial outer face and on the radial inner face are improved respectively about 36% and 138% more than that of the hypereutectic high Cr one prepared by conventional casting method.

Effect of Cooling Methods on Methane Conversion via Dielectric-Barrier Discharges

Effects of cooling methods on stability and methane conversion rate using dielectric-barrier discharges （DBD） were systematically investigated in this article. The results showed that the methane conversion rate was as high as 44.43% in a pure methane system at a flow rate of 100 mL·min^-1 and an input power of 234.2 W with air cooling. A dark greenish and soft film-like carbon was deposited on the outer surface of quartz tube when the outer electrode was watercooled, which decreased the methane conversion. With air cooling of inner electrode the selectivity of C2 hydrocarbons was higher than that with other cooling methods, while the C3 hydrocarbons had higher selectivity with flowing water cooling. Cooling the inner electrode could restrain the carbon deposition, but would decrease the methane conversion rate. The stability of both reaction and plasma operation can be improved through cooling the reactor. From thermodynamic analysis, it was found that the effective collisions frequency among the reactant molecules and free electrons （e^-） increased with temperature, which in turn led to a higher methane conversion rate and a change in the distribution of products.

High efficient Raman sideband cooling and strong three-body recombination of atoms

We report a highly efficient three-dimensional degenerated Raman sideband cooling(3D dRSC)that enhances the loading of a magnetically levitated optical dipole trap,and observe the strong atom loss due to the three-body recombination.The 3D dRSC is implemented to obtain 5×10^(7)Cs atoms with the temperature of~480 nK.The cold temperature enables 1.8×10^(7)atoms loaded into a crossed dipole trap with an optimized excessive levitation magnetic gradient.Compared to the loading of atoms from a bare magneto-optical trap or the gray-molasses cooling,there is a significant increase in the number of atoms loaded into the optical dipole trap.We derive for the three-body recombination coefficient of L_(3)=7.73×10^(-25)cm^(6)/s by analyzing the strong atom loss at a large scattering length of 1418 Bohr radius,and discover the transition from the strong three-body loss to the dominant one-body loss.Our result indicates that the lifetime of atoms in the optical dipole trap is finally decided by the one-body loss after the initial strong three-body loss.

Numerical simulation of the preparation of semi-solid metal slurry with damper cooling tube method

In semi-solid forming process, preparing the slurry with rosette or globular microstructure is very important. A new approach named the damper cooling tube method （DCT）, to produce the semi-solid metal slurry, has been introduced. To optimize the technical parameters in designing the apparatus, the finite volume method was adopted to simulate the flow process. The temperature effects on the rheological properties of the slurries were also considered. The effects of the technical parameters on the slurry properties were studied in detail.

Experimental study on mechanical properties of granite under different cooling methods after thermal treatment

Static uniaxial compression tests were conducted on 16 granite specimens after thermal treatment using a heating device and an electro-hydraulic servo pressure-testing machine. The effects of air cooling and water cooling on the physical and mechanical properties of the high-temperature granite specimens were studied. Test results showed that the longitudinal wave velocities of the high-temperature specimens gradually decreased after they were cooled by water and air. The peak stress and elastic modulus of the samples decreased gradually with an increase in temperature, whereas their peak strain increased gradually. The effects of peak stress and peak strain were considerably more evident when cooling by water than by air. This result demonstrated that the thermal cracking of the granite specimens, and consequently, their internal micro-fractures, further developed when the specimens were cooled by water.

Thermal field in water pipe cooling concrete hydrostructures simulated with singular boundary method

The embedded water pipe system is often used as a standard cooling technique during the construction of large-scale mass concrete hydrostructures. The prediction of the temperature distribution considering the cooling effects of embedded pipes plays an essential role in the design of the structure and its cooling system. In this study, the singular boundary method, a semi-analytical meshless technique, was employed to analyze the temperature distribution. A numerical algorithm solved the transient temperature field with consideration of the effects of cooling pipe specification, isolation of heat of hydration, and ambient temperature. Numerical results are verified through comparison with those of the finite element method, demonstrating that the proposed approach is accurate in the simulation of the thermal field in concrete structures with a water cooling pipe.

Preparation of Thermosensitive Microcapsules Containing Water Soluble Powder by Melting Dispersion Cooling Method

It was tried to prepare the thermosensitive microcapsules containing the water soluble solid powder by the melting dispersion cooling method and to establish the optimum preparation conditions. As a model water soluble solid powder, sodium hydrogen carbonate was adopted in order to generate carbon dioxide gas and as a thermosensitive shell material, olefin resin with the melting point of ca. 40°C was used. In the experiment, the concentration of olefin resin in the shell material solution was mainly changed together with the concentrations of the oil soluble surfactant species and the α-tocopherol as a modifier of shell. Addition of α-tocopherol into the shell material solution could prevent the core from breaking away during the microencapsulation process and result in the higher microencapsulation efficiency, because the dispersion stability of solid powder in the shell material solution could be increased due to the increase in affinity between the shell material solution and solid powder. Also, the microencapsulation efficiency increased with the concentration of olefin resin, became maximum at 50 wt% and then, decreased. The microcapsules were found to begin melting at 36°C and to generate carbon dioxide gas.

Numerical simulation of HP rotor cooling configuration using parameterized method

This paper implemented cooling configuration design on certain gas turbine HP rotor using parameterized method.It is convenient for complicated gas turbine blade modeling using parameters and also benefit for the geometry modify in later period.Parameterized modeling is the foundation of air cooling turbine blade design method engineering application.Mesh quality can be awarded when generated complicated cooling configuration blade grids,and also the increase of calculation error can arise by many mesh blocks.Film cooling and serpentine passage can effectively enhance the cooling effectiveness and protect blade.

Influence of two-step cooling method on magnetic properties of Fe_(82)Mo_7B_(10)Cu_1 nanocrystalline alloy

Soft magnetic properties of Fe82Mo7B10Cu1 nanocrystalline alloy were studied as a function of cooling condition. The results show that higher permeability and relaxation frequency can be obtained by the two-step cooling method, and the pinning field of the sample obtained by this method is smaller than that of the furnace-cooled and water-quenched samples. This phenomenon was interpreted in terms of internal stress and the magnetic ordering of the residual amorphous phase. The two-step cooling treatment is an effective way to improve the soft magnetic properties of Fe82Mo7B10Cu1 nanocrystalline alloy.

Preparation of Microcapsules Containing Aqueous Solution of Azur B with Melting Dispersion Cooling Method and Application to DNA Amplification Detector

Microcapsules containing the aqueous solution of Azur B of a water soluble dye were prepared with the melting dispersion cooling method and applied to the amplification detector of plant DNA. Paraffin wax with melting temperature of 75°C was used as the shell material. In the experiment, the aqueous solution (W) of Azur B as the core material was dispersed in the melted paraffin wax (O) to form the (W/O) emulsion and then, the (W/O) emulsion was dispersed in the silicon oil (O’) as the continuous phase to form the (W/O)/O’ emulsion at 85°C. After formation of the (W/O)/O’ emulsion, the microcapsules were prepared by cooling the (W/O)/O’ emulsion to 50°C. The microcapsules were prepared by changing the concentration of oil soluble surfactant in the (W/O) emulsion and the volume of the (W/O) emulsion in the (W/O)/O’ emulsion. The microencapsulation efficiency increased with the concentration of oil soluble surfactant and finally became 100% under the optimum conditions. Furthermore, the microcapsules were melted down at temperature of 85°C to reveal the sharp thermal responsibility and to release the aqueous solution of Azur B. As a result, it was found that the microcapsules were able to be applied to the amplification detector of plant DNA by utilizing the reaction between DNA and Azur B.

Techno-Economic and Sustainability Analysis of Potential Cooling Methods in Irish Data Centres

11% of Irish electricity was consumed by data centres in 2020. The Irish data centre industry and the cooling methods utilised require reformative actions in the coming years to meet EU Energy policies. The resell of heat, alternative cooling methods or carbon reduction methods are all possibilities to conform to these policies. This study aims to determine the viability of the resell of waste heat from data centres both technically and economically. This was determined using a novel application of thermodynamics to determine waste heat recovery potential in Irish data centres, and the current methods of heat generation for economical comparison. This paper also explores policy surrounding waste heat recovery within the industry. The Recoverable Carnot Equivalent Power (RCEP) is theoretically calculated for the three potential cooling methods for Irish data centres. These are air, hybrid, and immersion cooling techniques. This is the maximum useable heat that can be recovered from a data centre rack. This study is established under current operating conditions which are optimised for cooling performance, that air cooling has the highest potential RCEP of 0.39 kW/rack. This is approximately 8% of the input electrical power that can be captured as useable heat. Indicating that Irish data centres have the energy potential to be heat providers in the Irish economy. This study highlighted the technical and economic aspects of prevalent cooling techniques and determined air cooling heat recovery cost can be reduced to 0.01 €/kWhth using offsetting. This is financially competitive with current heating solutions in Ireland.

Effect of cooling method on TiN precipitation behavior of high-titanium high-strength steel during solidification

Metallographic microscopy,scanning electron microscopy and TiN growth thermodynamic and kinetic equations were used to investigate the morphology,quantity,and size of TiN in the center of high-titanium high-strength steels under different solidification cooling rates.The results showed that TiN in the center of the experimental steels mainly existed in three forms:single,composite(Al2O3-TiN),and multi-particle aggregation.TiN began precipitating at around 1497℃(solidification fraction of 0.74).From the end of melting to solidification for 180 s,the cooling rates in the center of the experimental steels for furnace cooling,air cooling,refractory mold cooling,and cast iron mold cooling tended to stabilize at 0.17,0.93,1.65,and 2.15℃/s,respectively.The size of TiN in the center of the experimental steel cooled using furnace cooling was mainly concentrated in the 5-15 pm range.In contrast,the size of TiN in the center of the experimental steels cooled using air cooling,refractory mold cooling,and cast iron mold cooling were mainly concentrated in the 1-5 pm range.In addition,their density of TiN in the center of the experimental steels is signif-icantly higher than that of the furnace-cooled experimental steel.Thermodynamic and kinetic precipitation models of TiN established predicted the growth size of TiN in a high-titanium high-strength steel when the solidification cooling rates are not below 0.93℃/s.

A Comprehensive Study of a Low-Grade Heat-Driven Cooling and Power System Based on Heat Current Method

Combined cooling and power(CCP)system driven by low-grade heat is promising for improving energy efficiency.This work proposes a CCP system that integrates a regenerative organic Rankine cycle(RORC)and an absorption chiller on both driving and cooling fluid sides.The system is modeled by using the heat current method to fully consider nonlinear heat transfer and heat-work conversion constraints and resolve its behavior accurately.The off-design system simulation is performed next,showing that the fluid inlet temperatures and flow rates of cooling water as well as RORC working fluid strongly affect system performance.The off-design operation even becomes infeasible when parameters deviate from nominal values largely due to limited heat transfer capability of components,highlighting the importance of considering heat transfer constraints via heat current method.Design optimization aiming to minimize the total thermal conductance is also conducted.RORC efficiency increases by 7.9%and decreases by 12.4%after optimization,with the hot fluid inlet temperature increase from 373.15 to 403.15 K and mass flow rate ranges from 10 to 30 kg/s,emphasizing the necessity of balancing system cost and performance.

Re-reddening on Strip Surface After Water Cooling

After water cooling, there is a big temperature difference between the center and the surface of strip, which leads to the heat transfer from the center to the surface, and the surface temperature can rise in a short time. The finite element method was used to simulate the phenomena of re-reddening on the surface of strip and to analyze the temperature field of hot roiled strip during laminar cooling, and the periodical variation curve of the cooling rate was obtained during water cooling and subsequent re-reddening. The results show that the critical line of the cooling rate is at 1/3 of the half-thickness from the strip surface. The regression model of the relation of rereddening temperature, time, and distance from the surface was obtained in the re-reddening region. Re-reddening regularity on the surface of strip under the condition of different thickness and cooling rate was also studied.

Design of a Prototype EHD Air Pump for Electronic Chip Cooling Applications

This paper presents the design,optimization and fabrication of an EHD air pump intended for high-power electronic chip cooling applications.Suitable high-voltage electrode configurations were selected and studied,in terms of the characteristics of the generated electric field,which play an important role in ionic wind flow.For this purpose,dedicated software is used to implement finite element analysis.Critical design parameters,such as the electric field intensity,wind velocity,current flow and power consumption are investigated.Two different laboratory prototypes are fabricated and their performances experimentally assessed.This procedure leads to the fabrication of a final prototype,which is then tested as a replacement of a typical fan for cooling a high power density electronic chip.To assist towards that end,an experimental thermal testing setup is designed and constructed to simulate the size of a personal computer’s CPU core of variable power.The parametric study leads to the fabrication of experimental single-stage EHD pumps,the optimal design of which is capable of delivering an air flow of 51 CFM with an operating voltage of 10.5 kV.Finally,the theoretical and experimental results are evaluated and potential applications are proposed.

Analysis of the factors affecting thermal evolution of hot rolled steel during coil cooling

The thermal evolution of steel coil during cooling was simulated and investigated by the use of in-house Q-CSP software. The dependence of the thermal evolution of steel coil on cooling methods, temperature distribution of the strip before coiling, coil size and steel grades was also discussed. The study plays a significant role in helping steel makers to better understand and control the cooling process.

Exact results on cavity cooling in a system of a two-level atom and a cavity field

Using the algebraic dynamical method, this paper investigates the laser cooling of a moving two-level atom coupled to a cavity field. Analytical solutions of optical forces and the cooling temperatures are obtained. Considering Rb atoms as an example, it finds that the numerical results are relevant to the recent experimental laser cooling investigations.

Cooling simulation of plastic injection molding

Analyses the cooling of mold and plastic part during injection molding and the continued cooling of plastic part after being ejected from mold using the heat transfer theory and Boundary Element Method (BEM) to predict the temperature distribution in both mold and plastic part,and presents the experiments carried out with plates of ABS (Acrylonitrile Butadiene Styrene) to verify the validity of the cooling analysis software used to simulate the temperature distribution in ABS plate parts, and concludes that the analysis software agree qualitatively well with actual experimental findings.

AN ANALYSIS OF THE MODELING OF STRESS AND STRAIN FIELDS IN A REAL MICROSTRUC-TURE USING AHYBRID METHOD

The distribution of stress and strain fields in a micro-structuralarea of a particle reinforced composite is studied by a combinationof experimental and numerical method (hybrid method). With the ex-perimental values of displacements in a micro-region as the boundaryloading condition, strain and stress fields inside the micro-regionare calculated by the finite element method under tow different kindsof model- ing, namely, as pale stress and plane strain condition. Thedifferences between the two kinds of modeling conditions as appliedto micro-structural areas are discussed.