Preparation and characterization of molybdenum powders with copper coating by the electroless plating technique

Molybdenum powders with a diameter of approximately 3 μn were coated with copper using the electroless plating technique in the pH 12.5-13 and temperature range of 55-75℃. The optimization of the electroless copper bath was evaluated through the combination of process parameters like pH and temperature. The optimized values ofpH and temperature were found to be 12.5 and 60℃, respectively, which attributes to the bright maroon color of the coating with an increase in weight of 46%. The uncoated and coated powders were subjected to microstructural studies using scanning electron microscope （SEM） and the phases were analyzed using X-my diffrction （XRD）. An attempt was made to understand the growth mechanism of the coating. The diffusion-shrinkage autocatalytic model was suggested for copper growth on the molybdenum surface.

Measurements on the conductivity of copper coating with resonant cavity

Purpose To reduce the beam coupling impedance of the vacuum chamber made of poorly conducting material,a layer of high-conductivity metal,such as copper,is often coated on its inner surface.As the natural bunch length of modern accelerators is about several millimeters,its beam spectrum can reach tens of GHz.In this case,the skin depth of copper is of the same order of magnitude as its surface roughness,and its electrical properties can be different from that in DC,which will influence the beam coupling impedance.Therefore,the electrical property of copper coating at high frequency needs to be investigated.Methods In this paper,the method of resonant cavity is adopted to measure the coating conductivity,which is based on the relation between the quality factor of the cavity and material conductivity.Results Three different resonant modes are tested in the measurement,among which the H011 mode shows the best performance.The results also indicate that surface roughness of copper can have an influence on its effective conductivity at high frequency.Conclusion The H011 mode is suitable for measuring high-conductivity materials.When the skin depth of copper is comparable to or larger than its surface roughness,its effective conductivity will be significantly reduced.

Effect of aluminum borate whisker coating on interface and mechanical properties of 6061Al matrix composites

Copper coating was deposited on the surface of aluminum borate whisker by an electroless plating method.This method was used to modify the interfacial property of squeeze-casting aluminum borate whisker reinforced 6061Al matrix composite.Interface observation indicates that the spinel reaction(MgAl2O4) is hindered by the copper coating,and the difference in interfacial reaction degree affects the tensile property and aging behavior of the composite.For the composite with less spinel reaction(MgAl2O4),its peak-aging process are postponed due to less depletion of magnesium.On the fracture surface of copper-coated composite dimples and fractures of whiskers are more,but on the fracture surface of uncoated composite pull-out of whiskers are more than that on the coated one.In uncoated composite the fracture generally originates from the near-interface-region.

Efficiency of Aluminium and Copper Coated Aluminium Electrode in Hydrogen Fuel Generation from Rain Water

Water electrolysis is considered as the most capable and old technology for hydrogen fuel preparation. Electrolysis needs external electrical energy through electrodes to split water into hydrogen and oxygen. An efficient electrolysis requires suitable electrodes to minimize potential drop. In this study Aluminium and Copper Coated Aluminium were used as different combination of Anodes and Cathodes to find out more efficient electrodes combination. NaCl solution in rain water was taken as electrolyte. Rain water was taken to avoid ionic impedance of tap water and expenses of distilled water. In this study, the most efficient electrode combination was Copper Coated Aluminium (anode)-Aluminium (cathode) and gave the highest efficiency of hydrogen production to about 11% at normal temperature for very low concentration of NaCl (0.051 M) which increased with temperature, up to 29% upon rising of temp to 60°C. It was showed that higher concentration of electrolyte would surge the efficiency significantly. If the supplied heat could be provided from any waste heat sources then this study would be more efficient. However, current research evaluated the technical feasibility of this electrode combination for producing hydrogen with electrolysis of rain water utilizing electricity and modified electrodes.

Modified Coated Copper Wire as a New Fiber for SPME-GC Analysis of Some Polycyclic Aromatic Hydrocarbons

In this study for the first time, a novel copper Solid Phase Microextraction (SPME) fiber has been introduced for removal of naphthalene, phenanthrene and anthracene from aqueous solution. Copper was used as a solid support, which was at first coated by 3-mercaptopropyltrimethoxysi- lane. A stationary phase of oxidized multi walled carbon nanotube (MWCNTs)) was bonded to the surface of the copper wire. The developed SPME was characterized by IR and Scanning Electron Microscopy (SEM) and coupled to gas chromatography for separation of the analytes. Stability of the fiber, the effect of coating thickness and recovery time were optimized. The MWCNTs film thickness was about 5 μm which was perfect for a rapid mass transfer. The detection limits were at the range of 0.005 to 0.1 μg·L-1. The calibration curves were linear R2 > 0.9813 in the range of 0.01 to 5 μg·L-1. The method has been successfully applied for real samples with standard addition of 5 μL-1 of each sample. Stability study of the fiber to acid and alkali shows that it can be used for more than 50 times.