Continuous carbon fiber reinforced copper matrix composites with 70%(volume fraction) of carbon fibers prepared by squeeze casting technique have been used for investigation of the coefficient of thermal expansion(CTE...Continuous carbon fiber reinforced copper matrix composites with 70%(volume fraction) of carbon fibers prepared by squeeze casting technique have been used for investigation of the coefficient of thermal expansion(CTE) and thermal conductivity.Thermo-physical properties have been measured in both,longitudinal and transversal directions to the fiber orientation.The results showed that Cf/Cu composites may be a suitable candidate for heat sinks because of its good thermo-physical properties e.g.the low CTE(4.18×10-6/K) in longitudinal orientation and(14.98×10-6/K) in transversal orientation at the range of 20-50℃,a good thermal conductivity(87.2 W/m·K) in longitudinal orientation and(58.2 W/m·K) in transversal orientation.Measured CTE and thermal conductivity values are compared with those predicted by several well-known models.Eshelby model gave better results for prediction of the CTE and thermal conductivity of the unidirectional composites.展开更多
Resin matrix carbon brush composites(RMCBCs)are critical materials for high-powered electric tools.However,effectively improving their wear resistance and heat dissipation remains a challenge.RMCBCs prepared with flak...Resin matrix carbon brush composites(RMCBCs)are critical materials for high-powered electric tools.However,effectively improving their wear resistance and heat dissipation remains a challenge.RMCBCs prepared with flake graphite powders that were evenly loaded with tungsten copper composite powder(RMCBCs-W@Cu)exhibited a low wear rate of 1.63 mm^(3)/h,exhibiting 48.6%reduction in the wear rate relative to RCMBCs without additives(RMCBCs-0).In addition,RMCBCs-W@Cu achieved a low friction coefficient of 0.243 and low electric spark grade.These findings indicate that tungsten copper composite powders provide particle reinforcement and generate a gradation effect for the epoxy resin(i.e.,connecting phase)in RMCBCs,which weakens the wear of RMCBCs caused by fatigue under a cyclic current-carrying wear.展开更多
In a changing world with a high interest in new ecomaterials, natural fibers such as the steelwool or Luffa cylindriea appear in new presentations and mixing with other materials to develop better opportunities to rep...In a changing world with a high interest in new ecomaterials, natural fibers such as the steelwool or Luffa cylindriea appear in new presentations and mixing with other materials to develop better opportunities to replace synthetic fibers. This work presents a research on the use of steelwool fiber for composite materials, on the basis of the physical properties, that generate conditions of mixing with three binders （matrix） natural： the rosin, artificial hard： polyurethane resin and artificial flexible： flexible twin resin （epoxy） and finally a polyester resin to make a comparison with other major resins. A testing of compression and tension is carried out to the materials analyzed, obtaining three types of composite materials by the above mentioned binders and three proposed presentations of fiber （complete, tissue and ground）. The test tube in tension with polyester resin presented a high rigidity and a percentage of deformation of 14%, resulting in less distortion than the woven with resin polyurethane with 12% of deformation. The presentation with resin polyurethane presented greater resistance to compression, because the resin acts as a sponge absorbing the energy of charge and the join of particles is larger than the other presentations generating greater cohesion among them and avoiding its rupture easily for a load of 2,000 kg. The presentation that is least resisted was the woven in two resins in the stage of energy absorption of load where polyurethane is 800 kg and the flexible twin is 850 kg, because the form of woven fiber distribution creates spaces where there are more resin than fiber.展开更多
With the continues improving of people＇s living standards, more and more people work out in all kinds of sports fields beyond the busy work. On the other hand, the development of the modem competitive sports also req...With the continues improving of people＇s living standards, more and more people work out in all kinds of sports fields beyond the busy work. On the other hand, the development of the modem competitive sports also requires that the sports experts should not only strive for the scientific training, but should also pay much attention on the improvement and development of the sports equipment at the same time, which makes the sports equipment market have achieved unprecedented prosperity. This paper introduces the application of the fiber reinforced composite materials in the field of sports equipment, which is described mainly from the advantages of the fiber reinforced composite materials used in sports equipment areas, and from the aspects of the principles of material selection, the product varieties, the application examples and the status.展开更多
Silicon oxycarbide composites reinforced by three-dimensional braided carbon fiber （3D-B Cf/Si-O-C） were fabricated via precursor infiltration and pyrolysis of polysiloxane, and the effects of processing variables o...Silicon oxycarbide composites reinforced by three-dimensional braided carbon fiber （3D-B Cf/Si-O-C） were fabricated via precursor infiltration and pyrolysis of polysiloxane, and the effects of processing variables on mechanical properties and microstructures of 3D-B Cf/Si-O-C composites were investigated. It is found that the mechanical properties and densities of 3D-B Cf/Si-O-C composites can be increased if the first pyrolysis cycle is assisted by hot-pressing. Pyrolysis temperature has great effects on mechanical properties and microstructures of 3D-B Cf/Si-O-C composites. The composite, which is hot-pressed at 1 600 ℃ for 5 min with pressure of 10 MPa in the first pyrolysis cycle, exhibits high mechanical properties: bending strength 502 MPa and fracture toughness 23.7 MPa·m1/2. The high mechanical properties are mainly attributed to desirable interfacial structure and high density.展开更多
In this work,pitch-based carbon fibers were utilized to reinforce silicon carbide(SiC)composites via reaction melting infiltration(RMI)method by controlling the reaction temperature and resin carbon content.Thermal co...In this work,pitch-based carbon fibers were utilized to reinforce silicon carbide(SiC)composites via reaction melting infiltration(RMI)method by controlling the reaction temperature and resin carbon content.Thermal conductivities and bending strengths of composites obtained under different preparation conditions were characterized by various analytical methods.Results showed the formation of SiC whiskers(SiC_(w))during RMI process according to vapor–solid(VS)mechanism.SiC_(w) played an important role in toughening the C_(pf)/SiC composites due to crack bridging,crack deflection,and SiC_(w) pull-out.Increase in reaction temperature during RMI process led to an initial increase in thermal conductivity along in-plane and thickness directions of composites,followed by a decline.At reaction temperature of 1600℃,thermal conductivities along the in-plane and thickness directions were estimated to be 203.00 and 39.59 W/(m×K),respectively.Under these conditions,bending strength was recorded as 186.15±3.95 MPa.Increase in resin carbon content before RMI process led to the generation of more SiC matrix.Thermal conductivities along in-plane and thickness directions remained stable with desirable values of 175.79 and 38.86 W/(m×K),respectively.By comparison,optimal bending strength improved to 244.62±3.07 MPa.In sum,these findings look promising for future application of pitch-based carbon fibers for reinforcement of SiC ceramic composites.展开更多
Oxidation behaviors of carbon fiber reinforced SiC matrix composites(C/SiC)are one of the most noteworthy properties.For C/SiC,the oxidation behavior was controlled by matrix microcracks caused by the mismatch of coef...Oxidation behaviors of carbon fiber reinforced SiC matrix composites(C/SiC)are one of the most noteworthy properties.For C/SiC,the oxidation behavior was controlled by matrix microcracks caused by the mismatch of coefficients of thermal expansion(CTEs)and elastic modulus between carbon fiber and SiC matrix.In order to improve the oxidation resistance,multilayer SiC–Si_(3)N_(4) matrices were fabricated by chemical vapor infiltration(CVI)to alleviate the above two kinds of mismatch and change the local stress distribution.For the oxidation of C/SiC with multilayer matrices,matrix microcracks would be deflected at the transition layer between different layers of multilayer SiC–Si_(3)N_(4) matrix to lengthen the oxygen diffusion channels,thereby improving the oxidation resistance of C/SiC,especially at 800 and 1000℃.The strength retention ratio was increased from 61.9%(C/SiC–SiC/SiC)to 75.7%(C/SiC–Si_(3)N_(4)/SiC/SiC)and 67.8%(C/SiC–SiC/Si_(3)N_(4)/SiC)after oxidation at 800℃for 10 h.展开更多
文摘Continuous carbon fiber reinforced copper matrix composites with 70%(volume fraction) of carbon fibers prepared by squeeze casting technique have been used for investigation of the coefficient of thermal expansion(CTE) and thermal conductivity.Thermo-physical properties have been measured in both,longitudinal and transversal directions to the fiber orientation.The results showed that Cf/Cu composites may be a suitable candidate for heat sinks because of its good thermo-physical properties e.g.the low CTE(4.18×10-6/K) in longitudinal orientation and(14.98×10-6/K) in transversal orientation at the range of 20-50℃,a good thermal conductivity(87.2 W/m·K) in longitudinal orientation and(58.2 W/m·K) in transversal orientation.Measured CTE and thermal conductivity values are compared with those predicted by several well-known models.Eshelby model gave better results for prediction of the CTE and thermal conductivity of the unidirectional composites.
基金Projects(51772081,51837009,51971091)supported by the National Natural Science Foundation of ChinaProject(HFZL2018CXY003-4)supported by the Industry-University-Research Cooperation of AECC,ChinaProject(kq1902046)supported by the Major Science and Technology Projects of Changsha City,China。
文摘Resin matrix carbon brush composites(RMCBCs)are critical materials for high-powered electric tools.However,effectively improving their wear resistance and heat dissipation remains a challenge.RMCBCs prepared with flake graphite powders that were evenly loaded with tungsten copper composite powder(RMCBCs-W@Cu)exhibited a low wear rate of 1.63 mm^(3)/h,exhibiting 48.6%reduction in the wear rate relative to RCMBCs without additives(RMCBCs-0).In addition,RMCBCs-W@Cu achieved a low friction coefficient of 0.243 and low electric spark grade.These findings indicate that tungsten copper composite powders provide particle reinforcement and generate a gradation effect for the epoxy resin(i.e.,connecting phase)in RMCBCs,which weakens the wear of RMCBCs caused by fatigue under a cyclic current-carrying wear.
文摘In a changing world with a high interest in new ecomaterials, natural fibers such as the steelwool or Luffa cylindriea appear in new presentations and mixing with other materials to develop better opportunities to replace synthetic fibers. This work presents a research on the use of steelwool fiber for composite materials, on the basis of the physical properties, that generate conditions of mixing with three binders （matrix） natural： the rosin, artificial hard： polyurethane resin and artificial flexible： flexible twin resin （epoxy） and finally a polyester resin to make a comparison with other major resins. A testing of compression and tension is carried out to the materials analyzed, obtaining three types of composite materials by the above mentioned binders and three proposed presentations of fiber （complete, tissue and ground）. The test tube in tension with polyester resin presented a high rigidity and a percentage of deformation of 14%, resulting in less distortion than the woven with resin polyurethane with 12% of deformation. The presentation with resin polyurethane presented greater resistance to compression, because the resin acts as a sponge absorbing the energy of charge and the join of particles is larger than the other presentations generating greater cohesion among them and avoiding its rupture easily for a load of 2,000 kg. The presentation that is least resisted was the woven in two resins in the stage of energy absorption of load where polyurethane is 800 kg and the flexible twin is 850 kg, because the form of woven fiber distribution creates spaces where there are more resin than fiber.
文摘With the continues improving of people＇s living standards, more and more people work out in all kinds of sports fields beyond the busy work. On the other hand, the development of the modem competitive sports also requires that the sports experts should not only strive for the scientific training, but should also pay much attention on the improvement and development of the sports equipment at the same time, which makes the sports equipment market have achieved unprecedented prosperity. This paper introduces the application of the fiber reinforced composite materials in the field of sports equipment, which is described mainly from the advantages of the fiber reinforced composite materials used in sports equipment areas, and from the aspects of the principles of material selection, the product varieties, the application examples and the status.
文摘Silicon oxycarbide composites reinforced by three-dimensional braided carbon fiber （3D-B Cf/Si-O-C） were fabricated via precursor infiltration and pyrolysis of polysiloxane, and the effects of processing variables on mechanical properties and microstructures of 3D-B Cf/Si-O-C composites were investigated. It is found that the mechanical properties and densities of 3D-B Cf/Si-O-C composites can be increased if the first pyrolysis cycle is assisted by hot-pressing. Pyrolysis temperature has great effects on mechanical properties and microstructures of 3D-B Cf/Si-O-C composites. The composite, which is hot-pressed at 1 600 ℃ for 5 min with pressure of 10 MPa in the first pyrolysis cycle, exhibits high mechanical properties: bending strength 502 MPa and fracture toughness 23.7 MPa·m1/2. The high mechanical properties are mainly attributed to desirable interfacial structure and high density.
基金This work is supported by the National Key R&D Program of China(No.2018YFB1106600)the National Natural Science Foundation of China(Nos.51602257,92060202,51872229,and 51972269)+2 种基金the State Key Laboratory of Advanced Technology for Materials Synthesis and Processing(Wuhan University of Technology,No.2021-KF-10)the Creative Research Foundation of the Science and Technology on Thermostructural Composite Materials Laboratory(No.JCKYS2020607001)the Shaanxi Province Foundation for Natural Science(No.2020JQ-169).
文摘In this work,pitch-based carbon fibers were utilized to reinforce silicon carbide(SiC)composites via reaction melting infiltration(RMI)method by controlling the reaction temperature and resin carbon content.Thermal conductivities and bending strengths of composites obtained under different preparation conditions were characterized by various analytical methods.Results showed the formation of SiC whiskers(SiC_(w))during RMI process according to vapor–solid(VS)mechanism.SiC_(w) played an important role in toughening the C_(pf)/SiC composites due to crack bridging,crack deflection,and SiC_(w) pull-out.Increase in reaction temperature during RMI process led to an initial increase in thermal conductivity along in-plane and thickness directions of composites,followed by a decline.At reaction temperature of 1600℃,thermal conductivities along the in-plane and thickness directions were estimated to be 203.00 and 39.59 W/(m×K),respectively.Under these conditions,bending strength was recorded as 186.15±3.95 MPa.Increase in resin carbon content before RMI process led to the generation of more SiC matrix.Thermal conductivities along in-plane and thickness directions remained stable with desirable values of 175.79 and 38.86 W/(m×K),respectively.By comparison,optimal bending strength improved to 244.62±3.07 MPa.In sum,these findings look promising for future application of pitch-based carbon fibers for reinforcement of SiC ceramic composites.
基金This work was supported by the National Natural Science Foundation of China(Nos.52072303 and 51821091)the National Science and Technology Major Project(No.J2019-VI-0014-0129)。
文摘Oxidation behaviors of carbon fiber reinforced SiC matrix composites(C/SiC)are one of the most noteworthy properties.For C/SiC,the oxidation behavior was controlled by matrix microcracks caused by the mismatch of coefficients of thermal expansion(CTEs)and elastic modulus between carbon fiber and SiC matrix.In order to improve the oxidation resistance,multilayer SiC–Si_(3)N_(4) matrices were fabricated by chemical vapor infiltration(CVI)to alleviate the above two kinds of mismatch and change the local stress distribution.For the oxidation of C/SiC with multilayer matrices,matrix microcracks would be deflected at the transition layer between different layers of multilayer SiC–Si_(3)N_(4) matrix to lengthen the oxygen diffusion channels,thereby improving the oxidation resistance of C/SiC,especially at 800 and 1000℃.The strength retention ratio was increased from 61.9%(C/SiC–SiC/SiC)to 75.7%(C/SiC–Si_(3)N_(4)/SiC/SiC)and 67.8%(C/SiC–SiC/Si_(3)N_(4)/SiC)after oxidation at 800℃for 10 h.
