Comparison of electrochemical behaviors of Ti-5Al-2Sn-4Zr-4Mo-2Cr-1Fe and Ti-6Al-4V titanium alloys in NaNO_(3) solution

The Ti-5Al-2Sn-4Zr-4Mo-2Cr-1Fe(β-CEZ)alloy is considered as a potential structural material in the aviation industry due to its outstanding strength and corrosion resistance.Electrochemical machining(ECM)is an efficient and low-cost technology for manufacturing theβ-CEZ alloy.In ECM,the machining parameter selection and tool design are based on the electrochemical dissolution behavior of the materials.In this study,the electrochemical dissolution behaviors of theβ-CEZ and Ti-6Al-4V(TC4)alloys in NaNO3solution are discussed.The open circuit potential(OCP),Tafel polarization,potentiodynamic polarization,electrochemical impedance spectroscopy(EIS),and current efficiency curves of theβ-CEZ and TC4 alloys are analyzed.The results show that,compared to the TC4 alloy,the passivation film structure is denser and the charge transfer resistance in the dissolution process is greater for theβ-CEZ alloy.Moreover,the dissolved surface morphology of the two titanium-based alloys under different current densities are analyzed.Under low current densities,theβ-CEZ alloy surface comprises dissolution pits and dissolved products,while the TC4 alloy surface comprises a porous honeycomb structure.Under high current densities,the surface waviness of both the alloys improves and the TC4 alloy surface is flatter and smoother than theβ-CEZ alloy surface.Finally,the electrochemical dissolution models ofβ-CEZ and TC4 alloys are proposed.

Tribological Behaviors of Electroless Nickel-Boron Coating on Titanium Alloy Surface

Titanium alloys are excellent structural materials in engineering fields,but their poor tribological properties limit their further applications.Electroless plating is an effective method to enhance the tribological performance of alloys,but it is difficult to efficiently apply to titanium alloys,due to titanium alloy’s strong chemical activity.In this work,the electroless Nickel-Boron(Ni-B)coating was successfully deposited on the surface of titanium alloy(Ti-6AL-4V)via a new pre-treatment process.Then,linearly reciprocating sliding wear tests were performed to evaluate the tribological behaviors of titanium alloy and its electroless Ni-B coatings.It was found that the Ni-B coatings can decrease the wear rate of the titanium alloy from 19.89×10^(−3)mm^(3)to 0.41×10^(−3)mm^(3),which attributes to the much higher hardness of Ni-B coatings.After heat treatment,the hardness of Ni-B coating further increases corresponding to coating crystallization and hard phase formation.However,heat treatment does not improve the tribological performance of Ni-B coating,due to the fact that higher brittleness and more severe oxidative wear exacerbate the damage of heat-treated coatings.Furthermore,the Ni-B coatings heat-treated both in air and nitrogen almost present the same tribological performance.The finding of this work on electroless coating would further extend the practical applications of titanium alloys in the engineering fields.

Microstructure evolution and strengthening mechanism of high -performance powder metallurgy TA15 titanium alloy by hot rolling

Hot deformation of sintered billets by powder metallurgy(PM)is an effective preparation technique for titanium alloys,which is more significant for high-alloying alloys.In this study,Ti–6.5Al–2Zr–Mo–V(TA15)titanium alloy plates were prepared by cold press-ing sintering combined with high-temperature hot rolling.The microstructure and mechanical properties under different process paramet-ers were investigated.Optical microscope,electron backscatter diffraction,and others were applied to characterize the microstructure evolution and mechanical properties strengthening mechanism.The results showed that the chemical compositions were uniformly dif-fused without segregation during sintering,and the closing of the matrix craters was accelerated by increasing the sintering temperature.The block was hot rolled at 1200℃ with an 80%reduction under only two passes without annealing.The strength and elongation of the plate at 20–25℃ after solution and aging were 1247 MPa and 14.0%,respectively,which were increased by 24.5%and 40.0%,respect-ively,compared with the as-sintered alloy at 1300℃.The microstructure was significantly refined by continuous dynamic recrystalliza-tion,which was completed by the rotation and dislocation absorption of the substructure surrounded by low-angle grain boundaries.After hot rolling combined with heat treatment,the strength and plasticity of PM-TA15 were significantly improved,which resulted from the dense,uniform,and fine recrystallization structure and the synergistic effect of multiple slip systems.

CHIP FORMATION MODEL OF TITANIUM ALLOYS

钛合金的切屑变形从低速起就是一种典型的集中剪切滑移，这种集中剪切滑移在高速切削大部分难加工材料时是一种普遍现象。本文研究了钛合金加工的切屑形成过程并提出了描述集中剪切切屑形成过程的三阶段模型。该模型解释了集中剪切切屑节块如何启动、梯形化并最终形成锯齿形切屑。

Effect of Carburization on the Mechanical Properties of Biomedical Grade Titanium Alloys

Titanium cermets were successfully synthesized on the surface of biomedical grade titanium alloys by using sequential carburization method. The mechanical properties such as hardness, fracture toughness and plasticity were measured to estimate the potential application of titanium cermets. The results show that after carburization the surface hardness of titanium cermets was 778 HV, with a significant improvement of 128% compared with that of titanium alloys. In addition, the fracture toughness of titanium cermets was 21.5 × 10^6 Pa.m^1/2, much higher than that of other ceramics. Furthermore, the analysis of the loading-unloading curve in the nanoindentation test also indicates that the plasticity of titanium cermet reached 32.1%, a relatively high value which illustrates the combination of the metal and ceramics properties. The results suggest that sequential carburization should be an efficient way to produce titanium cermets with hard surface, high toughness and plasticity.

Reaction between Ti and boron nitride based investment shell molds used for casting titanium alloys

The aim of this paper was to study the reaction between a Ti-6Al-4V alloy and boron nitride based investment shell molds used for investment casting titanium. In BN based investment shell molds, the face coatings are made of pretreated hexagonal boron nitride （hBN） with a few yttria （Y2O3） and colloidal yttria as binder. The Ti-6Al-4V alloy was melted in a controlled atmosphere induction furnace with a segment water-cooled copper crucible. The cross-section of reaction interface between Ti alloys and shell mold was investigated by electron probe micro-analyzer （EPMA） and microhardness tester. The results show that the reaction is not serious, the thickness of the reacting layer is about 30-50 μm, and the thickness of α-case is about 180-200 pro. Moreover the α-case formation mechanism was also discussed.

Research progress of laser cladding self-fluxing alloy coatings on titanium alloys

Laser cladding is a new surface modification technology, and is widely used for fabricating wear and corrosion resistant composites coatings. Self-fluxing alloys have many advantages, such as excellent properties of deoxidizing and slagging, high wear resistance, low melting point and easy cladding, and are often used in laser cladding to improve wear and corrosion resistance of titanium and its alloys. In this paper, the recent development of Ni-based and Co-based self-fluxing alloy coatings which includes the influenee of rare earth and ceramic particles in coatings are summarized. Besides, the effects of processing parameters, such as laser power and scanning speed, on coatings are reviewed. Finally, the trend of development in the future is forecasted.

Improvement of Ductility of Powder Metallurgy Titanium Alloys by Addition of Rare Earth Element

Ti-4.5Al-6.0Mo-1.5Fe, Ti-6Al-1Mo-1Fe and Ti-6Al-4V alloys were prepared by blended elemental powder metallurgy （PM） process, and the effects of Nd on the microstructures and mechanical properties were investigated by scanning electron microscopy （SEM）, transmission electron microscopy （TEM） and X-ray diffraction （XRD）. It was found out that the addition of Nd increased the density of sintered titanium alloys slightly by a maximum increment of 1% because small amount of liquid phase occurred during sintering. The addition of Nd shows little effect on the improvement of tensile strength, while the elongation is significantly improved. For example, the elongation of Ti-4.SAl-6.0Mo-1.5Fe can be increased from 1% without addition of Nd to 13% at a Nd content of 1.2 wt pct.

A state-of-the-art review of the fabrication and characteristics of titanium and its alloys for biomedical applications

Commercially pure titanium and titanium alloys have been among the most commonly used materials for biomedical applications since the 1950 s.Due to the excellent mechanical tribological properties,corrosion resistance,biocompatibility,and antibacterial properties of titanium,it is getting much attention as a biomaterial for implants.Furthermore,titanium promotes osseointegration without any additional adhesives by physically bonding with the living bone at the implant site.These properties are crucial for producing high-strength metallic alloys for biomedical applications.Titanium alloys are manufactured into the three types ofα,β,andα+β.The scientific and clinical understanding of titanium and its potential applications,especially in the biomedical field,are still in the early stages.This review aims to establish a credible platform for the current and future roles of titanium in biomedicine.We first explore the developmental history of titanium.Then,we review the recent advancement of the utility of titanium in diverse biomedical areas,its functional properties,mechanisms of biocompatibility,host tissue responses,and various relevant antimicrobial strategies.Future research will be directed toward advanced manufacturing technologies,such as powder-based additive manufacturing,electron beam melting and laser melting deposition,as well as analyzing the effects of alloying elements on the biocompatibility,corrosion resistance,and mechanical properties of titanium.Moreover,the role of titania nanotubes in regenerative medicine and nanomedicine applications,such as localized drug delivery system,immunomodulatory agents,antibacterial agents,and hemocompatibility,is investigated,and the paper concludes with the future outlook of titanium alloys as biomaterials.

Effect of nitriding-sulfurizing composite treatment on the tribological behavior of titanium alloys

A composite layer was prepared on the surface of Ti-6Al-4V alloy by nitriding-sulfurizing composite treatment,and its microstructure and phase structure were examined by scanning electron microscopy（SEM） and X-ray diffraction（XRD）,respectively.The tribological performance was measured to investigate its dependence on the nitriding-sulfurizing composite treatment process.The results indicated that the composite layer was mainly comprised of Ti2N,TiN,and TiS2.It was found that the composite layer exhibited superior tribological properties under dry friction and absolute sliding conditions due to the formation of sulfides with self-lubricating function.

Dynamic stress–strain properties of Ti–Al–V titanium alloys with various element contents

A series of Ti–Al–V titanium alloy bars with nominal composition Ti–7Al–5V ELI,Ti–5Al–3V ELI,commercial Ti–6Al–4V ELI and commercial Ti–6Al–4V were prepared.These alloys were then heat treated to obtain bimodal or equiaxed microstructures with various contents of primary a phase.Dynamic compression properties of the alloys above were studied by split Hopkinson pressure bar system at strain rates from 2,000 to 4,000 s-1.The results show that Ti–6Al–4V alloy with equiaxed primary a(ap)volume fraction of 45 vol%or 67 vol%exhibits good dynamic properties with high dynamic strength and absorbed energy,as well as an acceptable dynamic plasticity.However,all the Ti53ELI specimens and Ti64ELI specimens with ap of 65 vol%were not fractured at a strain rate of4,000 s-1.It appears that the undamaged specimens still have load-bearing capability.Dynamic strength of Ti–Al–V alloy can be improved as the contents of elements Al,V,Fe,and O increase,while dynamic strain is not sensitive to the composition in the appropriate range.The effects of primary alpha volume fraction on the dynamic properties are dependent on the compositions of Ti–Al–V alloys.

SUPERPLASTICITY AND SOLID STATE BONDING OF TITANIUM ALLOYS

Experimental results related to solid state weldability of superplastic titanium alloys are presented. A correlation between superplastic flow and enhanced solid state weldability was established. It has been experimentally shown that a drop in the lower superplastic flow temperature with decreasing mean grain size provides an opportunity to decrease the temperature at whicmethods for titanium alloys.

Effect of graphene nanoplatelets(GNPs)addition on strength and ductility of magnesium-titanium alloys

Effect of graphene nanoplatelets(GNPs)addition on mechanical properties of magnesium–10wt%Titanium(Mg–10Ti)alloy is investigated in current work.The Mg-(10Ti+0.18GNPs)composite was synthesized using the semi powder metallurgy method followed by hot extrusion.Microstructural characterization results revealed the uniform distribution of reinforcement(Ti+GNPs)particles in the matrix,therefore(Ti+GNPs)particles act as an effective reinforcing filler to prevent the deformation.Room temperature tensile results showed that the addition of Ti+GNPs to monolithic Mg lead to increase in 0.2%yield strength(0.2%YS),ultimate tensile strength(UTS),and failure strain.Scanning Electron Microscopy(SEM),Energy-Dispersive X-ray Spectroscopy(EDS)and X-Ray Diffraction(XRD)were used to investigate the surface morphology,elemental dispersion and phase analysis,respectively.

Dissolution Characteristics of New Titanium Alloys in Electrochemical Machining

We focus on the electrochemical dissolution characteristics of new titanium alloys such as near-αtitanium alloy Ti60,α+βtitanium alloy TC4andβtitanium alloy Ti40 which are often used for aerospace industry.The experiments are carried out by electrochemical machining tool,and the surface morphology of the specimens is observed by the scanning electron microscope(SEM)and three-dimensional video microscope(DVM).The appropriate electrolyte is selected and the relationships between surface roughness and current density are achieved.The results show that the single-phase titanium alloy Ti40 has a better surface roughness after ECM compared with theα+βtitanium alloy TC4 and the near-αtitanium alloy Ti60.The best surface roughness is Ra 0.28μm when the current density is 75A/cm2.Furthermore,the surface roughness of the near-αtitanium alloy Ti60 is the most sensitive with the current density because of the different electrochemical equivalents of substitutional elements and larger grains than TC4.Finally,the suitable current density for each titanium alloy is achieved.

Development of a database system for operational use in the selection of titanium alloys

The selection of titanium alloys has become a complex decision-making task due to the growing number of creation and utilization for titanium alloys,with each having its own characteristics,advantages,and limitations.In choosing the most appropriate titanium alloys,it is very essential to offer a reasonable and intelligent service for technical engineers.One possible solution of this problem is to develop a database system（DS） to help retrieve rational proposals from different databases and information sources and analyze them to provide useful and explicit information.For this purpose,a design strategy of the fuzzy set theory is proposed,and a distributed database system is developed.Through ranking of the candidate titanium alloys,the most suitable material is determined.It is found that the selection results are in good agreement with the practical situation.

A New Aging Treatment Way for Near α High Temperature Titanium Alloys

Two near α titanium alloys, Ti-5.6Al-4.8Sn-2.0Zr-1Mo-0.35Si （1#） and Ti-6.0AI-4.8Sn-2.0Zr-1Mo-0.35Si （2#）, were solution-treated in the upper α＋β phase fields, and the duplex mixture microstructures consisting of the less volume fraction primary α phase （αp） and the transformed β phase （βt） were obtained. The aging treatments were carried out at 700℃ for 1# alloy and 760℃ for 2# alloy under varied terms, respectively. It guaranteed α2 ordered phase to precipitate only in αp but not in βt for the two alloys. The slower precipitation and growth of the α2 ordered phase and silicide was observed in 1# alloy in comparison with 2# alloy. The mechanical properties including tensile strength and ductility, the creep and lasting properties at 600℃ were investigated. Prolonging aging time did not predominantly change the tensile strength and ductility for the two alloys. The 600℃/100 h thermal exposure caused a notable decrease of tensile ductility in 2# alloy though no distinct decrease could be observed in 1# alloy after the thermal exposure. The lasting property of i# alloy was increased with prolonging aging time and finally was equal to or even better than that of 2# alloy. Nevertheless, no evident increase emerged in 2# alloy with prolonging aging time. Similarly, the creep property of 1# alloy monotonously increased with increasing aging time and finally was equal to or even better than that of 2# alloy. No evident increase could be observed for 2# alloy. It can be deduced that the overgrowth of α2 ordered phase and silicide is unable to enhance hot strength properties but cause an unacceptable damage to tensile ductility. The optimum equilibrium of the comprehensive properties depending on the proper control of α2 ordered phase and silicide can be achieved by properly selecting aging temperature and time.

Effects of Ti_(0.5)Al_(0.5)N coatings on the protecting against oxidation for titanium alloys

Ti0.5Al0.5N coatings were deposited on TC11（Ti-6.5Al-3.5Mo-1.5Zr-0.3Si） and silicon substrates using a cathode arc ion-plating system.The microstructure, composition, phase structure, and oxidation-resistance of the alloys and nitride coatings were investigated by scanning electron microscopy, X-ray diffraction, transmission electron microscopy, Auger electron spectroscopy, and thermal analyzer.The results show that the oxidation resistance of the titanium alloy is relatively limited;the compound structures of Ti mixed with Al oxides are formed during the heating process.The phases of the Ti0.5Al0.5N coatings are composed of a TiN solid solution phase.The oxidation kinetics obeys the parabolic law.During the oxidation process, the selective oxidation of Al occurs, thus protecting the underlying coating and substrate.

Progress in research on cold crucible directional solidification of titanium based alloys

Cold crucible directional solidification(CCDS)is a newly developed technique,which combines the advantages of the cold crucible and continuous melting.It can be applied to directionally solidify reactive,high purity and refractory materials.This paper describes the principle of CCDS and its characteristics;development of the measurement and numerical calculation of the magnetic field,flow field and temperature field in CCDS;and the CCDS of Ti based alloys.The paper also reviews original data obtained by some scholars,including the present authors,reported in separate publications in recent years.In Ti based alloys,Ti6Al4V,TiAl alloys and high Nb-containing TiAl alloys,have been directionally solidified in different cold crucibles.The crosssections of the cold crucibles include round,near rectangular and square with different sizes.Tensile testing results show that the elongation of directionally solidified Ti6Al4V can be improved to 12.7%from as cast5.4%.The strength and the elongation of the directionally solidified Ti47Al2Cr2Nb and Ti44Al6Nb1.0Cr2.0V are 650 MPa/3%and 602.5MPa/1.20%,respectively.The ingots after CCDS can be used to prepare turbine or engine blades,and are candidates to replace Ni super-alloy at temperatures of 700 to 900°C.

High Temperature Corrosion and Protection of Titanium Alloys and TiAl Intermetallics

High temperature corrsoion and protection of trtanium alloys and TiAl intermetallics are reviewed, andsome suggestions on the development of protective coatings are put forward.