CFD analysis of a CiADS fuel assembly during the steam generator tube rupture accident based on the LBEsteamEulerFoam

Steam generator tube rupture(SGTR) accident is an important scenario needed to be considered in the safety analysis of lead-based fast reactors. When the steam generator tube breaks close to the main pump, water vapor will enter the reactor core, resulting in a two-phase flow of heavy liquid metal and water vapor in fuel assemblies. The thermal-hydraulic problems caused by the SGTR accident may seriously threaten reactor core's safety performance. In this paper, the open-source CFD calculation software OpenFOAM was used to encapsulate the improved Euler method into the self-developed solver LBEsteamEulerFoam. By changing different heating boundary conditions and inlet coolant types, the two-phase flow in the fuel assembly with different inlet gas content was simulated under various accident conditions. The calculation results show that the water vapor may accumulate in edge and corner channels. With the increase in inlet water vapor content, outlet coolant velocity increases gradually. When the inlet water vapor content is more than 15%, the outlet coolant temperature rises sharply with strong temperature fluctuation. When the inlet water vapor content is in the range of 5–20%, the upper part of the fuel assembly will gradually accumulate to form large bubbles. Compared with the VOF method, Euler method has higher computational efficiency. However, Euler method may cause an underestimation of the void fraction, so it still needs to be calibrated with future experimental data of the two-phase flow in fuel assembly.

Serpentine Inlet Performance Enhancement Using Vortex Generator Based Flow Control

In order to provide the line-of-sight blockage of the engine face for an advanced Uninhabited Combat Air Vehicle（UCAV）, a highly curved serpentine inlet is proposed and experimentally studied. Based on the static pressure distribution measurement along the wall, the flow separation is found at the top wall of the second S duct for the baseline inlet design, which yields a high flow distortion at the exit plane. To improve the flow uniformity, a single array of vortex generators （VGs） is employed within the inlet. In this experimental study, the effects of mass flow ratio, free stream Mach number, angle of attack and yaw on the performance of a serpentine inlet instrumented with VGs are obtained. Results indicate： （1） Compared with the baseline serpentine design without flow control, the application of the VGs promotes the mixing of core flow and the low momentum flow in the boundary layer and thus prevents the flow separation. Under the design condition, the exit flow distortion （-↑△σ0） decreases from 11.7% to 2.3% by using the VGs. （2） With the descent of the free stream Mach number the total pressure loss decreases. However, the circular total pressure distortion increases. When the angle of attack rises from - 4° to 8°, the total pressure recovery and the circular total pressure distortion both go down. In addition, with the increase of yaw the total pressure recovery is fairly constant, while the circular total pressure distortion ascends gradually. （3） When Mao = 0.6-0.8, a = -4°-8° and β = 0°-6°, the total pressure recovery varies between 0.936 and 0. 961, the circular total pressure distortion coefficient varies between 1.4 % and 5.4 % and the synthesis distortion coefficient has a ranges from 3.8 % to 7.0 %. The experimental results confirm the excellent performance of the newly designed serpentine inlet incorporating VGs.

Numerical simulation of gas-liquid two-phase jet flow in air-bubble generator

Air-bubble generator is the key part of the self-inspiration type swirl flotation machines,whose flow field structure has a great effect on flotation.The multiphase volume of fluid(VOF),standard k-ε turbulent model and the SIMPLE method were chosen to simulate the present model;the first order upwind difference scheme was utilized to perform a discrete solution for momentum equation.The distributing law of the velocity,pressure,turbulent kinetic energy of every section along the flow direction of air-bubble generator was analyzed.The results indicate that the bubbles are heavily broken up in the middle cross section of throat sect and the entrance of diffuser sect along the flow direction,and the turbulent kinetic energy of diffuser sect is larger than the entrance of throat sect and mixing chamber.

A GENERALIZED LIPSCHITZ SHADOWING PROPERTY FOR FLOWS

In this paper,we define a generalized Lipschitz shadowing property for flows and prove that a flowΦgenerated by a C1vector field X on a closed Riemannian manifold M has this generalized Lipschitz shadowing property if and only if it is structurally stable.

SIMULATION OF FLUID FLOW IN CHANNEL OF A NOVEL HYDRAULIC SHOCK GENERATOR

In order to improve the engineering performance of a novel hydraulic shock generator, the fluid flow inside its complex passages is numerically investigated. The effects of the inlet flow velocity upon the turbulence intensity of the jet flow are analyzed. The calculated pressure loss is experimentally verified with the consideration of temperature determined viscosity shifting. The results are used as the reference in the further development of the hydraulic shock generator

Numerical Study on Heat Transfer and Flow Characteristics for Laminar Flow in a Circular Tube with Swirl Generators

This study investigated the heat transfer and flow characteristics of one kind of swirlgenerator in a circular heat exchanger tube through a numericalsimulation. The swirlflow induced by this type of swirlgenerator can obtain a high heat transfer rate with minimalpressure drop penalty. The simulations were carried out to understand the physicalbehavior of this kind of mesoscale heat enhancement component. By visualizing the heat transfer and flow characteristics, it is found that the swirlflow is induced by swirlgenerator in the circular tube couples with the impinging jet effect. After passing through the swirlgenerator, the localfriction factor of liquid can quickly return to lower levelmore quickly, while the localNusselt number maintains higher values for a distance; thus, the evaluation criterion of localperformance is improved. Single-factor optimization is used for three geometric parameters, i.e., the angle of swirlgenerator(25o, 45o, and 60o), the length of swirlgenerator(0.005, 0.01, and 0.02 m), and the center rod radius(1, 2, and 3 mm). The optimum parameters of the swirlgenerator for laminar flow of air in a circular tube are obtained, which should be 60o, 0.005 m, and 3 mm, respectively.

NUMERICAL STUDY OF FLOW IN CONICAL DIFFUSER WITH VORTEX GENERATOR JETS

To develop vortex generator jet （VGJ） method for flow control, the turbulence flow in a 14° conical diffuser with and without vortex generator jets are simulated by solving Navier-Stokes equations with k-ε turbulence model. The diffuser performance, based on different velocity ratio （ratio of the jet speed to the mainstream velocity）, is investigated and compared with the experimental study. On the basis of the flow characteristics using computation fluid dynamics （CFD） method observed in the conical diffuser and the downstream development of the longitudinal vortices, attempt is made to correlate the pressure recovery coefficient with the behavior of vortices produced by vortex generator jets.

A pilot study of a novel pulsatile flow generator using large collapsible bladder

Background: There are different experimental models avialable for generating pulsatile flow in laboratory and study their heamodynamic effects on blood vessels. We aim to produce a novel pulsatile flow generator utilizing a large collapsible rubber bladder and the phenomenon of fluid structure interactions occurring in a specially designed flexible tube arrangement. Mehtods: Water enters from a reservoir above into a large collapsible bladder made of rubber which opens into ‘U’ shaped tube made of flexible material and held by non rigid structures. As liquid starts flowing the distal end of collapsible bladder collapses under the negative atmospheric pressure generated inside closing the mouth of ‘U’ shaped tube and produces pulsatile flow. Resuts: The frequency of pulsations, pressure fluctuations and velocity profile resemble that of in vivo blood flow. As the flow entering into collapsible bladder increases the frequency of pulsatile flow decreases and also when height of the collapsible bladder from the ground was changed. The whole cycle of alternate collapse/expansion of collapsible bladder with generation of pulsatile flow continue indefinitely as long as there is enough water in reservoir and vertical gradient to sustain the flow. Conclusions: The pulsatile flow so produced has many of the characteristics of physiological blood flow and can be used to study mechanisms of various cardiovascular diseases in laboratory.

The Continuation Power Flow Considering Both Generator Excitation Current Limits and Armature Current Limits

在传统连续潮流算法中,发电机无功限制采用定上、下限值来处理,随着有功负荷增加,无功限值通常不变,得到的电压稳定裕度偏大。根据同步发电机的无功出力特性,提出同时计及发电机励磁电流约束和电枢电流约束的连续潮流模型和方法。当相应参数越限时,将发电机节点转换为励磁恒定模型或者电枢电流恒定模型进行计算。所提PV、PEq、PIa节点类型双向转换逻辑可在潮流迭代内进行发电机限制模式的转换,模拟实际系统无功能力的变化。分岔点类型识别模块可以识别崩溃点类型及关键约束。通过新英格兰39节点算例的仿真,证明所提算法是有效的。

Probabilistic Load Flow Algorithm with the Power Performance of Double-Fed Induction Generators

Probabilistic load flow(PLF)algorithm has been regained attention,because the large-scale wind power integration into the grid has increased the uncertainty of the stable and safe operation of the power system.The PLF algorithm is improved with introducing the power performance of double-fed induction generators(DFIGs)for wind turbines(WTs)under the constant power factor control and the constant voltage control in this paper.Firstly,the conventional Jacobian matrix of the alternating current(AC)load flow model is modified,and the probability distributions of the active and reactive powers of the DFIGs are derived by combining the power performance of the DFIGs and the Weibull distribution of wind speed.Then,the cumulants of the state variables in power grid are obtained by improved PLF model and more accurate power probability distributions.In order to generate the probability density function(PDF)of the nodal voltage,Gram-Charlier,Edgeworth and Cornish-Fisher expansions based on the cumulants are applied.Finally,the effectiveness and accuracy of the improved PLF algorithm is demonstrated in the IEEE 14-RTS system with wind power integration,compared with the results of Monte Carlo(MC)simulation using deterministic load flow calculation.

Analysis of flow instabilities in forced-convection steam generator

Because of the practical importance of two-phase instabilities, substantial efforts have been made to date to understand the physical phenomena governing such instabilities and to develop computational tools to model the dynamics. The purpose of this study is to present a numerical model for the analysis of flow-induced instabilities in forced-convection steam generator. The model is based on the assumption of homogeneous two-phase flow and ther- modynamic equilibrium of the phases. The thermal capacity of the heater wall has been included in the analysis. The model is used to analyze the flow instabilities in the steam generator and to study the effects of system pressure, mass flux, inlet temperature and inlet/outlet restriction, gap size, the ratio of do / di, and the ratio of qi / qo on the system be- havior.

Connecting Wind Turbine Generator to Distribution Power Grid--A Preload Flow Calculation Stage

A distribution grid is generally characterized by a high R/X （resistance/reactance） ratio and it is radial in nature. By design, a distribution grid system is not an active network, and it is normally designed in such a way that power flows from transmission system via distribution system to consumers. But in a situation when wind turbines are connected to the distribution grid, the power source will change from one source to two sources, in this case, network is said to be active. This may probably have an impact on the distribution grid to whenever the wind turbine is connected. The best way to know the impact of wind turbine on the distribution grid in question is by carrying out load flow analysis on that system with and without the connection of wind turbines. Two major fundamental calculations： the steady-state voltage variation at the PCC （point of common coupling） and the calculation of short-circuit power of the grid system at the POC （point of connection） are necessary before carrying out the load flow study on the distribution grid. This paper, therefore, considers these pre-load flow calculations that are necessary before carrying out load flow study on the test distribution grid. These calculations are carded out on a test distribution system.

Triboelectric–Electromagnetic Hybrid Generator for Harvesting Blue Energy

Progress has been developed in harvesting lowfrequency and irregular blue energy using a triboelectric–electromagnetic hybrid generator in recent years. However,the design of the high-efficiency, mechanically durable hybrid structure is still challenging. In this study, we report a fully packaged triboelectric–electromagnetic hybrid generator(TEHG), in which magnets were utilized as the trigger to drive contact–separation-mode triboelectric nanogenerators(CS-TENGs) and coupled with copper coils to operate rotary freestanding-mode electromagnetic generators(RF-EMGs). The magnet pairs that produce attraction were used to transfer the external mechanical energy to the CS-TENGs, and packaging of the CS-TENGpart was achieved to protect it from the ambient environment. Under a rotatory speed of 100 rpm, the CS-TENGs enabled the TEHG to deliver an output voltage, current,and average power of 315.8 V, 44.6 μA, and ~ 90.7 μW,and the output of the RF-EMGs was 0.59 V, 1.78 m A, and 79.6 μW, respectively. The cylinder-like structure made the TEHG more easily driven by water flow and demonstrated to work as a practical power source to charge commercial capacitors. It can charge a 33μF capacitor from 0 to 2.1 V in 84 s, and the stored energy in the capacitor can drive an electronic thermometer and form a self-powered water-temperature sensing system.

UNSTEADY FLOWS OF A GENERALIZED SECOND GRADE FLUID WITH THE FRACTIONAL DERIVATIVE MODEL BETWEEN TWO PARALLEL PLATES

The fractional calculus approach in the constitutive relationship model of a generalized second grade fluid is introduced.Exact analytical solutions are obtained for a class of unsteady flows for the generalized second grade fluid with the fractional derivative model between two parallel plates by using the Laplace transform and Fourier transform for fractional calculus.The unsteady flows are generated by the impulsive motion or periodic oscillation of one of the plates.In addition,the solutions of the shear stresses at the plates are also determined.

VELOCITIES OF PRECURSOR SOLITON GENERATION IN SINGLE LAYER FLOW

In this study, the moving velocitiy of precursor solitons, of the flow in depressed region, and of the zero-crossing of the trailing wavetrain relative to the moving disturbance for single-layer flow over topography were theorecticaly determined in terms of the mass and energy conservation theorems, and were examined with numerical calculations showing good agreement with theoretical results.

Numerical simulation of a self-absorbing microbubble generator for a cyclonic-static microbubble flotation column

The Cyclonic-Static Microbubble Flotation Column (FCSMC) is currently a widely used, novel type of flotation device. The self-absorbing microbubble generator is the core component of this device. The structure of the microbubble generator directly influences flotation column performance by affecting bubble size and distribution as well as gas holdup in the column. However, the complicated flow inside the generator results in high R&D costs and difficulty in testing. Thus, the CFD software, FLUENT, was used to simulate the gas-liquid two-phase flow inside a self-absorbing microbubble generator. The effect of area ratio, a key structural parameter, was studied in detail. Critical flow-field parameters including velocity, turbulent kinetic energy, minimum static pressure and gas holdup were obtained. The simulation results demonstrate that the optimum area ratio is 3.

Analytic homotopy solution of generalized three-dimensional channel flow due to uniform stretching of the plate

In this communication a generalized three- dimensional steady flow of a viscous fluid between two infinite parallel plates is considered. The flow is generated due to uniform stretching of the lower plate in x- and y-directions. It is assumed that the upper plate is uniformly porous and is subjected to constant injection. The governing system is fully coupled and nonlinear in nature. A complete analytic solution which is uniformly valid for all values of the dimensionless parameters β Re and λ is obtained by using a purely analytic technique, namely the homotopy analysis method. Also the effects of the parameters β Re and λ on the velocity field are discussed through graphs.

Exact solutions of MHD second Stokes flow of generalized Burgers fluid

This work concerns with the exact solutions of magnetohydrodynamic（MHD）flow of generalized Burgers fluid describing the second Stokes problem. The modified Darcy law is taken into account. The related velocity distribution and shear stress are expressed as a combination of steady-state and transient solutions computed by means of integral transformations. The effects of various parameters on the flow field are investigated. The MHD flow results in reduction of velocity distribution and associated thickness of the boundary layer.

The axisymmetric long-wave interfacial stability of core-annular flow of power-law fluid with surfactant

The long wave stability of core-annular flow of power-law fluids with an axial pressure gradient is investigated at low Reynolds number. The interface between the two fluids is populated with an insoluble surfactant. The analytic solution for the growth rate of perturbation is obtained with long wave approximation. We are mainly concerned with the effects of shear-thinning/thickening property and interfacial surfactant on the flow stability. The results show that the influence of shear-thinning/thickening property accounts to the change of the capillary number. For a clean interface, the shear-thinning property enhances the capillary instability when the interface is close to the pipe wall. The converse is true when the interface is close to the pipe centerline. For shear-thickening fluids, the situation is reversed. When the interface is close to the pipe centerline, the capillary instability can be restrained due to the influence of surfactant. A parameter set can be found under which the flow is linearly stable.