为了减小低快拍数和低信噪比下采样协方差矩阵误差,并降低其运算复杂度,提出了一种基于实数化的均匀圆阵采样协方差矩阵重构方法。针对均匀圆阵的特点,通过组建特殊的基向量,构成特殊的重构矩阵。通过将采样协方差矩阵实数化,进一步降...为了减小低快拍数和低信噪比下采样协方差矩阵误差,并降低其运算复杂度,提出了一种基于实数化的均匀圆阵采样协方差矩阵重构方法。针对均匀圆阵的特点,通过组建特殊的基向量,构成特殊的重构矩阵。通过将采样协方差矩阵实数化,进一步降低了重构矩阵的复杂度。考虑到多通道不一致性对重构矩阵的影响,引入0位校正算法,提高了重构方法的稳健性。最后应用重构后的协方差矩阵进行子空间类波达方向估计(direction of arrival,DOA)。实验仿真证明,该特殊重构矩阵在实数化下与原矩阵重构能力相同;当快拍数为100、信噪比为0 dB时,双信源分辨力较重构前由74%提高到95%以上;理论重构运算复杂度降低到原来的53.99%。展开更多
针对北斗三号(BeiDou-3 Navigation Satellite System,BDS-3)PPP-B2b信号精密单点定位(precise point positioning,PPP)服务可用性,以改正参数的可用性比例、平均可用卫星数和改正参数匹配性为指标进行了系统分析.结果表明:在中国及周...针对北斗三号(BeiDou-3 Navigation Satellite System,BDS-3)PPP-B2b信号精密单点定位(precise point positioning,PPP)服务可用性,以改正参数的可用性比例、平均可用卫星数和改正参数匹配性为指标进行了系统分析.结果表明:在中国及周边地区,BDS-3 PPP-B2b信号改正参数的可用性在71%~95%,且在北京地区达到最大,GPS改正参数可用性在68.5%~88.6%,差于BDS-3.中国及周边地区用户缺少PPP-B2b信号改正参数的卫星观测弧段主要集中在低高度角时段,其改正参数的可用性随着截止高度角的增大而增大;BDS-3、GPS和BDS-3/GPS在中国及周边地区的改正数可用平均卫星数分别约为8颗、7颗和15颗,可以确保有效的实时PPP(real time PPP,RT-PPP)服务性能,但平均约有1颗BDS-3卫星和2颗GPS卫星因为缺少PPP-B2b信号改正参数而无法参与RT-PPP服务;对于赤道以南地区,单个系统基本无法提供有效的PPPB2b服务,其改正参数的平均可用性低于50%,但BDS-3/GPS双系统在部分低纬度地区可提供约7~11颗的可用卫星;由于轨道改正参数和钟差改正参数更新频率不一致,在钟差改正数版本号(IOD Corr)参数更新时,会出现短暂的改正参数不匹配情况.展开更多
Number Systems are media for representing numbers;the popular ones being the Weighted Number Systems (WNS), which sometimes propagate carries during arithmetic computations. The other category, Un-Weighted Number Syst...Number Systems are media for representing numbers;the popular ones being the Weighted Number Systems (WNS), which sometimes propagate carries during arithmetic computations. The other category, Un-Weighted Number Systems, of which the Residue Number System (RNS) belongs, do not carry weights but have not yet found widespread usage in general purpose computing as a result of some challenges;one of the main challenges of RNS is overflow detection and correction. The presence of errors in calculated values due to such factors as overflow means that systems built on this number system will continue to fail until serious steps are taken to resolve the issue. In this paper, a scheme for detecting and correcting overflow during RNS addition is presented. The proposed scheme used mixed radix digits to evaluate the magnitude of the addends in order to detect the occurrence of overflow in their sum. The scheme also demonstrated a simplified technique of correcting the overflow in the event that it occurs. An analysis of the hardware requirements and speed limitations of the scheme showed that it performs considerably better in relation to similar state of art schemes.展开更多
Publisher Correction to:Financial innovation,volume 5 An error occurred during the publication of a number of articles in Financial Innovation.Several articles were published in volume 5 with a duplicate citation numb...Publisher Correction to:Financial innovation,volume 5 An error occurred during the publication of a number of articles in Financial Innovation.Several articles were published in volume 5 with a duplicate citation number.In this correction article the old and new citation metadata are published in Table 1.The original articles have been updated.The publisher apologizes for the inconvenience caused to our authors and readers.展开更多
In this paper, we present two new algorithms in residue number systems for scaling and error correction. The first algorithm is the Cyclic Property of Residue-Digit Difference (CPRDD). It is used to speed up the resid...In this paper, we present two new algorithms in residue number systems for scaling and error correction. The first algorithm is the Cyclic Property of Residue-Digit Difference (CPRDD). It is used to speed up the residue multiple error correction due to its parallel processes. The second is called the Target Race Distance (TRD). It is used to speed up residue scaling. Both of these two algorithms are used without the need for Mixed Radix Conversion (MRC) or Chinese Residue Theorem (CRT) techniques, which are time consuming and require hardware complexity. Furthermore, the residue scaling can be performed in parallel for any combination of moduli set members without using lookup tables.展开更多
Fault-tolerant data transmission models based on the redundant residue number system are proposed in this paper; they can transmit data correctly between two ends unless the residue errors exceed the error-correction ...Fault-tolerant data transmission models based on the redundant residue number system are proposed in this paper; they can transmit data correctly between two ends unless the residue errors exceed the error-correction capability. The expressions for the probability of error are presented when the channel noise is additive Gaussian noise and each branch is M-ary orthogonal signaling modulation. The expressions of the probabilities of undetected and uncorrected error are also obtained when the redundant residue number system are single error-checking and single error-correcting model, respectively.展开更多
This paper proposes a steady-state errors correction(SSEC)method for eliminating measurement errors.This method is based on the detections of error signal E(s)and output C(s)which generate an expected output R(s).In c...This paper proposes a steady-state errors correction(SSEC)method for eliminating measurement errors.This method is based on the detections of error signal E(s)and output C(s)which generate an expected output R(s).In comparison with the conventional solutions which are based on detecting the expected output R(s)and output C(s)to obtain error signal E(s),the measurement errors are eliminated even the error might be at a significant level.Moreover,it is possible that the individual debugging by regulating the coefficient K for every member of the multiple objectives achieves the optimization of the open loop gain.Therefore,this simple method can be applied to the weak coupling and multiple objectives system,which is usually controlled by complex controller.The principle of eliminating measurement errors is derived analytically,and the advantages comparing with the conventional solutions are depicted.Based on the SSEC method analysis,an application of this method for an active power filter(APF)is investigated and the effectiveness and viability of the scheme are demonstrated through the simulation and experimental verifications.展开更多
The present work adopted Reliability Centered Maintenance (RCM) methodology to evaluate marginal oilfield Early Production Facility (EPF) system to properly understand its functional failures and to develop an efficie...The present work adopted Reliability Centered Maintenance (RCM) methodology to evaluate marginal oilfield Early Production Facility (EPF) system to properly understand its functional failures and to develop an efficient maintenance strategy for the system. The outcome of the RCM conducted for a typical EPF within the Niger Delta zone of Nigeria provides an indication of equipment whose failure can significantly affect operations at the production facility. These include the steam generation unit and the wellhead choke assembly, using a risk-based failure Criticality Analysis. Failure Mode and Effect Analysis (FMEA) was conducted for the identified critical equipment on a component basis. Each component of the equipment was analyzed to identify the failure modes, causes and the effect of the failure. The outcome of the FMEA analysis aided the development of a robust maintenance management strategy, which is based on an optimized mix of corrective, preventive and condition-based monitoring maintenance for the marginal oilfield EPF.展开更多
文摘为了减小低快拍数和低信噪比下采样协方差矩阵误差,并降低其运算复杂度,提出了一种基于实数化的均匀圆阵采样协方差矩阵重构方法。针对均匀圆阵的特点,通过组建特殊的基向量,构成特殊的重构矩阵。通过将采样协方差矩阵实数化,进一步降低了重构矩阵的复杂度。考虑到多通道不一致性对重构矩阵的影响,引入0位校正算法,提高了重构方法的稳健性。最后应用重构后的协方差矩阵进行子空间类波达方向估计(direction of arrival,DOA)。实验仿真证明,该特殊重构矩阵在实数化下与原矩阵重构能力相同;当快拍数为100、信噪比为0 dB时,双信源分辨力较重构前由74%提高到95%以上;理论重构运算复杂度降低到原来的53.99%。
文摘针对北斗三号(BeiDou-3 Navigation Satellite System,BDS-3)PPP-B2b信号精密单点定位(precise point positioning,PPP)服务可用性,以改正参数的可用性比例、平均可用卫星数和改正参数匹配性为指标进行了系统分析.结果表明:在中国及周边地区,BDS-3 PPP-B2b信号改正参数的可用性在71%~95%,且在北京地区达到最大,GPS改正参数可用性在68.5%~88.6%,差于BDS-3.中国及周边地区用户缺少PPP-B2b信号改正参数的卫星观测弧段主要集中在低高度角时段,其改正参数的可用性随着截止高度角的增大而增大;BDS-3、GPS和BDS-3/GPS在中国及周边地区的改正数可用平均卫星数分别约为8颗、7颗和15颗,可以确保有效的实时PPP(real time PPP,RT-PPP)服务性能,但平均约有1颗BDS-3卫星和2颗GPS卫星因为缺少PPP-B2b信号改正参数而无法参与RT-PPP服务;对于赤道以南地区,单个系统基本无法提供有效的PPPB2b服务,其改正参数的平均可用性低于50%,但BDS-3/GPS双系统在部分低纬度地区可提供约7~11颗的可用卫星;由于轨道改正参数和钟差改正参数更新频率不一致,在钟差改正数版本号(IOD Corr)参数更新时,会出现短暂的改正参数不匹配情况.
文摘Number Systems are media for representing numbers;the popular ones being the Weighted Number Systems (WNS), which sometimes propagate carries during arithmetic computations. The other category, Un-Weighted Number Systems, of which the Residue Number System (RNS) belongs, do not carry weights but have not yet found widespread usage in general purpose computing as a result of some challenges;one of the main challenges of RNS is overflow detection and correction. The presence of errors in calculated values due to such factors as overflow means that systems built on this number system will continue to fail until serious steps are taken to resolve the issue. In this paper, a scheme for detecting and correcting overflow during RNS addition is presented. The proposed scheme used mixed radix digits to evaluate the magnitude of the addends in order to detect the occurrence of overflow in their sum. The scheme also demonstrated a simplified technique of correcting the overflow in the event that it occurs. An analysis of the hardware requirements and speed limitations of the scheme showed that it performs considerably better in relation to similar state of art schemes.
文摘Publisher Correction to:Financial innovation,volume 5 An error occurred during the publication of a number of articles in Financial Innovation.Several articles were published in volume 5 with a duplicate citation number.In this correction article the old and new citation metadata are published in Table 1.The original articles have been updated.The publisher apologizes for the inconvenience caused to our authors and readers.
文摘In this paper, we present two new algorithms in residue number systems for scaling and error correction. The first algorithm is the Cyclic Property of Residue-Digit Difference (CPRDD). It is used to speed up the residue multiple error correction due to its parallel processes. The second is called the Target Race Distance (TRD). It is used to speed up residue scaling. Both of these two algorithms are used without the need for Mixed Radix Conversion (MRC) or Chinese Residue Theorem (CRT) techniques, which are time consuming and require hardware complexity. Furthermore, the residue scaling can be performed in parallel for any combination of moduli set members without using lookup tables.
基金Supported by the National Natural Science Foundation of China
文摘Fault-tolerant data transmission models based on the redundant residue number system are proposed in this paper; they can transmit data correctly between two ends unless the residue errors exceed the error-correction capability. The expressions for the probability of error are presented when the channel noise is additive Gaussian noise and each branch is M-ary orthogonal signaling modulation. The expressions of the probabilities of undetected and uncorrected error are also obtained when the redundant residue number system are single error-checking and single error-correcting model, respectively.
基金National Natural Science Foundation of China(No.61273172)
文摘This paper proposes a steady-state errors correction(SSEC)method for eliminating measurement errors.This method is based on the detections of error signal E(s)and output C(s)which generate an expected output R(s).In comparison with the conventional solutions which are based on detecting the expected output R(s)and output C(s)to obtain error signal E(s),the measurement errors are eliminated even the error might be at a significant level.Moreover,it is possible that the individual debugging by regulating the coefficient K for every member of the multiple objectives achieves the optimization of the open loop gain.Therefore,this simple method can be applied to the weak coupling and multiple objectives system,which is usually controlled by complex controller.The principle of eliminating measurement errors is derived analytically,and the advantages comparing with the conventional solutions are depicted.Based on the SSEC method analysis,an application of this method for an active power filter(APF)is investigated and the effectiveness and viability of the scheme are demonstrated through the simulation and experimental verifications.
文摘The present work adopted Reliability Centered Maintenance (RCM) methodology to evaluate marginal oilfield Early Production Facility (EPF) system to properly understand its functional failures and to develop an efficient maintenance strategy for the system. The outcome of the RCM conducted for a typical EPF within the Niger Delta zone of Nigeria provides an indication of equipment whose failure can significantly affect operations at the production facility. These include the steam generation unit and the wellhead choke assembly, using a risk-based failure Criticality Analysis. Failure Mode and Effect Analysis (FMEA) was conducted for the identified critical equipment on a component basis. Each component of the equipment was analyzed to identify the failure modes, causes and the effect of the failure. The outcome of the FMEA analysis aided the development of a robust maintenance management strategy, which is based on an optimized mix of corrective, preventive and condition-based monitoring maintenance for the marginal oilfield EPF.
