Experimental Study on Fatigue Performance of Reinforced Concrete Beams in Corrosive Environment with Cyclic Loads

In marine environments,reinforced concrete bridge structures are sub-jected to cyclic loads and chloride ingress,which results in corrosion of the rein-forcing bars,early deterioration,durability loss,and a considerable reduction in the fatigue strength.Owing to the complexity of the problem and the difficulty of testing,there are few studies on the fatigue performance of concrete structures under the combined action of corrosion environment and cyclic load.Therefore,a coupling test device for corrosion and cyclic load is designed and fatigue tests of reinforced concrete beams in air environments and chlorine salt corrosive envir-onments are carried out.The fatigue corrosion process,damage mode,and corro-sion features of the test beams as well as chloride ion content in concrete are analyzed.The relationships of deflection,crack,and number of cycles in the dif-ferent environments are given.Results show that the fatigue life of the beam is.greatly reduced under coupled effects of the cyclic load and corrosive environ-ment,the failure fom of the beam is corrosion fatigue damage.The deflection and crack keeps growing with the increase in loading cycles.Under the coupling of cyclic load and corrosion env ironment,the content of chloride ion in concrete is low and there is less variety along the direction of penetration.

Review on Stress Corrosion and Corrosion Fatigue Failure of Centrifugal Compressor Impeller

Corrosion failure,especially stress corrosion cracking and corrosion fatigue,is the main cause of centrifugal compressor impeller failure.And it is concealed and destructive.This paper summarizes the main theories of stress corrosion cracking and corrosion fatigue and its latest developments,and it also points out that existing stress corrosion cracking theories can be reduced to the anodic dissolution（AD）,the hydrogen-induced cracking（HIC）,and the combined AD and HIC mechanisms.The corrosion behavior and the mechanism of corrosion fatigue in the crack propagation stage are similar to stress corrosion cracking.The effects of stress ratio,loading frequency,and corrosive medium on the corrosion fatigue crack propagation rate are analyzed and summarized.The corrosion behavior and the mechanism of stress corrosion cracking and corrosion fatigue in corrosive environments,which contain sulfide,chlorides,and carbonate,are analyzed.The working environments of the centrifugal compressor impeller show the behavior and the mechanism of stress corrosion cracking and corrosion fatigue in different corrosive environments.The current research methods for centrifugal compressor impeller corrosion failure are analyzed.Physical analysis,numerical simulation,and the fluid-structure interaction method play an increasingly important role in the research on impeller deformation and stress distribution caused by the joint action of aerodynamic load and centrifugal load.

EFFECTS OF STRESS RATIO AND FREQUENCY ON CORROSION FATIGUE CRACK GROWTH MECHANISM IN LOW ALLOY STEELS

Based on theoretical analysis about local strain,strain rate and dissolving rate at crack tip, the corrosion fatigue crack growth rate of steels ZG20SiMn and SM50B-Zc in fresh water and 3.5% NaCl solution were measured experimentally,and the PH and electrode potential within crack were also measured continuously along with crack propagating.It showed that the increase of crack growth rate,caused by both decreasing frequency and raising stress ratio,was mainly accelerated by hydrogen embrittlement.

EFFECT OF POTENTIAL ON INTERACTION BETWEEN STRESS CORROSION CRACKING AND CORROSION FATIGUE OF AUSTENITIC STAINLESS STEEL IN BOILING 42% MgCl_2 SOLUTION

The environment-sensitive fracture behaviour of 0Cr18Ni9Ti austenitic stainless steel in boiling 42% MgCl_2 under the specific load of low frequency and high mean stress was inves- tigated from the relations and differences of crack growth rates and fractographs between stress corrosion fatigue and stress corrosion cracking.The interaction between stress corro- sion cracking and corrosion fatigue was also studied from fracture characteristics with empha- sis on the effects of applied potential on the interaction.

Corrosion and Fatigue Testing of Microsized 304 Stainless Steel Beams Fabricated by Femtosecond Laser

The 304 stainless steel （SS） microcantilever specimens with dimensions of 30 #m ×30 #m ×50 #m （thicknessx width × length） were fabricated by femtosecond （fs） laser. The microsized cantilevers of good quality with structure and dimensions according commendably with that of the designed cantilever were obtained. The result shows that fs laser micromachining is a promising method for directly fabricating metallic microcomponents. Corrosion and fatigue properties of microsized specimens were carried out on the microsized 304 SS cantilever beams by a newly developed fatigue testing machine. The results show that the microsized 304 SS specimens appear to have an improved resistance towards localized corrosion compared to ordinary-sized 304 SS specimens after the static corrosion testing. The testing result shows that the presence of corrosive solution reduces the fatigue lifetime of the 304 SS specimen by a factor of 10-100. The maximum bending loads measured by fatigue testing machine decrease rapidly at the terminal stage of environment assisted fatigue testing. Corrosion fracture first occurred at the range of notch with a higher tensile bending stress, and exhibited clear evidence of trans-columnar fracture detected by SEM （scanning electron microscopy）.

Corrosion fatigue of the extruded Mg-Zn-Y-Nd alloy in simulated body fluid

Magnesium alloys were considered to be used as biodegradable implants due to their biocompatibility,biodegradability and nontoxicity.However,under the simultaneous action of corrosive environment and mechanical loading in human body,magnesium alloys are easy to be affected by corrosion fatigue and stress corrosion cracking.In this work,the fatigue behavior of the extruded Mg-Zn-Y-Nd alloy used for vascular stents was studied both in air and in simulated body fluid(SBF).It was revealed that the fatigue limit of as-extruded Mg-Zn-Y-Nd alloy in air is about 65 MPa at 10^7 cycles,while there is no limit in SBF and shows a linear relationship between the fatigue life and stress amplitudes.The fatigue crack source in air was formed by the inclusions and defects.However,the stress corrosion and hydrogen embrittlement are the main reasons for the formation of the fatigue initial crack source in SBF.

INFLUENCE OF APPLIED POTENTIAL AND LOADING WAVEFORM ON FATIGUE CRACK GROWTH FOR STEEL A537 IN 3.5% NaCl SOLUTION

Influence of applied potentials and loading waveform on the fatigue crack growth for steel A537 in 3.5% NaCl solution,and corresponding straining electrode behaviour have been studied.Under the applied potentials over or below -800mV(SCE),the anodic dissolution or the hydrogen embrittlement is predominatant,respectively.For applied anodic potential,the acceleration effect of continuous loading pattern on the CF crack growth mainly appeared at the range of low ΔK values,while for cathodic potential,it appeared at the high ΔK values.The continuous straining causes a decrease of natural potential and an increase of anodic dissolution current.

EFFECT OF MICROSTRUCTURE ON CORROSION FATIGUE BEHAVIOUR OF A LOW CARBON BAINITE STEEL

The behaviour towards corrosion fatigue of low carbon bainite steel with various microstructures after tempered at different temperatures has been examined. The susceptibility of the steel to corrosion fatigue may be improved by tempering at 300℃.

EFFECIS OF TEMPERATURE AND OVERLOAD RETARDATION ON CORROSION FATIGUE CRACK GROWTH OF HIGH STRENGTH STEEL

The fatigue crack growth rate (CGR) of ultra high strength steel 30CrMnSiNi2A in distilled water at 18,35 and 55℃ were measured.It was confirmed that the temperature is strongly af- fected on the corrosion fatigue CGR of ultra high strength steel.An expression concerning the effects of Δ K and temperature on the CGR was proposed.The fact that the apparent activation energy (36.6 kJ/mol) resulted from regressive analysis of CGR data was similar to the activation energy of hydrogen diffusion in γ-Fe,strongly supporting the theory of hydrogen-assisted crack growth.The overload retardation effect was greatly reduced in cor- rosion fatigue crack growth,especially at lower frequency,e.g.,0.1 Hz.This phenomenon might be due to the increase of the SCC component of CGR after an overload.

The Corrosion Fatigue Properties of High Performance Concrete

With the loading test equipment of corrosion fatigue specially designed, the corrosion fatigue characteristics of high performance concrete (HPC) withstanding the interaction of third point fatigue loading and Na_2SO_4 solution were investigated and analyzed. The experimental results indicate that water-binder ratio evidently influences the corrosion fatigue characteristics of HPC, and a moderate quantitative fine mineral admixture enhances the corrosion fatigue resistance of HPC. The effect is more significant when fly ash and silica fume are added.

Corrosion fatigue behavior of fastening hole structure and virtual crack propagation tests

The fatigue crack propagation behavior of the LY12CZ aluminum alloy fastener involving a central hole in air or in 3.5wt% NaCl solution was investigated. The experimental results indicated that the corrosion fatigue crack growth rate decreased with the increasing loading frequency,and in a corrosive environment,the crack growth rate was slightly larger than that in air. Based on the experimental results,the virtual corrosion fatigue crack propagation tests were investigated and the stochastic process method and the AFGROW simulation method were presented. The normal process and lognormal process were considered for the stochastic process method based on the numerically fitted Paris equation. The distribution of crack size and the corresponding probabilistic model of crack length distribution for a given number of cycles can be found by integrating the stochastic process over time. Using the AFGROW software,the virtual simulation was carried out to analyze the corrosion fatigue crack growth behavior and the predicted crack growth curve was in good agreement with the experimental results.

Corrosion Fatigue Behavior of Duplex Stainless Steel in 3.5% Sodium Chloride Solution

The corrosion fatigue behavior of duplex stainless steel (DSS) was studied at different cyclic stress levels in 3.5%NaCl (mass fraction, so as the follows) solution (pH=7) at 50 degreesC. The results showed that DSS was susceptible to pitting corrosion and corrosion fatigue. Both intergranluar corrosion cracking and transgranlular corrosion cracking initiated at the bottom of pitting holes. Furthermore, the corrosion fatigue properties of DSS in 3.5%NaCl solution may be relatived to complex electrochemical and mechanical coupling effects between the three phases (austenite, ferrite and martensite), where martensite and ferrite were anodic in the corrosion cell and could be prone to cracking under certain condition.

Effect of Thermal Shock Process in Accelerated Environment Spectrum on the Fatigue Life of 7B04-T6 Aluminum Alloy

The effect of thermal shock, in an accelerated-corrosion environment spectrum, on the fatigue and corrosion behavior of 7B04-T6 aluminum alloy, was determined. The environment spectrum consists of two modules, namely： salt-spray corrosion and thermal shock. The effect of thermal shock on the mechanical properties was determined via tensile tests; SEM, DCS, and XRD were used to determine the effect of thermal shock on the corrosion products. In addition, the corrosion resistance of the products was ascertained through electrochemical testing. The results show that the mechanical properties and fatigue life of the aluminum alloy will decline with prolonged thermal shock time. The thermal shock process may result in denser surface corrosion products than those formed on the no thermal shock specimens, and transformation of some Al（OH）_3 into Al OOH. Al OOH may have resulted in improved corrosion resistance and hence a lower decrease in the fatigue life after corrosion, compared with that of the no thermal shock specimen. Repeated corrosion/thermal shock may have delayed further decease in the fatigue life. Therefore, selection of an appropriate equivalent thermal shock temperature and time was essential for designing the environmental spectrum.

Seawater Corrosion Fatigue of Welded Joints Under Random Variable Amplitude Loading

Offshore platforms are always subjected to wave action which is random variable amplitude cyclic loading. In order to simulate the stressing condition at the 'hot spot' of the tubular joints and the marine environment, random variable amplitude fatigue tests have been carried out on welded plate joints in sea water. The tests have been conducted under the conditions of loading frequency of 0.2 Hz/, stress ratio of -1, seawater temperature of about 20°C and cathodic protection with the potential about -850 mV, SCE. The test results have been compared with the seawater corrosion fatigue life under constant amplitude loading. Miner's linear cumulative damage summation rule has been used to predict the corrosion fatigue life under variable amplitude loading. The predicted life is in good agreement with the test data.

EFFECTS OF HEAT TREATMENT AND ENVIRONMENT ON CRACK PROPAGATION RATE IN STEEL GC-4 UNDER CORROSION FATIGUE AND STRESS CORROSION

Comparative investigations were carried out of the effect of heat treatment regimes Jor steel GC-4(40CrMnSiMoVA)on its crack propagating rates,from corrosion fatigue, (da/dN)_(CF),or stress corrosion cracking,(da/dt)_(SCC),in media with various constituents and pH values.Both(da/dN)_(CF) and(da/dt)_(SCC) accelerate with the increase of yield stress of the steel,yet the former is far less than the later.In comparison with media,the (da/dt)_(SCC) in distilled water is slightly greater than that in 3.5% NaCl solution,and the (da/dN)_(CF) in distilled water is far less than that in 3.5% NaCl solution.With the pH value increasing in 3.5% NaCl solution,the(da/dN)_(CF) lowers down and the(da/dt)_(SCC) speeds up.An explanation was also proposed with concept of the cyclic hardening and softening at crack tip,as well as the crack closure and occluded cell effect.

Saturation Dislocation Microstructures of Double-slip-oriented Copper Single Crystal during the Corrosion Fatigue in a 0.5 mol/L NaCl Aqueous Solution

Copper single crystal specimens with the longitudinal axis parallel to the [013] double-slip-orientation were grown through Bridgman technique. The fatigue tests were performed using a symmetric tension-compression load mode at room temperature in an open-air and a 0.5 mol/L NaCl solution, respectively. The dislocation microstructures were observed with scanning electron microscopy (SEM) by the electron channeling contrast (ECC) and transmission electron microscopy (TEM). The results show that the saturation dislocation microstructures during the corrosion fatigue in the aqueous solution of 0.5 mol/L NaCI, mainly consisted of labyrinth, wall and vein dislocation structures, which differs from the dislocation structures of the walls and veins in an open-air environment.

CORROSION FATIGUE CRACK GROWTH OF MEDIUM STRENGTH STEEL HT60 IN SYNTHETIC SEA WATER

The corrosion fatigue crack growth and near-threshold characteristics of a medium strength steel HT60 were investigated using compact tension specimens exposed to synthetic sea water. The da/dN-△AK_(eff) relation in air can give a conservative estimation of da/dN-△K relations in sea water. In the case of high R, however, crack growth acceleration at high △K regions appears to be cantrolled by the stress-assisted dissolution. The crack opening stress inlensity factor K_(op) detected by the back-face-strain method is the result of crack surface in contact with the corrosion products and therefore an overestimated value of K_(op) at the crack tip is given.

CORROSION FATIGUE BEHAVIOR OF STAINLESS STEEL 3RE60 IN 3.5% SODIUM CHLORIDE SOLUTION

The corrosion fatigue behavior of stainless steel 3RE60 in 3.5%NaCl solution was studied at different cyclic stress levels. The results showed that both intergranular corrosion cracking and transgranular corrosion cracking initiated at the bottom of pits. The corrosion fatigue behavior of 3RE60 may be related to complex electrochemical and mechanical coupling effects between the three phases (austenite, ferrite and martensite), where martensite and ferrite were anodic in the corrosion cell and could be prone to crack under certain conditions.

CORROSION FATIGUE CRACK INITIATION BEHAVIOR OF 316L STAINLESS STEEL IN HANK’S SOLUTION

This paper investigates the corrosion fatigue (CF) crack initiation behavior of 316L stainless steel in Hank's solution which simulates bodylike fluid. The CF experiments were conducted under the conditions of electrochemically accelerated, free immersion and pre-polarized pitting potential. The results showed that 316L stainless steel was susceptible to pitting corrosion in Hank's solution. Intergranular corrosion occurred obviously at the bottom of pits where the CF cracks initiated by the combined action of alternating stress and corrosive medium for the notch effect of stress concentrated in the grain boundaries.The CF crack propagation is both intergranular and transgranular.

Effect of Cathodic Protection on the Fatigue Crack Growth Behavior of Low Carbon Alloy Steels

The long and short fatigue crack growth (FCG) behavior of 12CrNi3MoV (S1) and 10CrNi5MoV(S2) steel was investigated at cathodic protection in 3.5 % NaCl solution and artificial seawater. The results indicate that long and short FCG show different behavior at cathodic protection. Short FCG is apparently hindered at appropriate cathodic protection potential (-900 mV SCE) and accelerated at over protection potential(-1200 mV SCE). Cathodic protection increases long FCG rate, and the more negative the cathodic protection potential, the greater the long FCG rate. At the same amplitude of stress intensity ( ΔK ), short FCG rate is greater than the long one and their difference becomes less at cathodic protection. The FCG rate in 3.5 % NaCl solution is greater than in artifitial seawater. The FCG rate of S2 steel is bigger then that of S1 steel. The FCG rate of weld bond of S2 steel is lower than that of parent metal and weld beam. In above cases, the anode dissolution, the wedging of corrosion products or deposit and hydrogen embrittlement in long and hort crack tip are also discussed.