This paper involved five kinds of weft-knitted fabrics made from high flame-retardant acrylic/cotton(0/100,30/70,50/50,70/30,100/0).The article adopted the vertical burning method,limiting oxygen index method and Cone...This paper involved five kinds of weft-knitted fabrics made from high flame-retardant acrylic/cotton(0/100,30/70,50/50,70/30,100/0).The article adopted the vertical burning method,limiting oxygen index method and Cone Calorimeter test method for testing fabric flame retardant property.By comparison with these five fabrics,the effects on the properties of high flame-retardant acrylic fiber knitted fabrics due to the content of high flame-retardant acrylic fiber were analyzed.展开更多
A group function relation curve between flux(J) and bulk phase concentration of substrate(S) was set up. The biodegradation kinetic of organic compounds of acrylic fiber wastewater in biofilm is studied(the treatment ...A group function relation curve between flux(J) and bulk phase concentration of substrate(S) was set up. The biodegradation kinetic of organic compounds of acrylic fiber wastewater in biofilm is studied(the treatment technology is coagulation/sedimentation-anoxic/aerobic biofilm process), and the results showed that the concentration of non-degradation pollutants in effluent is 77 mg/L. In aerobic zone, the half-rate constant is 72.84 mg/L, the maximum removal rate of organic compounds at unit area filler is very low, 0.089 g/(m 2·d), which corresponds to the fact that there are some biorefractory compounds in the wastewater.展开更多
The graft copolymerization of acrylic acid (AA) with unswollen and swollen ramie fibers using chromic acid (H 2CrO 4) as the initiator has been studied in the presence of air. The effects of initiator concentration,...The graft copolymerization of acrylic acid (AA) with unswollen and swollen ramie fibers using chromic acid (H 2CrO 4) as the initiator has been studied in the presence of air. The effects of initiator concentration, monomer concentration, perchloric acid (HClO 4) concentration, time of polymerization, reaction temperature, and amount of ramie fibers on the graft percentage have been found out. The graft copolymer was characterized by IR spectra, scanning electron microscopy(SEM), differential thermal analysis (DTA), and thermogravimertric analysis (TGA).展开更多
The polytetrafluoroethylene fiber grafted acrylic acid was used as a cation exchanger. The exchange capacity of the cation fiber is 3.06 mmol/g. The maximum Cu2+ adsorption capacity is 107.48 mg/g. It could be deso...The polytetrafluoroethylene fiber grafted acrylic acid was used as a cation exchanger. The exchange capacity of the cation fiber is 3.06 mmol/g. The maximum Cu2+ adsorption capacity is 107.48 mg/g. It could be desorbed completely by 1mol/L HCl.展开更多
Effect of the cationic surfactant on the hydrolysis of acrylic staple fiber dispersed in alkaline aqueous solution was studied.The cationic dyestuff uptake of the resultant hydrolysates was investigated as well.The re...Effect of the cationic surfactant on the hydrolysis of acrylic staple fiber dispersed in alkaline aqueous solution was studied.The cationic dyestuff uptake of the resultant hydrolysates was investigated as well.The results showed that the surfactant accelerated the hydrolysis of cyano-and ester-groups.The carboxyl content of the hydrolyzed fibers reached the maximum 6.85 mmol/g(i.e.,total molar conversion of the two groups 38.7%) while keeping fiber integrity.The scanning electron microscopy(SEM) images implied that hydrolysis happened both on fiber surface and in the inner part of the fiber in the presence of surfactant.The cationic dye removal due to adsorption onto the hydrolyzed fibers increased with increasing temperature,with the removal 97.4% at 60℃.The adsorption of the fibers followed the Freundlich's adsorption isotherm and the Lagergren's pseudo-second order dynamic equation with the activation energy 5.4 kJ/mol.Unexpectedly,the steric hindrance of access to the inside carboxyl groups of the hydrolyzed fibers caused a low dye sorption capacity,5-6 mg/g.展开更多
In this research, a series of wood-based panels were produced by using wood chips [beech (Fagus Sylvatica L.) and Scotch pine (Pinus sylvestris L.)] as wastes of wood-working workshops and acrylic fibers as wastes of ...In this research, a series of wood-based panels were produced by using wood chips [beech (Fagus Sylvatica L.) and Scotch pine (Pinus sylvestris L.)] as wastes of wood-working workshops and acrylic fibers as wastes of textiles factory. Four kinds of different panels (Eltapan I, II, III and IV) were obtained by mixing these components in different composition (0%, 25% and 50%). Some physical and mechanical properties of the samples taken from these panels were determined in accordance with ASTM D1037-12 and ASTM-C 1113. The values were compared to properties of industrially produced chipboard. As a result, the textile fibers used as additive material reduced density, thermal conductivity and bending resistance of wood panel and increased dimensional stability of wood panel.展开更多
The aim is to evaluate the flexural strength of acrylic resin bars depending on the addiction of glass fibers with or without previous 3-methacryloxypropyl-trimethoxysilane (silane) application. Short fibers (3 mm) we...The aim is to evaluate the flexural strength of acrylic resin bars depending on the addiction of glass fibers with or without previous 3-methacryloxypropyl-trimethoxysilane (silane) application. Short fibers (3 mm) were treated and added to an acrylic resin powder, being further mixed with acrylic liquid to create bars (25 × 2 × 2 mm) of 11 experimental groups (N = 10), according to the interaction of experimental factors: weight % of glass fibers: (0.5;1;3;4;6 and 7) and silane application (with silane (S) or without silane (N)). Flexural strength and scanning microscopy evaluation were performed (SEM). Data (MPa) were submitted to ANOVA and Tukey (α = 5%). A significant difference between groups was observed (p = 0.001): S7%(128.85 ± 35.76)a, S6% (119.31 ± 11.97)ab, S4% (116.98 ± 25.23)ab, N4% (107.85 ± 24.88)abc, S1% (96.29 ± 20.65)bc, S0.5% (89.29 ± 7.33)cd, S3% (89.0 ± 11.27)cd, N3% (86.79 ± 17.63)cd, N1% (85.43 ± 16.44)cd, Control (73.29 ± 25.0)de, N0.5% (59.58 ± 19.46)e. For N groups, it was not possible to include more than 4%wt fibers. SEM showed better fiber-resin interaction for S groups, and fractures around fibers on N groups. Previous silane application enables the addiction of greater quantity of glass fibers and better interaction with the acrylic resin resulting in higher flexural strength. Without silane, fibers seem to act as initial crack points due to poor interaction.展开更多
The dyeing behavior of cationic dyes to acrylic fiber with self-made low temperature dyeing accelerant was investigated in this study.Compared with conventional dyeing,the acrylic yarn was dyed with Cationic Turquoise...The dyeing behavior of cationic dyes to acrylic fiber with self-made low temperature dyeing accelerant was investigated in this study.Compared with conventional dyeing,the acrylic yarn was dyed with Cationic Turquoise Blue X-GB at 85℃ in the presence of accelerant and absence of accelerant,respectively.The influence of low temperature dyeing accelerant on the dyeing mechanism of acrylic fiber dyed with cationic dye was analyzed through kinetics and thermodynamics study.The results show that adding dyeing accelerant can heighten the equilibrium dye-uptake,dyeing rate constants,diffusion coefficients,and shorten half-dyeing time for acrylic fiber dyed with cationic dyes.Furthermore,the partition coefficient,the standard affinity,and the dye saturation value also increased in the dyeing at 85℃.展开更多
Cationic polymer fluid loss additive （CPFL） was prepared by using the reaction of 2,3-epoxypropy- ltrimethyl ammonium chloride （EPTMAC） （as cationic reagent） with the amide group in the molecular structure of th...Cationic polymer fluid loss additive （CPFL） was prepared by using the reaction of 2,3-epoxypropy- ltrimethyl ammonium chloride （EPTMAC） （as cationic reagent） with the amide group in the molecular structure of the sodium salt of partially hydrolyzed polyacrylonitrile fibers （HPAN-Na）. The chemical reaction was determined by studying the infrared absorption peaks of the materials and the products. The results proved that the cationic groups of EPTMAC were successfully grafted onto the HPAN molecular chain. The composition of the molecular chain of the product CPFL was determined by investigation and calculation of the elemental analysis results of the grafted HPAN and the final reaction product CPFL. The drilling fluid performance was evaluated, and the result showed that when the cation content was more than 0.27 mmol/g, the drilling fluid would have good resistance to fluid loss and to pollution from calcium chloride.展开更多
Acrylic fibres are highly crystalline and non-polar polymers,which makes their dyeing a very difficult step that poses real technical challenges.In order to overcome this concern,it is intended in this paper to modify...Acrylic fibres are highly crystalline and non-polar polymers,which makes their dyeing a very difficult step that poses real technical challenges.In order to overcome this concern,it is intended in this paper to modify acrylic fibers by different methods namely cationisation using the Crosscolor DRT then amidoximation using hydroxylamine hydrochloride and ammonium acetate.The resulted samples were dyed then with the bio-colorant extracted from grape marc.The effect of the pretreatment on fibers fine structure using X-ray diffraction and the scanning electron microscope(SEM)images and its correlation with the colour strength of the dyed fabrics was investigated.The dyeing parameters,such as dye bath pH and temperature on the performances of this dyeing process were studied.Good dyeing qualities and new shades varying from brown to grey and dark green have been obtained following process optimization,mordanting and modification of acrylic fibers by the technique of cationisation.展开更多
Vigorous and continued efforts by researchers and engineers have contributed towards maintaining environmental sustainability through the utilization of waste materials in civil engineering applications as an alternat...Vigorous and continued efforts by researchers and engineers have contributed towards maintaining environmental sustainability through the utilization of waste materials in civil engineering applications as an alternative to natural sources.In this study,granite aggregates in asphaltic mixes were replaced by electric arc furnace(EAF)steel slag aggregates with different proportions to identify the best combination in terms of superior performance.Asphalt mixtures showing the best performance were further reinforced with polyvinyl alcohol(PVA),acrylic,and polyester fibers at the dosages of 0.05%,0.15%,and 0.3%by weight of the aggregates.The performance tests of this study were resilient modulus,moisture susceptibility,and indirect tensile fatigue cracking test.The findings of this study revealed that the asphalt mixtures containing coarse steel slag aggregate exhibited the best performance in comparison with the other substitutions.Moreover,the reinforced asphalt mixtures with synthetic fibers at the content of 0.05%exhibited an almost comparable performance to the unreinforced asphalt mixtures.Modifying the asphalt mixtures with PVA,acrylic,and polyester fibers at the proportion of 0.15%have improved the fatigue cracking resistance by 41.13%,29.87%,and 18.97%,respectively.Also,the fiber-modified asphalt mixtures with PVA,acrylic,and polyester have enhanced the fatigue cracking resistance by about 57%,44%,and 39%,respectively.The results of the resilient modulus demonstrated that as the fiber content increase,the resilient modulus of the reinforced asphalt mixtures decreases.Therefore,introducing synthetic fibers at the content of 0.3%has slightly decreased the resilient modulus in comparison with unreinforced mixtures.On the other hand,the results of the mechanisticempirical pavement design showed that the reinforced asphalt mixes with a high content of synthetic fibers have shown lower service life than the control mixes due to the low resilient modulus.On the contrary,based on the laboratory results,the asphalt mixes incorporating PVA,acrylic,and polyester fibers at the proportion of 0.15%have shown the potential to reduce the thickness of the asphalt layer by about 14.9%,11.80%,and 8.70%,respectively.展开更多
Polyethylene terephthalate(PET)and polyethylene(PE)fibers were surface photo-grafted with acrylic acid(AA)by using UV irradiation photochemical initiationduring a continuous winding process within 1-2 min-utes.The gra...Polyethylene terephthalate(PET)and polyethylene(PE)fibers were surface photo-grafted with acrylic acid(AA)by using UV irradiation photochemical initiationduring a continuous winding process within 1-2 min-utes.The grafted fibers were characterized by measure-ments of dye uptaking,moisture regain,pull-out forcesof monofilament from cured matrix,as well as by analy-sis of ESCA and ATR-FTIR spectra.All these resultsconfirm that the surface behavior of the UV-irradiationgrafted fibers was greatly improved.It was also provedthat the original excellent mechanical properties of the fi-bers were well-retained after the surface grafting treat-ment.展开更多
文摘This paper involved five kinds of weft-knitted fabrics made from high flame-retardant acrylic/cotton(0/100,30/70,50/50,70/30,100/0).The article adopted the vertical burning method,limiting oxygen index method and Cone Calorimeter test method for testing fabric flame retardant property.By comparison with these five fabrics,the effects on the properties of high flame-retardant acrylic fiber knitted fabrics due to the content of high flame-retardant acrylic fiber were analyzed.
文摘A group function relation curve between flux(J) and bulk phase concentration of substrate(S) was set up. The biodegradation kinetic of organic compounds of acrylic fiber wastewater in biofilm is studied(the treatment technology is coagulation/sedimentation-anoxic/aerobic biofilm process), and the results showed that the concentration of non-degradation pollutants in effluent is 77 mg/L. In aerobic zone, the half-rate constant is 72.84 mg/L, the maximum removal rate of organic compounds at unit area filler is very low, 0.089 g/(m 2·d), which corresponds to the fact that there are some biorefractory compounds in the wastewater.
文摘The graft copolymerization of acrylic acid (AA) with unswollen and swollen ramie fibers using chromic acid (H 2CrO 4) as the initiator has been studied in the presence of air. The effects of initiator concentration, monomer concentration, perchloric acid (HClO 4) concentration, time of polymerization, reaction temperature, and amount of ramie fibers on the graft percentage have been found out. The graft copolymer was characterized by IR spectra, scanning electron microscopy(SEM), differential thermal analysis (DTA), and thermogravimertric analysis (TGA).
文摘The polytetrafluoroethylene fiber grafted acrylic acid was used as a cation exchanger. The exchange capacity of the cation fiber is 3.06 mmol/g. The maximum Cu2+ adsorption capacity is 107.48 mg/g. It could be desorbed completely by 1mol/L HCl.
基金Environmental Protection Department of Jiangsu Province,China(No.2012009)Suzhou Municipal Government,China(No.SYG201202)
文摘Effect of the cationic surfactant on the hydrolysis of acrylic staple fiber dispersed in alkaline aqueous solution was studied.The cationic dyestuff uptake of the resultant hydrolysates was investigated as well.The results showed that the surfactant accelerated the hydrolysis of cyano-and ester-groups.The carboxyl content of the hydrolyzed fibers reached the maximum 6.85 mmol/g(i.e.,total molar conversion of the two groups 38.7%) while keeping fiber integrity.The scanning electron microscopy(SEM) images implied that hydrolysis happened both on fiber surface and in the inner part of the fiber in the presence of surfactant.The cationic dye removal due to adsorption onto the hydrolyzed fibers increased with increasing temperature,with the removal 97.4% at 60℃.The adsorption of the fibers followed the Freundlich's adsorption isotherm and the Lagergren's pseudo-second order dynamic equation with the activation energy 5.4 kJ/mol.Unexpectedly,the steric hindrance of access to the inside carboxyl groups of the hydrolyzed fibers caused a low dye sorption capacity,5-6 mg/g.
文摘In this research, a series of wood-based panels were produced by using wood chips [beech (Fagus Sylvatica L.) and Scotch pine (Pinus sylvestris L.)] as wastes of wood-working workshops and acrylic fibers as wastes of textiles factory. Four kinds of different panels (Eltapan I, II, III and IV) were obtained by mixing these components in different composition (0%, 25% and 50%). Some physical and mechanical properties of the samples taken from these panels were determined in accordance with ASTM D1037-12 and ASTM-C 1113. The values were compared to properties of industrially produced chipboard. As a result, the textile fibers used as additive material reduced density, thermal conductivity and bending resistance of wood panel and increased dimensional stability of wood panel.
基金The authors thank NAP/MEPA-Esalq-USP for support,assistance and availability of the laboratory and microscopy equipment which enabled the development of this research.
文摘The aim is to evaluate the flexural strength of acrylic resin bars depending on the addiction of glass fibers with or without previous 3-methacryloxypropyl-trimethoxysilane (silane) application. Short fibers (3 mm) were treated and added to an acrylic resin powder, being further mixed with acrylic liquid to create bars (25 × 2 × 2 mm) of 11 experimental groups (N = 10), according to the interaction of experimental factors: weight % of glass fibers: (0.5;1;3;4;6 and 7) and silane application (with silane (S) or without silane (N)). Flexural strength and scanning microscopy evaluation were performed (SEM). Data (MPa) were submitted to ANOVA and Tukey (α = 5%). A significant difference between groups was observed (p = 0.001): S7%(128.85 ± 35.76)a, S6% (119.31 ± 11.97)ab, S4% (116.98 ± 25.23)ab, N4% (107.85 ± 24.88)abc, S1% (96.29 ± 20.65)bc, S0.5% (89.29 ± 7.33)cd, S3% (89.0 ± 11.27)cd, N3% (86.79 ± 17.63)cd, N1% (85.43 ± 16.44)cd, Control (73.29 ± 25.0)de, N0.5% (59.58 ± 19.46)e. For N groups, it was not possible to include more than 4%wt fibers. SEM showed better fiber-resin interaction for S groups, and fractures around fibers on N groups. Previous silane application enables the addiction of greater quantity of glass fibers and better interaction with the acrylic resin resulting in higher flexural strength. Without silane, fibers seem to act as initial crack points due to poor interaction.
基金Science and Technology Department of Zhejiang Province,China (No. 2008C01069-4)
文摘The dyeing behavior of cationic dyes to acrylic fiber with self-made low temperature dyeing accelerant was investigated in this study.Compared with conventional dyeing,the acrylic yarn was dyed with Cationic Turquoise Blue X-GB at 85℃ in the presence of accelerant and absence of accelerant,respectively.The influence of low temperature dyeing accelerant on the dyeing mechanism of acrylic fiber dyed with cationic dye was analyzed through kinetics and thermodynamics study.The results show that adding dyeing accelerant can heighten the equilibrium dye-uptake,dyeing rate constants,diffusion coefficients,and shorten half-dyeing time for acrylic fiber dyed with cationic dyes.Furthermore,the partition coefficient,the standard affinity,and the dye saturation value also increased in the dyeing at 85℃.
基金supported by China National High Technology Research and Development Program(863 Program, 2013AA064803)
文摘Cationic polymer fluid loss additive （CPFL） was prepared by using the reaction of 2,3-epoxypropy- ltrimethyl ammonium chloride （EPTMAC） （as cationic reagent） with the amide group in the molecular structure of the sodium salt of partially hydrolyzed polyacrylonitrile fibers （HPAN-Na）. The chemical reaction was determined by studying the infrared absorption peaks of the materials and the products. The results proved that the cationic groups of EPTMAC were successfully grafted onto the HPAN molecular chain. The composition of the molecular chain of the product CPFL was determined by investigation and calculation of the elemental analysis results of the grafted HPAN and the final reaction product CPFL. The drilling fluid performance was evaluated, and the result showed that when the cation content was more than 0.27 mmol/g, the drilling fluid would have good resistance to fluid loss and to pollution from calcium chloride.
文摘Acrylic fibres are highly crystalline and non-polar polymers,which makes their dyeing a very difficult step that poses real technical challenges.In order to overcome this concern,it is intended in this paper to modify acrylic fibers by different methods namely cationisation using the Crosscolor DRT then amidoximation using hydroxylamine hydrochloride and ammonium acetate.The resulted samples were dyed then with the bio-colorant extracted from grape marc.The effect of the pretreatment on fibers fine structure using X-ray diffraction and the scanning electron microscope(SEM)images and its correlation with the colour strength of the dyed fabrics was investigated.The dyeing parameters,such as dye bath pH and temperature on the performances of this dyeing process were studied.Good dyeing qualities and new shades varying from brown to grey and dark green have been obtained following process optimization,mordanting and modification of acrylic fibers by the technique of cationisation.
基金This work was supported by Universiti Tenaga Nasional(UNITEN)through BOLD Refresh Publication Fund 2021 under Grant J5100D4103-BOLDREFRESH2025-CENTRE OF EXCELLENCE.
文摘Vigorous and continued efforts by researchers and engineers have contributed towards maintaining environmental sustainability through the utilization of waste materials in civil engineering applications as an alternative to natural sources.In this study,granite aggregates in asphaltic mixes were replaced by electric arc furnace(EAF)steel slag aggregates with different proportions to identify the best combination in terms of superior performance.Asphalt mixtures showing the best performance were further reinforced with polyvinyl alcohol(PVA),acrylic,and polyester fibers at the dosages of 0.05%,0.15%,and 0.3%by weight of the aggregates.The performance tests of this study were resilient modulus,moisture susceptibility,and indirect tensile fatigue cracking test.The findings of this study revealed that the asphalt mixtures containing coarse steel slag aggregate exhibited the best performance in comparison with the other substitutions.Moreover,the reinforced asphalt mixtures with synthetic fibers at the content of 0.05%exhibited an almost comparable performance to the unreinforced asphalt mixtures.Modifying the asphalt mixtures with PVA,acrylic,and polyester fibers at the proportion of 0.15%have improved the fatigue cracking resistance by 41.13%,29.87%,and 18.97%,respectively.Also,the fiber-modified asphalt mixtures with PVA,acrylic,and polyester have enhanced the fatigue cracking resistance by about 57%,44%,and 39%,respectively.The results of the resilient modulus demonstrated that as the fiber content increase,the resilient modulus of the reinforced asphalt mixtures decreases.Therefore,introducing synthetic fibers at the content of 0.3%has slightly decreased the resilient modulus in comparison with unreinforced mixtures.On the other hand,the results of the mechanisticempirical pavement design showed that the reinforced asphalt mixes with a high content of synthetic fibers have shown lower service life than the control mixes due to the low resilient modulus.On the contrary,based on the laboratory results,the asphalt mixes incorporating PVA,acrylic,and polyester fibers at the proportion of 0.15%have shown the potential to reduce the thickness of the asphalt layer by about 14.9%,11.80%,and 8.70%,respectively.
文摘Polyethylene terephthalate(PET)and polyethylene(PE)fibers were surface photo-grafted with acrylic acid(AA)by using UV irradiation photochemical initiationduring a continuous winding process within 1-2 min-utes.The grafted fibers were characterized by measure-ments of dye uptaking,moisture regain,pull-out forcesof monofilament from cured matrix,as well as by analy-sis of ESCA and ATR-FTIR spectra.All these resultsconfirm that the surface behavior of the UV-irradiationgrafted fibers was greatly improved.It was also provedthat the original excellent mechanical properties of the fi-bers were well-retained after the surface grafting treat-ment.
