Experimental investigation of a counter-rotating compressor with boundary layer suction

This paper presents the aspirated modification of a dual-stage counter-rotating compressor which contains inlet guide vanes（IGVs）, two counter-rotating rotors（R1, R2）, and outlet guide vanes（OGVs）.Uniform circular holes are circumferentially distributed over the rotors＇ tips on the shroud casing which are designed to remove the low-energy fluid near the shroud casing.OGVs are hollow blades with two slots designed on the suction side which can better control the flow on the suction surface through boundary layer suction.Related works about the experiments have been carried out since June 2012 and the effect of flow suction on the performance of the compressor is investigated in detail.Characteristic lines at a 70% corrected rotating speed are tested and those with higher rotating speeds will be studied in the near future.Experimental results indicate that boundary layer suction can improve the compressor characteristics and the best suction methodology varies along the operating line.At the near stall condition, suction from the R2 tip region can obviously increase the efficiency and the total pressure ratio, as well as improve the flow capacity.Isentropic efficiency can be maximally increased by 4.24% with an increase of 1.94% in massflow under a suction flow of 160 m3/h.Suction at the R1 position with a suction rate below 0.35% in a high flow situation can make the performance of the compressor better than others.Around the peak efficiency point, boundary layer suction from the slots of OGVs is the best choice in improving the efficiency, but it causes a 0.1% loss in the total pressure ratio.

Preparation and property of seal coating for gas turbine compressor

Double-layer structure of seal coating which consisted of a Ni5Al bond coating and a Ni25 graphite top coating were prepared on steel substrate of gas turbine compressor cylinder block.Bond coating was prepared by atmospheric plasma spraying and top coating was prepared by flame spraying.The microstructure,mechanical properties and abradability of the coating were characterized by scanning elec-tron microscope(SEM),hardness tester,universal testing machine,thermal shock testing machine and abradability testing machine.The res-ults show that the overall spraying structure of the seal coating is uniform,the nickel metal phase is the skeleton supporting the entire coat-ing,and the coating is well bonded without separation.The seal coating has a bonding strength of not less than 7.7 MPa,excellent thermal stability,and thermal shock resistance cycle numbers at 500℃more than 50;the scratch length,deepest invasion depth and wear amount of the coating increase with rise of test temperature,with almost no coating adhesion,indicating that the seal coating has excellent abradability.

Numerical Study of Co-flow Jet Control on Corner Separation in Compressor Cascade

The design objectives of modern aircraft engines include high load capacity,efficiency,and stability.With increasing loads,the phenomenon of corner separation in compressors intensifies,affecting engine performance and stability.Therefore,the adoption of appropriate flow control technology holds significant academic and engineering significance.This study employs the Reynolds-averaged Navier-Stokes(RANS)method to investigate the effects and mechanisms of active/passive Co-flow Jet(CFJ)control,implemented by introducing full-height and partial height jet slots between the suction surface and end wall of a compressor cascade.The results indicate that passive CFJ control significantly reduces the impact of corner separation at small incidence,with partial-height control further enhancing the effectiveness.The introduction of active CFJ enables separation control at large incidence,improving blade performance under different operating conditions.Active control achieves this by reducing the scale of corner separation vortices,effectively reducing the size of the separation region and enhancing blade performance.

VIBRATION CHARACTERISTIC INVESTIGATION OF COUNTER-ROTATING DUAL-ROTOR IN AERO-ENGINE

Two methods for vibration characteristic investigation of the counter-rotating dual-rotors in an aero-en- gine are put forward. The two methods use DAMP tool on the MSC. NASTRAN platform and develope the re- solving sequence. Vibration characteristics of a turbofan engine are analyzed by using the two methods. Com- pared with results calculated using transfer matrix method and test results, the two methods are valuable and have great potential in practical applications for vibration characteristic investigation of aero-engines with high thrust-weight ratio.

VIBRATION NUMERICAL ANALYSIS OF COUNTER-ROTATING TURBINE WITH WAKE-FLOW USING FLUID-STRUCTURE INTERACTION METHOD

The design of counter-rotating turbine is one of new techniques to improve the thrust-weight ratio of jet propulsion engines.Numerical analysis of a low pressure（LP）counter-rotating turbine rotor blade is presented by using ANSYS/CFX software.Interaction of aerodynamics and solid mechanics coupling in the computation is applied.In some rating of turbine,stress distribution and vibration characteristics of low pressure turbine（LPT）blade are computed.The wake aerodynamic forces and LPT blade vibration are transformed in frequency domain using fast Fourier transform（FFT）method.The results show that under wake aerodynamic force excitation,the first order modal vibration is more easily aroused and the higher order response cannot be ignored.Moreover,with different temperature fields,the vibration responses of blade are also different.

Effects of Shielding Coatings on the Anode Shaping Process during Counter-rotating Electrochemical Machining

Electrochemical machining （ECM） has been widely used in the aerospace, automotive, defense and medical industries for its many advantages over traditional machining methods. However, the machining accuracy in ECM is to a great extent limited by the stray corrosion of the unwanted material removal. Many attempts have been made to improve the ECM accuracy, such as the use of a pulse power, passivating electrolytes and auxiliary electrodes. However, they are sometimes insufficient for the reduction of the stray removal and have their limitations in many cases. To solve the stray corrosion problem in CRECM, insulating and conductive coatings are respectively used. The different implement processes of the two kinds of coatings are introduced. The effects of the two kinds of shielding coatings on the anode shaping process are investigated. Numerical simulations and experiments are conducted for the comparison of the two coatings. The simulation and experimental results show that both the two kinds of coatings are valid for the reduction of stray corrosion on the top surface of the convex structure. However, for insulating coating, the convex sidewall becomes concave when the height of the convex structure is over 1.26 ram. In addition, it is easy to peel off by the high-speed electrolyte. In contrast, the conductive coating has a strong adhesion, and can be well reserved during the whole machining process. The convex structure fabricated by using a conductive iron coating layer presents a favorable sidewall profile. It is concluded that the conductive coating is more effective for the improvement of the machining quality in CRECM. The proposed shielding coatings can also be employed to reduce the stray corrosion in other schemes of ECM.

New Bulb Turbine with Counter-rotating Tandem-runner

With the increasing demand for the clean sustainable power, the turbine design urgently turns to increase the capability significantly toward higher head for generating larger power. Currently, there are many studies in the field of the bulb turbine with single-stage runner, though reports about counter-rotating tandem-runner are rare. However, the further high-head application with the single-stage runner is very difficult to achieve due to the limit of the specific speed. In this paper, a new bulb turbine with the tandem-runner is designed in order to substantially increase the applicable limit toward higher head with larger power. A half of the net head is absorbed by the frontal runner which can generate output power, while the remaining half is absorbed by the rear runner. To generate the Euler energy required for the rear runner, the frontal runner has the counter-rotation against the rear runner so that the counter-rotating tandem-runner can meet the purpose of double head and power under the same size as the conventional bulb turbine. Supply and demand of Euler energy between the two runners are thoroughly optimized through the detailed flow analysis, in order to secure the stable operation. As a result, the interference of Euler energies between the outflow from the frontal runner and the inflow to the rear runner is confirmed to be very small on the counter-rotating interface between the two runners. The prediction method of on-cam performance between the two adjustable runners is also developed numerically, which provides optimal flow between the two runners. This research provides a theoretical basis for the optimal design and operation of the counter-rotating tandem-runner bulb turbines.

Modeling and Simulation of aCounter-Rotating Turbine System for Underwater Vehicles

The structure of a counter-rotating turbine of an underwater vehicle is designed by adding the counter-rotating second-stage turbine disk to the conventional single-stage turbine. The available kinetic energy and the absorption power of the auxiliary system are calculated at different working conditions, and the results show that the power of the main engine and auxiliary system at the counter-rotating turbine system matches well with each other. The technology scheme of the counter-rotating turbine system is proposed, then the experimental simulation of the lubricating oil loop, fuel loop, and seawater loop is completed. The simulation results indicate that the hydraulic transmission system can satisfy the requirements for an underwater vehicle running at a steady sailing or variable working conditions.

Link Resource Allocation in Counter-Rotating Seam of Low-Orbit Satellite Network

This paper studies the communication problem at the counter-rotating seam of the low-orbit satellite based on the walker constellation. The counter-rotating seam has a short life cycle, low capacity, and dynamic geometric parameters. To better utilize the scarce link resources at the seam, increase network throughput, and approach the physical limits of the link throughput at the seam, an initial phase condition that maximizes the relative rotational joint link throughput is calculated. In the experimental simulation results using the Iridium system as an example, it is shown that better throughput can be obtained under the initial conditions, and the throughput is improved by about 30%.

Isolated attosecond pulse generation with few-cycle two-color counter-rotating circularly polarized laser pulses

Most of the schemes for generating isolated attosecond pulses（IAP） are sensitive to the carrier-envelope phase（CEP）of the driving lasers. We propose a scheme for generating IAP using two-color counter-rotating circularly polarized（TCCRCP） laser pulses. The results demonstrate that the dependence of the IAP generation on CEP stability is largely reduced in this scheme. IAP can be generated at most of CEPs. Therefore, the experiment requirements become lower.

Numerical Flow Simulation in Turbine Mode of Counter-Rotating Type Pumping Unit to Cooperate with Wind Turbine

This serial research has proposed the hybrid power system combined the wind power unit with the counter-rotating type pump-turbine unit, to provide the constant output for the grid system, even at the suddenly fluctuating/turbulent wind circumstance. In this paper, the tandem impellers prepared for the counter-rotating type pumping unit were operated at the turbine mode, and the performances and the flow conditions were investigated numerically with accompanying the experimental results. Even though providing the pumping unit for the turbine mode, the maximum hydraulic efficiency is close to one of the counter-rotating type hydroelectric unit designed exclusively for the turbine mode. Besides, the runners/impellers of the unit work evidently so as to coincide the angular momentum change through the front runners/impellers with that through the rear runners/impellers, namely to take the axial flow at not only the inlet but also the outlet, without the guide vanes. From these results, it can be concluded that this type unit is effective to work at not only the pumping but also the turbine modes.

Semi-integer harmonic generation from an argon atom by bichromatic counter-rotating circularly polarized laser field

We theoretically investigated the properties of the high-order harmonic generation from an argon atom by bichromatic counter-rotating circularly polarized(BCCP)laser field.The harmonic emission processes have been illustrated by numerically solving the two-dimensional time-dependent Schr¨odinger equation of an atom in intense laser fields.It is found that with the decrease of the right-circularly polarized laser wavelength,the harmonic spectra are gradually splitting and the harmonic orders move towards the higher frequency.Meanwhile,the integer and semi-integer harmonic emission will be generated when the frequency ratios of right-and left-circularly polarized lasers are semi-integer.The emission mechanism of the semi-integer-order harmonics has been investigated by using the rules of photon absorption and emission.

Effects of initial electronic state on vortex patterns in counter-rotating circularly polarized attosecond pulses

We theoretically investigate the effects of different electronic states as the initial state on the vortex patterns in photoelectron momentum distributions(PMDs)from numerical solutions of the two-dimensional(2D)time-dependent Schrodinger equation(TDSE)of He^(+)with a pair of counter-rotating circularly polarized attosecond pulses.It is found that the number of spiral arms in vortex patterns is equal to the number of the absorbed photons when the initial state is the ground state.However,the number of spiral arms in vortex patterns is always two more than the number of the absorbed photons when the initial state is the excited state.This sensitivity is attributed to the initial electron density distribution.In addition,we have demonstrated the PMDs for different initial electronic states with the same wavelengths and analyzed their corresponding physical mechanisms.It is illustrated that the method presented can be employed to effectively control the distribution of the electron vortices.

Power Stabilization System with Counter-Rotating Type Pump-Turbine Unit for Renewable Energy

Traditional type pumped storage system contributes to adjust the electric power unbalance between day and night, in general. The pump-turbine unit is prepared for the power stabilization system, in this serial research, to provide the constant power with good quality for the grid system, even at the suddenly fluctuating/turbulent output from renewable energies. In the unit, the angular momentum changes through the front impeller/runner must be the same as that through the rear impeller/runner, that is, the axial flow at the outlet should be the same to the axial flow at the inlet. Such flow conditions are advantageous to work at not only the pumping mode but also the turbine mode. This work discusses experimentally the performance of the unit, and verifies that this type unit is very effective to both operating modes.

Role of potential on high-order harmonic generation from atoms irradiated by bichromatic counter-rotating circularly polarized laser fields

We investigate high-order harmonic generation from atoms irradiated by bichromatic counter-rotating circularly polarized laser pulses by numerically solving the time-dependent Schrödinger equation.It is found that the minimum energy position of the harmonic spectrum and the non-integer order optical radiation are greatly discrepant for different atomic potentials.By analyzing the quantum trajectory of the harmonic emission,discrepancies among the harmonic spectra from different potentials can be attributed to the action of the potential on the ionized electrons.In addition,based on the influence of the driving light intensity on the overall intensity and ellipticity of higher order harmonics,the physical conditions for generating a high-intensity circularly polarized harmonic can be obtained.

Counter-Rotating Type Horizontal-Axis Bidirectional Propellers for Tidal Stream Power Unit

Tidal stream power units with horizontal-axis propellers are one of promising technologies for generating the renewable green energy. The ebb and flow require that the power unit must operate in bidirectional tidal streams. Hence a tidal stream power unit with counter-rotating type horizontal-axis bidirectional propellers is proposed in this paper. The blades with fully-symmetrical hydrofoils were optimized numerically. The output and flow conditions predicted by the computational fluid dynamics simulations are compared with the results of the wind tunnel experiments at the higher tip speed ratios, which are of expected usual operating conditions of this unit. The numerical and experimental results show good agreements. It is also confirmed that the flow discharged from the counter-rotating type propellers has no swirling component, though the single propeller generates the unacceptable swirling component.

A Numerical Prediction of Tip Vortices from Tandem Propellers in the Counter-Rotating Type Tidal Stream Power Unit

Ocean energy has a potential of providing a large amount of renewable energy around the world. One of the forms of ocean energy, tidal stream power is widely recognized as the continuous, predictable and eco-friendly ocean energy source. Unique tandem propellers that can counter-rotate have been designed to generate electric power effectively from a tidal stream. This type of power unit has several advantages compare to the conventional unit with a single propeller. At the design of the tidal stream power unit, it is important to investigate the structure of the tip vortex tubes shedding to predict the load of the propeller. In this research, we investigated the tip vortex shedding using the CFD method for the conventional single propeller and counter-rotating type tandem propellers and estimated the performance efficiency using RANS (Reynolds Averaged Navier-Stokes) model and we confirmed the limitation of RANS model on the calculation of the tip vortex stretching.

Counter-Rotating Type Pump-Turbine Unit Stabilizing Momentarily Fluctuating Power from Renewable Energy Resources

It is difficult for renewable energy resources to provide constant power with excellent quality for the grid system. This serial research proposes a power stabilization system with a pumped storage to guarantee power quality and capacity, while the outputs from the energy resources are at unstable and/or fluctuating conditions. The power stabilization system with a counter-rotating type pump-turbine unit was prepared and operated at the pumping and the turbine modes. The unit composed of the tandem impellers/runners connected to the inner and the outer armatures of the unique motor/generator. The experiments have verified that this type pump-turbine unit is reasonably effective to stabilize momentarily/instantaneously the fluctuating power from the renewable energy resources.

Hybrid URANS/LES Method of Flow Fields in Axial-flow Compressor Rotor Rotor

Accurate and efficient prediction of the aerodynamic performance and flow details of axial-flow com-pressors is of great engineering application value for the aerodynamic design and flow control of axial-flow compres-sors.In this work,a delayed detached eddy simulation method is developed and applied to numerically simulate the tur-bulent channel flow and the aerodynamic performance of NASA Rotor 35.Several acceleration techniques including parallel implementation are also used to speed up the iteration convergence.The mean velocity distribution and Reyn-olds stress distribution in the boundary layer of turbulent channel flow and the aerodynamic performance curve of NASA Rotor 35 are predicted.The good agreement between the present delayed detached eddy simulation results and the available direct numerical simulation results or experimental data confirms the effectiveness of the developed meth-od in the accurate and efficient prediction of complex flow in turbomachinery.

解决农产品配送“断链”的光伏冷链小车设计

在现有普通农用电动货运三轮车的基础上,通过增加1.3m^(3)保温车厢、600Wp太阳能电池板、4块12V100Ah蓄电池、110W直流压缩机等设备,先计算车厢从35℃降至-10℃所需要的冷量,再综合验证组件与蓄电池满足小车一天的制冷与行驶需求。通过精确的系统匹配及智能温度控制,改造成太阳能智能冷链物流小车,很好的解决了现在冷链物流配送中“最后一公里”空缺的问题,经过测试达到设计要求。本车可直接开到田间地头,有方便快捷、耐用、不付电费、造价低等优势,是现代农业物流冷链运输必不可少的中转设备,实现了农村鲜活农产品采摘−物流中心−用户的无缝对接。