Stability analysis of the sliding process of the west slope in Buzhaoba Open-Pit Mine

To study the stability of the west slope in Buzhaoba Open-Pit Mine and determine the aging stability coefficient during slide mass development, the deformation band of the west slope and the slide mass structure of the 34,600 profile are obtained on the basis of hydrology, geology, and monitoring data.The residual thrust method is utilized to calculate the stability coefficients, which are 1.225 and 1.00 under sound and transfixion conditions, respectively. According to the rock damage and fragmentation and the principle of mechanical parameter degradation, the mechanical models of the slide mass development of the hard and soft rock slopes are established. An integrated model for calculating the slope stability coefficient is built considering water, vibration, and other external factors that pertain to the structural plane damage mechanism and the generating mechanism of the sliding mass. The change curve of the stability coefficient in the slide mass development is obtained from the relevant analyses,and afterwards, the stability control measures are proposed. The analysis results indicate that in the cracking stage of the hard rock, the slope stability coefficient decreases linearly with the increase in the length Lbof the hard rock crack zone. The linear slope is positively correlated to rock cohesion c. In the transfixion stage of the soft rock, the decrease speed of the stability coefficient is positively correlated to the residual strength of the soft rock. When the slope is stable, the stability coefficient is in a quadratic-linear relationship with the decreased height Dh of the side slope and in a linear relationship with anchoring force P.

Optimisation Method for Determination of Crack Tip Position Based on Gauss-Newton Iterative Technique

In the digital image correlation research of fatigue crack growth rate,the accuracy of the crack tip position determines the accuracy of the calculation of the stress intensity factor,thereby affecting the life prediction.This paper proposes a Gauss-Newton iteration method for solving the crack tip position.The conventional linear fitting method provides an iterative initial solution for this method,and the preconditioned conjugate gradient method is used to solve the ill-conditioned matrix.A noise-added artificial displacement field is used to verify the feasibility of the method,which shows that all parameters can be solved with satisfactory results.The actual stress intensity factor solution case shows that the stress intensity factor value obtained by the method in this paper is very close to the finite element result,and the relative error between the two is only−0.621%;The Williams coefficient obtained by this method can also better define the contour of the plastic zone at the crack tip,and the maximum relative error with the test plastic zone area is−11.29%.The relative error between the contour of the plastic zone defined by the conventional method and the area of the experimental plastic zone reached a maximum of 26.05%.The crack tip coordinates,stress intensity factors,and plastic zone contour changes in the loading and unloading phases are explored.The results show that the crack tip change during the loading process is faster than the change during the unloading process;the stress intensity factor during the unloading process under the same load condition is larger than that during the loading process;under the same load,the theoretical plastic zone during the unloading process is higher than that during the loading process.

CRACK TIP STRUCTURE AND DUCTILE-BRITTLE TRANSITION IN BULK SINGLE CRYSTALS

Based on the crack tip structure a new model of ductile -brittle transition was proposed. Using this new model we calculated the dependence of the transition temperature-strain rate over a wide range of strain rate. Finally the significance of this new model is discussed in detail.

Thermomechanical analysis of triangular zone cracks in vertical continuous casting slabs based on viscoelastic-plastic model

The triangular zone cracks in 2101 duplex stainless steel produced by the vertical continuous caster have troubled company A for a long time. To simulate the temperature and thermal stress distributions in the solidification process of 2101 duplex stainless steel produced by the vertical continuous caster, a two-dimensional viscoelastic-plastic thermomechanically coupled finite element model was established by the secondary development of the commercial nonlinear finite element analysis software MSC Marc. The results show that the thermal stress on the surface reaches a maximum at the exit of the mould, and the highest thermal stresses at the centre of the wide face and the narrow face are 75 and 115 MPa, respectively. Meanwhile, the internal temperature of slab is still higher than the solidus temperature, resulting in no thermal stress. The slab shows different high-temperature strengths and suffers from different stresses at different positions; thus, the risk of cracking also varies. At a location of 6-8 m from the meniscus, the temperature of the triangular zone is 1270-1360℃ and the corresponding permissible high-temperature strength is about 10-30 MPa, while the thermal stress at this time is 60 MPa, which is higher than the high-temperature strength. As a result, triangular zone cracks form easily.

Effects of Ag Addition on Precipitation and Fatigue Crack Propagation Behavior of a Medium-Strength Al–Zn–Mg Alloy

Effects of trace addition of Ag on the fatigue crack propagation behavior and microstructure of a mediumstrength aged AI-Zn-Mg alloy were investigated in the present work. The results show that a combination of enhanced tensile strength and improved fatigue crack propagation resistance in Al-Zn-Mg alloys is achieved with small addition of Ag. The enhanced strength is attributed to the high density of η＇ precip- itates within the grains and narrow precipitate free zones in the vicinity of grain boundaries. The main contribution to the improvement of fatigue crack propagation resistance comes from the coarser precipitates within the grains. When subjected to two-step aging. Ag-added alloy shows larger semi-coherent matrix precipitates. These relatively coarser precipitates increase the homogeneity of deformation and therefore improve the fatigue crack propagation resistance. In addition, microstructure analysis indicates that the size and distribution of inclusions as well as the grain structures of Al-Zn-Mg alloys are independent of Ag addition.